NAD T535 Owner's Manual - page 8
IDENTIFICATION OF CONTROLS
REAR PANEL
1 MIXED AUDIO OUT: Connect to the corresponding analog audio
input of an amplifier, receiver or stereo system.
2 5.1CH AUDIO OUT: The T 535 contains a multi-channel decoder. It
enables playback of discs recorded in multi-channel surround without
the need for an optional decoder.
Connect to the corresponding multi-channel audio input of a receiver
or a processor.
3 DIGITAL OUT (COAXIAL, OPTICAL): Connect the optical or coaxial
digital OUT ports to the corresponding S/PDIF digital input of a
recording component such as a CD recorder, DAT deck, computer
soundcard or other digital processors.
4 IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 535 from a remote location. Most NAD products with IR
OUT are fully compatible with the T 535.
5. RS-232: Connect this interface via RS-232 serial cable (not supplied)
to any Windows® compatible PC to allow remote control of the T 535
through NAD’s proprietary PC software or other compatible external
controllers.
Please log on to www.nadelectronics.com/software for the latest PC
interface control software.
NAD is a certified partner of AMX and Crestron and fully supports these
external devices. See your NAD audio specialist for more information.
6. SCART/RGB OUT (Euro model/PAL only): Connect the T 535’s
[SCART/RGB OUT] to the SCART/RGB video input of a compatible video
monitor/TV. Be sure to observe the correct orientation of the SCART/
RGB plug.
7 HDMI OUT: Using a HDMI cable (not supplied), connect the HDMI OUT
jack to the corresponding HDMI input jack of an HDTV, a projector or an
A/V Receiver.
NOTES
• ToggletheHDMIbuttonofDVD9remotecontroltoturnONorOFF
HDMIoutput.WhenturnedON,“HDMION”willbedisplayedintheVFD
followedbytheapplicableresolutionsetting.
• Therewillbenocomponentvideooutputat“HDMION”.
• HDMIbuttonintheDVD9remotecontrolwillnotelicitanyresponseif
theHDMIcableiseitherunpluggedfromtheHDMIOUTterminalornot
connectedtoaHDMI-capableTV/monitor.
WARNING
BeforeconnectinganddisconnectinganyHDMIcables,boththeT535
andtheancillarysourcemustbepoweredOFFandunpluggedfromthe
ACoutlet.Failuretoobservethispracticemaycausepermanentdamage
toallequipmentconnectedviaHDMIsockets.
8 VIDEO OUT/S-VIDEO OUT: Connect to video input of the monitor/
television using quality dual-RCA and/or S-Video cables designed for
video signals. In general, the S-Video connection is superior and should
be used if your TV/monitor provides the corresponding input.
9 COMPONENT VIDEO OUT: Connect the T 535’s COMPONENT VIDEO
OUT to the component video input of a compatible video monitor/TV
or an A/V Receiver with applicable component video input. Be sure to
observe consistency in connecting the appropriate Y, Cb/Pb, Cr/Pr jacks
to the corresponding sources/inputs. Do not rely purely on the color
coding of the jacks, which may not always be consistent among brands.
The T 535’s component-video output is a fully wide-band output,
compatible with all HDTV formats. On-screen display menu is also
shown at component video output.
10 AC POWER INLET: Connect to the supplied IEC-standard removable
AC power cord or a compatible cord.
3
4
5
6
7
8
9
1
2
10
ATTENTION!
PleasemakesurethattheT535ispoweredofforunpluggedbeforemakinganyconnections.Itisalsoadvisabletopower-downorunplugallassociated
componentswhilemakingorbreakinganysignalorACpowerconnections.
8
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ