1. DL manuals
  2. NEC
  3. Telephone System
  4. SL1000
  5. Programming Manual

NEC SL1000 Programming Manual

Summary of SL1000

  • Page 1

    Programming manual a50-031167-002 eu issue 1.0 may 2011.

  • Page 2: Copyright

    Copyright nec corporation reserves the right to change the specifications, functions, or features at any time without notice. Nec corporation has prepared this document for use by its employees and customers. The informa- tion contained herein is the property of nec corporation and shall not be repr...

  • Page 3: Chapter 1 Introduction

    Chapter 1 introduction section 1 before you start programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 section 2 how to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4: Table Of Contents

    10-61 : relay port setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54 10-62 : netbios setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Table Of Contents

    15-09 : virtual extension ring assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-140 15-10 : incoming virtual extension ring tone order setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-141 15-11 : virtual e...

  • Page 6: Table Of Contents

    20-45 : remote watch setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-212 20-46 : security sensor setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 7: Table Of Contents

    Program 24 : hold/transfer setup 24-01 : system options for hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-270 24-02 : system options for transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 8: Table Of Contents

    Program 34 : tie line setup 34-01 : e&m tie line basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-331 34-02 : e&m tie line class of service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 9: Table Of Contents

    47-11 : inmail answer table options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-400 47-12 : inmail answer schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 10: Table Of Contents

    84-15 : h.323/sip phone keep alive setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-481 84-16 : voipdb limiter control gain setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4...

  • Page 11: Table Of Contents

    90-57 : backup recovery data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-568 90-58 : restore recovery data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12: List Of Tables

    Table 1-1 keys for entering data (sl1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 table 1-2 keys for entering data (sl1100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 13: Introduction

    S ection 1 before you start programming before customizing your system be sure to read this chapter first. This chapter provides you with detailed information about the system programs. By changing a pro- gram, you change the way the feature associated with that program works. In this chapter, you f...

  • Page 14

    2 15-07-01 tells you to enter the programming mode, dial 150701 from the telephone dial pad. After you do, you will see the message “15-07-01 tel” on the first line of the telephone display. This indicates the pro- gram number (15-07), item number (01), and that the options are being set for the ext...

  • Page 15

    Change the passwords, use 90-02 : programming password setup on page 2-502 . Password user name level programs at this level ****** nec-i 1 (mf) manufacture level (mf) : 80-02, 81-04, 81-05, 82-02 (sl1000) , 82-05, 82-08 (sl1100) 12345678 tech 2 (in) installation (in) : all programs in this section ...

  • Page 16

    To save a customer’s database, a blank compact flash (cf) card is required. Insert the cf card into the cpu and, using program 90-03, save the software to the cf card. (program 90-04 is used to reload the customer data if necessary.) note that a cf card can only hold one customer database. Each data...

  • Page 17

    When you want to ... Telephone programming change program number - change index number move cursor to right cursor key (right) table 1-2 keys for entering data (sl1100) when you want to ... Telephone programming enter data into program 0 ~ 9, * , # line key (1 ~ 6) next index cursor key (up) prior i...

  • Page 18

    Use this keypad digit ... When you want to ... 3 enter characters : d-f, d-f, 3 . 4 enter characters : g-i, g-i, 4 . 5 enter characters : j-l, j-l, 5 . 6 enter characters : m-o, m-o, 6 . 7 enter characters : p-s, p-s, 7 . 8 enter characters : t-v, t-v, 8 . 9 enter characters : w-z, w-z, 9 . 0 enter ...

  • Page 19

    Table 1-4 softkey display prompts softkey display prompts if you press this softkey ... The system will ... Back go back one step in the program display. You can press cursor key (up) or cursor key (down) to scroll forward or backward through a list of programs. Scroll down through the available pro...

  • Page 20

    System number plan/capacities note system type number plan/capacities related pro- gram • external paging (use analog trunk ports) 3 (sl1000) • external moh (use analog trunk ports) 1 (sl1000) • bgm trunk port (use analog trunk ports) 1 (sl1000) trunk ports (total) : 88 (sl1100) • analog trunks 36 (...

  • Page 21

    System number plan/capacities note system type number plan/capacities related pro- gram door boxes 8 (sl1000) 6 (sl1100) 32–02 door box numbers 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) 32–02 dss consoles numbers : • 60 button dss console 12 30–01 operator access number 0 (default) operator extension 15 speed d...

  • Page 22

    System number plan/capacities note system type number plan/capacities related pro- gram rtp ports 0 ~ 65534 rtcp ports 0 ~ 65535 dsp resources 16 passwords programming passwords : level 1 (mf) pcpro/webpro user name : ****** nec-i level 2 (in) pcpro/webpro user name : 12345678 tech level 3 (sa) pcpr...

  • Page 23: Programming

    S ection 1 programming your system the information contained in this chapter provides the information necessary to properly program your system. The programming blocks are organized into the following programming modes. Program number : program name program 10 : system configuration setup on page 2-...

  • Page 24

    Program number : program name program 81 : basic hardware setup for trunk on page 2-438 program 82 : basic hardware setup for extension on page 2-452 program 84 : hardware setup for voip on page 2-470 program 90 : maintenance program on page 2-501 program 92 : copy program on page 2-577 issue 1.0 sl...

  • Page 25: 10-01 : Time And Date

    Program 10 : system configuration setup 10-01 : time and date level sa description use program 10-01 : time and date to change the system time and date through system program- ming. Extension users can also dial service code 828 to change the time if allowed by an extension class of service. Input d...

  • Page 26: 10-02 : Location Setup

    Program 10 : system configuration setup 10-02 : location setup level sa description use program 10-02 : location setup to define the location of the installed system. Input data item no. Item input data default description 01 country code dial (up to four digits) : 0 ~ 9, * , # no setting enter the ...

  • Page 27: 10-03 : Etu Setup

    Program 10 : system configuration setup 10-03 : etu setup level in description use program 10-03 : etu setup to setup and confirm the basic configuration data for each unit. When changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automaticall...

  • Page 28

    For sliu pkg setup (sl1100) physical port number 01 ~ 08 item no. Item input data default 01 logical port number 0 ~ 120 0 03 transmit gain level (s-level) 1 ~ 63 (- 15.5 ~ + 15.5 db) 32 (0 db) 04 receive gain level (r-level) 1 ~ 63 (- 15.5 ~ + 15.5 db) 32 (0 db) 05 select port type 0 = slt 1 = door...

  • Page 29

    Item no. Item input data default note 06 connection bus mode 0 = extended passive bus 1 = short passive bus 0 07 s-point ddi digits 0 ~ 4 0 08 dial sending mode isdn protocol definition 0 = enblock sending 1 = overlap sending 1 09 dial information element isdn protocol definition [only when dialing ...

  • Page 30

    Item no. Item input data default note 05 clip information based on this setting, the system includes a presentation allowed (1) or presentation restricted (0) in the setup message to allow or deny the calling party number. Program 15-01-04 must also be set to 1 if this option is enabled. 0 = no 1 = ...

  • Page 31

    Item no. Item input data default note 21 number of ports 0 = auto 1 = 4 ports 2 = 8 ports 3 = 12 ports 4 = 16 ports 5 = 20 ports 6 = 24 ports 7 = 28 ports 0 for pri (t1) pkg setup physical port number 01 ~ 24 item no. Item input data default 01 logical port number the start port number of a t1 line ...

  • Page 32

    Item no. Item input data default 10 receive input threshold 0 = 0.91/1.70 v 1 = 0.74/0.84 v 2 = 0.59/0.84 v 3 = 0.42/0.45 v 4 = 0.32/0.45 v 5 = 0.21/0.20 v 6 = 0.16/0.10 v 7 = 0.10/not defined 2 for voipdb pkg setup physical port number 01 ~ 16 item no. Item input data default 01 trunk logical port ...

  • Page 33

    Feature cross reference none issue 1.0 sl1000/sl1100 program 10 programming manual 2-11.

  • Page 34

    Program 10 : system configuration setup 10-04 : music on hold setup level in description use program 10-04 : music on hold setup to set the music on hold (moh) source. For internal music on hold, the system can provide a service tone callers on hold or one of eleven synthesized se- lections. Input d...

  • Page 35: 10-06 : Isdn Bri Setup

    Program 10 : system configuration setup 10-06 : isdn bri setup level in description use program 10-06 : isdn bri setup define the te1 selection and did mode for did callers when the bri feature is used. Input data slot no. 01 ~ 16 (sl1000) 01 ~ 09 (sl1100) isdn line no. 01 ~ 04 item no. Item input d...

  • Page 36

    Program 10 : system configuration setup 10-07 : conversation recording resource level in description use program 10-07 : conversation record resource to select the number of conference circuits to be used for conversation recording. Even if this program is set to ‘0', the telephone conversation reco...

  • Page 37: 10-08 : Pre-Ringing Setup

    Program 10 : system configuration setup 10-08 : pre-ringing setup level in description use program 10-08 : pre-ringing setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk led flash...

  • Page 38

    Program 10 : system configuration setup 10-09 : dtmf and dial tone circuit setup level in description use program 10-09 : dtmf and dial tone circuit setup to allocate the circuits on the cpu for ei- ther dtmf receiving or dial tone detection. The cpu has 20 (sl1000) 16 (sl1100) circuits initially, a...

  • Page 39

    Program 10 : system configuration setup 10-12 : cpu network setup level sa description use program 10-12 : cpu network setup to setup the ip address, subnet-mask, and default gate- way addresses. Caution! If any ip address or nic settings are changed, the system must be reset for the changes to take...

  • Page 40

    Item no. Item input data default description 05 nic interface 0 = auto detect 1 = 100mbps, full duplex 2 = 100mbps, half duplex 3 = 10mbps, full duplex 4 = 10mbps, half duplex 0 nic auto ne- gotiate (cpu) 06 network ad- dress port translation (napt) router setup 0 = no (disable) 1 = yes (enable) 0 i...

  • Page 41

    Program 10 : system configuration setup 10-13 : in-dhcp server setup level sa description use program 10-13 : in-dhcp server setup to setup the dhcp server built into the cpu. Input data item no. Item input data default description 01 dhcp server mode 0 = disable 1 = enable 0 enable or disable the u...

  • Page 42

    Program 10 : system configuration setup 10-14 : managed network setup level sa description use program 10-14 : managed network setup to set up the range of the ip address which the dhcp server leases to a client. Input data item no. Item input data default related program 01 the range of the ip addr...

  • Page 43

    Program 10 : system configuration setup 10-15 : client information setup level sa description use program 10-15 : client information setup to set up the client information when the dhcp server needs to assign a fixed ip address to clients. Input data client number 1 ~ 16 item no. Item input data def...

  • Page 44

    Program 10 : system configuration setup 10-16 : option information setup level sa description use program 10-16 : option information setup to set up the option given from the dhcp server to each client. Input data item no. Item input data default 01 router set the router ip address. Code number 0 ~ ...

  • Page 45

    Item no. Item input data default 12 vender class id code number 0 ~ 255 60 (fixed) maximum 256 character strings nec dr700 13 snmp server code number 0 ~ 255 69 (fixed) ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 0.0.0.0 14 pop3 server code number 0 ~...

  • Page 46

    Conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 10 program 10 : system configuration setup 2-24.

  • Page 47

    Program 10 : system configuration setup 10-17 : h.323 gatekeeper setup level sa description use program 10-17 : h.323 gatekeeper setup to set the h.323 gatekeeper information. Input data item name input data default 01 gatekeeper mode set ip address either automatically or manu- ally if using an ext...

  • Page 48

    Program 10 : system configuration setup 10-18 : h.323 alias address setup level sa description use program 10-18 : h.323 alias address setup to set the alias address registered to the outside h.323 gatekeeper. Input data number of alias 1 ~ 6 item name input data default 01 alias address set the tel...

  • Page 49

    Program 10 : system configuration setup 10-19 : voipdb dsp resource selection level in description use program 10-19 : voipdb dsp resource selection to define the criteria for each dsp resource on the voipdb unit. Input data dsp resource number 01 ~ 16 item no. Item input data default 01 voipdb dsp ...

  • Page 50

    Program 10 : system configuration setup 10-20 : lan setup for external equipment level in description use program 10-20 : lan setup for external equipment to define the tcp port/address/etc. For communicating to external equipment. Input data type of external equipment 1 = cti server 5 = smdr output...

  • Page 51

    Program 10 : system configuration setup 10-23 : sip system interconnection setup level sa description use program 10-23 : sip system interconnection setup to determine if the system is intercon- nected and define the ip address of another system, call control port number and alias address for sl1000...

  • Page 52

    Program 10 : system configuration setup 10-24 : daylight savings setup level sa description use program 10-24 : daylight savings setup to set the options for daylight savings. As the tele- phone system is used globally, these settings define when the system should automatically adjust for daylight s...

  • Page 53

    Program 10 : system configuration setup 10-25 : h.323 gateway prefix setup level sa description use program 10-25 : h.323 gateway prefix setup to set the gateway prefix registered to the outside gatekeeper. Input data item no. Item input data default 01 gateway prefix entry 0 = off 1 = on 0 02 gatew...

  • Page 54

    Program 10 : system configuration setup 10-26 : ip system operation setup level in description use program 10-26 : ip system operation setup to enable or disable the peer to peer feature for sip mlt and sip ip stations. Input data item no. Item input data default note 02 rtp forwarding mode 0 = disa...

  • Page 55

    Program 10 : system configuration setup 10-28 : sip system information setup level sa description use program 10-28 : sip system information setup to set up basic sip trunking. Input data item no. Item input data default 01 domain name set the domain name of the sip-url. Up to 64 characters (ex. : u...

  • Page 56

    Program 10 : system configuration setup 10-29 : sip server information setup level sa description use program 10-29 : sip server information setup to define the sip proxy setup for outbound/ inbound. The 10-29 commands are not used in non-registration mode. If entries are made in program 10-29-xx fo...

  • Page 57

    Item no. Item input data default note 13 proxy host name this specifies the host name of the sip server. Up to 48 characters none 14 sip carrier choice this selects the carrier type of the sip server. When carrier a, b, or c is selected in prg10-29-14, prg10-29-16 register sub mode is set "on" autom...

  • Page 58

    Program 10 : system configuration setup 10-30 : sip authentication information setup level in description use program 10-30 : sip authentication information setup to set the authentication options for sip trunks. Input data item no. Item input data default 02 user name this sets the user name of the...

  • Page 59

    Program 10 : system configuration setup 10-33 : sip registrar/proxy information basic setup level in description use program 10-33 : sip registrar/proxy information basic setup to set the registrar/proxy op- tions for sip extensions. Input data item no. Item input data default 01 registration expire...

  • Page 60

    Program 10 : system configuration setup 10-36 : sip trunk registration information setup level in description use program 10-36 : sip trunk registration information setup to set the sip trunk registration in- formation. Input data register id 1 ~ 31 item no. Item input data default 01 registration t...

  • Page 61: 10-37 : Upnp Setup

    Program 10 : system configuration setup 10-37 : upnp setup level in description use program 10-37 : upnp setup to set the upnp (universal plug and play) options for sip trunks. Input data item no. Item input data default 01 upnp mode router must support upnp. 0 = disable 1 = enable 0 02 retry time s...

  • Page 62: 10-39 : Fractional Setup

    Program 10 : system configuration setup 10-39 : fractional setup level in description use program 10-39 : fractional setup to enable or disable the ability to use fractional t1 or pri. Input data item no. Item input data default 01 fractional 0 = disable 1 = enable 0 conditions none feature cross re...

  • Page 63

    Program 10 : system configuration setup 10-40 : ip trunk availability level in description use program 10-40 : ip trunk availability to enable or disable the ability to use sip trunks and as- sign the number of ports if ip trunk is enabled. Input data slot number 0 item no. Item input data default 0...

  • Page 64

    Program 10 : system configuration setup 10-42 : virtual loop back port setting level in description use program 10-42 : virtual loop back port setting to set the data for the virtual loop back port. Input data item no. Item input data default 01 number of loop back ports 0 ~ 30 (0 = no setting) 0 02...

  • Page 65

    Program 10 : system configuration setup 10-45 : ip routing table setup level sa description use program 10-45 : ip routing table setup to set up the ip routing table. Input data routing table number 001 ~ 100 item no. Item input data default 01 network address 0.0.0.0 ~ 126.255.255.254 128.0.0.0 ~ 1...

  • Page 66

    Program 10 : system configuration setup 10-46 : dr700 server information setup level in description use program 10-46 : dr700 server information setup to set up the information of dr700 server. Input data item no. Item input data default related program 01 register mode normal: when the phone boots ...

  • Page 67

    Item no. Item input data default related program 14 nat mode when the system controls the sip multiline terminal via the nat router, this system data is set to on. 0 = off 1 = on 0 conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 10 programming manual 2-45.

  • Page 68

    Program 10 : system configuration setup 10-48 : license activation level in description use program 10-48 : license activation to turn on the license issued from the license server. Input data item no. Item input data default 01 software key code 20-digit character none 02 activation code 8-digit he...

  • Page 69

    Program 10 : system configuration setup 10-49 : license file activation level in description use program 10-49 : license file activation to enable the command to save the license file via cf card which is issued from the license server. Input data item no. Item input data 01 save license file on cf ...

  • Page 70

    Program 10 : system configuration setup 10-50 : license information level in description use program 10-50 : license information to confirm license information that is stored in a system. Input data item no. Item read data 01 license name none 02 license quantity 0 ~ 32767 03 campaign license quanti...

  • Page 71

    Program 10 : system configuration setup 10-51 : pri/t1/e1 selection of pri level in description use program 10-51 : pri/t1/e1 selection of pri to select whether the unit works as pri, t1 or e1. Input data slot number 01 ~ 12 (sl1000) 01 ~ 09 (sl1100) item no. Item input data default 01 pri/t1/e1 sel...

  • Page 72

    Program 10 : system configuration setup 10-52 : free/demo license information level in description use program 10-52 : free/demo license information to display information on free of charge/demo license. Input data item no. Item read data 01 remaining days of free/demo license 0 ~ 9999 conditions no...

  • Page 73

    Program 10 : system configuration setup 10-60 : audio port setup (sl1100) level in description use program 10-60 : audio port setup to defines which audio port on the 084m packages are used for bgm/external moh input data audio port number 1 = bgm 2 = external moh item no. Item input data default 01...

  • Page 74: 10-61 : Relay Port Setup

    Program 10 : system configuration setup 10-61 : relay port setup level in description use program 10-61 : relay port setup to defines the relay port type on the 408m (sl1000) 084m (sl1100). Input data relay port no. 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Item input data default 01 relay type 0 = no ...

  • Page 75: 10-62 : Netbios Setting

    Program 10 : system configuration setup 10-62 : netbios setting level in description use 10-62 : netbios setting to set the data of netbios. Input data item no. Item input data default 01 netbios mode 0 = disabled 1 = enabled 1 02 netbios name maximum 15 characters please avoid using space between t...

  • Page 76

    Program 10 : system configuration setup 10-63 : dhcp client setting level in description use 10-63 : dhcp client setting to set the data of dhcp client. Input data item no. Item input data default 01 dhcp client mode if you are using ip phones/trunks it is recom- mended to not use the dhcp client fu...

  • Page 77: 11-01 : System Numbering

    Program 11 : system numbering 11-01 : system numbering level in description use program 11-01 : system numbering to set the system numbering plan. The numbering plan as- signs the first and second digits dialed and affects the digits an extension user must dial to access other extensions and feature...

  • Page 78

    Dial types dial type description related program 2 extension number 11-02 : extension numbering on page 2-61 11-04 : virtual extension numbering on page 2-62 11-07 : department group pilot numbers on page 2-63 3 trunk access code 11-09-01 : trunk access code 4 special trunk access 11-09-02 : trunk a...

  • Page 79

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 28 0 0 29 0 0 20 0 0 2 * 0 0 2# 0 0 3x 3 2 31 0 0 32...

  • Page 80

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 54 0 0 55 0 0 56 0 0 57 0 0 58 0 0 59 0 0 50 0 0 5 *...

  • Page 81

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 8x 3 1 81 0 0 82 0 0 83 0 0 84 0 0 85 0 0 86 0 0 87 ...

  • Page 82

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 00 0 0 0 * 0 0 0# 0 0 * x 4 4 * 1 0 0 * 2 0 0 * 3 0 ...

  • Page 83

    Program 11 : system numbering 11-02 : extension numbering level in description use program 11-02 : extension numbering to set the extension number. The extension number can have up to eight digits. The first/second digit (s) of the number should be assigned in program 11-01 or program 11-20. This al...

  • Page 84

    Program 11 : system numbering 11-04 : virtual extension numbering level in description use program 11-04 : virtual extension numbering to define the virtual extension numbers. The ex- tension number can have up to four (sl1000) eight (sl1100) digits. The first/second digit (s) of the number should b...

  • Page 85

    Program 11 : system numbering 11-07 : department group pilot numbers level in description use program 11-07 : department group pilot numbers to assign a pilot number to each depart- ment group set up in program 16-02. The pilot number is the number users dial for department call- ing and department ...

  • Page 86

    Program 11 : system numbering 11-09 : trunk access code level in description use program 11-09 : trunk access code to assign the trunk access code. The trunk access code can be set from 1 ~ 8 digits which is defined to type 3 and 4 in program 11-01. This is the code exten- sion users dial to access ...

  • Page 87

    Program 11 : system numbering 11-10 : service code setup (for system administrator) level in description use program 11-10 : service code setup (for system administrator) to customize the service codes for the system administrator. You can customize additional service codes in programs 11-11 ~ 11-16...

  • Page 88

    Item no. Item terminals default related pro- gram note 23 smdr - extension accumu- lated printout code mlt 721 20-07-18 24 smdr - group accumulated printout code mlt 722 20-07-19 25 account code accumulated printout code mlt 723 20-07-20 26 forced trunk disconnect mlt, slt 724 20-07-11 27 trunk port...

  • Page 89

    Conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 11 programming manual 2-67.

  • Page 90

    Program 11 : system numbering 11-11 : service code setup (for setup/entry operation) level in description use program 11-11 : service code setup (for setup/entry operation) to customize the service codes which are used for registration and setup. You can customize additional service codes in pro- gr...

  • Page 91

    Item no. Item terminals default related program note 22 extension name programming mlt 800 15-01 23 second call for did/disa/dil mlt 779 24 change station class of service allows an extension user to change the cos of another extension. Must be allowed in program 20-13-28. Mlt 777 20-13-28 25 automa...

  • Page 92

    Item no. Item terminals default related program note 51 cancel message waiting in- dication slt no setting 52 set/cancel call forward all destination (no split) mlt, slt 791 24-09 53 set/cancel call forward busy destination (no split) mlt, slt 792 24-09 54 set/cancel call forward no answer destinati...

  • Page 93

    Program 11 : system numbering 11-12 : service code setup (for service access) level in description use program 11-12 : service code setup (for service access) to customize the service codes which are used for service access. You can customize additional service codes in programs 11-10, 11-11, and 11...

  • Page 94

    Item no. Item terminals default related program note 22 meet-me answer to external paging mlt, slt 865 23 meet-me answer in same paging group mlt, slt 863 31-02-01 24 combined paging mlt, slt * 1 31-02-01 31-07 25 direct call pickup - own group mlt, slt 856 26 call pickup for specified group mlt, sl...

  • Page 95

    Item no. Item terminals default related program note 58 transfer into conference assign the service code a user dials to transfer a call to a conference call. Mlt, slt 884 59 trunk drop operation for slt slt 760 60 directory dialing mlt 887 (sl1000) 62 security sensor reset service code setting for ...

  • Page 96

    Program 11 : system numbering 11-14 : service code setup (for hotel) level in description use program 11-14 : service code setup (for hotel) to customize the service codes which are used with the hotel/motel feature. You can customize additional service codes in programs 11-10 ~ 11-12, 11-15 and 11-...

  • Page 97

    Feature cross reference • hotel/motel issue 1.0 sl1000/sl1100 program 11 programming manual 2-75.

  • Page 98: Access)

    Program 11 : system numbering 11-15 : service code setup, administrative (for special access) level in description use program 11-15 : service code setup, administrative (for special access) to customize the special access service codes which are used by the administrator in the hotel/motel feature....

  • Page 99

    Program 11 : system numbering 11-16 : single digit service code setup level in description use program 11-16 : single digit service code setup to customize the one-digit service codes used when a busy or ring back signal is heard. You can customize additional service codes in pro- grams 11-10 ~ 11-1...

  • Page 100

    Program 11 : system numbering 11-19 : remote conference pilot number setup level in description use program 11-19 : remote conference pilot number setup to assign the pilot number to be used for the remote conference. This is the number that outside parties will call in order to connect to a confere...

  • Page 101

    Program 11 : system numbering 11-20 : dial extension analyze table level in description use program 11-20 : dial extension analyze table to define the dial type based on three or more digits. This program is relevant only if digits in 11-01-01 are set to 9 (dial extension analyze). Input data dial e...

  • Page 102

    Program 12 : night mode setup 12-01 : night mode function setup level in description use program 12-01 : night mode function setup to set up the night mode options. Refer to the fol- lowing chart for a description of each option, its range and default setting. Input data item no. Item input data def...

  • Page 103

    Program 12 : night mode setup 12-02 : automatic night service patterns level sa description use program 12-02 : automatic night service patterns to define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The dail...

  • Page 104

    Default time pattern 1 set time number start time end time mode 01 0000 0800 2 02 0800 1700 1 03 1700 0000 2 04 0000 0000 1 : : : : 20 0000 0000 1 time pattern 2 set time number start time end time mode 01 0000 0000 2 02 0000 0000 1 : : : : 20 0000 0000 1 time pattern 3 ~ 10 set time number start ti...

  • Page 105

    Program 12 : night mode setup 12-03 : weekly night service switching level sa description use program 12-03 : weekly night service switching to define a weekly schedule of night-switch settings. 21-02 : trunk group routing for extensions input data night mode service group number 01 ~ 04 item no. Da...

  • Page 106

    Program 12 : night mode setup 12-04 : holiday night service switching level sa description use program 12-04 : holiday night service switching to define a yearly schedule of holiday night- switch settings. This schedule is used for the setting of special days when the company is expected to be close...

  • Page 107

    Program 12 : night mode setup 12-05 : night mode group assignment for extensions level in description use program 12-05 : night mode group assignment for extensions to a assign day/night mode group for each extension. Input data extension number up to four digits (sl1000) up to eight digits (sl1100)...

  • Page 108

    Program 12 : night mode setup 12-06 : night mode group assignment for trunks level in description use program 12-06 : night mode group assignment for trunks to assign a day/night mode group for each trunk port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Night mode se...

  • Page 109

    Program 12 : night mode setup 12-07 : text data for night mode level in description use program 12-07 : text data for night mode to make an original text message which is displayed on an lcd of multiline telephone in each mode. Input data night mode service group number 01 ~ 04 day/night mode 1 ~ 8 ...

  • Page 110

    Program 12 : night mode setup 12-08 : night mode service range level sa description use program 12-08 : night mode service range to define the changing range of toggle key for each day/night mode. Input data night mode service group number 01 ~ 04 item no. Range 01 2 ~ 8 (default = 2) example : when...

  • Page 111

    Program 13 : abbreviated dialing 13-01 : speed dialing option setup level in description use program 13-01 : speed dialing option setup to define the speed dialing functions. Input data item no. Item input data default related program 01 speed dialing auto outgo- ing call mode set where the speed di...

  • Page 112

    Program 13 : abbreviated dialing 13-02 : group speed dialing bins level in description use program 13-02 : group speed dialing bins to define the range of bin numbers to be used by each speed dialing group. (refer to 13-03 : speed dialing group assignment for extensions on the next page .) input dat...

  • Page 113

    Program 13 : abbreviated dialing 13-03 : speed dialing group assignment for extensions level in description use program 13-03 : speed dialing group assignment for extensions to assign speed dialing group for each extension. There are 32 available speed dialing groups. Input data extension number up ...

  • Page 114

    Program 13 : abbreviated dialing 13-04 : speed dialing number and name level sb description use program 13-04 : speed dialing number and name to store speed dialing data in the speed dialing areas. This program is also used to define the names assigned to the speed dialing numbers. Input data speed ...

  • Page 115

    Item no. Item input data default related program note 10 memo3 can only be changed in webpro or pcpro. Maximum 28 digit no setting 15-02-58 11 mailbox number 0 ~ 544 0 40-02 12 type 0 = none 1 = work 2 = mobile 3 = voice mail 4 = home 5 = other 0 conditions none feature cross reference • abbreviated...

  • Page 116

    Program 13 : abbreviated dialing 13-05 : speed dial trunk group level sb description use program 13-05 : speed dialing trunk group to define the trunk group to be seized for each speed dialing number. If this program has an entry of 0 (no setting), then seizing a line follows the trunk access group ...

  • Page 117

    Program 13 : abbreviated dialing 13-06 : speed dial number and name level sb description use program 13-06 : speed dial number and name to set up the dial number and name of each speed dial number. Input data extension number up to 4 digits (sl1000) up to 8 digits (sl1100) speed dial number 01 ~ 20 ...

  • Page 118

    Program 13 : abbreviated dialing 13-11 : abbreviated dial group name level sb description use program 13-11 : abbreviated dial group name to set the name of abbreviated dial group name. Input data group number 01 ~ 32 item no. Item input data default 01 group name up to 12 characters 1 = abb : group...

  • Page 119

    Program 14 : trunk, basic setup 14-01 : basic trunk data setup level in description use program 14-01 : basic trunk data setup to set the basic options for each trunk port. Refer to the chart below for a description of each option, its range and default setting. Input data trunk port number 001 ~ 12...

  • Page 120

    Item no. Item input data default related program note 09 private line 0 = disable private line (normal) 1 = enable private line (private line) 0 10 dtmf tones for outgoing calls use this option to enable (1) or disable (0) dtmf tones for out- going trunk calls. 0 = disable (no) 1 = enable (yes) 1 11...

  • Page 121

    Item no. Item input data default related program note 21 caller id block code enter the code, up to 8 digits, that should be used as the caller id block code. This code is au- tomatically inserted before dialed digits if program 14-01-20 is set to 1. Dial (up to eight dig- its) no setting 14-01-20 2...

  • Page 122

    Conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 14 program 14 : trunk, basic setup 2-100

  • Page 123

    Program 14 : trunk, basic setup 14-02 : analog trunk data setup level in description use program 14-02 : analog trunk data setup to set the basic options for each analog trunk port. Refer to the table below for a description of each option, its range and default setting. Input data trunk port number...

  • Page 124

    Item no. Item input data default related pro- gram note 07 dp to dtmf conversion op- tions determine how a user can con- vert a dial pulse (dp) call to a dtmf call. For each trunk, set the type of dp to dtmf conver- sion required. There are three conversion options: automatic (0), automatic and manu...

  • Page 125

    Feature cross reference none issue 1.0 sl1000/sl1100 program 14 programming manual 2-103.

  • Page 126: 14-04 : Behind Pbx Setup

    Program 14 : trunk, basic setup 14-04 : behind pbx setup level in description use program 14-04 : behind pbx setup to indicate if the trunk is installed behind a pbx. There is one item for each mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Day/night mode type of c...

  • Page 127: 14-05 : Trunk Group

    Program 14 : trunk, basic setup 14-05 : trunk group level in description use program 14-05 : trunk group to assign trunks to trunk groups. You can also assign the out- bound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in th...

  • Page 128

    Program 14 : trunk, basic setup 14-06 : trunk group routing level in description use program 14-06 : trunk group routing to set up an outbound routing table for the trunk groups you assigned in program 14-05. When a user dial 9, the system routes their calls in the order (priority) specified. For ex...

  • Page 129

    Feature cross reference none issue 1.0 sl1000/sl1100 program 14 programming manual 2-107.

  • Page 130

    Program 14 : trunk, basic setup 14-07 : trunk access map setup level in description use program 14-07 : trunk access map setup to set up the trunk access maps. This sets an exten- sion access options for trunks. For example, an extension can place only outgoing calls on trunks to which it has outgoi...

  • Page 131

    Access map no. Trunk port no. Default 126 (sl1000) 096 (sl1100) 1 0 (no access) 2 0 (no access) : : 126 (sl1000) 096 (sl1100) 0 (no access) conditions none feature cross reference • central office calls, answering • central office calls, placing issue 1.0 sl1000/sl1100 program 14 programming manual ...

  • Page 132

    Program 14 : trunk, basic setup 14-08 : music on hold source for trunks level in description use program 14-08 : music on hold source for trunks to define a music on hold source for a trunk as coi port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data defau...

  • Page 133

    Program 14 : trunk, basic setup 14-09 : conversation recording destination for trunks level in description use program 14-09 : conversation recording destination for trunks to set the conversation re- cording destination for each trunk. If both programs 14-09 and 15-12 define a destination, the dest...

  • Page 134

    Program 14 : trunk, basic setup 14-11 : id setup for ip trunk level in description use program 14-11 : id setup for ip trunk to set the id of each ip trunk. This program refers to in- coming and outgoing ip trunk calls. The id is sent on an outgoing ip trunk call. This program is used only for h.323...

  • Page 135

    Program 14 : trunk, basic setup 14-12 : sip register id setup for ip trunk level in description use program 14-12 : sip register id setup for ip trunk to define the sip register id for ip trunks. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default 01 r...

  • Page 136

    Program 14 : trunk, basic setup 14-15 : isdn call forward method level in description use program 14-15 : isdn call forward method to assign the activation of call deflection/call re- routing feature. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Input data default rela...

  • Page 137

    Program 14 : trunk, basic setup 14-16 : isdn call transfer method level in description use program 14-16 : isdn call transfer method to assign the method of ect supplementary ser- vice. This mode will control behavior of flash operation at the station which is being grab isdn trunk. Input data trunk...

  • Page 138

    Program 15 : extension, basic setup 15-01 : basic extension data setup level sa description use program 15-01 : basic extension data setup to define the basic settings for each extension. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no. Item input data ...

  • Page 139

    Feature cross reference none issue 1.0 sl1000/sl1100 program 15 programming manual 2-117.

  • Page 140

    Program 15 : extension, basic setup 15-02 : multiline telephone basic data setup level in description use program 15-02 : multiline telephone basic data setup to set up various multiline telephone options. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no...

  • Page 141

    Item no. Item input data default related program note 04 redial (speed dial) control use this option to control the function of the extension redial key when used with speed di- aling. The redial key can ac- cess either the common/ individual or group speed dialing numbers. 0 = common abbreviated di...

  • Page 142

    Item no. Item input data default related program note 15 storage of caller-id for an- swered call 0 = disable (off) 1 = enable (on) 1 16 handsfree operation enable or disable an extension ability to use the speakerphone on outside calls. When dis- abled, users can hear the con- versation, but cannot...

  • Page 143

    Item no. Item input data default related program note 30 toll restriction class select the toll restriction class to use when placing a call from a virtual extension. 0 = vir. Ext. (virtual extension class) 1 = real ext. (real extension class) 1 15-02-21 34 call register mode the caller id scroll st...

  • Page 144

    Item no. Item input data default related program note 50 mute lamp status change 0 = normal 1 = lamp status change 0 54 menu operation mode 0 = automatic close 1 = manual close 0 55 vrs message number 0 ~ 100 0 56 screen saver timer 0 ~ 200 (0 ~ 2000 seconds) 0 (sl1000) 57 caller log on busy 0 = off...

  • Page 145

    Conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 15 programming manual 2-123.

  • Page 146

    Program 15 : extension, basic setup 15-03 : single line telephone basic data setup level in description use program 15-03 : single line telephone basic data setup to set up various single line tele- phone options. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100)...

  • Page 147

    Item no. Item input data default related pro- gram note 09 caller id function - for external module enable (1) or disable (0) the caller id fsk signal for an external caller id module or a 3rd party vendor telephone with caller id display. Important: if voice mail is used, this setting must be disab...

  • Page 148

    Item no. Item input data default related pro- gram note 17 dial tone select when the function of mw has been set from another extension or vm, the dial tone upon off hook is se- lected. 0 = normal 1 = new dt 0 (1) (2) (3) (4) (5) normal reverse reverse reverse normal normal idle idle idle outgoing c...

  • Page 149

    Program 15 : extension, basic setup 15-05 : ip telephone terminal basic data setup level in description use program 15-05 : ip telephone terminal basic data setup to set up the basic settings for an ip telephone. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) ...

  • Page 150

    Item no. Item input data default description related program note 18 ip duplication allowed group 0 = not used 1 = group 1 2 = group 2 3 = group 3 4 = group 4 5 = group 5 6 = group 6 7 = group 7 8 = group 8 9 = group 9 10 = group 10 0 if there is an adapter that has one ip ad- dress coming into it b...

  • Page 151

    Item no. Item input data default description related program note 40 calling name display info via trunk for stan- dard sip 0 = both name and number 1 = name only 2 = number only 3 = none 0 41 time zone(hour) 0 ~ 24 (- 12 ~ + 12 hour) 12 42 time zone(minute) 0 ~ 120 (- 60 ~ + 60 minute) 60 43 video ...

  • Page 152

    Program 15 : extension, basic setup 15-06 : trunk access map for extensions level in description use program 15-06 : trunk access map for extensions to define the trunk access map for each extension. An extension can place only outgoing calls on trunks to which it has outgoing access. Use program 14...

  • Page 153

    Program 15 : extension, basic setup 15-07 : programmable function keys level sa description use program 15-07 : programmable function keys to assign functions to a multiline terminal line keys. For certain functions, you can append data to the key basic function. For example, the function 26 ap- pen...

  • Page 154

    Default programmable keys 1 ~ 8 are trunk line keys (key 1 = trunk line 1, key 2 = trunk line 2, etc.). All other programmable keys are undefined. Function number list table 2-2 function number list [1] normal function code (00 ~ 99, #00 ~ #99) (service code 851 ) func- tion number function addition...

  • Page 155

    Func- tion number function additional data led indication note 22 internal all call pag- ing none 23 privacy release none 24 call pickup for own group none 25 call pickup for an- other group none 26 call pickup for specified group call pickup group number (01 ~ 32) none 27 speed dial - common/privat...

  • Page 156

    Func- tion number function additional data led indication note 52 automatic answer with delay message setup incoming ring group (01 ~ 25) on (red) : setup 53 automatic answer with delay message start on (red) : delay message answering 54 external call for- ward by door box on (red) : setup 55 extens...

  • Page 157

    Func- tion number function additional data led indication note 79 automated atten- dant (in-skin) extension num- ber or pilot num- ber on (red) : setup - all calls slow blink (red) : setup - no answer calls (sl1000) (875msec on/125msec off) : setup – busy calls (sl1000) (125msec on/125msec off/125ms...

  • Page 158

    Table 2-3 function number list [2] appearance function level ( * 00 ~ * 99) (service code 852 ) func- tion number function additional data led indication note * 00 icm key none * 01 trunk key trunk number (001 ~ 126) (sl1000) trunk number (001 ~ 096) (sl1100) fast blink (green) : incoming(own)/ tran...

  • Page 159

    Pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern #7 1 1 1 1 1 1 0 1 0 1 111 2 0 0 4 0 0 6 0 0 ...

  • Page 160

    L e d p a tte rn 0 :[o f f ] l e d p a tte rn 1 :[f l : o n (5 0 0 m s)/off(5 0 0 m s)] o n o ff o n o ff l e d p a tte rn 2 :[w k : o n (2 5 0 m s)/off(2 5 0 m s)] o n o ff l e d p a tte rn 3 :[r w : o n (1 2 5 m s)/off(1 2 5 m s)] o n o ff l e d p a tte rn 4 :[ir : o n (1 2 5 m s)/off(1 2 5 m s)/ ...

  • Page 161

    Program 15 : extension, basic setup 15-08 : incoming virtual extension ring tone setup level in description use program 15-08 : incoming virtual extension ring tone setup to assign a ring tone range (0 ~ 4) to incoming virtual extensions assigned to a virtual extension key (program 15-07). If you en...

  • Page 162

    Program 15 : extension, basic setup 15-09 : virtual extension ring assignment level sa description use program 15-09 : virtual extension ring assignment to assign the ringing options for an exten- sion virtual extension key or virtual extension group answer key which is defined in program 15-07. You...

  • Page 163

    Program 15 : extension, basic setup 15-10 : incoming virtual extension ring tone order setup level sa description use program 15-10 : incoming virtual extension ring tone order setup to set the priority (1 ~ 4) for the virtual extension ring tones set in program 15-08. When virtual extension calls r...

  • Page 164

    Program 15 : extension, basic setup 15-11 : virtual extension delayed ring assignment level sa description use program 15-11 : virtual extension delayed ring assignment to assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in program...

  • Page 165

    Program 15 : extension, basic setup 15-12 : conversation recording destination for extensions level in description use program 15-12 : conversation recording destination for extensions to set the conversation recording destination for each extension. If both programs 14-09 and 15-12 define a destina...

  • Page 166: 15-13 : Loop Keys

    Program 15 : extension, basic setup 15-13 : loop keys level in description use program 15-13 : loop keys to assign the loop key data for each keyset terminal. Loop keys can be incoming, outgoing or both ways. Outgoing loop keys use the entry in item 1. Incoming loop keys use the entry in item 2. Bot...

  • Page 167

    Program 15 : extension, basic setup 15-14 : programmable one-touch keys (sl1100) level sb description use program 15-14 : programmable one-touch keys to define the one-touch key data for each multiline terminal. For each sl1100 wireless telephone to use the transfer when out of range feature, enter ...

  • Page 168

    Program 15 : extension, basic setup 15-16 : sip register id setup for extension level in description use program 15-16 : sip register id setup for extension to define the sip register id for exten- sions. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no....

  • Page 169

    Program 15 : extension, basic setup 15-17 : co message waiting indication level in description use program 15-17 : co message waiting indication to set the message waiting led flash assign- ment on each co line. Input data extension number including virtual extensions up to four digits (sl1000) up t...

  • Page 170

    Program 15 : extension, basic setup 15-18 : virtual extension key enhanced options level in description use program 15-18 : virtual extension key enhanced options to define the operation when a vir- tual extension key is pressed. Input data extension number including virtual extensions up to four di...

  • Page 171

    Program 15 : extension, basic setup 15-22 : mobile extension setup level in description use program 15-22 : mobile extension setup to set the system information for the mobile extension feature. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input da...

  • Page 172

    Program 16 : department group setup 16-01 : department group basic data setup level in description use program 16-01 : department group basic data setup to set the function mode for each depart- ment group. There are 32 available department groups. Input data department group number 1 ~ 32 item no. ...

  • Page 173

    Item no. Item input data default related pro- gram 08 maximum queuing number for de- partment group call to have department group calls queue when busy, set this entry to maximum queuing number. 0 ~ 32 ( 0 = no queuing) 0 09 department hunting no answer time set how long a call rings a depart- ment ...

  • Page 174

    Program 16 : department group setup 16-02 : department group assignment for extensions level in description use program 16-02 : department group assignment for extensions to set the department groups. The system uses these groups (32 department groups) for department calling. Assign pilot numbers to...

  • Page 175

    Program 16 : department group setup 16-03 : secondary department group level in description use program 16-03 : secondary department group to set a second department group for exten- sions. Up to 16 extensions can be assigned per a department group. There are 32 available depart- ment groups. Input ...

  • Page 176

    Program 16 : department group setup 16-04 : call restriction between department groups level in description use program 16-04 : call restriction between department groups to set internal calls between members of different department (station) groups that can be restricted on a per group basis. Each ...

  • Page 177: 20-01 : System Options

    Program 20 : system option setup 20-01 : system options level in description use program 20-01 : system options to set various system options. Input data item no. Item input data default description related pro- gram 01 operator access mode 0 = step call 1 = circular 0 use this program to set up pri...

  • Page 178

    Program 20 : system option setup 20-02 : system options for multiline telephones level in description use program 20-02 : system options for multiline telephones to set various system options for multiline telephones. Input data item no. Item input data default related program note 01 trunk loop key...

  • Page 179

    Item no. Item input data default related program note 07 time and date display mode set how the time and date appear on display telephones. There are eight display modes. 1 ~ 10 (sl1000) type 1 = (12 hour) tue 10 3 : 15 pm (sl1000) type 2 = (12 hour) 3-10 tue 3 : 15 (sl1000) type 3 = (12 hour) 10-3 ...

  • Page 180

    Item no. Item input data default related program note 18 dialing record display time 0 ~ 64800 seconds 30 seconds 19 dss key - virtual exten- sion mode sets the mode of a virtual extension key that ap- pears on a dss console. 0 = no 1 = yes 0 24 lcd scroll mode 0 = character 1 = dot 0 conditions non...

  • Page 181

    Program 20 : system option setup 20-03 : system options for single line telephones level in description use program 20-03 : system options for single line telephones to set up various options for single line telephones. Input data item no. Item input data default related program 01 slt call waiting ...

  • Page 182

    Item no. Item input data default related program 06 headset ringing start time (for slt) define the headset ringing start time. After this time expires from the time when a single line tele- phone is off-hook, the system sets the single line telephone to head- set ringing mode. 0 ~ 64800 seconds 5 2...

  • Page 183

    Program 20 : system option setup 20-04 : system options for virtual extensions level in description use program 20-04 : system options for virtual extensions to set up various system options for virtual extensions. There are 50 available virtual extension ports. Input data item no. Item input data d...

  • Page 184

    Program 20 : system option setup 20-05 : system options for charging cost service level in description use program 20-05 : system options for charging cost service to defines the system options for charging cost service. Input data item no. Item input data default related pro- gram 04 setting of cha...

  • Page 185

    Program 20 : system option setup 20-06 : class of service for extensions level in description use program 20-06 : class of service for extensions to assign a class of service (cos) to an ex- tension. There are 15 classes of service that can be assigned. To specify the options in each class of servic...

  • Page 186

    Program 20 : system option setup 20-07 : class of service options (administrator level) level in description use program 20-07 : class of service options (administrator level) to define the administrator service availability for each extension class of service (cos). Input data class of service numb...

  • Page 187

    Item no. Item input data default related pro- gram note cos 1 ~ 15 15 vrs general message record/ delete turns off or on an extension user ability to dial service code 712 and record, listen to, or erase the general message. 0 = off 1 = on 1 11-10-22 18 smdr printout accumulated extension data 0 = o...

  • Page 188

    Program 20 : system option setup 20-08 : class of service options (outgoing call service) level in description use program 20-08 : class of service options (outgoing call service) to define the outgoing call feature availability for each extension class of service (cos). Input data class of service ...

  • Page 189

    Item no. Item input data default related pro- gram note cos 01 ~ 15 12 department group step calling turns off or on an extension to use department group step calling. 0 = off 1 = on 1 13 isdn clip determines if the isdn call- ing line identity presentation and screening indicators are allowed. 0 = ...

  • Page 190

    Feature cross reference • class of service issue 1.0 sl1000/sl1100 program 20 program 20 : system option setup 2-168.

  • Page 191

    Program 20 : system option setup 20-09 : class of service options (incoming call service) level in description use program 20-09 : class of service options (incoming call service) to define the incoming call feature availability for each extension class of service (cos). Input data class of service ...

  • Page 192

    Item no. Item input data default related pro- gram note cos 01 ~ 15 07 call queuing turn off or on an extension ability to have calls queued if a call rings the extension when it is busy. 0 = off 1 = on 0 20-13-06 09 deny collect call receiving 0 = off 1 = on 0 conditions none feature cross referenc...

  • Page 193

    Program 20 : system option setup 20-10 : class of service options (answer service) level in description use program 20-10 : class of service options (answer service) to define the answer feature avail- ability for each extension class of service (cos). Input data class of service number 01 ~ 15 item...

  • Page 194

    Program 20 : system option setup 20-11 : class of service options (hold/transfer service) level in description use program 20-11 : class of service options (hold/transfer service) to define the hold and transfer feature availability for each extension class of service (cos). Input data class of serv...

  • Page 195

    Item no. Item input data default cos 01 ~ 15 14 trunk-to-trunk transfer restriction turns off or on the trunk-to-trunk transfer restriction. If enabled, trunk-to-trunk trans- fer is not possible. 0 = off 1 = on 0 15 vrs personal greeting (message greet- ing) turns off or on a service code to record,...

  • Page 196

    Feature cross reference • class of service issue 1.0 sl1000/sl1100 program 20 program 20 : system option setup 2-174.

  • Page 197

    Program 20 : system option setup 20-12 : class of service options (charging cost service) level in description use program 20-12 : class of service options (charging cost service) to define the charging cost service availability for each extension service class. Input data class of service number 01...

  • Page 198

    Program 20 : system option setup 20-13 : class of service options (supplementary service) level in description use program 20-13 : class of service options (supplementary service) to define the supplemen- tary feature availability for each extension class of service (cos). Input data class of servic...

  • Page 199

    Item no. Item input data default related program cos 01 ~ 15 13 continued dialing (dtmf) signal on icm call turn off or on an extension user ability to use continued dialing, which allows dtmf signal sending while talking on ex- tension. 0 = off 1 = on 1 14 department calling (plt no called ex- tens...

  • Page 200

    Item no. Item input data default related program cos 01 ~ 15 28 allow class of service to be changed turns off or on the ability of an extension class of service to be changed via ser- vice code 777. 0 = off 1 = on 0 29 paging display turns off or on an extension user ability to display paging infor...

  • Page 201

    Item no. Item input data default related program cos 01 ~ 15 49 blf indication on co incoming state determine if a blf of the station will light when a normal co call is ringing the phone. 0 = off 1 = on 0 51 number and name appear in the direc- tory determine if an extension name and number will be...

  • Page 202

    Program 20 : system option setup 20-14 : class of service options for disa/e&m level in description use program 20-14 : class of service options for disa/e&m to enable/disable disa and tie line class of service options. You assign a disa class of service to disa users in program 25-09. Assign tie li...

  • Page 203

    Item no. Item input data default cos 01 ~ 15 10 call forward setting by remote via disa enable or disable a disa caller ability to use the call forward service codes (programs 11-11-01 ~ 11-11-05). 0 = off 1 = on 0 11 disa/tie trunk barge-in this option enables or disables a disa or tie trunk caller...

  • Page 204: 20-15 : Ring Cycle Setup

    Program 20 : system option setup 20-15 : ring cycle setup level in description use program 20-15 : ring cycle setup to define the ringing cycles for each ring type. Input data item no. Incoming signal type ringing cycle default 01 normal incoming call on trunk 1 ~ 13 3 02 pbx, ces incoming call 8 03...

  • Page 205

    Feature cross reference none issue 1.0 sl1000/sl1100 program 20 programming manual 2-183.

  • Page 206

    Program 20 : system option setup 20-16 : selectable display messages level sa description use program 20-16 : selectable display messages to enter the selectable display messages. There are 20 alphanumeric messages, with up to 16 (sl1000) 48 (sl1100) characters. Use the follow- ing chart when progra...

  • Page 207

    Number message 7 business trip back ## / ## 8 business trip ########## 9 gone for the day 10 on vacation until ## / ## 11 message 11 12 message 12 13 message 13 14 message 14 15 message 15 16 message 16 17 message 17 18 message 18 19 message 19 20 message 20 conditions • time value ## : ## must be f...

  • Page 208

    Program 20 : system option setup 20-17 : operator extension level in description use program 20-17 : operator extension to designate an operator. When an extension user dials 0 (defined by program 11-01 type 5), calls go to the operator selected in this program. If you do not assign an extension in ...

  • Page 209

    Program 20 : system option setup 20-18 : service tone timers level in description use program 20-18 : service tone timers to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Input data item no. Item input...

  • Page 210

    Program 20 : system option setup 20-19 : system options for caller id level in description use program 20-19 : system options for caller id to define the system options for the caller id fea- ture. Input data item no. Item input data default note 01 caller id displaying format (if displaying digits ...

  • Page 211

    Program 20 : system option setup 20-20 : message setup for non-caller id data level in description use program 20-20 : message setup for non-caller id data to define the messages which are dis- played when no caller id information is received. Input data item no. Item input data default 01 private c...

  • Page 212

    Program 20 : system option setup 20-21 : system options for long conversation level in description use program 20-21 : system options for long conversation to define the system options for the long conversation feature. Input data item no. Item input data default related program 01 long conversation...

  • Page 213

    Program 20 : system option setup 20-23 : system options for cti level in description use program 20-23 : system options for cti to define the system options for the cti feature. Input data item no. Item input data default 01 delayed ring timer for cti 0 ~ 64800 seconds 30 second 02 alert replay time...

  • Page 214: 20-25 : Isdn Options

    Program 20 : system option setup 20-25 : isdn options level in description use program 20-25 : isdn options to define the isdn system options. Input data item no. Item input data default 01 send the release message after sub- scriber hangs up 0 = service off 1 = service on 1 02 progress indicate inf...

  • Page 215

    Feature cross reference • isdn compatibility issue 1.0 sl1000/sl1100 program 20 programming manual 2-193.

  • Page 216

    Program 20 : system option setup 20-26 : multiplier for charging cost level in description use program 20-26 : multiplier for charging cost to define the multiplier for charging cost to each extension service class. Input data service class 01 ~ 15 item no. Item input data default 01 value (%) 100 ~...

  • Page 217

    Program 20 : system option setup 20-28 : trunk to trunk conversation level in description use program 20-28 : trunk to trunk conversation to define system options for trunk to trunk con- versation. Input data item no. Item input data default related program- ming 01 conversation continue code input ...

  • Page 218

    Program 20 : system option setup 20-29 : timer class for extension level in description use program 20-29 : timer class for extension to assign the timer class to each extension. There are 16 classes that can be assigned. You make eight entries for this program, one for each night ser- vice mode. Th...

  • Page 219

    Program 20 : system option setup 20-30 : timer class for trunks level in description use program 20-30 : timer class for trunks to assign the timer class to each trunk. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. The details of...

  • Page 220

    Program 20 : system option setup 20-31 : timer class timer assignment level in description use program 20-31 : timer class timer assignment to assign values to the timers on a class of service basis. Input data timer class number 0 ~ 15 item no. Item input data default related program 01 trunk queui...

  • Page 221

    Item no. Item input data default related program 09 did ring-no-answer time in systems with did ring-no-answer intercept, this time sets the ring-no- answer time. This time is how long a did call rings the destination exten- sion before rerouting to the intercept ring group. 0 ~ 64800 seconds 20 sec...

  • Page 222

    Item no. Item input data default related program 20 long conversation disconnect (trunk to trunk) this time determines how long the system waits before disconnecting a disa caller or any trunk-to-trunk (such as tandem trunking) conversa- tion call after the long conversation tone is heard. 0 ~ 64800...

  • Page 223

    Program 20 : system option setup 20-34 : remote conference group setup level sa description use program 20-34 : remote conference group setup to define the remote conference options. Input data remote conference group number 1 ~ 4 item no. Item input data default 01 conference name enter the name di...

  • Page 224

    Program 20 : system option setup 20-35 : extension's operator setting level in description use program 20-35 : extension’s operator setting to assign an extension to an operator group. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input data default...

  • Page 225

    Program 20 : system option setup 20-36 : trunk's operator setting level in description use program 20-36 : trunk’s operator setting to assign a trunk to an operator group. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default 01 trunk’s operator setting ...

  • Page 226

    Program 20 : system option setup 20-37 : operator extension group setup level in description use program 20-37 : operator extension group setup to define the operator(s) in the operator group. Input data operator group 1 ~ 15 operator number 1 ~ 8 item no. Item input data default 01 operator extensi...

  • Page 227

    Program 20 : system option setup 20-38 : operator group setting level in description use program 20-38 : operator group setting to set up priority of a call when calling an operator telephone. Input data operator group 1 ~ 15 item no. Item input data default 01 operator access mode assign if the ope...

  • Page 228

    Program 20 : system option setup 20-39 : shortcut operation setup (sl1000) level in description use program 20-39 : shortcut operation setup to defines the function for shortcut operation. Input data operator group 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , # item no. Item input data 01 shortcut operation 00...

  • Page 229

    Program 20 : system option setup 20-40 : function key list setup (sl1000) level in description use program 20-40 : function key list setup to defines the function list used with function key set- ting. Input data data no. 1 ~ 10 item no. Item input data 01 function key list 00 ~ 99, * 00 ~ * 99 (fun...

  • Page 230

    Program 20 : system option setup 20-41 : service code setup (sl1000) level in description use program 20-41 : service code setup to set up feature key from dial key. Input data dial 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , # item no. Item input data 01 service code setup 0 = none 1 = call forward - all 2 =...

  • Page 231

    Program 20 : system option setup 20-42 : night mode for each package level in description use program 20-42 : night mode for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 16 (sl1000) 02 ~ 09 (sl1100) item no. It...

  • Page 232

    Program 20 : system option setup 20-43 : power supply for each package level in description use program 20-43 : power supply for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 16 (sl1000) 02 ~ 09 (sl1100) operati...

  • Page 233: 20-44 : Watch Mode Setup

    Program 20 : system option setup 20-44 : watch mode setup level in description use program 20-44 : watch mode setup to defines the watch mode. Input data item no. Item input data default 01 internal paging group for watch message define internal paging group number for watching message. 0 ~ 32 0 02 ...

  • Page 234

    Program 20 : system option setup 20-45 : remote watch setup level in description use program 20-45 : remote watch setup to defines the remote watch. Input data terminal number 1 ~ 6 item no. Item input data default 01 ring terminal for remote inspection extension number for remote inspection extensi...

  • Page 235

    Program 20 : system option setup 20-46 : security sensor setup level in description use program 20-46 : security sensor setup to defines the security sensor. Input data security sensor number 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Item input data default 01 sensor mode define door port (408m 6, 7 (s...

  • Page 236

    Program 20 : system option setup 20-47 : time pattern setting for watch mode level in description use program 20-47 : time pattern setting for watch mode to defines the watch mode time pattern. Input data time pattern 01 ~ 08 item no. Item input data default 01 watch mode time pattern define watch m...

  • Page 237

    Program 20 : system option setup 20-48 : time pattern setting for security sensor level in description use program 20-48 : time pattern setting for security sensor to defines the security sensor time pattern. Input data time pattern 01 ~ 08 item no. Item input data default 01 security sensor time pa...

  • Page 238

    Program 20 : system option setup 20-49 : caller id shared group basic data setup level in description use program 20-49 : caller id shared group basic data setup to defines the function mode for each caller id shared group. Input data caller id shared group number 01 ~ 08 item no. Item input data re...

  • Page 239

    Program 21 : outgoing call setup 21-01 : system options for outgoing calls level in description use program 21-01 : system options for outgoing calls to set the system options for outgoing call service. Input data item no. Item input data default related program 01 seizure trunk line mode select the...

  • Page 240

    Item no. Item input data default related program 10 dial digits for toll restriction path if this option is programmed with an entry other than 0, a call does not have a talk path unless the user dials at least the number of digits entered in this option when placing an outgoing call. This means tha...

  • Page 241

    Item no. Item input data default related program 19 do-not-call-setup 0 = no service 1 = extented common re- striction 0 15-01-07 conditions none feature cross reference • central office calls, placing issue 1.0 sl1000/sl1100 program 21 programming manual 2-219.

  • Page 242

    Program 21 : outgoing call setup 21-02 : trunk group routing for extensions level in description use program 21-02 : trunk group routing for extensions to assign program 14-06 routes to ex- tensions. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no. Day/...

  • Page 243

    Program 21 : outgoing call setup 21-03 : trunk group routing for trunks level in description use program 21-03 : trunk group routing for trunks to set the trunk route table for automatic external call forward. The route table is set in program 14-06. Input data trunk port number 001 ~ 126 (sl1000) 0...

  • Page 244

    Program 21 : outgoing call setup 21-04 : toll restriction class for extensions level in description use program 21-04 : toll restriction class for extensions to assign a toll restriction class to an extension. The details of toll restriction are defined in program 21-05 and 21-06. A telephone and a ...

  • Page 245

    Program 21 : outgoing call setup 21-05 : toll restriction class level in description use program 21-05 : toll restriction class to set the system toll restriction classes (1 ~ 15). Input data toll restriction class number 1 ~ 15 item no. Item input data default related program note 01 international ...

  • Page 246

    Item no. Item input data default related program note 11 intercom call restriction determines if incoming and outgoing intercom calls are allowed. 0 = disable (no) 1 = enable (yes) 0 12 pbx call restriction use this option to set how the system toll restricts calls over pbx trunks. If you enable pbx...

  • Page 247

    Program 21 : outgoing call setup 21-06 : toll restriction table data setup level in description use program 21-06 : toll restriction table data setup to set the system toll restriction data. Dial 1 ~ 9, 0, * , # can be entered in each table. Input data item no. Item table input data default 01 inter...

  • Page 248

    Item no. Item table input data default 08 pbx access code use this option to enter the pbx access code. When the system is behind a pbx, this is the code users dial to access a pbx trunk. Toll restriction begins after the pbx ac- cess code. For pbx trunks (program 14-04) the sys- tem only toll restr...

  • Page 249

    Program 21 : outgoing call setup 21-07 : toll restriction override password setup level sa description use program 21-07 : toll restriction override password setup to assign toll restriction override codes to extension ports. Each code must have four digits, using any combination of 0 ~ 9, # and * ....

  • Page 250

    Program 21 : outgoing call setup 21-08 : repeat dial setup level in description use program 21-08 : repeat dial setup to define the automatic repeat dial data. Input data item no. Item input data default 01 repeat redial count sets how many times a repeat redial auto- matically repeats if the call d...

  • Page 251: 21-09 : Dial Block Setup

    Program 21 : outgoing call setup 21-09 : dial block setup level in description use program 21-09 : dial block setup to define the dial blocking toll restriction class and dial block password to be used by the supervisor extension. Input data item no. Item input data default 01 toll restriction class...

  • Page 252

    Program 21 : outgoing call setup 21-10 : dial block restriction class per extension level in description use program 21-10 : dial block restriction class per extension to define the toll restriction class to each extension when the extension is set for dial block restriction. If this data is 0, toll...

  • Page 253

    Program 21 : outgoing call setup 21-11 : extension ringdown (hotline) assignment level in description use program 21-11 : extension ringdown (hotline) assignment to define the hotline destination number for each extension number. Input data extension number maximum four digits (sl1000) maximum eight...

  • Page 254

    Program 21 : outgoing call setup 21-12 : isdn calling party number setup for trunks level in description use program 21-12 : isdn calling party number setup for trunks to assign calling party num- bers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not h...

  • Page 255

    Program 21 : outgoing call setup 21-13 : isdn calling party number setup for extensions level in description use program 21-13 : isdn calling party number setup for extensions to assign each extension a calling party number (maximum 16 digits per entry). The calling number is the subscriber number o...

  • Page 256

    Program 21 : outgoing call setup 21-14 : walking toll restriction password setup level sa description use program 21-14 : walking toll restriction password setup to assign the password and toll re- striction class for walking toll restriction. Each code has six digits, using any combination of 0 ~ 9...

  • Page 257

    Program 21 : outgoing call setup 21-15 : individual trunk group routing for extensions level in description use program 21-15 : individual trunk group routing for extensions to designate the alternate trunk access route accessed when a user dials the alternate trunk route access code. Refer to pro- ...

  • Page 258

    Program 21 : outgoing call setup 21-17 : ip trunk (sip) calling party number setup for trunk level in description use program 21-17 : ip trunk (sip) calling party number setup for trunk set the sip calling party number for individual trunks. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 ...

  • Page 259: Extension

    Program 21 : outgoing call setup 21-18 : ip trunk (h.323) calling party number setup for extension level in description use program 21-18 : ip trunk (h.323) calling party number setup for extension to assign the calling party number for each extension. The assigned number is sent to the exchange whe...

  • Page 260: Extension

    Program 21 : outgoing call setup 21-19 : ip trunk (sip) calling party number setup for extension level in description use program 21-19 : ip trunk (sip) calling party number setup for extension to set the sip call- ing party number for an individual extension. Input data extension number up to four ...

  • Page 261

    Program 21 : outgoing call setup 21-20 : sip trunk call discernment setup for extension level sb description use program 21-20 : sip trunk call discernment setup for extension to set the sip trunk call discernment. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) it...

  • Page 262: Setting)

    Program 21 : outgoing call setup 21-21 : toll restriction for trunks (seized trunk basis setting) level in description use program 21-21 : toll restriction for trunks (seized trunk basis setting) to define the toll re- striction class to each trunk. The details of toll restriction are defined by pro...

  • Page 263

    Program 21 : outgoing call setup 21-22 : co message waiting indication - call back settings level in description use program 21-22 : co message waiting indication - call back settings to define the settings of co message waiting indication. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (...

  • Page 264

    Program 21 : outgoing call setup 21-24 : forced access dial data level in description use program 21-24 : forced access dial data to set for emergency number data. First digit of dial- ing data should be same as trunk access code. Input data item no. Item input data default 01 define the emergency n...

  • Page 265

    Program 22 : incoming call setup 22-01 : system options for incoming calls level in description use program 22-01 : system options for incoming calls to define the system options for incoming calls. Input data item no. Item input data default related program 01 incoming call priority use this option...

  • Page 266

    Item no. Item input data default related program 12 mobile extension answer time 0~ 64800 seconds 3 seconds 15-22-04 conditions none feature cross reference • central office calls, answering issue 1.0 sl1000/sl1100 program 22 program 22 : incoming call setup 2-244.

  • Page 267

    Program 22 : incoming call setup 22-02 : incoming call trunk setup level in description use program 22-02 : incoming call trunk setup to assign the incoming trunk type for each trunk. There is one item for each night service mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) it...

  • Page 268

    Program 22 : incoming call setup 22-03 : trunk ring tone range level in description use program 22-03 : trunk ring tone range to select the ring tone range for the trunk. The trunk uses a ring tone in the range selected when it rings an extension. Eight ring tones are available. Cus- tomize the trun...

  • Page 269

    Incoming signal frequency pattern type frequency 1 frequency 2 modulation pattern 3 high middle low 2000 1400 1100 760 660 540 16hz 16hz 16hz pattern 4 high middle low 2000 1400 1100 760 660 540 8hz 8hz 8hz conditions none feature cross reference • selectable ring tones issue 1.0 sl1000/sl1100 progr...

  • Page 270

    Program 22 : incoming call setup 22-04 : incoming extension ring group assignment level sa description use program 22-04 : incoming extension ring group assignment to assign extensions to ring groups. Calls ring extensions according to ring group programming. Use program 22-05 to assign trunks to ri...

  • Page 271

    Program 22 : incoming call setup 22-05 : incoming trunk ring group assignment level in description use program 22-05 : incoming trunk ring group assignment to assign trunks to incoming ring groups. There are 25 available ring groups. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100)...

  • Page 272

    Program 22 : incoming call setup 22-06 : normal incoming ring mode level in description use program 22-06 : normal incoming ring mode to define whether or not an extension should ring for the normal incoming ring mode. Input data extension number maximum four digits (sl1000) maximum eight digits (sl...

  • Page 273: 22-07 : Dil Assignment

    Program 22 : incoming call setup 22-07 : dil assignment level in description use program 22-07 : dil assignment to assign the destination extension or department calling group for each dil incoming trunk. A dil rings an extension directly, without any other access map or ring group programming. If a...

  • Page 274

    Program 22 : incoming call setup 22-08 : dil/irg no answer destination level in description for dil delayed ringing, use program 22-08 : dil/irg no answer destination to assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time expires (pro- gram 22-01-04)....

  • Page 275

    Program 22 : incoming call setup 22-09 : did basic data setup level in description use program 22-09 : did basic data setup to define the basic setting of dial-in incoming calls for each trunk group. Input data trunk group number 01 ~ 25 item no. Item input data default 01 expected number of digits ...

  • Page 276

    Program 22 : incoming call setup 22-10 : did translation table setup level in description use program 22-10 : did translation table setup to specify the size of the did translation tables. There are 2000 translation table entries that you can allocate among 20 translation tables. Input data conversi...

  • Page 277

    Program 22 : incoming call setup 22-11 : did translation number conversion level sa description use program 22-11 : did translation number conversion to specify for each translation table entry (800). • the digits received by the system (eight maximum) • the extension the system dials after translat...

  • Page 278

    Item no. Input data description default 02 target number enter the destination number to which the did number is sent. Maximum 36 digits (0 ~ 9, * , #, @) see default value 03 did name this is the name that is assigned to the did digits when it rings the ex- tension. Maximum 12 characters no setting...

  • Page 279

    Conversion table received number target number : : : 100 99 299 : : : 800 no setting no setting conditions when the trunk type is set to 3 (did) in 22-02-01, the did transfer destination for each did feature is not supported. This feature is supported only for did trunks when assigned as vrs. Featur...

  • Page 280

    Program 22 : incoming call setup 22-12 : did intercept ring group level in description for each did translation table, use program 22-12 : did intercept ring group to define the first destination group for did calls. Depending on the entry in programs 22-09-02 and 22-11-04, the incoming calls route ...

  • Page 281

    Program 22 : incoming call setup 22-13 : did trunk group to translation table assignment level in description use program 22-13 : did trunk group to translation table assignment to assign the did trunk groups to did translation tables. Did trunks should be in their own group. If you have more than o...

  • Page 282

    Program 22 : incoming call setup 22-14 : vrs delayed message for irg level in description use program 22-14 : vrs delayed message for irg (incoming group ring) to define for each in- coming ring group the timers, vrs message number and type of tone for vrs waiting message. Input data incoming ring g...

  • Page 283

    Program 22 : incoming call setup 22-15 : vrs delayed message for department group level in description use program 22-15 : vrs delayed message for department group to define for each department (extension) group the timers, vrs message number and tone kind for vrs delayed message. There are 32 avail...

  • Page 284

    Program 22 : incoming call setup 22-16 : private call refuse target area setup level in description use program 22-16 : private call refuse target area setup to define speed dial group number for private call refuse. Input data item no. Item input data default 01 speed dial group number 0 ~ 32 0 con...

  • Page 285: Pattern

    Program 22 : incoming call setup 22-17 : dial-in conversion table area setup for time pattern level sa description use program 22-17: dial-in conversion table area setup for time pattern to define time zone and dial-in conversion table (program 22-11) for time pattern. Input data conversion table nu...

  • Page 286

    Program 22 : incoming call setup 22-18 : private call assignment setup level in description use program 22-18: private call assignment setup to define assignment and incoming ring pattern for private calls. Input data item no. Item input data default related program 01 transfer mode 0 = not defined ...

  • Page 287

    Program 22 : incoming call setup 22-19 : did mfc dialing options level in description use program 22-19 : did mfc dialing options to define the mfc dialing for each did table entry. This option is used for latin america only. Input data conversion table number 1 ~ 800 item no. Item input data defaul...

  • Page 288

    Program 22 : incoming call setup 22-20 : flexible ringing by caller id setup level in description use program 22-20: flexible ringing by caller id setup to set flexible ringing by caller id per timer pattern mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) day/night mode 01 ~...

  • Page 289

    Program 23 : answer features setup 23-02 : call pickup groups level in description use program 23-02 : call pickup groups to assign extensions to call pickup groups. This program also lets you assign an extension call pickup group priority. If two extensions in a group are ringing at the same time, ...

  • Page 290

    Program 23 : answer features setup 23-03 : universal answer/auto answer level in description use program 23-03 : universal answer/auto answer to assign trunk routes (set in program 14-06) to extensions for universal answer. If the call ringing the paging system is in an extension assigned route, the...

  • Page 291

    Program 23 : answer features setup 23-04 : ringing line preference for virtual extensions level in description use program 23-04 : ringing line preference for virtual extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. There are 50 avai...

  • Page 292

    Program 24 : hold/transfer setup 24-01 : system options for hold level in description use program 24-01 : system options for hold to define the system options for the hold feature. Input data item no. Item input data default related program 01 hold recall time a call on hold recalls the extension th...

  • Page 293

    Program 24 : hold/transfer setup 24-02 : system options for transfer level in description use program 24-02 : system options for transfer to define the system options for the transfer fea- ture. Input data item no. Item input data default related pro- gram 01 busy transfer use this option to prevent...

  • Page 294

    Item no. Item input data default related pro- gram 12 no answer trunk-to-trunk transfer 0 ~ 64800 seconds 0 14-01-26 13 hook flash sending timer when the sys- tem answers automatically time before sending the hook flash for call forward centrex. 0 ~ 64800 seconds 2 seconds conditions none feature cr...

  • Page 295: 24-03 : Park Group

    Program 24 : hold/transfer setup 24-03 : park group level in description use program 24-03 : park group to assign an extension to a park group. The system allows a total of 64 park groups. An extension user can pick up only a call parked in orbit by an extension user in own group. Input data extensi...

  • Page 296

    Program 24 : hold/transfer setup 24-04 : automatic trunk-to-trunk transfer target setup level in description use program 24-04 : automatic trunk-to-trunk transfer target setup to assign the speed dialing number bin which should be used as the destination of the automatic trunk-to-trunk transfer. Inp...

  • Page 297

    Program 24 : hold/transfer setup 24-05 : department group transfer target setup level in description use program 24-05 : department group transfer target setup to assign the speed dialing bin which is used as the destination of the extension for the extension group. There are 32 available department...

  • Page 298

    Program 24 : hold/transfer setup 24-09 : call forward split settings level in description use program 24-09 : call forward split settings to assign call forwarding type and the destination number for each extension/virtual extension. The destination can have up to 24 digits, using 0 ~ 9, * , #, and ...

  • Page 299

    Feature cross reference • call forwarding, off-premise issue 1.0 sl1000/sl1100 program 24 programming manual 2-277.

  • Page 300

    Program 25 : vrs/disa setup 25-01 : vrs/disa line basic data setup level in description use program 25-01 : vrs/disa line basic data setup to define the basic setting of each vrs/ disa line. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default related p...

  • Page 301

    Program 25 : vrs/disa setup 25-02 : did/disa vrs message level in description use program 25-02 : did/disa vrs message to assign the vrs message number to be used as the automated attendant message for each trunk which is assigned as a vrs/disa. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ ...

  • Page 302: Dialing

    Program 25 : vrs/disa setup 25-03 : vrs/disa transfer ring group with incorrect dialing level in description use program 25-03 : vrs/disa transfer ring group with incorrect dialing to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial. ...

  • Page 303: Answer/busy

    Program 25 : vrs/disa setup 25-04 : vrs/disa transfer ring group with no answer/busy level in description use program 25-04 : vrs/disa transfer ring group with no answer/busy to set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant caller ...

  • Page 304

    Program 25 : vrs/disa setup 25-05 : vrs/disa error message assignment level in description use program 25-05 : vrs/disa error message assignment to assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message (...

  • Page 305

    Program 25 : vrs/disa setup 25-06 : vrs/disa one-digit code attendant setup level in description use program 25-06 : vrs/disa one-digit code attendant setup to set up single digit dialing through the vrs. This gives vrs callers single key access to extensions, the company operator, de- partment call...

  • Page 306

    Program 25 : vrs/disa setup 25-07 : system timers for vrs/disa level in description use program 25-07 : system timers for vrs/disa to set the value for the system timers which af- fect did and disa. Refer to the following chart for a description of each option, its range and default setting. Input d...

  • Page 307

    Item no. Item input data default related pro- gram 11 vrs/disa answer delay time sets up the time the system waits after receiv- ing an incoming vrs/disa call before the sys- tem automatically answers the call. 0 ~ 64800 seconds 0 second 13 vrs/disa busy tone interval if a disa caller dials a busy e...

  • Page 308

    Program 25 : vrs/disa setup 25-08 : disa user id setup level sa description use program 25-08 : disa user id setup to set the 6-digit disa password for each user. There are 15 users each with one 6-digit password. Input data disa user number 01 ~ 15 item no. Password default 01 dial (fixed - six dig...

  • Page 309

    Program 25 : vrs/disa setup 25-09 : class of service for disa users level in description use program 25-09 : class of service for disa users to set the disa class of service for each user. When a disa caller enters a password (defined in program 25-08), the system identifies the user and associates ...

  • Page 310

    Program 25 : vrs/disa setup 25-10 : trunk group routing for disa level in description use program 25-10 : trunk group routing for disa to assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. En- able or disable the di...

  • Page 311

    Program 25 : vrs/disa setup 25-11 : disa toll restriction class level in description for systems that use toll restriction, use program 25-11 : disa toll restriction class to assign a toll restriction class (1-15) to each disa user (1~15). The system uses the toll restriction class you enter in prog...

  • Page 312

    Program 25 : vrs/disa setup 25-12 : alternate trunk group routing for disa level in description use program 25-12 : alternate trunk group routing for disa to define the trunk route selected when a disa caller dials the alternate trunk access code. The route selected is based on the disa caller class...

  • Page 313

    Program 25 : vrs/disa setup 25-13 : system option for disa level in description use program 25-13 : system option for disa to enter the password disa callers must dial before the system allows them to record, listen to and or erase the vrs messages. This program also is used to define additional dis...

  • Page 314

    Program 25 : vrs/disa setup 25-15 : disa transfer target setup level in description use program 25-15 : disa transfer target setup to assign a speed dial number when a dial tone times-out, or when the wrong number is received and the target extension does not answer or is busy. Input data trunk port...

  • Page 315: Routing

    Program 26 : ars service & least cost routing 26-01 : automatic route selection (ars/f-route) service level in description use program 26-01 : automatic route selection service (ars/f-route) to define the system op- tions for automatic route selection (ars/f-route). Input data item no. Item input da...

  • Page 316: Routing

    Program 26 : ars service & least cost routing 26-02 : dial analysis table for ars/lcr level in description use program 26-02 : dial analysis table for ars/lcr to set pre-transaction tables for selecting automatic route selection (ars/f-route). • service type 1 (route to trunk group number) - the num...

  • Page 317: Routing

    Program 26 : ars service & least cost routing 26-03 : ars dial treatments level in description use program 26-03 : ars dial treatments to assign the 15 dial treatments for automatic ars dial- ing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial tre...

  • Page 318: Routing

    Program 26 : ars service & least cost routing 26-04 : ars class of service level in description use program 26-04 : ars class of service to set the ars class of service for an extension. Auto- matic route selection (ars/f-route) uses ars class of service when determining how to route ex- tension cal...

  • Page 319: Routing

    Program 26 : ars service & least cost routing 26-05 : lcr carrier table level in description use program 26-05 : lcr carrier table to define the lcr access codes and routing options. These options include authorization codes and cost center input data item no. Item input data default 01 delete digit...

  • Page 320: Routing

    Program 26 : ars service & least cost routing 26-06 : lcr authorization code table level in description use program 26-06 : lcr authorization code table to define the optional authorization code (or pin code) required by the indirect carrier. The authorization code is inserted if set in program 26-0...

  • Page 321: Routing

    Program 26 : ars service & least cost routing 26-07 : lcr cost center code table level in description use program 26-07 : lcr cost center code table to define the optional cost center code required by the indirect carrier. The cost center code is set for each extension. The cost center code is inser...

  • Page 322: Routing

    Program 26 : ars service & least cost routing 26-08 : lcr manual override access code table level in description use program 26-08 : lcr manual override access code table to define the access codes that the users can dial to select an indirect carrier i.E. Bypass the automatic selection of program 2...

  • Page 323: Routing

    Program 26 : ars service & least cost routing 26-09 : lcr manual override exemption table level in description use program 26-09 : lcr manual override exemption table to define the numbers that must not be sent via an indirect carrier when the user dials a manual override access code. The exemptions...

  • Page 324: Routing

    Program 26 : ars service & least cost routing 26-11 : transit network id table level in description use program 26-11 : transit network id table to define transit network id for alternate carrier ac- cess, which is referred from program 26-03. Input data transit network id table 1 ~ 4 item no. Item ...

  • Page 325: Routing

    Program 26 : ars service & least cost routing 26-12 : network specific parameter table for ars level in description use program 26-12 : network specific parameter table for ars to define the network specific pa- rameter table. Input data network specific parameter table 1 ~ 16 item no. Item input da...

  • Page 326

    Program 30 : dss/dls console setup 30-01 : dss console operating mode level in description use program 30-01 : dss console operating mode to set the mode of the system dss consoles. The entry for this option applies to all the system dss consoles. The available options are: • regular (business) mode...

  • Page 327

    Program 30 : dss/dls console setup 30-02 : dss console extension assignment level in description use program 30-02 : dss console extension assignment to identify which extensions have dss consoles connected. • up to 12 different extensions with dss consoles can be set up. A single extension can have...

  • Page 328

    Program 30 : dss/dls console setup 30-03 : dss console key assignment level sa description use program 30-03 : dss console key assignment to customize the key assignments for 60- button dss consoles. A dss console key can have any function with up to four digits (sl1000) up to eight digits (sl1100) ...

  • Page 329

    Function number function additional data led indication note 07 conference key on (red) : conference operation 08 incoming call id list fast blink (red) : existing new cid on (red) : existing checked cid off : no cid 09 day/night mode switch mode number (1 ~ 8) on : while each mode 10 call forward -...

  • Page 330

    Function number function additional data led indication note 37 dnd/fwd override call none 38 message waiting none 39 room monitoring slow blink (red) : monitoring fast blink (red) : to be moni- tored 41 secretary buzzer extension number (4 digits) (sl1000) extension number (8 digits) (sl1100) on (r...

  • Page 331

    Function number function additional data led indication note 77 voice mail (in-skin) extension number or pilot number (4 digits) (sl1000) extension number or pilot number (8 digits) (sl1100) fast blink (red) : existing new message 78 conversation recording (in0skin vm) 0 = conversation re- cording 1...

  • Page 332

    Function number function additional data led indication note 93 room status indication none on : checked in and clean off : checked out (clean and available) slow blink : maid required medium blink : maid in room fast blink : inspect room (sl1000) 93 room status indication none on : checked in and c...

  • Page 333

    Function number function additional data led indication * 07 station park hold slow blink (red) : holding (sl1000) fast blink (red) : recall (sl1000) none (sl1100) default • the dss keys 001 ~ 060 of all dss consoles = dss/one-touch key 200 ~ 259. • the dss keys 061 ~ 114 of all dss consoles = no se...

  • Page 334

    Program 30 : dss/dls console setup 30-04 : dss console alternate answer (sl1100) level sa description use program 30-04 : dss console alternate answer to assign the alternate dss console station in case off-duty mode is set (by pressing the alt key on the dss console). Input data index 1 dss console...

  • Page 335

    Program 30 : dss/dls console setup 30-05 : dss console lamp table level in description use program 30-05 : dss console lamp table to define the led patterns for functions on the dss consoles. Input data item no. Item lamp pattern data default note 01 idle extension 0 ~ 7 0 02 busy extension 0 ~ 7 7 ...

  • Page 336

    Pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern #7 1 1 1 1 1 1 0 1 0 1 111 2 0 0 4 0 0 6 0 0 ...

  • Page 337

    Conditions none feature cross reference • direct station selection (dss) console l e d p a tte rn 0 :[o f f ] l e d p a tte rn 1 :[f l : o n (5 0 0 m s)/off(5 0 0 m s)] o n o ff o n o ff l e d p a tte rn 2 :[w k : o n (2 5 0 m s)/off(2 5 0 m s)] o n o ff l e d p a tte rn 3 :[r w : o n (1 2 5 m s)/of...

  • Page 338

    Program 31 : paging setup 31-01 : system options for internal/external paging level in description use program 31-01 : system options for internal/external paging to define the system options for internal/external paging. The system shows the name you program on the telephone display. Use the follow...

  • Page 339

    Item no. Item name input data default related program 04 privacy release time once the user initiates a meet-me confer- ence or voice call conference, the sys- tem waits this time for the paged party to join the call. 0 ~ 64800 seconds 90 seconds conditions none feature cross reference • paging, ext...

  • Page 340

    Program 31 : paging setup 31-02 : internal paging group assignment level in description use program 31-02 : internal paging group assignment to assign extensions to internal paging groups (i.E., page zones). The setting in this program also determines if the internal page group can receive internal ...

  • Page 341

    Program 31 : paging setup 31-03 : internal paging group settings level in description use program 31-03 : internal paging group settings to assign names to internal paging groups (i.E., page zones) and to define the splash tone for internal paging. The system shows the names you program on the telep...

  • Page 342

    Default item 01 : internal paging group name extension paging group name 01 group 1 02 group 2 : : 32 group 32 conditions none feature cross reference • paging, internal issue 1.0 sl1000/sl1100 program 31 program 31 : paging setup 2-320

  • Page 343

    Program 31 : paging setup 31-04 : external paging zone group level in description use program 31-04 : external paging zone group to assign each external paging zone to an exter- nal paging group. Users call the external paging group when broadcasting announcements to the ex- ternal zone. To simplify...

  • Page 344

    Program 31 : paging setup 31-05 : universal night answer/ring over page level in description use program 31-05 : universal night answer/ring over page to assign universal night answer ringing to each external paging zone. For each trunk port, make a separate entry for each external paging zone. For ...

  • Page 345

    Program 31 : paging setup 31-06 : external speaker control level in description use program 31-06 : external speaker control to define the settings for the external speaker using an amplifier. Input data external speaker number 1 ~ 3 item no. Item input data default 01 broadcast splash tone before p...

  • Page 346

    Program 31 : paging setup 31-07 : combined paging assignments level in description use program 31-07 : combined paging assignments to assign an external paging group (0 ~ 8) to an internal paging zone (0 ~ 32) for combined paging. When an extension user makes a combined page, they simultaneously bro...

  • Page 347

    Program 31 : paging setup 31-08 : bgm on external paging level in description use program 31-08 : bgm on external paging to set the background music option for each external paging zone. If enabled, the system plays background music over the zone when it is idle. Input data external speaker number 1...

  • Page 348

    Program 31 : paging setup 31-10 : external paging group basic setting level in description use program 31-10 : external paging group basic setting assigns the name of external paging group and defines the splash tone for external paging. Input data external speaker number 01 ~ 03 item no. Item input...

  • Page 349

    Program 32 : door box and sensor setup 32-01 : door box timers setup level in description use program 32-01 : door box timers setup to assign the timers used for the door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data item no. It...

  • Page 350

    Program 32 : door box and sensor setup 32-02 : door box ring assignment level sa description use program 32-02 : door box ring assignment to assign the extension which rings when a caller presses the associated door box call button. The door box feature is called door phone when programming via webp...

  • Page 351

    Program 32 : door box and sensor setup 32-03 : door box basic setup level in description use program 32-03 : door box basic setup to select the chime pattern and gain level for each door box. There are six distinctive chime patterns. The chime tones are defined in 80-01 : service tone setup. On page...

  • Page 352

    Program 32 : door box and sensor setup 32-04 : door box name setup level in description use program 32-04 : door box name setup to define the name of each door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data door box number 1 ~ 8 ...

  • Page 353

    Program 34 : tie line setup 34-01 : e&m tie line basic setup level in description use program 34-01 : e&m tie line basic setup to define the basic settings for each e&m tie line. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default description related p...

  • Page 354

    Program 34 : tie line setup 34-02 : e&m tie line class of service level in description use program 34-02 : e&m tie line class of service to assign a class of service to a tie line (there are 15 tie line classes of service). The class of service options are defined in program 20-14. For each tie line...

  • Page 355

    Program 34 : tie line setup 34-03 : trunk group routing for e&m tie lines level in description use program 34-03 : trunk group routing for e&m tie lines to assign the trunk group route 01 ~ 25) chosen when a user seizes a tie line and dials 9. (set trunk group routing in program 14-07.) if the syste...

  • Page 356

    Program 34 : tie line setup 34-04 : e&m tie line toll restriction class level in description use program 34-04 : e&m tie line toll restriction class to enter a toll restriction class for each tie line. There are 15 toll restriction classes which are defined in programs 21-05 and 21-06. For each tie ...

  • Page 357

    Program 34 : tie line setup 34-05 : tie line outgoing call restriction level in description use program 34-05 : tie line outgoing call restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.G., dialed from a tie line). For each inbound trunk group, enable ...

  • Page 358

    Program 34 : tie line setup 34-06 : add/delete digit for e&m tie line level in description use program 34-06 : add/delete digit for e&m tie line to set digits that the system should add or delete for tie lines. • delete digit some tie line networks pass the location number and extension number to th...

  • Page 359

    Program 34 : tie line setup 34-07 : e&m tie line timer level in description use program 34-07 : e&m tie line timer to define the system service tone timers. Input data item no. Item input data default 01 first digit pause (e&m immediate start) 0 ~ 64800 seconds 3 seconds 02 first digit pause (e&m wi...

  • Page 360

    Program 34 : tie line setup 34-08 : toll restriction data for e&m tie lines level in description use program 34-08 : toll restriction data for e&m tie lines to define the toll restriction data for e&m tie lines. This data should be defined if tie line toll restriction is enabled in program 21-05-13....

  • Page 361

    Program 34 : tie line setup 34-09 : ani/dnis service options level in description use program 34-09 : ani/dnis service options to define the ani/dnis service option setup for e&m class of service. Input data class of service 01 ~ 15 item no. Item input data default default related program cos 01 cos...

  • Page 362

    Item no. Item input data default default related program cos 01 cos 02 ~ 15 04 route table setup of target dial the option sets how the system uses the route data (gathered in item 3) to route incoming ani/dnis calls. If option 2 is selected, and the call is to be routed using the did table (1), up ...

  • Page 363

    Item no. Item input data default default related program cos 01 cos 02 ~ 15 09 calling number address length when item 01 = 0 (ani/dnis receive format is the address), use this option to specify the address length. The choices are from 1 ~ 8 digits. 1 ~ 8 7 7 34-09-01 conditions none feature cross r...

  • Page 364

    Program 34 : tie line setup 34-11 : e1 trunk basic setup level in description use program 34-11 : e1 trunk basic setup to define the basic setting of each e1 trunk. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Name input data default 01 e1 trunk type use this option to...

  • Page 365: 35-01 : Smdr Options

    Program 35 : smdr account code setup 35-01 : smdr options level in description use program 35-01 : smdr options to set the smdr (station message detail recording) options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range and default setting. I...

  • Page 366

    Program 35 : smdr account code setup 35-02 : smdr output options level in description use program 35-02 : smdr output options to set the smdr (station message detail recording) output options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range a...

  • Page 367

    Item no. Item input data default 12 did table name output determine if the did table name should be dis- played. 0 = not displayed 1 = displayed 0 13 cli output when did to trunk determine if the cli output should be displayed for did. 0 = not displayed 1 = displayed 0 14 date determine whether or n...

  • Page 368

    Feature cross reference • station message detail recording issue 1.0 sl1000/sl1100 program 35 program 35 : smdr account code setup 2-346.

  • Page 369

    Program 35 : smdr account code setup 35-03 : smdr port assignment for trunk group level in description use program 35-03 : smdr port assignment for trunk group to assign the smdr port for each trunk group. For each trunk group, select the smdr port where the incoming smdr information should be sent....

  • Page 370

    Program 35 : smdr account code setup 35-04 : smdr port assignment for department groups level in description use program 35-04 : smdr port assignment for department groups to assign the smdr port for each department group. For each department group, select the smdr port where the outgoing smdr infor...

  • Page 371

    Program 35 : smdr account code setup 35-05 : account code setup level in description use program 35-05 : account code setup to set various account code options for an extension class of service. Assign a class of service to extensions in program 20-06. Input data class of service number 01 ~ 15 item...

  • Page 372

    Program 35 : smdr account code setup 35-06 : verified account code table level in description use program 35-06 : verified account code table to enter account codes into the verified account code list. You can enter up to 800 codes with 1 ~ 16 digits, using the characters 0 ~ 9 or #. Use the lk1 to ...

  • Page 373

    Program 40 : voice recording system 40-01 : voice mail basic setup level in description use program 40-01 : voice mail basic setup to set the basic setting of voice mail. Conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 40 programming manual 2-351.

  • Page 374

    Program 40 : voice recording system 40-07 : voice prompt language assignment for vrs level in description use program 40-07 : voice prompt language assignment for vrs to specify the language to be used for the vrs prompts. Input data item no. Item input data default 01 voice prompt language assignme...

  • Page 375

    Program 40 : voice recording system 40-10 : voice announcement service option level in description in program 40-10 : voice announcement service option define the system options for the voice announcement feature. Input data item no. Item input data default related program 01 vrs fixed message enabl...

  • Page 376

    Feature cross reference • voice response system (vrs) issue 1.0 sl1000/sl1100 program 40 program 40 : voice recording system 2-354.

  • Page 377

    Program 40 : voice recording system 40-11 : preamble message assignment level in description in program 40-11 : preamble message assignment to assign the vrs message number to be used as the preamble message for each trunk. When the extension user answers the incoming call, the as- signed vrs messag...

  • Page 378: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-01 : system options for hotel/motel level in description use program 42-01 : system options for hotel/motel to assign the system options for hotel/motel service. Input data item no. Item input data default 01 answering message mode for wake up call (hotel mode) 0 = moh (h...

  • Page 379: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-02 : hotel/motel telephone setup level in description use program 42-02 : hotel/motel telephone setup to define the basic operation of the hotel/motel extensions. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input data d...

  • Page 380: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-03 : class of service options (hotel/motel) level in description use program 42-03 : class of service options (hotel/motel) to set the hotel/motel class of service (cos) options. Assign class of service to extensions in program 42-02 : hotel/motel telephone setup. There a...

  • Page 381: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-04 : hotel mode one-digit service codes level in description use program 42-04 : hotel mode one-digit service codes to set up the hotel mode one-digit ser- vice codes which are assigned in 42-02-01. For each department calling group (01 ~ 32), you enter the destination fo...

  • Page 382: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-05 : hotel room status printer level in description use program 42-05 : hotel room status printer to set the lan port to output the hotel data (check-out sheet, room status, etc.) and the output options for the hotel/ motel feature. Input data item no. Item input data def...

  • Page 383: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-08 : text message setup for hotel room status level in description use program 42-08 : text message setup for hotel room status to define the text message for hotel room status. Input data room status number 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, #, * room status 0 = check in 1 = ...

  • Page 384

    No. Room status fidelio code alphanumeric 12345678901234567890123456789012 * check in 4 check out 3 # check in 4 check out 3 conditions none feature cross reference • hotel/motel issue 1.0 sl1000/sl1100 program 42 program 42 : hotel setup 2-362.

  • Page 385

    Program 44 : ars/f-route setup 44-01 : system options for ars/f-route level in description use program 44-01 : system options for ars/f-route to define the system options for the ars/f- route feature. Input data item no. Item input data default 01 ars/f-route time schedule if this option is set to 0...

  • Page 386

    Program 44 : ars/f-route setup 44-02 : dial analysis table for ars/f-route access level in description use program 44-02 : dial analysis table for ars/f-route access to set the pre-transaction table for selecting ars/f-route. Input data dial analysis table number 001 ~ 120 item no. Item input data d...

  • Page 387

    Feature cross reference • automatic route selection (ars/f-route) issue 1.0 sl1000/sl1100 program 44 programming manual 2-365.

  • Page 388

    Program 44 : ars/f-route setup 44-03 : dial analysis extension table level in description when program 44-02-02 is set to type 3, use program 44-03 : dial analysis extension table to set the dial extension analysis table. These tables are used when the analyzed digits must be more than eight digits....

  • Page 389

    Program 44 : ars/f-route setup 44-04 : ars/f-route selection for time schedule level in description use program 44-04 : ars/f-route selection for time schedule to assign each ars/ f-route se- lection number to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for...

  • Page 390: 44-05 : Ars/f-Route Table

    Program 44 : ars/f-route setup 44-05 : ars/f-route table level in description use program 44-05 : ars/f-route table to set the ars/f-route table. There are four kinds of order. If the higher priority trunk groups are busy, the next order group is used. If a lower priority route is se- lected, the ca...

  • Page 391

    Feature cross reference • automatic route selection (ars/f-route) issue 1.0 sl1000/sl1100 program 44 programming manual 2-369.

  • Page 392

    Program 44 : ars/f-route setup 44-06 : additional dial table level in description use program 44-06 : additional dial table to set the additional dial table to add prior to the dialed ars/f-route number. The additional dial table used is determined in program 44-05-03. Input data additional dial tab...

  • Page 393

    Program 44 : ars/f-route setup 44-07 : gain table for ars/f-route access level in description use program 44-07 : gain table for ars/f-route access to set the gain/pad table. If an extension dials ars/f-route number: • the extension dial gain table, assigned in program 44-05, is activated. • the ext...

  • Page 394

    Program 44 : ars/f-route setup 44-08 : time schedule for ars/f-route level in description use program 44-08 : time schedule for ars/f-route to define the daily pattern of the ars/f-route feature. Ars/f-route has 10 time patterns. These patterns are used in programs 44-09 and 44-10. The daily pattern...

  • Page 395

    Program 44 : ars/f-route setup 44-09 : weekly schedule for ars/f-route level in description use program 44-09 : weekly schedule for ars/f-route to define a weekly schedule for using ars/ f-route. The pattern number is defined in program 44-08-01. Input data item no. Day number schedule pattern num- ...

  • Page 396

    Program 44 : ars/f-route setup 44-10 : holiday schedule for ars/f-route level in description use program 44-10 : holiday schedule for ars/f-route to define a yearly schedule for ars/f- route. This schedule is used for setting special days such as national holidays. The pattern number is defined in p...

  • Page 397

    Program 45 : voice mail integration 45-01 : voice mail integration options level in description use program 45-01 : voice mail integration options to customize certain voice mail integration op- tions. Input data item no. Item input data default related pro- gram 01 voice mail department group numbe...

  • Page 398

    Conditions none feature cross reference • voice mail integration (analog) issue 1.0 sl1000/sl1100 program 45 program 45 : voice mail integration 2-376.

  • Page 399: 45-02 : Nsl Option Setup

    Program 45 : voice mail integration 45-02 : nsl option setup level sa description use program 45-02 : nsl option setup to setup the nsl options for voice mail integration. Input data item no. Item input data default note 01 send dtmf tone or 6kd message 0 = send dtmf tone to slt-vm port 1 = send 6kd...

  • Page 400

    Program 45 : voice mail integration 45-04 : voice mail digit add assignment level in description use program 45-04 : voice mail digit add assignment to define the digits to add. Input data item no. Item input data default related program 01 remote logon (internal) up to four digits none 45-01-15 02 ...

  • Page 401: Digits

    Program 45 : voice mail integration 45-05 : voice mail send protocol signal without additional digits level in description use program 45-05 : voice mail send protocol signal without additional digits to send trunk number and/or station number information if integrating to voice mail when program 45...

  • Page 402: Program 47 : Inmail

    Program 47 : inmail 47-01 : inmail system options level in description use program 47-01 : inmail system options to set up the inmail system-wide options. Input data item no. Item input data default 02 inmail master name (mastername) the cpu must be reset for a change to this pro- gram to take effec...

  • Page 403

    Item no. Item input data default 07 digital pager callback number (pager cback) use this option to set the digital pager callback number portion of the message notification callout number for a digital pager. This is the portion of the callout number that is appended to the pager ser- vice telephone...

  • Page 404

    Item no. Item input data default 12 wait between rna non-pager callout attempts (notify rna intvl) use this option to set how long inmail waits (1 ~ 255 minutes), after it dials an unanswered non- pager callout destination, before retrying the call- out number. There are 3 types of unanswered non-pa...

  • Page 405

    Conditions • when changing 47-01-01 or 47-01-02, a system reset is required for the new setting to take effect. Feature cross reference none issue 1.0 sl1000/sl1100 program 47 programming manual 2-383.

  • Page 406: Program 47 : Inmail

    Program 47 : inmail 47-02 : inmail station mailbox options level in description use program 47-02 : inmail station mailbox options to set up a station/extension mailbox. Station mailboxes are automatically assigned as subscriber mailboxes. Normally, inmail station mailbox num- bers 1 ~ 64 should cor...

  • Page 407

    Item no. Item input data default 06 message retention use this option to determine how long a subscriber mailbox retains held and saved messages. If a mes- sage is left in a subscriber mailbox longer than this interval, inmail deletes it. 0 ~ 99 days (0 = indefinite) 0 07 recording conversation beep...

  • Page 408

    Item no. Item input data default 13 dialing option dialing option provides additional dialing options for next call routing mailbox calls (see next call rout- ing mailbox below). If enabled, a caller who ac- cesses the subscriber mailbox to leave a message can dial any of the options in the next cal...

  • Page 409

    Table 2-9 47-02-16 default table item name input data 47-02-16 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 410: Program 47 : Inmail

    Program 47 : inmail 47-03 : inmail group mailbox options level in description use program 47-03 : inmail group mailbox options to set up the 32 group mailboxes (01 ~ 32). A group mailbox is used for department group overflow and can be a subscriber or call routing. Input data group mailbox number 01...

  • Page 411: Program 47 : Inmail

    Program 47 : inmail 47-06 : group mailbox subscriber options level in description use program 47-06 : group mailbox subscriber options to set up a master mailbox assigned as a subscriber mailbox in 47-03-03 : master mailbox type. Input data group mailbox number 01 ~ 32 item no. Item input data defau...

  • Page 412

    Item no. Item input data default 06 message waiting lamp (update mw lamp) use this option to enable or disable message wait- ing light at the extension associated with the sub- scriber mailbox. For subscriber mailboxes, you should leave this option enabled. For guest mail- boxes, you should leave th...

  • Page 413

    Item no. Item input data default 18 enable email notification 0 = no 1 = yes 0 19 email address up to 48 characters no setting 20 include msg as attachment 0 = no 1 = yes 1 21 all message notification enabled 0 = no 1 = yes 1 22 all find-me follow-me enabled 0 = no 1 = yes 0 23 security code option ...

  • Page 414

    Feature cross reference none issue 1.0 sl1000/sl1100 program 47 program 47 : inmail 2-392.

  • Page 415: Program 47 : Inmail

    Program 47 : inmail 47-07 : inmail routing mailbox options level in description use program 47-07 : inmail routing mailbox options to set up the 32 routing mailboxes. Routing mailboxes can be either announcement or call routing mailboxes. Input data routing mailbox number 01 ~ 32 item no. Item input...

  • Page 416

    Table 2-11 47-07-03 default table item name input data 47-07-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fre...

  • Page 417: Program 47 : Inmail

    Program 47 : inmail 47-08 : call routing mailbox options level in description use program 47-08 : call routing mailbox options to set the options for mailboxes assigned as call routing mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data de...

  • Page 418

    Feature cross reference none issue 1.0 sl1000/sl1100 program 47 program 47 : inmail 2-396.

  • Page 419: Program 47 : Inmail

    Program 47 : inmail 47-09 : announcement mailbox options level in description use program 47-09 : announcement mailbox options to set the options for mailboxes assigned as announcement mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data de...

  • Page 420: Program 47 : Inmail

    Program 47 : inmail 47-10 : inmail trunk options level in description use program 47-10 : inmail trunk options to assign inmail options for each trunk. Currently, only 47-10-01 : answer table assignment is available. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item in...

  • Page 421

    Table 2-12 47-10-03 default table item name input data 47-10-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fre...

  • Page 422: Program 47 : Inmail

    Program 47 : inmail 47-11 : inmail answer table options level in description use program 47-11 : inmail answer table options to set options for the answer tables. Inmail pro- vides eight answer tables (1 ~ 8). To set up the schedules for each answer table, go to 47-12 : inmail answer table schedule....

  • Page 423

    Item no. Item input data default description 02 override mailbox category (override mb ctg) use this option to specify the category of the mailbox where automated atten- dant calls should route when you en- able answer schedule override. • if the override mailbox is a sub- scriber mailbox , the outs...

  • Page 424

    Item no. Item input data default description 03 default mailbox category (default mb ctg) use this option to specify the category of mailbox used as the default mail- box. • if the default mailbox is a sub- scriber mailbox , the outside caller hears the mailbox greeting (if re- corded) and can leave...

  • Page 425

    Feature cross reference none issue 1.0 sl1000/sl1100 program 47 programming manual 2-403.

  • Page 426: Program 47 : Inmail

    Program 47 : inmail 47-12 : inmail answer schedules level in description use program 47-12 : inmail answer schedules to set up the inmail automated attendant answer schedules. There are eight answer tables, with up to 10 answer schedules in each answer table. Input data answer table number 1 ~ 8 sch...

  • Page 427

    Item no. Item input data default description 01 schedule type 0 = undefined 1 = day of the week 2 = range of days 3 = date answer table 1/ schedule 1 = 2 all other schedules = 0 (entryxx schedule type) use this option to assign a sched- ule type to the selected answer schedule. The schedule type de-...

  • Page 428

    Item no. Item input data default description 02 answering mailbox cat- egory (entryxx mb ctg) use this option to specify the category of mailbox to which automated attendant calls should route when the sched- ule is in effect. If the answering mailbox is a subscriber mailbox , the out- side caller h...

  • Page 429

    Item no. Item input data default description 06 date (entryxx date) for date (type 3) answer schedules, use this option to select the date the answer schedule should be active. Mmdd for example : - 0101 = january 1 - 1231 = december 31 (0000 = undefined) all schedule = 0000 07 schedule start time (e...

  • Page 430: Program 47 : Inmail

    Program 47 : inmail 47-13 : inmail dial action tables level in description use program 47-13 : inmail dial action tables to set up the inmail dial action tables. The dial ac- tion table defines the options than an automated attendant caller can dial. A dial action table is asso- ciated with a call r...

  • Page 431

    Item no. Name input data description 01 action 0 = und (undefined) 1 = trf (transfer) 2 = utrf (unscreened transfer) 3 = rec1 4 = rec2 5 = logon 6 = hang up 7 = goto • trf action - screened transfer (1) (trf) • utrf action - unscreened transfer (2) (utrf) • rec1 action - quick message with greeting ...

  • Page 432

    Dial action table default settings key dial action table 1 dial action table 2 ~ 16 action data action data 7 0 (und) 0 0 (und) 0 8 0 (und) 0 0 (und) 0 9 6 (hang up) 0 0 (und) 0 0 2 (utrf) 200 0 (und) 0 * 3 (rec1) ixxx 0 (und) 0 # 5 (logon) ixxx 0 (und) 0 timeout 2 (utrf) 200 0 (und) 0 timeout provi...

  • Page 433: Program 47 : Inmail

    Program 47 : inmail 47-15 : routing directory mailbox options level in description use program 47-15 : routing directory mailbox options to define the routing directory mailbox options. This data is referred if program 47-07-02 (routing master mailbox type) was set to type 4 (directory). Input data ...

  • Page 434: Program 47 : Inmail

    Program 47 : inmail 47-17 : routing distribution mailbox options level in description use program 47-17 : routing distribution mailbox options to assign data when program 47-07-02 is set to 4 (distribution). Input data routing mailbox number 01 ~ 32 entry number 01 ~ 20 item no. Item input data defa...

  • Page 435: Program 47 : Inmail

    Program 47 : inmail 47-18 : inmail smtp setup level in description use program 47-18 inmail smtp setup to set the snmp e-mail notification. Input data item no. Item input data default 01 smtp enabled 0 = no 1 = yes 0 02 server name up to 48 characters no setting 03 smtp port 0 ~ 65535 25 04 encrypti...

  • Page 436: Program 47 : Inmail

    Program 47 : inmail 47-19 : inmail pop3 setup level in description use program 47-19 : inmail pop3 setup to set the inmail e-mail notification. Input data item no. Item input data default 01 server name up to 48 characters no setting 02 pop3 port 0 ~ 65535 110 03 encryption 0 = no 1 = yes 0 04 user ...

  • Page 437: Program 47 : Inmail

    Program 47 : inmail 47-20 : station mailbox message notification options level in description use program 47-20 : station mailbox message notification options to define the intramail station mailbox message notification options. Input data station mailbox number 001 ~ 128 (sl1000) 001 ~ 120 (sl1100)...

  • Page 438: Program 47 : Inmail

    Program 47 : inmail 47-21 : station mailbox find-me follow-me options level in description use program 47-21 : station mailbox find-me follow-me options to define the intramail station mailbox find-me follow-me options. Input data station mailbox number 001 ~ 128 (sl1000) 001 ~ 120 (sl1100) index nu...

  • Page 439: Program 47 : Inmail

    Program 47 : inmail 47-22 : group mailbox message notification options level in description use program 47-22 : group mailbox message notification options to define the intramail group mailbox message notification options. Input data group mailbox number 01 ~ 32 index number 1 ~ 5 item no. Item inpu...

  • Page 440: Program 47 : Inmail

    Program 47 : inmail 47-23 : group mailbox find-me follow-me options level in description use program 47-23 : group mailbox find-me follow-me options to define the intramail group mailbox find-me follow-me options. Input data group mailbox number 01 ~ 32 index number 1 ~ 3 item no. Item input data de...

  • Page 441

    Program 80 : basic hardware setup for system 80-01 : service tone setup level in description use program 80-01 : service tone setup to define up to 64 service tones. Each service tone is de- fined by the combination of 32 basic tones. Input data service tone number 01 ~ 64 item no. Item input data 0...

  • Page 442

    Basic tone no. Frequency (hz) level (db) 18 650 / 780 -13 / -19 19 780 / 1040 -13 / -19 20 1040 -13 21 450 -13 22 950 -13 23 1800 -13 24 400 / 450 -13/-13 25 400 - 13 26 350 / 440 - 13/- 13 27 420 (amplitude modulated) - 13 28 -- reserve -- - 29 -- reserve -- - 30 -- reserve -- - 31 -- reserve -- - ...

  • Page 443

    Ser- vice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 15 override tone 1 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) 16 lock-out tone 0 2 23 0 2 2 32 (0 db) 32 (0 db) 17 clock alarm tone 0 8 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 13 39 (+ 3.5 db) 39 (+ 3.5 db) 39 (+ 3.5 d...

  • Page 444

    Ser- vice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 31 paging tone 2 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) 32 splash tone 1 1 2 0 23 1 1 32 (0 db) 32 (0 db) 33 splash tone 2 2 2 0 23 1 1 32 (0 db) 32 (0 db) 34 splash tone 3 3 2 0 23 1 1 32 (0 db) 32 (0 db...

  • Page 445

    Ser- vice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 57 headset ear piece ringing tone 0 4 24 0 24 0 2 2 2 20 35 (+ 1.5 db) 35 (+ 1.5 db) 35 (+ 1.5 db) 35 (+ 1.5 db) 58 opening chime tone 1 8 2 2 14 14 15 15 16 16 2 2 2 2 2 2 6 4 32 (0 db) 26 (- 3 db) ...

  • Page 446: 80-02 : Dtmf Tone Setup

    Program 80 : basic hardware setup for system 80-02 : dtmf tone setup level mf description use program 80-02 : dtmf tone setup to define the duration (on time) and pause (off time) for dtmf dialing. This option affects all trunk line calls system wide. Make separate entries for duration and pause. It...

  • Page 447

    Program 80 : basic hardware setup for system 80-03 : dtmf tone receiver setup level in description use program 80-03 : dtmf tone receiver setup to define the various levels and timers for the dtmf tone receiver. Dtmf tone receiver type : • 1 = dtmf receiver for extension • 2 = dtmf receiver for trun...

  • Page 448

    Item no item input data 06 backward twist level 0 ~ 9 (1 db ~ 10 db) 07 on detect time 1 ~ 255 (15 + 15 ms ~ 3825 ms) 08 off detect time 1 ~ 255 (15 + 15 ms ~ 3825 ms) 09 area type 0 = other 1 = aust default item no item type 1 type 2 type 3 type 4 type 5 01 detect level 0 0 0 0 0 02 start delay tim...

  • Page 449

    Program 80 : basic hardware setup for system 80-04 : call progress tone detector setup level in description use program 80-04 : call progress tone detector setup to define the various levels and timers for the call progress tone detector. Tone detector type : • 1 = dial tone for trunk • 2 = busy ton...

  • Page 450

    Item no item input data 14 twist level 0 ~ 10 (1 db ~ 10 db) (0 = not used) default item name type 1 (dt) type 2 (bt) type 3 (rbt) type 4 type 5 1 detect level 0 (- 25 dbm) 0 (- 25 dbm) 0 (- 25 dbm) 0 0 2 min. Detect level 15 (- 25 dbm) 15 (- 25 dbm) 15 (- 25 dbm) 0 0 3 s/n ratio 4 (- 20 db) 4 (- 20...

  • Page 451

    Program 80 : basic hardware setup for system 80-05 : date format for smdr and system level in description use program 80-05 : date format for smdr and system to define the date format when printing out the smdr, alarm report, and system information report. Input data item no. Item input data default...

  • Page 452

    Program 80 : basic hardware setup for system 80-06 : reference impedance setup level in description use program 80-06: reference impedance setup to define the change of reference impedance (600 Ω or complex) in coiu pkg (sl1000) use program 80-06: reference impedance setup to define the change of re...

  • Page 453

    Program 80 : basic hardware setup for system 80-07 : call progress tone detector frequency setup level in description use program 80-07 : call progress tone detector frequency setup to set the frequency of the detection tone set with program 80-04-12 and program 80-04-13. Input data frequency table ...

  • Page 454: 80-08 : Mfc Tone Setup

    Program 80 : basic hardware setup for system 80-08 : mfc tone setup level in description use program 80-08 : mfc tone setup to define the duration (on time) and pause (off time) for mfc dialing. This option affects all trunk line calls system wide. And also it is possible to adjust the level of tone...

  • Page 455: 80-09 : Short Ring Setup

    Program 80 : basic hardware setup for system 80-09 : short ring setup level in description use program 80-09 : short ring setup to define the short ring tone for sl1000/sl1100 multiline ter- minals. Input data short ring number 01 ~ 32 item no. Item description default 01 frequency 1 refer to table ...

  • Page 456

    Data ring cycle (ms) 03 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 04 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 05 250 (on) / off 06 250 (on) / 250 (off) / 250 (on) / off 07 250 (on) / 250 (off) / 250 (on) / 250 (off) / 250 (on) / off 08 25...

  • Page 457

    Program 80 : basic hardware setup for system 80-11 : mfc tone receiver setup level in description use program 80-11 : mfc tone receiver setup to various data for the mfc signal detection. Input data mfc tone receiver type number 1 = mfc receiver for extension 2 = mfc receiver for trunk 3 = reserved ...

  • Page 458

    Item name type 1 type 2 type 3 type 4 type 5 07 on detect time 1 (30 ms) 1 (30 ms) 1 (30 ms) 1 (30 ms) 1 (30 ms) 08 off detect time 1 (30 ms) 1 (30 ms) 1 (30 ms) 1 (30 ms) 1 (30 ms) conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 80 program 80 : basic hardware setup for ...

  • Page 459

    Program 80 : basic hardware setup for system 80-12 : caller id receiver setup level in description use program 80-12 : caller id receiver setup defines the type and level for caller id detection of dsp. Input data item no. Item input data default note 01 type 0 = ntt 1 = other 2 = korea 1 02 level (...

  • Page 460

    Program 81 : basic hardware setup for trunk 81-01 : co initial data setup level in description use program 81-01 : co initial data setup to define the various basic data parameters for the coiu. Input data item no. Item input data default note 01 pcm encoding method specifica- tion 0 = μ-law 1 = a-l...

  • Page 461

    Item no. Item input data default note 28 dial pulse make time (10pps) 1 ~ 255 (5 ~ 1275 ms) 7 (35 ms) 29 dp inter-digit time (10pps) 1 ~ 255 (10 ~ 2550 ms) 61 (610 ms) 36 long ringing detection minimum time 1 ~ 255 (100 ~ 25500 ms) 24 (2400 ms) conditions none feature cross reference none issue 1.0 ...

  • Page 462

    Program 81 : basic hardware setup for trunk 81-04 : isdn bri layer 1 (t-point) initial data setup level mf description use program 81-04 : isdn bri layer 1 (t-point) initial data setup to define the various basic data for layer 1 of isdn bri. Input data item no. Item input data default 01 wait time ...

  • Page 463

    Program 81 : basic hardware setup for trunk 81-05 : isdn bri & pri layer 2 (t-point) initial data setup level mf description use program 81-05 : isdn bri & pri layer 2 (t-point) initial data setup to define the various basic data for layer 2 of isdn bri and pri. Input data item no. Item input data d...

  • Page 464

    Program 81 : basic hardware setup for trunk 81-06 : isdn bri & pri layer 3 (t-point) timer setup level in description use program 81-06 : isdn bri & pri layer 3 (t-point) timer setup to define the various basic tim- ers for layer 3 of isdn bri/pri (defined in program 10-03-04). Input data layer 3 ti...

  • Page 465

    Item no. Item description input data default 13 t314 specifies the timer value in 1/100ths of a second of the timer to be started when message segment is received. 1 ~ 254 seconds 4 seconds 14 t316 specifies the timer value in 1/100ths of a second of the timer to be started when re- start is sent. (...

  • Page 466

    Program 81 : basic hardware setup for trunk 81-07 : codec filter setup for analog trunk port level in description use program 81-07 : codec filter setup for analog trunk port to define the codec (qslac) filter for each analog trunk port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1...

  • Page 467

    Program 81 : basic hardware setup for trunk 81-08 : t1 trunk timer setup level in description use program 81-08 : t1 trunk timer setup to define the basic timer setting of each t1 trunk type. Input data item name input data default 01 answer signal detection time (loop) 1 ~ 250 (4 ms ~ 1000 ms) 15 (...

  • Page 468

    Item name input data default 32 hookflash send time (e&m) 1 ~ 255 (100 ms ~ 25500 ms) 5 (500 ms) 33 hookflash send time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 5 (500 ms) 34 pause send time (all) 1 ~ 255 (1 sec ~ 255 sec ) 3 (3 sec) 35 wink send duration time (did) 1 ~ 250 (8 ms ~ 2000 ms) 25 (200 ms) 36 ...

  • Page 469

    Item name input data default 69 guard time 1 (did) 1 ~ 255 (100 ms ~ 25500 ms) 9 (900 ms) 70 guard time 1 (e&m) 1 ~ 255 (100 ms ~ 25500 ms) 9 (900 ms) 71 guard time 1 (opx) 1 ~ 255 (100 ms ~ 25500 ms) 9 (900 ms) 72 guard time 2 (all) 1 ~ 250 (4 ms ~ 1000 ms) 3 (12 ms) 73 dial sending complete time 1...

  • Page 470

    Program 81 : basic hardware setup for trunk 81-09 : cot codec (qslac) filter setting level in description use program 81-09 : cot codec (qslac) filter setting to define the filter setting data (when pro- gram 81-07 is set to 4). Input data item name input data default 01 b1 filter setup (1) 0 ~ 255 ...

  • Page 471

    Item name input data default 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 170 34 r filter coefficients (2) 0 ~ 255 192 35 r filter coefficients (3) 0 ~ 255 187 36 r filter coefficients (4) 0 ~ 255 32 37 r filter coefficients (5) 0 ~ 255 203 38 r filter coefficients (6...

  • Page 472

    Program 81 : basic hardware setup for trunk 81-13 : e1 trunk timer setup level in description use program 81-13 : e1 trunk timer setup to define the basic timer setting of e1 trunk. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item name input data default 01 loop current detect...

  • Page 473

    Item name input data default 39 receive line block recover min time 1 ~ 255 (64 ms ~ 16320 ms) 32 (2048 ms) 40 transmit remove ring time 0 ~ 255 (0 ms ~ 1020 ms) 0 (0 ms) 41 transmit clear signal send time 1 ~ 255 (16 ms ~ 4080 ms) 63 (1008 ms) 42 transmit seizure signal time 1 ~ 255 (8 ms ~ 2040 ms...

  • Page 474: Extension

    Program 82 : basic hardware setup for extension 82-01 : incoming ring tone level in description use program 82-01 : incoming ring tone to set the incoming ring tones, which are the tones a user hears when a call rings an extension. These tones are grouped into four ring tone ranges (1 ~ 4), also cal...

  • Page 475

    Incoming ringing tone number tone type frequency 1 (hz) frequency 2 (hz) modulation pattern 4 (trunk incoming) high mid low 2000 hz 1400 hz 1100 hz 760 hz 660 hz 540 hz 8 hz modulation 8 hz modulation 8 hz modulation pattern 5 (intercom incoming pattern) high mid low 1100 hz 660 hz 520 hz 1400 hz 76...

  • Page 476: Extension

    Program 82 : basic hardware setup for extension 82-02 : key telephone led pattern setup (sl1000) level mf description use program 82-02 : key telephone led pattern setup to setup the led flashing pattern. Input data item no. Item input data default 01 led01 incoming extension/trunk call, voice call,...

  • Page 477

    Conditions none feature cross reference none pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern ...

  • Page 478: Extension

    Program 82 : basic hardware setup for extension 82-04 : astu initial data setup level in description use program 82-04 : astu initial data setup to set the basic data of the slt. Input data item no. Item input data default 01 companding method type 0 = μ-law 1 = a-law 1 02 ringing frequency 0 = 25 h...

  • Page 479: Extension

    Program 82 : basic hardware setup for extension 82-05 : isdn bri & pri layer2 (s-point) initial data setup level mf description use program 82-05 : isdn bri & pri layer2 (s-point) initial data setup to set the basic data for the layer 2 of isdn bri/pri s-point. Input data item no. Item name input da...

  • Page 480: Extension

    Program 82 : basic hardware setup for extension 82-06 : isdn bri & pri layer3 (s-point) timer setup level in description use program 82-06 : isdn bri & pri layer3 (s-point) timer setup to set the basic timer for the layer 3 of isdn bri & pri s-point. Input data layer3 timer type no. 1 ~ 5 item no. I...

  • Page 481: Extension

    Program 82 : basic hardware setup for extension 82-07 : codec filter setup for analog station port level in description use program 82-07 : codec filter setup for analog station port to set the filter value of the codec (qslac) filter of each analog port. Input data station port number 001 ~ 128 (sl...

  • Page 482: Extension

    Program 82 : basic hardware setup for extension 82-08 : sidetone volume setup level mf description use program 82-08 : sidetone volume setup for adjusting the telephone sidetone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Input data item no....

  • Page 483: Extension

    Program 82 : basic hardware setup for extension 82-09 : sliu codec filter data setup level in description use program 82-09 : sliu codec filter data setup to define the filter setting data (when program 82-07 is set to 4). Input data item name input data default 01 b1 filter setup (1) 0 ~ 255 105 02...

  • Page 484

    Item name input data default 31 z filter coefficients (14) 0 ~ 255 159 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 220 34 r filter coefficients (2) 0 ~ 255 1 35 r filter coefficients (3) 0 ~ 255 58 36 r filter coefficients (4) 0 ~ 255 32 37 r filter coefficients (5) ...

  • Page 485: Extension

    Program 82 : basic hardware setup for extension 82-13 : volume level data setup for txd tel2 [lkts] (sl1000) level in description use program 82-13 : volume level data setup for txd tel2 to defines each volume type in the speaker, and the group listening for txd tel2. Volume type means “small volume...

  • Page 486: Extension

    Program 82 : basic hardware setup for extension 82-14 : handset/headset gain setup for multi line telephone level in description use program 82-14: handset/headset gain setup for multi line telephone to define the handset/ headset gain level for multi line telephone. Input data extension number up t...

  • Page 487: Extension

    Program 82 : basic hardware setup for extension 82-18 : kst codec filter data setup (sl1000) level in description use program 82-18 : kst codec filter data setup to defines the codec (qslac) filter for each kst station port. Input data station port number 001 ~ 128 item no. Item input data default 0...

  • Page 488: Extension

    Program 82 : basic hardware setup for extension 82-19 : kst codec filter data setup (sl1000) level in description use program 82-19 : kst codec filter data setup to defines the kst codec (qslac) filter data. Input data item no. Item input data default 01 b1 filter setup (1) * this setting is applied...

  • Page 489

    Item no. Item input data default 30 z filter coefficients (13) 0 ~ 255 166 31 z filter coefficients (14) 0 ~ 255 159 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 220 34 r filter coefficients (2) 0 ~ 255 1 35 r filter coefficients (3) 0 ~ 255 58 36 r filter coefficient...

  • Page 490: Extension

    Program 82 : basic hardware setup for extension 82-20 : volume level data setup for kst (sl1000) level in description use program 82-20 : volume level data setup for kst to defines each volume type of the speaker, and the group listening for kst. Volume type means “small volume, middle volume (1), m...

  • Page 491: Extension

    Program 82 : basic hardware setup for extension 82-21 : sensor setup level in description use program 82-21 : sensor setup to setup the sensor for sl1000/sl1100. Input data sensor number 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Name input data default 01 sensor type set sensor type. 0 = close detect 1...

  • Page 492

    Program 84 : hardware setup for voipdb 84-01 : h.323 trunk basic information setup level in description use program 84-01 : h.323 trunk basic information setup to set the basic information of the h.323 trunk. Input data item no. Item input data default 02 number of g.711 audio frames 1 ~ 4 3 03 g.71...

  • Page 493

    Item no. Item input data default 45 high-speed signal data (fax pro- cedure signal) 0 ~ 2 0 46 tcf operation setting 1 = training signal (tcf) of the fax is locally gener- ated and checked. 2 = training signal (tcf) of the fax is sent over the network. 1 59 fax relay function 0 = disable 1 = enable ...

  • Page 494

    Program 84 : hardware setup for voipdb 84-02 : h.225 and h.245 information basic setup level in description use program 84-02 : h.225 and h.245 information basic setup to define the basic setup informa- tion of h.225 and h.245. Input data item no. Item input data default 01 h.225 alerting time 0 ~ 2...

  • Page 495

    Item no. Item input data default 32 rai retry count 0 ~ 255 2 33 call signaling port number 0 ~ 65535 : 0 ~ 1719, 1721 ~ 65535 1730 35 fast start mode 0 = disable 1 = enable 1 36 ras unicast port number 0 ~ 65535 20001 37 terminal type setting 0 ~ 255 60 conditions none feature cross reference none ...

  • Page 496

    Program 84 : hardware setup for voipdb 84-07 : firmware download setup level in description use program 84-07 : firmware download setup to configure the settings related to central firm- ware download for ip phones. Input data item no. Item input data default 01 server mode 0 = tftp 1 = ftp 0 02 fil...

  • Page 497: 84-09 : Vlan Setup

    Program 84 : hardware setup for voipdb 84-09 : vlan setup level in description use program 84-09 : vlan setup to set up the vlan data. I/f no.2 the packets send from lan i/f on voipdb is set the vlan tag. Input data interface number 1 ~ 2 item no. Item input data default 01 vlan 0 = disable (off) 1 ...

  • Page 498: 84-10 : Tos Setup

    Program 84 : hardware setup for voipdb 84-10 : tos setup level in description use program 84-10 : tos setup to set up the type of service data. Input data protocol type 1 ~ 3 = not used 4 = h.323 5 = rtp/rtcp 6 = sip 7 = not used 8 = sip-mlt 9 = sip trunk 10 = not used item no. Item input data defau...

  • Page 499

    Program 84 : hardware setup for voipdb 84-13 : sip trunk codec information basic setup level in description use program 84-13 : sip trunk codec information basic setup to set up the basic codec op- tions for sip trunks. Input data item no. Item input data default 01 number of g.711 audio frame maxim...

  • Page 500

    Item no. Item input data default 17 jitter buffer mode set the mode of the jitter buffer. 1 = size set to the fixed amount for the codec. 2 = the minimum/maximum range for the codec is used. 3 = the minimum/maximum range for the codec is used and adjusts at any time, regardless of silence. 1 = stati...

  • Page 501

    Item no. Item input data default 45 ilbc jitter buffer - minimum set the minimum value of the jitter buffer of ilbc is set. Jitter is the variation in the time between pack- ets arriving and the buffer allows this variation to be absorbed. 0 ~ 255 ms 30 46 ilbc jitter buffer - standard set the avera...

  • Page 502

    Program 84 : hardware setup for voipdb 84-14 : sip trunk basic information setup level in description use program 84-14 : sip trunk basic information setup to define the basic setup for sip trunks. Input data item no. Item input data default note 01 invite retx count specifies the number of times th...

  • Page 503

    Program 84 : hardware setup for voipdb 84-15 : h.323/sip phone keep alive setup level in description use program 84-15 : h.323/sip phone keep alive setup to set the keep alive configuration of the h.323/sip phone. Input data item no. Item input data default 01 registration information automatic dele...

  • Page 504

    Program 84 : hardware setup for voipdb 84-16 : voipdb limiter control gain setup level in description use program 84-16 : voipdb limiter control gain setup to set the limiter control gain configura- tion of voipdb. Input data item no. Item input data default 01 rx limiter control gain gain setting t...

  • Page 505

    Program 84 : hardware setup for voipdb 84-19 : sip extension codec information basic setup level in description use program 84-19 : sip extension codec information basic setup to define the codec infor- mation for the sip extensions. Input data item no. Item input data default 01 number of g.711 aud...

  • Page 506

    Item no. Item input data default 17 jitter buffer mode set the mode of the jitter buffer. 1 = size set to the fixed amount for the codec. 2 = the minimum/maximum range for the codec is used. 3 = the minimum/maximum range for the codec is used and adjust at any time, regardless of silence. 1 = static...

  • Page 507

    Item no. Item input data default 45 ilbc jitter buffer - minimum set the minimum value of the jitter buffer of ilbc is set. Jitter is the variation in the time between packets arriving and the buffer allows this variation to be ab- sorbed. 0 ~ 255 ms 30 46 ilbc jitter buffer - standard set the avera...

  • Page 508

    Program 84 : hardware setup for voipdb 84-20 : sip extension basic information setup level in description use program 84-20 : sip extension basic information setup to set up proxy information, session timers, called party information and expire value of invite. Input data item no. Item input data de...

  • Page 509

    Program 84 : hardware setup for voipdb 84-22 : dr700 multiline logon information setup level sa description use program 84-22 : dr700 multiline logon information setup to set the dr700 multiline logon information. Input data personal id index 001 ~ 128 (sl1000) 001 ~ 120 (sl1100) item no. Item input...

  • Page 510

    Program 84 : hardware setup for voipdb 84-23 : dr700 multiline basic information setup level in description use program 84-23 : dr700 multiline basic information setup to set the basic information for the dr700 multiline terminal. Input data item no. Item input data default 01 registration expire ti...

  • Page 511

    Feature cross reference none issue 1.0 sl1000/sl1100 program 84 programming manual 2-489.

  • Page 512

    Program 84 : hardware setup for voipdb 84-24 : dr700 multiline codec basic information setup level in description use program 84-24 : dr700 multiline codec basic information setup to set the codec of each type of dr700 multiline telephone. Input data type 1 = type 1 2 = type 2 3 = type 3 4 = type 4 ...

  • Page 513

    Item no. Item input data default 09 g.729 jitter buffer - minimum set the minimum value of the jitter buffer of g.729 is set. Jitter is the variation in the time between packets arriving and the buffer allows this variation to be absorbed. 0 ~ 300 ms 20 10 g.729 jitter buffer - standard set the aver...

  • Page 514

    Feature cross reference none issue 1.0 sl1000/sl1100 program 84 program 84 : hardware setup for voipdb 2-492.

  • Page 515

    Program 84 : hardware setup for voipdb 84-26 : voip basic setup (dsp) level in description use program 84-26 : voip basic setup to set the ip address and the port of voip. Input data slot number 0 voipdb gw number gw number will not be shown in telephone pro- gramming mode. 1 item no. Item input dat...

  • Page 516: 84-27 : Voip Basic Setup

    Program 84 : hardware setup for voipdb 84-27 : voip basic setup level in description use program 84-27 : voip basic setup to set the dtmf relay and the srtp mode of the voipdb. Input data slot number 0 item no. Item input data default 01 dtmf relay setup 0 = dtmf relay disabled 1 = in-band dtmf rela...

  • Page 517

    Feature cross reference none issue 1.0 sl1000/sl1100 program 84 programming manual 2-495.

  • Page 518

    Program 84 : hardware setup for voipdb 84-28 : dr700 multiline firmware name setup level in description use program 84-28 : dr700 multiline firmware name setup to set the firmware name to download for the ip phone. Input data terminal type 1 ~ 3 = not used 4 = ip4ww-24tixh item no. Item input data d...

  • Page 519

    Program 84 : hardware setup for voipdb 84-29 : sip-mlt codec information fixed mode setup level in description use program 84-29 : sip-mlt codec information fixed mode setup to set the codec data of the sip-mlt when it uses multicast. Input data type 1 = type 1 (multicast) 2 = type 2 (reserved) 3 = ...

  • Page 520

    Program 84 : hardware setup for voipdb 84-31 : voipdb echo canceller setup level in description use program 84-31 : voipdb echo canceller setup to sets voipdb echo canceller value. Input data type 1 = h.323 trunk 2 ~ 7 = not used 8 = sip trunk 9 = sip extension 10 = not used 11 = dr700 type 1 12 = d...

  • Page 521

    Item no. Item input data default 14 tdm tx gain compression mode 0 = disable 1 = enable 1 15 tdm tx gain compression threshold 0 = - 42 dbm 1 = - 41 dbm : 42 = 0 dbm 41 16 - not used - 17 - not used - 18 - not used - 19 rtp echo canceller mode 0 = disable 1 = enable 0 20 rtp echo canceller nlp mode ...

  • Page 522

    Item no. Item input data default 37 tdm echo canceller nlp mode (4w) 0 = disable 1 = enable 2 = echo path mode 3 = echo path auto detect mode 1 conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 84 program 84 : hardware setup for voipdb 2-500

  • Page 523: 90-01 : Installation Date

    Program 90 : maintenance program 90-01 : installation date level in description use program 90-01 : installation date to define the installation date of the system. Input data item no. Item input data default 01 year 00 ~ 99 00 (no setting) 02 month 01 ~ 12 00 (no setting) 03 day 01 ~ 31 00 (no sett...

  • Page 524

    Program 90 : maintenance program 90-02 : programming password setup level in description use program 90-02 : programming password setup to set the system passwords. For password entry, the system allows eight users to be defined. Each user can have a: • unique alphanumeric name (up to 10 alphanumeri...

  • Page 525

    Feature cross reference none issue 1.0 sl1000/sl1100 program 90 programming manual 2-503.

  • Page 526: 90-03 : Save Data

    Program 90 : maintenance program 90-03 : save data level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-03 : save data to save the programmed data on the cf card. This program should be used after changing the programmed d...

  • Page 527: 90-04 : Load Data

    Program 90 : maintenance program 90-04 : load data level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-04 : load data to load the system data from the inserted cf card into the pz-vm21 daughter board installed to the syst...

  • Page 528: 90-05 : Slot Control

    Program 90 : maintenance program 90-05 : slot control level in description note: this program is available via telephone programming and webpro not through pc program- ming. Use program 90-05 : slot control to reset or delete (uninstall) units (slots 1 ~ 16 (sl1000) 1 ~ 24 (sl1100)). Delete allows y...

  • Page 529: 90-06 : Trunk Control

    Program 90 : maintenance program 90-06 : trunk control level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-06 : trunk control for trunk maintenance. Busy out lets you block a unit from plac- ing outgoing calls (just like ...

  • Page 530: 90-07 : Station Control

    Program 90 : maintenance program 90-07 : station control level sa description note: this program is available via telephone programming and webpro not through pc program- ming. Use program 90-07 : station control for extension maintenance. Input data menu number 1 = hardware reset 2 = software reset...

  • Page 531: 90-08 : System Reset

    Program 90 : maintenance program 90-08 : system reset level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-08 : system reset to perform a system reset. Input data item no. Item input data 01 system reset dial 1 + press hol...

  • Page 532

    Program 90 : maintenance program 90-09 : automatic system reset time setup level in description use program 90-09 : automatic system reset time setup to define the time for the system to auto- matically reset. Input data item no. Item input data default 01 month 00 ~ 12 if the month is set to 00 and...

  • Page 533

    Program 90 : maintenance program 90-10 : system alarm setup level in description use program 90-10 : system alarm setup to assign a status to system alarms. You can designate an alarm as major or minor. This program also assigns whether or not the alarm information is reported to the pre-defined des...

  • Page 534

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 3 2 0 connection fault be- tween cpu and other pkgs. The error occurred when communicat- ing with the pack- age. When the package is broken, it recog- nizes it as a com- munication fault. 1 the unit is not completely in...

  • Page 535

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 6 0 0 blocking the link of termi- nals connected with the esi package came off. 1 terminal breakdown. 2 faulty wiring and wiring ter- mination. 3 external noise. 4 esi package breakdown. Confirm the termi- nal connected...

  • Page 536

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 30 2 0 smdr buf- fer full the temporary buf- fer for smdr in main device over- flowed, and a part of output smdr data disappeared because it could not output smdr data. 1 problem of wir- ing to connect main device with ...

  • Page 537

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 60 2 0 sip regis- tration error notifi- cation. 1 the registration of the sip trunk to the sip server failed. 2 the registration of the sip trunk to the sip server failed in the authentica- tion. 3 there is no re- spons...

  • Page 538

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 66 2 0 sip exten- sion li- cense error. More than the num- ber of licenses to which the sip ex- tension terminal was turned on at register. • wrong number of licenses. 1 confirm the number of li- censes for sip extensio...

  • Page 539

    Program 90 : maintenance program 90-11 : system alarm report level in description use program 90-11 : system alarm report to define the details of the system alarm report. Input data item no. Item input data default 02 report method when alarm reports are e-mailed, set this option to 1. E-mail addre...

  • Page 540

    Program 90 : maintenance program 90-12 : system alarm output level in description use program 90-12 : system alarm output to set the options for the alarm report. This program has six separate menu options. Define the output port to be used as the output for system alarm report and set the system al...

  • Page 541

    Program 90 : maintenance program 90-13 : system information output level in description use program 90-13 : system information output to define the output port to be used as the system information output. Input data item no. Item input data default 01 output port type indicate the type of connection...

  • Page 542

    Program 90 : maintenance program 90-16 : main software information level in description use program 90-16 : main software information to display the main software information on the cpu. Input data item no. Item input data default 01 version number 01.00 ~ 99.99 ascii code (5 bytes) 02 software rele...

  • Page 543

    Program 90 : maintenance program 90-17 : firmware information level in description use program 90-17 : firmware information to display the firmware versions of the various system units. Input data item no. Item input data default 01 dsp firmware version no. 00.00.00.00 ~ 15.15.15.15 bcd code (2 byte...

  • Page 544

    Program 90 : maintenance program 90-19 : dial block release level sa description note: this program is available via telephone programming and webpro not through pc program- ming. When the extension number is entered in program 90-19 : dial block release , the extension is re- leased from the dial b...

  • Page 545

    Program 90 : maintenance program 90-20 : traffic report data setup level in description use program 90-20 : traffic report data setup to define the details of the traffic report. Input data item no. Item input data default 01 call traffic output 0 = not measured 1 = measure 0 03 all line busy output...

  • Page 546

    Program 90 : maintenance program 90-21 : traffic report output level in description use program 90-21 : traffic report output to define the output port to be used as the traffic report output. Input data item no. Item input data default 01 output port type 0 = no setting 3 = lan 0 conditions none fe...

  • Page 547

    Program 90 : maintenance program 90-23 : deleting registration of ip telephones level in description note: this program is available via telephone programming and webpro not through pc program- ming. Use program 90-23 : deleting registration of ip telephones to delete the registered ip telephone fro...

  • Page 548

    Program 90 : maintenance program 90-24 : system alarm report notification time setup level in description use program 90-24 : system alarm report notification time setup to set the date and time for the alarm report to print. Input data notification number 1 ~ 12 item no. Item input data default 01 ...

  • Page 549

    Program 90 : maintenance program 90-25 : system alarm report cc mail setup level in description use program 90-25 : system alarm report cc mail setup to define the mail address to receive the system alarm report cc mail setup. Input data cc number 1 ~ 5 item no. Item input data default 01 cc mail ad...

  • Page 550

    Program 90 : maintenance program 90-26 : program access level setup level in description use program 90-26 : program access level setup to define the password access level required to change a system program. Input data program numbers 1001 ~ 9903 item no. Item input data default 01 maintenance leve...

  • Page 551

    Program 90 : maintenance program 90-28 : user programming password setup level in description use program 90-28 : user programming password setup to set the password used to enter the user programming mode. Input data extension numbers maximum four digits (sl1000) maximum eight digits (sl1100) item ...

  • Page 552

    Program 90 : maintenance program 90-31 : dim access over ethernet level in description use program 90-31 : dim access over ethernet to enable dim (diagnostic information mainte- nance) access over the lan, and to define the user name and password. Dim is a maintenance tool used by engineering to ext...

  • Page 553

    Program 90 : maintenance program 90-33 : preselected data setup level in description note: this program is available only via telephone programming and not through pc programming. Use 90-33 : preselected data setup to setup the system to preselected setting. Input data item no. Item name input data ...

  • Page 554

    Program no. Name default note 22-01-03 incoming ring no answer alarm start timer 30 22-01-04 normal dil incoming no answer timer 30 22-01-08 did (ddi) pilot call no answer timer 30 22-08-01 second irg setup for unanswered 1 (all trunks : all modes : irg1) 25-03-01 dud/disa transfer ring group at wro...

  • Page 555

    Program no. Name default 10-01-05 - hour 18 10-01-06 - minute 30 10-01-07 - second 0 80-01-02 basic tone no 1 (svc tone 2 unit 1) 12-01-02 automatic night mode switch 0 20-02-07 display mode of date and time 8 20-02-09 disconnect supervision 1 20-02-12 mode setting for incoming call from extension 1...

  • Page 556

    Program no. Name default 20-17-01 operator’s extension number 200 (operator 1 = 200) 30-02-01 dss console extension assignment 200 (dss console no.1 = 200) 10-02-01 country code 56 15-02-01 display language selection 12 40-07-01 voice prompt language assignment for sys- tem based 7 47-02-16 voice pr...

  • Page 557

    Program no. Name default note 35-01-04 smdr-omit digits 0 (port 1 only) 35-02-09 smdr-extension number or name 1 (port 1 only) 35-02-14 smdr-date 1 (port 1 only) 20-02-07 time and date display mode 5 15-03-03 terminal type 1 (all stations) 21-01-06 dial pause at first digit 1 20-13-01 long conversat...

  • Page 558

    Program no. Name default note 25-07-03 disconnect after did/disa re-transfer to irg 180 20-02-11 default setting of microphone of key telephone 0 24-02-03 delayed call forwarding time 16 14-02-02 ring detect type this option to sets extended ring detect or immediate ring detect for the trunk 1 (trun...

  • Page 559

    Program no. Name default 12-02-02 automatic night service patterns ( end of time ) modegrp 1-4, time pattern 01, set time 01 = 09:00 modegrp 1-4, time pattern 01, set time 02 = 18:00 modegrp 1-4, time pattern 01, set time 03 = 00:00 12-02-03 automatic night service patterns ( mode no. ) modegrp 1-4,...

  • Page 560

    Program no. Name default 21-05-08 restriction table class 1 set 1 class 2 set 2 class 3 set 3 class 4 set 4 21-15-01 2nd trk ace route tbl 2 22-01-11 msg interval 10 22-14-01 message1 start time 1 22-14-03 msg1 count 1 22-14-05 msg2 count 1 22-14-07 disconnect time 1 22-15-01 message1 start time 1 2...

  • Page 561

    Hong kong program no. Name default 14-01-13 loop disconnect supervision 1 (trunks 1 ~ 27) 14-02-02 ring detect type 1 (trunks 1 ~ 27) 14-02-04 flash for timed flash or disconnect 0 (trunks 1 ~ 27) 14-02-09 busy tone detection 1 (trunks 1 ~ 27) 14-02-10 caller-id 1 (trunks 1 ~ 27) 14-02-18 busy tone ...

  • Page 562

    Program no. Name default 80-07-01 table 3 (frequency) 62 81-01-14 flash (hooking 1) 25 81-07-01 codec filter type for analog trunk port 0 (trunks 1 ~ 27) 10-02-01 country code 852 brazil program no. Name default note 10-20-01 tcp port smdr ex - dev 5 60000 11-01-01 system numbering - acc operator di...

  • Page 563

    Program no. Name default note day / night mode 8 - (mode grp 1) 14-01-01 trunk name linha 01 ~ 51 14-01-13 loop disconnect supervision 1 (all trunk) 14-01-14 long conversation cut off 1 (all trunk) 14-01-15 long conversation alarm before cut off 1 (all trunk) 14-01-17 trunk to trunk warning tone for...

  • Page 564

    Program no. Name default note 20-16-01 selectable display message message number 1 reuniÃo_# # : # # message number 2 serviÇo_externo message number 3 retorna_ # # : # # message number 4 ligar _ # # # # # # # # # # message number 5 ligar_apÓs_ # # : # # message number 6 almoÇo message number 7 viage...

  • Page 565

    Program no. Name default note dial analysis table number 173 094@@@@@@@@@ dial analysis table number 174 095@@@@@@@@@ dial analysis table number 175 096@@@@@@@@@ dial analysis table number 176 097@@@@@@@@@ dial analysis table number 177 098@@@@@@@@@ dial analysis table number 178 099@@@@@@@@@ dial a...

  • Page 566

    Program no. Name default note dial analysis table number 167 1 dial analysis table number 168 1 dial analysis table number 169 1 dial analysis table number 170 1 dial analysis table number 171 1 dial analysis table number 172 1 dial analysis table number 173 1 dial analysis table number 174 1 dial a...

  • Page 567

    Program no. Name default note dial analysis table number 161 10 dial analysis table number 162 10 dial analysis table number 163 10 dial analysis table number 164 10 dial analysis table number 165 10 dial analysis table number 166 10 dial analysis table number 167 10 dial analysis table number 168 1...

  • Page 568

    Program no. Name default note dial analysis table number 155 2 dial analysis table number 156 2 dial analysis table number 157 2 dial analysis table number 158 2 dial analysis table number 160 2 dial analysis table number 161 2 dial analysis table number 162 2 dial analysis table number 163 2 dial a...

  • Page 569

    Program no. Name default note 40-08-01 voice prompt language assignment 9 80-04-04 no tone time type 2 bt 7 80-04-06 on minimum time type 2 bt 6 80-04-07 on maximum time type 2 bt 8 80-04-08 off minimum time type 2 bt 6 80-04-09 off maximum time type 2 by 8 80-07-01 frequency table 1 42 80-08-01 dur...

  • Page 570

    Thailand program no. Name default 10-02-01 country code 66 india program no. Name default 10-02-01 country code 91 conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 90 program 90 : maintenance program 2-548.

  • Page 571

    Program 90 : maintenance program 90-34 : firmware information level in description use program 90-34 : firmware information to list the package type and firmware units installed in the system. Input data slot number 00 ~ 16 (sl1000) 0 ~ 9 (sl1100) item no. Item display data 01 package name pkg name ...

  • Page 572

    Program 90 : maintenance program 90-35 : wizard programming level setup level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-35 : wizard programming level setup to set the maintenance level for wizard programming. Input da...

  • Page 573

    Program 90 : maintenance program 90-36 : firmware update time setting level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-36 : firmware update time setting to define the data for the firmware update fea- ture. This data i...

  • Page 574

    Program 90 : maintenance program 90-38 : user programming data level setup level in description use program 90-38 : user programming data level setup sets system data to turn on/off each user programming feature. Issue 1.0 sl1000/sl1100 program 90 program 90 : maintenance program 2-552.

  • Page 575

    Input data item no. Item program (reference only) input data default 01 time setting 10-01 (11-10-03) 0 = turn off 1 = turn on 1 = turn on 02 change of music on hold tone 10-04 (11-10-02) 1 = turn on 03 automatic night service pattern 12-02 1 = turn on 04 weekly night service switching 12-03 1 = tur...

  • Page 576

    Conditions none feature cross reference • maintenance issue 1.0 sl1000/sl1100 program 90 program 90 : maintenance program 2-554.

  • Page 577

    Program 90 : maintenance program 90-39 : virtual loop back port reset level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-39 : virtual loop back port reset to reset to initial status. Input data item no. Item input data 0...

  • Page 578

    Program 90 : maintenance program 90-41 : server setting to update terminal local data level in description use program 90-41 : server setting to update terminal local data to define the primary dns server address, the secondary dns server address and the data roaming server address. Input data serve...

  • Page 579

    Program 90 : maintenance program 90-42 : dr700 multiline terminal version information level in description use program 90-42 : dr700 multiline terminal version information to set the hardware version and firmware version of the dr700 mlt terminal. Input data terminal type 1 ~ 3 = not used 4 = ip4ww-...

  • Page 580

    Program 90 : maintenance program 90-43 : deleting terminal license of dr700 level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-43 : deleting terminal license of dr700 to delete the terminal license information delivered ...

  • Page 581

    Program 90 : maintenance program 90-44 : deleting terminal license of tcp interface level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-44 : deleting terminal license of tcp interface to delete the terminal license in- fo...

  • Page 582: Telephone

    Program 90 : maintenance program 90-45 : temporary password change for multiline telephone level in description note: this program is available via telephone programming and webpro not through pc program- ming. Use program 90-45 : temporary password change for multiline telephone to change the tempo...

  • Page 583

    Program 90 : maintenance program 90-50 : system alarm display setup level in description use program 90-50 : system alarm display setup to set the system alarm report display. Input data index number 01 ~ 50 item no. Item input data default 01 system alarm display telephone up to four digits (sl1000...

  • Page 584

    Program 90 : maintenance program 90-51 : alarm setup for maintenance exchange level in description use program 90-51 : alarm setup for maintenance exchange to set the day for the maintenance exchange of parts that need regular maintenance. Input data index 1 ~ 10 item no. Item input data default 01 ...

  • Page 585

    Program 90 : maintenance program 90-52 : system alarm save level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-52 : system alarm save for the system alarm output operation. Input data item no. Item input data default 01 s...

  • Page 586

    Program 90 : maintenance program 90-53 : system alarm clear level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-53 : system alarm clear to clear the system alarm. Input data item no. Item input data default 01 clear all a...

  • Page 587

    Program 90 : maintenance program 90-54 : pc/web programming level in description use program 90-54 : pc/web programming sets parameters for pc and web programming. Input data item no. Item input data default 01 web pro tcp port number the port number of tcp of the web pro- gramming is set. The port ...

  • Page 588

    Program 90 : maintenance program 90-55 : free license select level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-55 : free license select to validate the free license. Input data item no. Item input data default 01 start ...

  • Page 589: 90-56 : Ntp Setup

    Program 90 : maintenance program 90-56 : ntp setup level in description use program 90-56 : ntp setup to set the ntp. Input data item no. Item input data default 01 ntp synchronize 0 = no 1 = yes 0 02 server address ipv4 form : xxx.Xxx.Xxx.Xxx ipv6 form : xxxx.Xxxx.Xxxx.Xxxx.Xxxx no setting conditio...

  • Page 590

    Program 90 : maintenance program 90-57 : backup recovery data level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-57 : backup recovery data to backup the system data in the compact flash memory on the cpu and to make the ...

  • Page 591

    Program 90 : maintenance program 90-58 : restore recovery data level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-58 : restore recovery data to select the recovery data stored in the compact flash memory of the cpu. Afte...

  • Page 592

    Program 90 : maintenance program 90-59 : delete recovery data level sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-59 : delete recovery data to select and delete the recovery data stored in the compact flash memory of the ...

  • Page 593

    Program 90 : maintenance program 90-60 : t1/isdn layer status information level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-60 : t1/isdn layer status information to display layer status information for t1/ pri/bri packa...

  • Page 594: 90-63 : Dr700 Control

    Program 90 : maintenance program 90-63 : dr700 control level in description use program 90-63 : dr700 control to adjust settings of the dr700. Input data item no. Item input data default 01 priority timer 0 ~ 255 80 conditions none feature cross reference none issue 1.0 sl1000/sl1100 program 90 prog...

  • Page 595

    Program 90 : maintenance program 90-65 : 1st party cti authentication password setup level sa description use program 90-65 : 1st party cti authentication password setup to set the authentication pass- word. Input data item no. Item input data default 01 password sets the authentication password whe...

  • Page 596

    Program 90 : maintenance program 90-66 : ftp firmware update setup level in description use program 90-66 : ftp firmware update setup to setup the login info to connect to the ftp server. Input data item no. Item input data default 01 user name up to 32 characters none 02 password up to 32 character...

  • Page 597

    Program 90 : maintenance program 90-67 : backup data auto-save interval time set level in description use program 90-67 : backup data auto-save interval time set to set time interval d-ram data that is saved in f-rom memory. D-ram memory : configuration information such as call transfer and do not d...

  • Page 598

    Program 90 : maintenance program 90-68 : side tone auto setup level in description note: this program is available only via telephone programming and not through pc programming. Use program 90-68 : side tone auto setup to setup the volume level of side tone for each analog trunk port. This program w...

  • Page 599: 92-01 : Copy Program

    Program 92 : copy program 92-01 : copy program level in description note: this program is available only via telephone programming and not through pc programming. Use program 92-01 : copy program to copy the data for one program to another multiline terminal, port, group, or other number. Refer to t...

  • Page 600

    Program no. Program name note 22-08 second irg setup for unanswered dil / irg 31-05 incoming ring tone audible on external speaker 81–07 codec filter setup for analog trunk port trunk group base program no. Program name note 35-03 smdr port assignment for trunk group extension base program no. Progr...

  • Page 601

    Dss console base program no. Program name note 30-01 dss console operation mode 30-03 dss key assignment door box base program no. Program name note 32-02 door box ring assignment conditions • using this program to copy a multiline terminal programmable function keys, copies all keys whether or not ...

  • Page 602

    Program 92 : copy program 92-02 : delete all extension numbers level in description note: this program is available only via telephone programming and not through pc programming. Use program 92-02 : delete all extension numbers to delete all extension numbers 02>, . However, the extension number of ...

  • Page 603

    Program 92 : copy program 92-03 : copy program by port number level in description note: this program is available only via telephone programming and not through pc programming. Use program 92-03 : copy program by port number to copy extension and the data of each out- side line. Input data program ...

  • Page 604

    Program 92 : copy program 92-04 : extension data swap level in description note: this program is available only via telephone programming and not through pc programming. Use program 92-04 : extension data swap to swap data between two extensions. Input data item no. Item input data 01 1st extension ...

  • Page 605

    Program number program name note 21-11 hotline assignment 21-13 isdn calling party number setup for extension 21-15 individual trunk group routing for extensions 21-18 ip trunk (h.323) calling party number setup for extension 21-19 ip trunk (sip) calling party number setup for extension 21-20 sip tr...

  • Page 606

    Program 92 : copy program 92-05 : extension data swap password level in description use program 92-05 : extension data swap password to define the 4-digit password for each exten- sion to allow extension data swap. Input data extension number up to four digits. (sl1000) up to eight digits. (sl1100) ...

  • Page 607: 92-06 : Fill Command

    Program 92 : copy program 92-06 : fill command level in description use program 92-06 : fill command to allocate the data of each extension number of each extension group or each table. Input data program number xx - xx item no. Item input data 01 source number each extension port = 001 ~ 128 (sl100...

  • Page 608: 92-07 : Delete Command

    Program 92 : copy program 92-07 : delete command level in description use program 92-07 : delete command to delete the data of each extension number of each exten- sion group or each table. Input data program number xx-xx item no. Item input data 01 destination number (from) each extension port = 00...

  • Page 609

    Memo issue 1.0 sl1000/sl1100 programming manual 2-587.

  • Page 610

    Programming manual nec corporation issue 1.0