MEGATRONIX Viking VS 2000 Installation Manual - page 12
A. PROGRAMMING THE REMOTE TRANSMITTER:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the valet
switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the
signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “
I
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
nd
2. Push the Valet switch 2 times and holding in on 2 push until one chirp with a long chirp is hearing then
release the valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
a. The siren chirps and LED pause will indicate newly setting.
b. The system would advance to [2] LED flash, [2] chirp. (The factory default settings is always [1] LED
flash, [1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Four Chirps /
One Chirp /
Two Chirps /
Three Chirps /
Press
LED four pulse
LED one pulse
LED two pulse
LED three pulse
Transmitter
Button
Factory Default Setting
All chirps on
Siren chirp on only
Horn chirp on only
All chirps off
1
Passive arming with
passive door
locking.
Passive arming
without passive door
locking
Active arming
2
Automatic Rearm on
Automatic Rearm off
3
Instantly Door Ajar
Warning
45 seconds delay
Door Ajar Warning.
4
Passive Car-jack
mode
Without Car-jack mode
Active Car-jack mode
5
+
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
3 / 45 seconds Delay Door Ajar Warning:
This feature controls the error chirp that is generated if the system is armed with the door trigger active. This
useful in a vehicle that has a long dome light delays after the door has been closed. If the system is armed
before the dome light has turned off, the security system will generate the door trigger error chirp. Use this
feature to disable the door open error chirp.
ALARM FEATURE “
II
” PRORAMMING:
1 . Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
2 . Push the Valet switch 4 times and holding in on the 4 push until two chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 . Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Four Chirps / LED
four pulse
One Chirp / LED
one pulse
Two Chirps / LED
two pulse
Three Chirps / LED
three pulse
Press
T
ransmitte
r
Button
Factory Default
Setting
Door lock with
“Comfort Feature”
0.8-second Door
lock pulses.
3.5-second Door
lock pulse.
Double pulse unlock
1
12