MEGATRONIX Viking VS 2000 Installation Manual - page 16
Low check level
Hi check level
4
Start / Stop the system for TESTING & ADJUSTMENT
5
-
Without Shock
sensor Test Mode
With Shock Sensor
Test Mode
6
+
Exit
: Press the
button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
ENGINE CHECKING TACH. / RPM LEARNING
Important Note: You must program the “Tach Signal” before trying to remote start.
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
2. Push the Valet switch 10 times and holding in on the 10 push until five chirps with a long chirp is hearing
then release the valet switch.
and
3. Press and release the transmitter
buttons at the same time once to set the “Engine Checking
TACH.” [1] LED flash, [1] chirp to confirm this setting.
4. Press and release the transmitter
button once, [1] LED flash, [1] chirp to indicate the system in features
“RPM Learning mode”.
5. Start the vehicle with the key. (While the engine is running, the parking light & LED will flash, If don’t,
please check tachometer White/Red wire connection. (H7/8)
6. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two seconds.
The RPM signal is learned.
7. Turns off the ignition switch to stop engine running.
Once you complete step 7, you can adjust and test “Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well:
a. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
b. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
3. If the crank time is too short, (The engine did not successfully run before the starter quit cranking):
button on the transmitter to turn ignition lights “OFF”.
a. Press the
button on the transmitter to set proper “Check Level ” to Hi position. [2] LED flashes,
Press
[2] chirps to confirm this setting
b. Repeat the step1 – 4.
4. If the crank time is too long, (Engine is successfully running, while the starter is still cranking):
button on the transmitter to stop engine running.
a. Press the
Press
button on the transmitter to set proper “ Check Level ” to Low position. [1] LED flash,
[1] chirp to confirm this setting
b. Repeat the step1 – 4.
ENGINE CHECKING VOLTAGE
Important Note: The “Check Level” for most vehicles would be set in “Hi Check Level”, while in “Engine
Check Voltage mode”, the “Check Level” must be set at “HI” position first.
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
2. Push the Valet switch 10 times and holding in on the 10 push until five chirps with a long chirp is hearing
then release the valet switch.
3. Press the transmitter
and buttons at the same time to set the “Engine Checking Voltage”. [2] LED
flashes, [2] chirps to confirm this setting.
4. Press
button on the transmitter to set “Check Level” to “HI” position. [2] LED flashes, [2] chirps to
confirm this setting.
Once you complete step 4, you can adjust and test “Start Timer” as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything go well, Wait for 20 seconds:
a. If the engine still running.
I. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
II. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
16