1. DL manuals
  2. NEC
  3. Telephone System
  4. SL1000
  5. Programming Manual

NEC SL1000 Programming Manual

Summary of SL1000

  • Page 1

    Programming manual a50-031167-002 eu issue 3.01 dec 2012.

  • Page 2: Copyright

    Copyright nec corporation reserves the right to change the specifications, functions, or features at any time without notice. Nec corporation has prepared this document for use by its employees and customers. The information contained herein is the property of nec corporation and shall not be reprod...

  • Page 3: Table of Contents

    Table of contents chapter 1 introduction section 1 before you start programming.......................................................... 1-1 section 2 how to use this manual........................................................................... 1-1 section 3 how to enter programming mode..........

  • Page 4

    10-50 : license information.............................................................................. 2-51 10-51 : pri/t1/e1 selection of pri.................................................................. 2-52 10-52 : free/demo license information.................................................

  • Page 5

    15-03 : single line telephone basic data setup.......................................... 2-137 15-05 : ip telephone terminal basic data setup.......................................... 2-140 15-06 : trunk access map for extensions..................................................... 2-143 15-07 : pro...

  • Page 6

    20-37 : operator extension group setup....................................................... 2-223 20-38 : operator group setting...................................................................... 2-224 20-39 : shortcut operation setup (sl1000)................................................... ...

  • Page 7

    22-17 : dial-in conversion table area setup for time pattern...................... 2-285 22-18 : private call assignment setup.......................................................... 2-286 22-19 : did mfc dialing options .................................................................. 2-288 22-2...

  • Page 8

    31-06 : external speaker control................................................................... 2-349 31-07 : combined paging assignments......................................................... 2-350 31-08 : bgm on external paging....................................................................

  • Page 9

    45-02 : nsl option setup.............................................................................. 2-412 45-04 : voice mail digit add assignment....................................................... 2-413 45-05 : voice mail send protocol signal without additional digits................ 2-414 pr...

  • Page 10

    82-14 : handset/headset gain setup for multi line telephone..................... 2-504 82-18 : kst codec filter data setup (sl1000).......................................... 2-505 82-19 : kst codec filter data setup (sl1000).......................................... 2-506 82-20 : volume level data s...

  • Page 11

    90-38 : user programming data level setup................................................ 2-602 90-39 : virtual loop back port reset............................................................. 2-604 90-41 : server setting to update terminal local data.................................. 2-605 90-42 :...

  • Page 12: List of Tables

    List of tables table 1-1 keys for entering data (sl1000)....................................................................... 1-4 table 1-2 keys for entering data (sl1100)....................................................................... 1-5 table 1-3 keys for entering names.....................

  • Page 13: Introduction

    Introduction s ection 1 before you start programming before customizing your system be sure to read this chapter first. This chapter provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this cha...

  • Page 14

    15-07-01 tel ky01 = *01 - + (ip phone) (sl1000) 15-07-01 tel ky01 = *01 - + (sl1100) tells you to enter the programming mode, dial 150701 from the telephone dial pad. After you do, you will see the message “15-07-01 tel” on the first line of the telephone display. This indicates the program number (...

  • Page 15

    5. Dial the system password + hold. Refer to the following table for the default system passwords. To change the passwords, use 90-02 : programming password setup on page 2-549 . Program mode (sl1000) program mode base service op1 op2 (sl1100) password user name level programs at this level ****** n...

  • Page 16

    To save a customer’s database, a blank compact flash (cf) card is required. Insert the cf card into the cpu and, using program 90-03, save the software to the cf card. (program 90-04 is used to reload the customer data if necessary.) note that a cf card can only hold one customer database. Each data...

  • Page 17

    When you want to ... Telephone programming move cursor to right cursor key (right) table 1-2 keys for entering data (sl1100) when you want to ... Telephone programming enter data into program 0 ~ 9, * , # line key (1 ~ 6) next index cursor key (up) prior index cursor key (down) select data line key ...

  • Page 18

    Use this keypad digit ... When you want to ... 6 enter characters : m-o, m-o, 6. 7 enter characters : p-s, p-s, 7. 8 enter characters : t-v, t-v, 8. 9 enter characters : w-z, w-z, 9. 0 enter characters : 0 ! “ # $ % & ’ ( ) ô õ ú å ä æ ö ü α ε θ В * enter characters : * + , - . / : ; ? π Σ σ Ω ∞ ¢ £...

  • Page 19

    Softkey display prompts if you press this soft- key ... The system will ... Scroll down through the available programs. Scroll up through the available programs. Select select the currently displayed program. Move the cursor to the left. Move the cursor to the right. - 1 move back through the availa...

  • Page 20

    System number plan/capacities note system type number plan/capacities related pro- gram • analog trunks 36 (sl1100) • bri trunk ports 36 (sl1100) • t1/pri trunk ports (sl1100) 60 (sl1100) • voipdb trunk ports (voipdb & memdb is re- quired. Need license to be max.) 16 (sl1100) did translation tables ...

  • Page 21

    System number plan/capacities note system type number plan/capacities related pro- gram speed dialing bins 0 ~ 999 13–02 speed dialing table-common 900 13–01–03 automated attendant vrs message numbers 1 ~ 100 25–06 conference conference circuits 32 : maximum (16 parties per conference) department an...

  • Page 22: 10  Concept of Slot Number

    System number plan/capacities note system type number plan/capacities related pro- gram level 4 (sb) pcpro/webpro user name : 9999 admin2 programming password users 8 extension numbers can be one to eight digits long. Refer to the flexible system numbering feature in the sl1000/sl1100 features and s...

  • Page 23: 1  Programming Your System

    Programming the sl1000/sl1100 s ection 1 programming your system the information contained in this chapter provides the information necessary to properly program your system. The programming blocks are organized into the following programming modes. Program number : program name program 10 : system ...

  • Page 24: 10-01 : Time and Date

    Program 10 : system configuration setup 10-01 : time and date level: sa description use program 10-01 : time and date to change the system time and date through system programming. Extension users can also dial service code 828 to change the time if allowed by an extension class of service. Input da...

  • Page 25: 10-02 : Location Setup

    Program 10 : system configuration setup 10-02 : location setup level: sa description use program 10-02 : location setup to define the location of the installed system. Input data item no. Item input data description default 01 country code dial (up to four digits) : 0 ~ 9, * , # enter the country co...

  • Page 26: 10-03 : Etu Setup

    Program 10 : system configuration setup 10-03 : etu setup level: in description use program 10-03 : etu setup to setup and confirm the basic configuration data for each unit. When changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatical...

  • Page 27

    Item no. Item input data description default 01 terminal type (b1) 0 = no setting 1 = multi-line telephone 10 = dss console 0 02 logical port number 0 = no setting 1 = multi-line telephone (1 ~ 72) 10 = dss console (1 ~ 12) 0 10 bottom option information 0 = none 4 = wha 0 12 multi-line telephone li...

  • Page 28

    Item no. Item input data description default 02 logical port number [0 : no setting] = 0 [1 : t-point] = 96 [2 : s-point] = 120 [3 ~ 5 : nw mode] = 0 [6 : s-point (leased line)] = 1 ~ 120 the starting port number of a bri line is displayed. Two logic ports are auto- matically assigned to a bri line....

  • Page 29

    For priu pkg setup isdn line number 01 ~ 30 item no. Item input data description default 01 isdn line mode 0 = no setting 1 = t-point 2 = s-point 6 = s-point (leased line) 1 02 logical port number [0 : no setting] = 0 [1 : t-point] = 1 ~ 126 (sl1000) 1 ~ 96 (sl1100) [2 : s-point] = 1 ~ 128 (sl1000) ...

  • Page 30

    Item no. Item input data description default 17 isdn ringback tone 0 = disable 1 = enable system can provide ring- back tone, by setting 10-03-17 is set to 1 : ena- ble. 0 18 type of number 0 = unknown 1 = international number 2 = national number 3 = network specific number 4 = subscriber number 5 =...

  • Page 31

    Item no. Item input data description default 06 number of ports 0 = auto 1 = 4 ports 2 = 8 ports 3 = 12 ports 4 = 16 ports 5 = 20 ports 0 for e1 pkg setup physical port number 01 ~ 30 item no. Item input data default 01 logical port number 1 ~ 126 (sl1000) 1 ~ 96 (sl1100) 0 02 number of channels 0 ~...

  • Page 32: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-10 program 10 : system configuration setup program 10

  • Page 33: 10-04 : Music On Hold Setup

    Program 10 : system configuration setup 10-04 : music on hold setup level: in description use program 10-04 : music on hold setup to set the music on hold (moh) source. For internal music on hold, the system can provide a service tone callers on hold or one of eleven synthesized selections. Input da...

  • Page 34: 10-06 : Isdn Bri Setup

    Program 10 : system configuration setup 10-06 : isdn bri setup level: in description use program 10-06 : isdn bri setup define the te1 selection and did mode for did callers when the bri feature is used. Input data slot no. 01 ~ 16 (sl1000) 01 ~ 09 (sl1100) isdn line no. 01 ~ 04 item no. Item input ...

  • Page 35: Description

    Program 10 : system configuration setup 10-07 : conversation recording resource level: in description use program 10-07 : conversation record resource to select the number of conference circuits to be used for conversation recording. Even if this program is set to ‘0', the telephone conversation rec...

  • Page 36: 10-08 : Pre-Ringing Setup

    Program 10 : system configuration setup 10-08 : pre-ringing setup level: in description use program 10-08 : pre-ringing setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk led flas...

  • Page 37: Description

    Program 10 : system configuration setup 10-09 : dtmf and dial tone circuit setup level: in description use program 10-09 : dtmf and dial tone circuit setup to allocate the circuits on the cpu for either dtmf receiving or dial tone detection. The cpu has 20 (sl1000) 16 (sl1100) circuits initially, an...

  • Page 38: Feature Cross Reference

    Item no. Item input data default 01 dtmf dial tone detection 0 = common use 1 = extension only 2 = trunk only resource 01 - 132 = 0 (common) (sl1000) resource 01 - 20 are basic resource (only use basic board) (sl1000) resource 21 - 36 are vmdb resource (only use basic board) (sl1000) resource 37 - 6...

  • Page 39: 10-12 : Cpu Network Setup

    Program 10 : system configuration setup 10-12 : cpu network setup level: sa description use program 10-12 : cpu network setup to setup the ip address, subnet-mask, and default gateway addresses. Caution! If any ip address or nic settings are changed, the system must be reset for the changes to take ...

  • Page 40

    Item no. Item input data description default 04 time zone 0~24 (0 = -12 hours and 24 = +12 hours) determine the offset from greenwich mean time (gmt) time. Then enter its respective value. For example, eastern time (us and canada) has a gmt offset of -5. The program data would then be 7 (0 = - 12, 1...

  • Page 42: 10-13 : In-Dhcp Server Setup

    Program 10 : system configuration setup 10-13 : in-dhcp server setup level: sa description use program 10-13 : in-dhcp server setup to setup the dhcp server built into the cpu. Input data item no. Item input data description default 01 dhcp server mode 0 = disable 1 = enable enable or disable the us...

  • Page 43: Description

    Program 10 : system configuration setup 10-14 : managed network setup level: sa description use program 10-14 : managed network setup to set up the range of the ip address which the dhcp server leases to a client. Input data item no. Item input data description default related pro- gram 01 the range...

  • Page 44: Description

    Program 10 : system configuration setup 10-15 : client information setup level: sa description use program 10-15 : client information setup to set up the client information when the dhcp server needs to assign a fixed ip address to clients. Input data client number 1 ~ 16 item no. Item input data de...

  • Page 45: Description

    Program 10 : system configuration setup 10-16 : option information setup level: sa description use program 10-16 : option information setup to set up the option given from the dhcp server to each client. The items highlighted in gray are read only and cannot be changed. Input data item no. Item inpu...

  • Page 46

    Item no. Item input data description default 10 ftp server address code number 0 ~ 255 set a ftp server ad- dress used for autocon- fig. 43 (fixed) sub code number 141 ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 0.0.0.0 11 config file name code number...

  • Page 47: Feature Cross Reference

    Item no. Item input data description default 23 lds server 4 code number 0 ~ 255 162 (fixed) ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 0.0.0.0 24 next server ip address ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223...

  • Page 48: Description

    Program 10 : system configuration setup 10-17 : h.323 gatekeeper setup level: sa description use program 10-17 : h.323 gatekeeper setup to set the h.323 gatekeeper information. Input data item no. Item input data description default 01 gatekeeper mode 0 = no gatekeeper 1 = automatic 2 = manual set i...

  • Page 49: Description

    Program 10 : system configuration setup 10-18 : h.323 alias address setup level: sa description use program 10-18 : h.323 alias address setup to set the alias address registered to the outside h.323 gatekeeper. Input data number of alias 1 ~ 6 item no. Item input data description default 01 alias ad...

  • Page 50: Description

    Program 10 : system configuration setup 10-19 : voipdb dsp resource selection level: in description use program 10-19 : voipdb dsp resource selection to define the criteria for each dsp resource on the voipdb unit. Input data dsp resource number 01 ~ 16 item no. Item input data description default 0...

  • Page 51: Description

    Program 10 : system configuration setup 10-20 : lan setup for external equipment level: in description use program 10-20 : lan setup for external equipment to define the tcp port/address/etc. For communicating to external equipment. Input data type of external equipment 1 = cti server 5 = smdr outpu...

  • Page 52: Description

    Program 10 : system configuration setup 10-23 : sip system interconnection setup level: sa description use program 10-23 : sip system interconnection setup to determine if the system is interconnected and define the ip address of another system, call control port number and alias address for sl1000/...

  • Page 53: Description

    Program 10 : system configuration setup 10-24 : daylight savings setup level: sa description use program 10-24 : daylight savings setup to set the options for daylight savings. As the telephone system is used globally, these settings define when the system should automatically adjust for daylight sa...

  • Page 54: Description

    Program 10 : system configuration setup 10-25 : h.323 gateway prefix setup level: sa description use program 10-25 : h.323 gateway prefix setup to set the gateway prefix registered to the outside gatekeeper. Input data item no. Item input data description default related program 01 gateway prefix en...

  • Page 55: Description

    Program 10 : system configuration setup 10-26 : ip system operation setup level: in description use program 10-26 : ip system operation setup to enable or disable the peer to peer feature for sip mlt and sip ip stations. Input data item no. Item input data description default 02 rtp forwarding mode ...

  • Page 56: Description

    Program 10 : system configuration setup 10-28 : sip system information setup level: sa description use program 10-28 : sip system information setup to set up basic sip trunking. Input data item no. Item input data description default 01 domain name up to 64 characters (ex. : userid@host- name.Domain...

  • Page 57: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-35 program 10

  • Page 58: Description

    Program 10 : system configuration setup 10-29 : sip server information setup level: sa description use program 10-29 : sip server information setup to define the sip proxy setup for outbound/ inbound. The 10-29 commands are not used in non-registration mode. If entries are made in program 10-29-xx f...

  • Page 59: Feature Cross Reference

    Item no. Item input data description default 12 domain name up to 64 characters this specifies the domain name of the sip server. No setting 13 proxy host name up to 48 characters this specifies the host name of the sip server. No setting 14 sip carrier choice (v1.5 changed) 0 ~ 26 1 = carrier a 2 =...

  • Page 60: Description

    Program 10 : system configuration setup 10-30 : sip authentication information setup level: in description use program 10-30 : sip authentication information setup to set the authentication options for sip trunks. Input data item no. Item input data description default 02 user name up to 64 characte...

  • Page 61: Description

    Program 10 : system configuration setup 10-33 : sip registrar/proxy information basic setup level: in description use program 10-33 : sip registrar/proxy information basic setup to set the registrar/proxy options for sip extensions. Input data item no. Item input data description default 01 registra...

  • Page 62: Description

    Program 10 : system configuration setup 10-36 : sip trunk registration information setup level: in description use program 10-36 : sip trunk registration information setup to set the sip trunk registration information. Input data register id 1 ~ 31 item no. Item input data description default 01 reg...

  • Page 63: 10-37 : Upnp Setup

    Program 10 : system configuration setup 10-37 : upnp setup level: in description use program 10-37 : upnp setup to set the upnp (universal plug and play) options for sip trunks. Input data item no. Item input data description default 01 upnp mode 0 = disable 1 = enable router must support upnp. 0 02...

  • Page 64: 10-39 : Fractional Setup

    Program 10 : system configuration setup 10-39 : fractional setup level: in description use program 10-39 : fractional setup to enable or disable the ability to use fractional t1 or pri. Input data item no. Item input data description default 01 fractional 0 = disable (when disa- bled the system will...

  • Page 65: Description

    Program 10 : system configuration setup 10-40 : ip trunk availability level: in description use program 10-40 : ip trunk availability to enable or disable the ability to use sip trunks and assign the number of ports if ip trunk is enabled. Input data slot number 0 item no. Item input data default 01...

  • Page 66: Description

    Program 10 : system configuration setup 10-42 : virtual loop back port setting level: in description use program 10-42 : virtual loop back port setting to set the data for the virtual loop back port. Input data item no. Item input data default 01 number of loop back ports 0 ~ 30 (0 = no setting) 0 0...

  • Page 67: Description

    Program 10 : system configuration setup 10-45 : ip routing table setup level: sa description use program 10-45 : ip routing table setup to set up the ip routing table. Input data routing table number 001 ~ 100 item no. Item input data default 01 network address 0.0.0.0 ~ 126.255.255.254 128.0.0.0 ~ ...

  • Page 68: Description

    Program 10 : system configuration setup 10-46 : dr700 server information setup level: in description use program 10-46 : dr700 server information setup to set up the information of dr700 server. Input data item no. Item input data description default related program 01 register mode 0 = normal 1 = a...

  • Page 69: Feature Cross Reference

    Item no. Item input data description default related program 13 subscribe ses- sion port 0 ~ 65535 5081 14 nat mode 0 = off 1 = on when the system controls the sip multiline terminal via the nat router, this system data is set to on. 0 conditions none feature cross reference none issue 3.01 sl1000/s...

  • Page 70: Description

    Program 10 : system configuration setup 10-47 : terminal license server information setup level: in description use program 10-47 : terminal license server information setup to setup the information of terminal license server. Input data item no. Item input data description default 01 register port ...

  • Page 71: 10-48 : License Activation

    Program 10 : system configuration setup 10-48 : license activation level: in description use program 10-48 : license activation to turn on the license issued from the license server. Input data item no. Item input data default 01 software key code 20-digit character no setting 02 activation code 8-d...

  • Page 72: Description

    Program 10 : system configuration setup 10-49 : license file activation level: in description use program 10-49 : license file activation to enable the command to save the license file via cf card which is issued from the license server. Input data item no. Item input data default 01 save license fi...

  • Page 73: 10-50 : License Information

    Program 10 : system configuration setup 10-50 : license information level: in description use program 10-50 : license information to confirm license information that is stored in a system. Input data feature code number 000 ~ 9999 item no. Item input data default 01 license name read only: character...

  • Page 74: Description

    Program 10 : system configuration setup 10-51 : pri/t1/e1 selection of pri level: in description use program 10-51 : pri/t1/e1 selection of pri to select whether the unit works as pri, t1 or e1. Input data slot number 01 ~ 16 (v1.5 changed) (sl1000) 01 ~ 09 (sl1100) item no. Item input data descript...

  • Page 75: Description

    Program 10 : system configuration setup 10-52 : free/demo license information level: in description use program 10-52 : free/demo license information to display information on free of charge/demo license. Input data item no. Item input data default 01 remaining days of free/demo li- cense read only:...

  • Page 76: 10-58 : Network Address

    Program 10 : system configuration setup 10-58 : network address level: in (this program is available for v1.5 or higher) description use program 10-58 : network address to set the local network address when the sip multiline terminal connects the system via a local router. Input data area table 1 ~ ...

  • Page 77: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-55 program 10

  • Page 78: Description

    Program 10 : system configuration setup 10-60 : audio port setup (sl1100) level: in description use program 10-60 : audio port setup to defines which audio port on the 084m packages are used for bgm/external moh. Input data audio port number 1 = bgm 2 = external moh item no. Item input data descript...

  • Page 79: 10-61 : Relay Port Setup

    Program 10 : system configuration setup 10-61 : relay port setup level: in description use program 10-61 : relay port setup to defines the relay port type on the 408m (sl1000) 084m (sl1100). Input data relay port no. 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Item input data default 01 relay type 0 = no...

  • Page 80: 10-62 : Netbios Setting

    Program 10 : system configuration setup 10-62 : netbios setting level: in description use 10-62 : netbios setting to set the data of netbios. Input data item no. Item input data description default 01 netbios mode 0 = disabled 1 = enabled 1 02 netbios name maximum 15 characters please avoid using sp...

  • Page 81: 10-63 : Dhcp Client Setting

    Program 10 : system configuration setup 10-63 : dhcp client setting level: in description use 10-63 : dhcp client setting to set the data of dhcp client. Input data item no. Item input data description default 01 dhcp client mode 0 = disabled 1 = enabled if you are using ip phones/trunks it is rec- ...

  • Page 82: 11-01 : System Numbering

    Program 11 : system numbering 11-01 : system numbering level: in description use program 11-01 : system numbering to set the system numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other extensions and features...

  • Page 83

    Dial types dial type descrip- tion related program note 1 service code 11-10 : service code setup (for system administrator) on page 2-71 11-11 : service code setup (for setup/entry operation) on page 2-75 11-12 : service code setup (for service access) on page 2-80 11-14 : service code setup (for h...

  • Page 84

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 21 0 0 22 0 0 23 0 0 24 0 0 25 0 0 26 0 0 27 0 0 28 ...

  • Page 85

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 5x 4 2 51 0 0 52 0 0 53 0 0 54 0 0 55 0 0 56 0 0 57 ...

  • Page 86

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 8x 3 1 81 0 0 82 0 0 83 0 0 84 0 0 85 0 0 86 0 0 87 ...

  • Page 87: Feature Cross Reference

    Dial types : 1 = service code, 2 = extension number, 3 = trunk access, 4 = special trunk access, 5 = operator access, 6 = flexible routing, 9 = dial extension analyze, 0 = not used dialed number of digits required dial type default new default new 0# 0 0 * x 4 4 * 1 0 0 * 2 0 0 * 3 0 0 * 4 0 0 * 5 0...

  • Page 88: 11-02 : Extension Numbering

    Program 11 : system numbering 11-02 : extension numbering level: in description use program 11-02 : extension numbering to set the extension number. The extension number can have up to four digits (sl1000) eight digits (sl1100). The first/second digit (s) of the number should be assigned in program ...

  • Page 89: Description

    Program 11 : system numbering 11-04 : virtual extension numbering level: in description use program 11-04 : virtual extension numbering to define the virtual extension numbers. The extension number can have up to four (sl1000) eight (sl1100) digits. The first/second digit (s) of the number should be...

  • Page 90: Description

    Program 11 : system numbering 11-07 : department group pilot numbers level: in description use program 11-07 : department group pilot numbers to assign a pilot number to each department group set up in program 16-02. The pilot number is the number users dial for department calling and department ste...

  • Page 91: 11-09 : Trunk Access Code

    Program 11 : system numbering 11-09 : trunk access code level: in description use program 11-09 : trunk access code to assign the trunk access code. The trunk access code can be set from 1 ~ 4 digits which is defined to type 3 and 4 in program 11-01. This is the code extension users dial to access a...

  • Page 92: Feature Cross Reference

    Item no. Item input data description default related program 02 2nd trunk route access code dial (up to four digits) use this program to define addition- al trunk access codes. When a user dials the alternate trunk route access code, the sys- tem routes their call to the alternate trunk route. No se...

  • Page 93: Description

    Program 11 : system numbering 11-10 : service code setup (for system administrator) level: in description use program 11-10 : service code setup (for system administrator) to customize the service codes for the system administrator. You can customize additional service codes in programs 11-11 ~ 11-1...

  • Page 94

    Item no. Item input data description default related program 11 entry credit for toll restriction 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt 774 12 night mode switching for other group 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 dig...

  • Page 95

    Item no. Item input data description default related program 34 set caller id re- fuse 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 748 14-01-27 20-07-25 35 dial-in mode switching 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit...

  • Page 96: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-74 program 11 : system numbering program 11.

  • Page 97: Description

    Program 11 : system numbering 11-11 : service code setup (for setup/entry operation) level: in description use program 11-11 : service code setup (for setup/entry operation) to customize the service codes which are used for registration and setup. You can customize additional service codes in progra...

  • Page 98

    Item no. Item input data description default related program 10 cancel all mes- sages waiting 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 873 11 cancel message waiting 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) t...

  • Page 99

    Item no. Item input data description default related program 25 automatic trans- fer setup for each extension group 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 702 20-11-17 24-05 26 automatic trans- fer cancellation for each exten- sion group 0~9,...

  • Page 100

    Item no. Item input data description default related program 41 tandem ringing 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 744 15-07 30-03 43 headset mode switching 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) term...

  • Page 101: Feature Cross Reference

    Item no. Item input data description default related program 60 call forward to attendant/no an- swer 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 797 15-01-09 62 adjust of head- set ring volume 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # max...

  • Page 102: Description

    Program 11 : system numbering 11-12 : service code setup (for service access) level: in description use program 11-12 : service code setup (for service access) to customize the service codes which are used for service access. You can customize additional service codes in programs 11-10, 11-11, and 1...

  • Page 103

    Item no. Item input data description default related program 08 barge-in 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 810 09 change to stg (department group) all ring 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) ter...

  • Page 104

    Item no. Item input data description default related program 23 meet-me answer in same paging group 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 863 31-02-01 24 combined pag- ing 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit ...

  • Page 105

    Item no. Item input data description default related program 38 general purpose indication 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt 883 15-07-56 15-07-57 40 station speed di- aling (v2.0 add- ed) (sl1000) 0~9, * , # maximum of 4 digit terminal:...

  • Page 106: Feature Cross Reference

    Item no. Item input data description default related program 57 tandem trunk- ing 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt #8 58 transfer into conference 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: ml...

  • Page 107: Description

    Program 11 : system numbering 11-14 : service code setup (for hotel) level: in description use program 11-14 : service code setup (for hotel) to customize the service codes which are used with the hotel/motel feature. You can customize additional service codes in programs 11-10 ~ 11-12, 11-15 and 11...

  • Page 108: Feature Cross Reference

    Item no. Item input data description default 09 set room to room call restriction 0~9, * , # maximum of 4 digit (sl1000) 0~9, * , # maximum of 8 digit (sl1100) terminal: mlt, slt determine what the service code should be for an internal party to set room to room call restriction. 735 10 cancel room ...

  • Page 109: Access)

    Program 11 : system numbering 11-15 : service code setup, administrative (for special access) level: in description use program 11-15 : service code setup, administrative (for special access) to customize the special access service codes which are used by the administrator in the hotel/motel feature...

  • Page 110: Feature Cross Reference

    Conditions none feature cross reference none sl1000/sl1100 issue 3.01 2-88 program 11 : system numbering program 11.

  • Page 111: Description

    Program 11 : system numbering 11-16 : single digit service code setup level: in description use program 11-16 : single digit service code setup to customize the one-digit service codes used when a busy or ring back signal is heard. You can customize additional service codes in programs 11-10 ~ 11-15...

  • Page 112: Description

    Program 11 : system numbering 11-19 : remote conference pilot number setup level: in description use program 11-19 : remote conference pilot number setup to assign the pilot number to be used for the remote conference. This is the number that outside parties will call in order to connect to a confer...

  • Page 113: Description

    Program 11 : system numbering 11-20 : dial extension analyze table level: in description use program 11-20 : dial extension analyze table to define the dial type based on three or more digits. This program is relevant only if digits in 11-01-01 are set to 9 (dial extension analyze). Input data dial ...

  • Page 114: Description

    Program 12 : night mode setup 12-01 : night mode function setup level: in description use program 12-01 : night mode function setup to set up the night mode options. Refer to the following chart for a description of each option, its range and default setting. Input data item no. Item input data desc...

  • Page 115: Description

    Program 12 : night mode setup 12-02 : automatic night service patterns level: sa description use program 12-02 : automatic night service patterns to define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The dai...

  • Page 116: Feature Cross Reference

    Time setting 01 : 00 : 00 to 00 : 00 mode 2 (night) default time pattern 1 set time number start time end time mode 01 0000 0800 2 02 0800 1700 1 03 1700 0000 2 04 0000 0000 1 : : : : 20 0000 0000 1 time pattern 2 set time number start time end time mode 01 0000 0000 2 02 0000 0000 1 : : : : 20 0000...

  • Page 117: Description

    Program 12 : night mode setup 12-03 : weekly night service switching level: sa description use program 12-03 : weekly night service switching to define a weekly schedule of night-switch settings. 21-02 : trunk group routing for extensions input data night mode service group number 01 ~ 04 item no. I...

  • Page 118: Description

    Program 12 : night mode setup 12-04 : holiday night service switching level: sa description use program 12-04 : holiday night service switching to define a yearly schedule of holiday night- switch settings. This schedule is used for the setting of special days when the company is expected to be clos...

  • Page 119: Description

    Program 12 : night mode setup 12-05 : night mode group assignment for extensions level: in description use program 12-05 : night mode group assignment for extensions to a assign day/night mode group for each extension. Input data extension number up to four digits (sl1000) up to eight digits (sl1100...

  • Page 120: Description

    Program 12 : night mode setup 12-06 : night mode group assignment for trunks level: in description use program 12-06 : night mode group assignment for trunks to assign a day/night mode group for each trunk port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input d...

  • Page 121: Description

    Program 12 : night mode setup 12-07 : text data for night mode level: in description use program 12-07 : text data for night mode to make an original text message which is displayed on an lcd of multiline telephone in each mode. Input data night mode service group number 01 ~ 04 day/night mode 1 ~ 8...

  • Page 122: Feature Cross Reference

    Conditions none feature cross reference • night service sl1000/sl1100 issue 3.01 2-100 program 12 : night mode setup program 12.

  • Page 123: Description

    Program 12 : night mode setup 12-08 : night mode service range level: sa description use program 12-08 : night mode service range to define the changing range of toggle key for each day/night mode. Input data night mode service group number 01 ~ 04 item no. Item input data description default 01 ran...

  • Page 124: Description

    Program 13 : abbreviated dialing 13-01 : speed dialing option setup level: in description use program 13-01 : speed dialing option setup to define the speed dialing functions. Input data item no. Item input data description default related program 01 speed dialing auto outgoing call mode 0 = trunk o...

  • Page 125: Description

    Program 13 : abbreviated dialing 13-02 : group speed dialing bins level: in description use program 13-02 : group speed dialing bins to define the range of bin numbers to be used by each speed dialing group. (refer to 13-03 : speed dialing group assignment for extensions on page 2-104 .) input data ...

  • Page 126: Description

    Program 13 : abbreviated dialing 13-03 : speed dialing group assignment for extensions level: in description use program 13-03 : speed dialing group assignment for extensions to assign speed dialing group for each extension. There are 32 available speed dialing groups. Input data extension number up...

  • Page 127: Description

    Program 13 : abbreviated dialing 13-04 : speed dialing number and name level: sb description use program 13-04 : speed dialing number and name to store speed dialing data in the speed dialing areas. This program is also used to define the names assigned to the speed dialing numbers. Input data speed...

  • Page 128: Feature Cross Reference

    Item no. Item input data description default related program 04 transfer destina- tion number if transfer mode is (refer to 13-04-03) : 1 = internal dial mode 1 ~ 9, 0, * , #, p, r, @ (maximum 36 charac- ters) 2 = incoming ring group 0 ~ 25 (irg number) p = pause r = recall @ = additional digits whe...

  • Page 129: Description

    Program 13 : abbreviated dialing 13-05 : speed dial trunk group level: sb description use program 13-05 : speed dialing trunk group to define the trunk group to be seized for each speed dialing number. If this program has an entry of 0 (no setting), then seizing a line follows the trunk access group...

  • Page 130: Description

    Program 13 : abbreviated dialing 13-06 : speed dial number and name level: sb description use program 13-06 : speed dial number and name to set up the dial number and name of each speed dial number. Input data extension number up to 4 digits (sl1000) up to 8 digits (sl1100) speed dial number 01 ~ 20...

  • Page 131: Description

    Program 13 : abbreviated dialing 13-11 : abbreviated dial group name level: sb description use program 13-11 : abbreviated dial group name to set the name of abbreviated dial group name. Input data group number 01 ~ 32 item no. Item input data default 01 group name up to 12 characters 1 = abb : grou...

  • Page 132: Description

    Program 14 : trunk, basic setup 14-01 : basic trunk data setup level: in description use program 14-01 : basic trunk data setup to set the basic options for each trunk port. Refer to the chart below for a description of each option, its range and default setting. Input data trunk port number 001 ~ 1...

  • Page 133

    Item no. Item input data description default related program 09 private line 0 = disable private line (normal) 1 = enable private line (private line) 1 10 dtmf tones for outgoing calls 0 = disable (no) 1 = enable (yes) use this option to enable (1) or disa- ble (0) dtmf tones for outgoing trunk call...

  • Page 134

    Item no. Item input data description default related program 23 least cost rout- ing 0 = lcr off 1 = lcr on 2 = lcr on (cost cen- ter code only) 0 24 trunk-to-trunk outgoing caller id through mode 0 = disable (caller id not forwarded out.) 1 = enable (caller id is forwarded out.) enable (1) or disab...

  • Page 135: Feature Cross Reference

    Item no. Item input data description default related program 41 incoming caller name usage (v2.0 added) 0 = use 1 = ignore this program will determines that the caller name information from the network is valid or not. If the pro- gram is set to 1, the caller name in- formation the network provides ...

  • Page 136: Description

    Program 14 : trunk, basic setup 14-02 : analog trunk data setup level: in description use program 14-02 : analog trunk data setup to set the basic options for each analog trunk port. Refer to the table below for a description of each option, its range and default setting. Input data trunk port numbe...

  • Page 137

    Item no. Item input data description default related program 07 dp to dtmf con- version options 0 = automatic 1 = automatic and manual 2 = manual determine how a user can convert a dial pulse (dp) call to a dtmf call. For each trunk, set the type of dp to dtmf conversion required. There are three co...

  • Page 138: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-116 program 14 : trunk, basic setup program 14.

  • Page 139: 14-04 : Behind Pbx Setup

    Program 14 : trunk, basic setup 14-04 : behind pbx setup level: in description use program 14-04 : behind pbx setup to indicate if the trunk is installed behind a pbx. There is one item for each mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) day/night mode 1 ~ 8 item no. It...

  • Page 140: 14-05 : Trunk Group

    Program 14 : trunk, basic setup 14-05 : trunk group level: in description use program 14-05 : trunk group to assign trunks to trunk groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in the...

  • Page 141: 14-06 : Trunk Group Routing

    Program 14 : trunk, basic setup 14-06 : trunk group routing level: in description use program 14-06 : trunk group routing to set up an outbound routing table for the trunk groups you assigned in program 14-05. When a user dial 9, the system routes their calls in the order (priority) specified. For e...

  • Page 142: Feature Cross Reference

    Default route no. Order data route 1 1 1 (trunk group 1) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) route 2 1 0 (not specified) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) : 1 0 (not specified) 2 0 (not specified) 3 0 (not specified) 4 0 (not specified) route 25 1 0 ...

  • Page 143: Description

    Program 14 : trunk, basic setup 14-07 : trunk access map setup level: in description use program 14-07 : trunk access map setup to set up the trunk access maps. This sets an extension access options for trunks. For example, an extension can place only outgoing calls on trunks to which it has outgoin...

  • Page 144: Feature Cross Reference

    Access map no. Trunk port no. Default : 1 0 (no access) 2 0 (no access) : : 126 (sl1000) 096 (sl1100) 0 (no access) 126 (sl1000) 096 (sl1100) 1 0 (no access) 2 0 (no access) : : 126 (sl1000) 096 (sl1100) 0 (no access) conditions none feature cross reference • central office calls, answering • centra...

  • Page 145: Description

    Program 14 : trunk, basic setup 14-08 : music on hold source for trunks level: in description use program 14-08 : music on hold source for trunks to define a music on hold source for a trunk as coi port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data desc...

  • Page 146: Description

    Program 14 : trunk, basic setup 14-09 : conversation recording destination for trunks level: in description use program 14-09 : conversation recording destination for trunks to set the conversation recording destination for each trunk. If both programs 14-09 and 15-12 define a destination, the desti...

  • Page 147: Description

    Program 14 : trunk, basic setup 14-11 : id setup for ip trunk level: in description use program 14-11 : id setup for ip trunk to set the id of each ip trunk. This program refers to incoming and outgoing ip trunk calls. The id is sent on an outgoing ip trunk call. This program is used only for h.323....

  • Page 148: Description

    Program 14 : trunk, basic setup 14-12 : sip register id setup for ip trunk level: in description use program 14-12 : sip register id setup for ip trunk to define the sip register id for ip trunks. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default 01 ...

  • Page 149: Description

    Program 14 : trunk, basic setup 14-15 : isdn call forward method level: in description use program 14-15 : isdn call forward method to assign the activation of call deflection/call rerouting feature. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default ...

  • Page 150: Description

    Program 15 : extension, basic setup 15-01 : basic extension data setup level: sa description use program 15-01 : basic extension data setup to define the basic settings for each extension. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no. Item input data...

  • Page 151: Feature Cross Reference

    Item no. Item input data description default related program 13 special ringtone choice (v2.0 add- ed) 0 = incoming extension ring tone (sl1000) 1 = tone pattern 1 (sl1000) 2 = tone pattern 2 (sl1000) 3 = tone pattern 3 (sl1000) 4 = tone pattern 4 (sl1000) 5 = tone pattern 5 (sl1000) 6 = tone patter...

  • Page 152: Description

    Program 15 : extension, basic setup 15-02 : multiline telephone basic data setup level: in description use program 15-02 : multiline telephone basic data setup to set up various multiline telephone options. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item n...

  • Page 153

    Item no. Item input data description default related program 02 trunk ring tone 1 = tone pattern 1 (dr300)/ high (dr700) (sl1000) 2 = incoming external ring tone/ medium (dr700) (sl1000) 3 = tone pattern 3 (dr300)/ low (dr700) (sl1000) 4 = tone pattern 4 (dr300)/ melody 1 (dr700) (sl1000) 5 = tone p...

  • Page 154

    Item no. Item input data description default related program 03 extension ring tone 1 = tone pattern 1 (dr300)/ high (dr700) (sl1000) 2 = incoming external ring tone/ medium (dr700) (sl1000) 3 = tone pattern 3 (dr300)/ low (dr700) (sl1000) 4 = tone pattern 4 (dr300)/ melody 1 (dr700) (sl1000) 5 = to...

  • Page 155

    Item no. Item input data description default related program 11 callback auto- matic answer 0 = off 1 = on use this option to enable or disable automatic answer of calls recalling to a station. For example, if a trans- fer recall or hold recall is ringing back to a station, the following hap- pens: ...

  • Page 156

    Item no. Item input data description default related program 23 speed dial pre- view mode 0 = preview 1 = outgoing immedi- ately this option defines how a speed dial key functions when pressed. If set to preview (0), the speed dial number can be previewed before dialing. If set to outgoing immediate...

  • Page 157

    Item no. Item input data description default related program 42 incoming off- hook ring setup 0=speaker off-hook ring 1=headset off-hook ring 0 11-11-37 11-11-62 15-02-12 15-02-41 43 headset ring duration 0=no switch to speak- er ring 1=10 sec 2=20 sec 3=30 sec 4=40 sec 5=50 sec 6=1 minute 0 11-11-6...

  • Page 158: Feature Cross Reference

    Item no. Item input data description default related program 69 mute operation on handsfree (3.0 added) 0 = do not change mute status 1 = start with enabled mute 2 = start with muted mute 0 70 mute key opera- tion (v2.0 added) 0 = enabled (active) 1 = disabled this program determines whether the mut...

  • Page 159: Description

    Program 15 : extension, basic setup 15-03 : single line telephone basic data setup level: in description use program 15-03 : single line telephone basic data setup to set up various single line telephone options. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) ...

  • Page 160

    Item no. Item input data description default related program 09 caller id func- tion - for exter- nal module 0 = disable (caller id not displayed.) 1 = enable (caller id is displayed.) enable (1) or disable (0) the caller id fsk signal for an external caller id module or a 3rd party vendor tel- epho...

  • Page 161: Feature Cross Reference

    Conditions none feature cross reference • single line telephones issue 3.01 sl1000/sl1100 programming manual 2-139 program 15.

  • Page 162: Description

    Program 15 : extension, basic setup 15-05 : ip telephone terminal basic data setup level: in description use program 15-05 : ip telephone terminal basic data setup to set up the basic settings for an ip telephone. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100)...

  • Page 163

    Item no. Item input data description default related program 18 ip duplication al- lowed group 0 = not used 1 = group 1 2 = group 2 3 = group 3 4 = group 4 5 = group 5 6 = group 6 7 = group 7 8 = group 8 9 = group 9 10 = group 10 if there is an adapter that has one ip address coming into it but has ...

  • Page 164: Feature Cross Reference

    Item no. Item input data description default related program 40 calling name dis- play info via trunk for stand- ard sip 0 = both name and number 1 = name only 2 = number only 3 = none 0 41 time zone(hour) 0 ~ 24 (- 12 ~ + 12 hour) 12 42 time zone(mi- nute) 0 ~ 120 (- 60 ~ + 60 minute) 60 43 video m...

  • Page 165: Description

    Program 15 : extension, basic setup 15-06 : trunk access map for extensions level: in description use program 15-06 : trunk access map for extensions to define the trunk access map for each extension. An extension can place only outgoing calls on trunks to which it has outgoing access. Use program 1...

  • Page 166: Description

    Program 15 : extension, basic setup 15-07 : programmable function keys level: sa description use program 15-07 : programmable function keys to assign functions to a multiline terminal line keys. For certain functions, you can append data to the key basic function. For example, the function 26 append...

  • Page 167

    Table 2-2 function number list [1] normal function code (00 ~ 99, #00 ~ #99) (service code 851) function number function additional data led indication note 01 dss/one-touch extension number or any numbers (up to 36 digits) on (red) : dss ext. Busy off : dss ext. Idle, dnd external, dnd transfer, cf...

  • Page 168

    Function number function additional data led indication note 26 call pickup for specified group call pickup group number (01 ~ 32) none 27 speed dial - common/private speed dial number (common / private) none 28 speed dial - group speed dial number (group) none 29 repeat redial fast blink (red) : re...

  • Page 169

    Function number function additional data led indication note 54 external call for- ward by door box on (red) : setup 55 extension name change none 56 general purpose led operation 001 ~ 100 : (red) on off 001 ~ 100 : (red) on off 57 general purpose led indication 001 ~ 100 : (red) on off 001 ~ 100 :...

  • Page 170

    Function number function additional data led indication note 80 tandem ringing 1 = set 0 = cancel exten- sion number to tan- dem ring on (red) : master side slow blink : slave side 81 automatic trans- fer to transfer key trunk line no. (001-126) (sl1000) trunk line no. (001-096) (sl1100) off : cance...

  • Page 171

    Func- tion number function additional da- ta led indication note * 01 trunk key trunk number (001 ~ 126) (sl1000) trunk number (001 ~ 096) (sl1100) fast blink (green) : incoming(own)/transferring(own)/ recall(own) (sl1000) fast blink (red) : incoming(other) (sl1000) (125msec:on / 125msec:off / 125ms...

  • Page 172

    Pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern #7 1 1 1 1 1 1 0 1 0 1 111 200 400 600 800 10...

  • Page 173: Feature Cross Reference

    Led pattern 0:[o ff] led pattern 1:[fl: o n(500m s)/off(500m s)] o n o ff o n o ff led pattern 2:[w k: o n(250m s)/off(250m s)] o n o ff led pattern 3:[rw : o n(125m s)/off(125m s)] o n o ff led pattern 4:[ir: o n(125m s)/off(125m s)/ o n(125m s)/off(625m s)] led pattern 5:[il o n(875m s)/off(125m s...

  • Page 174: Description

    Program 15 : extension, basic setup 15-08 : incoming virtual extension ring tone setup level: in description use program 15-08 : incoming virtual extension ring tone setup to assign a ring tone range (0 ~ 4) to incoming virtual extensions assigned to a virtual extension key (program 15-07). If you e...

  • Page 175: Feature Cross Reference

    Incoming signal frequency pattern type frequency 1 frequency 2 modulation pattern 4 high middle low 2000 hz 1400 hz 1100 hz 760 hz 660 hz 540 hz 8 hz 8 hz 8 hz internal incoming sig- nal frequency high middle low 1100 hz 660 hz 520 hz 1400 hz 760 hz 660 hz 8 hz 8 hz 8 hz conditions none feature cros...

  • Page 176: Description

    Program 15 : extension, basic setup 15-09 : virtual extension ring assignment level: sa description use program 15-09 : virtual extension ring assignment to assign the ringing options for an extension virtual extension key or virtual extension group answer key which is defined in program 15-07. You ...

  • Page 177: Description

    Program 15 : extension, basic setup 15-10 : incoming virtual extension ring tone order setup level: sa description use program 15-10 : incoming virtual extension ring tone order setup to set the priority (1 ~ 4) for the virtual extension ring tones set in program 15-08. When virtual extension calls ...

  • Page 178: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-156 program 15 : extension, basic setup program 15.

  • Page 179: Description

    Program 15 : extension, basic setup 15-11 : virtual extension delayed ring assignment level: sa description use program 15-11 : virtual extension delayed ring assignment to assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in progra...

  • Page 180: Description

    Program 15 : extension, basic setup 15-12 : conversation recording destination for extensions level: in description use program 15-12 : conversation recording destination for extensions to set the conversation recording destination for each extension. If both programs 14-09 and 15-12 define a destin...

  • Page 181: 15-13 : Loop Keys

    Program 15 : extension, basic setup 15-13 : loop keys level: in description use program 15-13 : loop keys to assign the loop key data for each keyset terminal. Loop keys can be incoming, outgoing or both ways. Outgoing loop keys use the entry in item 1. Incoming loop keys use the entry in item 2. Bo...

  • Page 182: Description

    Program 15 : extension, basic setup 15-14 : programmable one-touch keys level: sb (this program is available for v2.0 or higher) (sl1000) description use program 15-14 : programmable one-touch keys to define the one-touch key data for each multiline terminal. For each sl1000/sl1100 wireless telephon...

  • Page 183: Description

    Program 15 : extension, basic setup 15-16 : sip register id setup for extension level: in description use program 15-16 : sip register id setup for extension to define the sip register id for extensions. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) item no. ...

  • Page 184: Description

    Program 15 : extension, basic setup 15-17 : co message waiting indication level: in description use program 15-17 : co message waiting indication to set the message waiting led flash assignment on each co line. Input data extension number including virtual extensions up to four digits (sl1000) up to...

  • Page 185: Description

    Program 15 : extension, basic setup 15-18 : virtual extension key enhanced options level: in description use program 15-18 : virtual extension key enhanced options to define the operation when a virtual extension key is pressed. Input data extension number including virtual extensions up to four dig...

  • Page 186: Feature Cross Reference

    Condition • if a dil rings a virtual extension, the virtual extension key operation mode must be set to 1. Feature cross reference none sl1000/sl1100 issue 3.01 2-164 program 15 : extension, basic setup program 15.

  • Page 187: Description

    Program 15 : extension, basic setup 15-22 : mobile extension setup level: in description use program 15-22 : mobile extension setup to set the system information for the mobile extension feature. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input d...

  • Page 188: Description

    Program 15 : extension, basic setup 15-24 : registration of standard sip terminal level: in (this program is available for v1.5 or higher) description use program 15-24 : registration of standard sip terminal to register data in the standard sip terminal where register is not used. Input data item n...

  • Page 189: Description

    Program 15 : extension, basic setup 15-28 : trunk incoming ring tone of extension setup level: in (this program is available for v1.5 or higher) description use program 15-28 : trunk incoming ring tone of extension setup to define the ringing tone for each trunk port of extension. Input data extensi...

  • Page 190: Feature Cross Reference

    Conditions none feature cross reference none sl1000/sl1100 issue 3.01 2-168 program 15 : extension, basic setup program 15.

  • Page 191: Description

    Program 16 : department group setup 16-01 : department group basic data setup level: in description use program 16-01 : department group basic data setup to set the function mode for each department group. There are 32 available department groups. Input data department group number 1 ~ 32 item no. I...

  • Page 192: Feature Cross Reference

    Item no. Item input data description default 10 subnet mask 128.0.0.0

  • Page 193: Description

    Program 16 : department group setup 16-02 : department group assignment for extensions level: in description use program 16-02 : department group assignment for extensions to set the department groups. The system uses these groups (32 department groups) for department calling. Assign pilot numbers t...

  • Page 194: Description

    Program 16 : department group setup 16-03 : secondary department group level: in description use program 16-03 : secondary department group to set a second department group for extensions. Up to 16 extensions can be assigned per a department group. There are 32 available department groups. Input dat...

  • Page 195: Description

    Program 16 : department group setup 16-04 : call restriction between department groups level: in description use program 16-04 : call restriction between department groups to set internal calls between members of different department (station) groups that can be restricted on a per group basis. Each...

  • Page 196: 20-01 : System Options

    Program 20 : system option setup 20-01 : system options level: in description use program 20-01 : system options to set various system options. Input data item no. Item input data description default related program 01 operator access mode 0 = step call 1 = circular use this program to set up priori...

  • Page 197: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-175 program 20

  • Page 198: Description

    Program 20 : system option setup 20-02 : system options for multiline telephones level: in description use program 20-02 : system options for multiline telephones to set various system options for multiline telephones. Input data item no. Item input data description default related program 01 trunk ...

  • Page 199

    Item no. Item input data description default related program 05 headset busy mode 0 = no (disable) 1 = yes (enable) set the condi- tions under which a head- set extension is busy to in- coming callers. 0 20-09-07 06 pre-selection time 0 ~ 64800 seconds when a multi- line terminal user preselects a l...

  • Page 200: Feature Cross Reference

    Item no. Item input data description default related program 11 handsfree micro- phone control 0 = off 1 = on use this option to control the setting for mul- tiline terminal handsfree mi- crophone after being discon- nected and re- connected. If set to 0, the microphone is always off when the ter- m...

  • Page 201: Description

    Program 20 : system option setup 20-03 : system options for single line telephones level: in description use program 20-03 : system options for single line telephones to set up various options for single line telephones. Input data item no. Item input data description default related program 01 slt ...

  • Page 202: Feature Cross Reference

    Item no. Item input data description default related program 06 headset ringing start time (for slt) 0 ~ 64800 seconds define the headset ringing start time. After this time expires from the time when a single line telephone is off-hook, the system sets the single line telephone to headset ringing m...

  • Page 203: Description

    Program 20 : system option setup 20-04 : system options for virtual extensions level: in description use program 20-04 : system options for virtual extensions to set up various system options for virtual extensions. There are 50 available virtual extension ports. Input data item no. Item input data ...

  • Page 204: Description

    Program 20 : system option setup 20-05 : system options for charging cost service level: in description use program 20-05 : system options for charging cost service to defines the system options for charging cost service. Input data item no. Item input data default 04 setting of charge cost per unit...

  • Page 205: Description

    Program 20 : system option setup 20-06 : class of service for extensions level: in description use program 20-06 : class of service for extensions to assign a class of service (cos) to an extension. There are 15 classes of service that can be assigned. To specify the options in each class of service...

  • Page 206: Description

    Program 20 : system option setup 20-07 : class of service options (administrator level) level: in description use program 20-07 : class of service options (administrator level) to define the administrator service availability for each extension class of service (cos). Input data class of service num...

  • Page 207: Feature Cross Reference

    Item no. Item input data description default related program 15 vrs general message record/ delete 0 = off 1 = on turns off or on an extension user ability to dial service code 712 and record, listen to, or erase the gener- al message. Cos 1 ~ 15 = 1 11-10-22 18 smdr printout accumulated ex- tension...

  • Page 208: Description

    Program 20 : system option setup 20-08 : class of service options (outgoing call service) level: in description use program 20-08 : class of service options (outgoing call service) to define the outgoing call feature availability for each extension class of service (cos). Input data class of service...

  • Page 209: Feature Cross Reference

    Item no. Item input data description default related program 13 isdn clip 0 = off (when set to off the system will not send any outbound calling party informa- tion.) 1 = on (when set to on the system will send calling party informa- tion for the station or trunk.) determines if the isdn calling lin...

  • Page 210: Description

    Program 20 : system option setup 20-09 : class of service options (incoming call service) level: in description use program 20-09 : class of service options (incoming call service) to define the incoming call feature availability for each extension class of service (cos). Input data class of service...

  • Page 211: Feature Cross Reference

    Item no. Item input data description default related program 09 deny collect call receiving 0 = off 1 = on cos 01 ~ 15 = 0 13 dnd active while ringing (v3.0 added) 0 = immediate 1 = next call when set to 0, and if set dnd dur- ing an incoming call, the call for the terminal stops immediately. When s...

  • Page 212: Description

    Program 20 : system option setup 20-10 : class of service options (answer service) level: in description use program 20-10 : class of service options (answer service) to define the answer feature availability for each extension class of service (cos). Input data class of service number 01 ~ 15 item ...

  • Page 213: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-191 program 20

  • Page 214: Description

    Program 20 : system option setup 20-11 : class of service options (hold/transfer service) level: in description use program 20-11 : class of service options (hold/transfer service) to define the hold and transfer feature availability for each extension class of service (cos). Input data class of ser...

  • Page 215: Feature Cross Reference

    Item no. Item input data description default 16 call redirect 0 = off 1 = on turns off or on a multiline terminal user ability to transfer a call to a predefined destination (such as an operator, voice mail, or another extension) without an- swering the call. Cos 01 ~ 15 = 1 17 department group trun...

  • Page 216: Description

    Program 20 : system option setup 20-12 : class of service options (charging cost service) level: in description use program 20-12 : class of service options (charging cost service) to define the charging cost service availability for each extension service class. Input data class of service number 0...

  • Page 217: Description

    Program 20 : system option setup 20-13 : class of service options (supplementary service) level: in description use program 20-13 : class of service options (supplementary service) to define the supplementary feature availability for each extension class of service (cos). Input data class of service...

  • Page 218

    Item no. Item input data description default related program 12 room monitor, extension being monitored 0 = off 1 = on turn off or on an extension ability to be monitored by other extensions. Cos 01 ~ 15 = 0 13 continued dial- ing (dtmf) sig- nal on icm call 0 = off 1 = on turn off or on an extensio...

  • Page 219

    Item no. Item input data description default related program 29 paging display 0 = off 1 = on turns off or on an extension user ability to display paging information. Cos 01 ~ 15 = 1 30 background mu- sic 0 = deny (user cannot control background mu- sic on their station.) 1 = allow (user can control...

  • Page 220: Feature Cross Reference

    Item no. Item input data description default related program 52 voipdb all dsp busy display 0 = disable 1 = enable set whether “all dsp busy” alarm displays on lcd when the caller makes an ip call and there is no voipdb dsp resource. Cos 01 ~ 15 = 1 53 language selec- tion for specific extension 0 =...

  • Page 221: Description

    Program 20 : system option setup 20-14 : class of service options for disa/e&m level: in description use program 20-14 : class of service options for disa/e&m to enable/disable disa and tie line class of service options. You assign a disa class of service to disa users in program 25-09. Assign tie l...

  • Page 222: Feature Cross Reference

    Item no. Item input data description default 10 call forward setting by remote via disa 0 = off 1 = on enable or disable a disa caller ability to use the call forward service codes (pro- grams 11-11-01 ~ 11-11-05). Cos 01 ~ 15 = 0 11 disa/tie trunk barge-in 0 = off 1 = on this option enables or disa...

  • Page 223: 20-15 : Ring Cycle Setup

    Program 20 : system option setup 20-15 : ring cycle setup level: in description use program 20-15 : ring cycle setup to define the ringing cycles for each ring type. Input data item no. Item input data default 01 incoming signal type : normal in- coming call on trunk ringing cycle number : 1 ~ 13 3 ...

  • Page 224: Feature Cross Reference

    Number ringing cycle 11 on : 0.25 / off : 0.25 / on : 0.25 / off : 4.25 12 on : 1.0 / off : 3.0 13 on : 0.25 / off : 0.25 / on : 0.25 / off : 2.25 conditions none feature cross reference none sl1000/sl1100 issue 3.01 2-202 program 20 : system option setup program 20

  • Page 225: Description

    Program 20 : system option setup 20-16 : selectable display messages level: sa description use program 20-16 : selectable display messages to enter the selectable display messages. There are 20 alphanumeric messages, with up to 16 (sl1000) 48 (sl1100) characters. Use the following chart when program...

  • Page 226: Feature Cross Reference

    Number message 5 busy call after ## : ## 6 out for lunch back ## : ## 7 business trip back ## / ## 8 business trip ########## 9 gone for the day 10 on vacation until ## / ## 11 message 11 12 message 12 13 message 13 14 message 14 15 message 15 16 message 16 17 message 17 18 message 18 19 message 19 ...

  • Page 227: 20-17 : Operator Extension

    Program 20 : system option setup 20-17 : operator extension level: in description use program 20-17 : operator extension to designate an operator. When an extension user dials 0 (defined by program 11-01 type 5), calls go to the operator selected in this program. If you do not assign an extension in...

  • Page 228: 20-18 : Service Tone Timers

    Program 20 : system option setup 20-18 : service tone timers level: in description use program 20-18 : service tone timers to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Input data item no. Item inpu...

  • Page 229: Description

    Program 20 : system option setup 20-19 : system options for caller id level: in description use program 20-19 : system options for caller id to define the system options for the caller id feature. Input data item no. Item input data description default 01 caller id displaying format 0 = first 10 dig...

  • Page 230: Description

    Program 20 : system option setup 20-20 : message setup for non-caller id data level: in description use program 20-20 : message setup for non-caller id data to define the messages which are displayed when no caller id information is received. Input data item no. Item input data default 01 private ca...

  • Page 231: Description

    Program 20 : system option setup 20-21 : system options for long conversation level: in description use program 20-21 : system options for long conversation to define the system options for the long conversation feature. Input data item no. Item input data description default related program 01 long...

  • Page 232: Description

    Program 20 : system option setup 20-23 : system options for cti level: in description use program 20-23 : system options for cti to define the system options for the cti feature. Input data item no. Item input data description default 01 delayed ring timer for cti 0 ~ 64800 seconds 30 02 alert repla...

  • Page 233: 20-25 : Isdn Options

    Program 20 : system option setup 20-25 : isdn options level: in description use program 20-25 : isdn options to define the isdn system options. Input data item no. Item input data description default 01 send the release message after sub- scriber hangs up 0 = service off 1 = service on 1 02 progress...

  • Page 234: Feature Cross Reference

    Item no. Item input data description default 14 no response release send 0 = off 1 = on operation mode setting for when second t303 timer expires. 0 conditions none feature cross reference • isdn compatibility sl1000/sl1100 issue 3.01 2-212 program 20 : system option setup program 20

  • Page 235: Description

    Program 20 : system option setup 20-26 : multiplier for charging cost level: in description use program 20-26 : multiplier for charging cost to define the multiplier for charging cost to each extension service class. Input data service class 01 ~ 15 item no. Item input data default 01 value (%) 100 ...

  • Page 236: Description

    Program 20 : system option setup 20-28 : trunk to trunk conversation level: in description use program 20-28 : trunk to trunk conversation to define system options for trunk to trunk conversation. Input data item no. Item input data description default related program 01 conversation continue code 0...

  • Page 237: Description

    Program 20 : system option setup 20-29 : timer class for extension level: in description use program 20-29 : timer class for extension to assign the timer class to each extension. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. Thi...

  • Page 238: Description

    Program 20 : system option setup 20-30 : timer class for trunks level: in description use program 20-30 : timer class for trunks to assign the timer class to each trunk. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. The details o...

  • Page 239: Description

    Program 20 : system option setup 20-31 : timer class timer assignment level: in description use program 20-31 : timer class timer assignment to assign values to the timers on a class of service basis. Input data timer class number 0 ~ 15 item no. Item input data description default related program 0...

  • Page 240

    Item no. Item input data description default related program 10 hold recall time (non exclusive hold) 0 ~ 64800 seconds a call on hold recalls the extension that placed it on hold after this time. This time works with the hold recall callback time (program 24-01-02 ). 90 24-01-01 11 hold recall call...

  • Page 241: Feature Cross Reference

    Item no. Item input data description default related program 22 disa external paging time 0 ~ 64800 seconds this is the maximum length of an external page placed by a disa caller. If the page continues longer than this time, the system termi- nates the disa call. 30 25-07-10 23 page announce- ment d...

  • Page 242: Description

    Program 20 : system option setup 20-34 : remote conference group setup level: sa description use program 20-34 : remote conference group setup to define the remote conference options. Input data remote conference group number 1 ~ 4 item no. Item input data description default 01 conference name up t...

  • Page 243: Description

    Program 20 : system option setup 20-35 : extension's operator setting level: in description use program 20-35 : extension’s operator setting to assign an extension to an operator group. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input data defaul...

  • Page 244: Description

    Program 20 : system option setup 20-36 : trunk's operator setting level: in description use program 20-36 : trunk’s operator setting to assign a trunk to an operator group. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data description default 01 trunk’s oper...

  • Page 245: Description

    Program 20 : system option setup 20-37 : operator extension group setup level: in description use program 20-37 : operator extension group setup to define the operator(s) in the operator group. Input data operator group 1 ~ 15 operator number 1 ~ 8 item no. Item input data default 01 operator extens...

  • Page 246: Description

    Program 20 : system option setup 20-38 : operator group setting level: in description use program 20-38 : operator group setting to set up priority of a call when calling an operator telephone. Input data operator group 1 ~ 15 item no. Item input data description default 01 operator access mode 0 = ...

  • Page 247: Description

    Program 20 : system option setup 20-39 : shortcut operation setup (sl1000) level: in description use program 20-39 : shortcut operation setup to defines the function for shortcut operation. Input data operator group 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , # item no. Item input data default 01 shortcut ope...

  • Page 248: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-226 program 20 : system option setup program 20

  • Page 249: Description

    Program 20 : system option setup 20-40 : function key list setup (sl1000) level: in description use program 20-40 : function key list setup to defines the function list used with function key setting. Input data data no. 1 ~ 10 item no. Item input data default 01 function key list 00 ~ 99, * 00 ~ * ...

  • Page 250: Description

    Program 20 : system option setup 20-41 : service code setup (sl1000) level: in description use program 20-41 : service code setup to set up feature key from dial key. Input data dial 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , # item no. Item input data 01 service code setup 0 = none 1 = call forward - all 2 ...

  • Page 251: Description

    Program 20 : system option setup 20-42 : night mode for each package level: in description use program 20-42 : night mode for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 16 (sl1000) 02 ~ 09 (sl1100) item no. I...

  • Page 252: Description

    Program 20 : system option setup 20-43 : power supply for each package level: in description use program 20-43 : power supply for each package to assigns the night mode to each package. This program uses ecology function (program 20-43). Input data pkg number 02 ~ 16 (sl1000) 02 ~ 09 (sl1100) operat...

  • Page 253: 20-44 : Watch Mode Setup

    Program 20 : system option setup 20-44 : watch mode setup level: in description use program 20-44 : watch mode setup to defines the watch mode. Input data item no. Item input data description default 01 internal paging group for watch message 0 ~ 32 define internal paging group number for watching m...

  • Page 254: 20-45 : Remote Watch Setup

    Program 20 : system option setup 20-45 : remote watch setup level: in description use program 20-45 : remote watch setup to defines the remote watch. Input data terminal number 1 ~ 6 item no. Item input data description default 01 ring terminal for re- mote inspection extension number (up to 4 digit...

  • Page 255: Description

    Program 20 : system option setup 20-46 : security sensor setup level: in description use program 20-46 : security sensor setup to defines the security sensor. Input data security sensor number 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Item input data description default 01 sensor mode 0 = off 1 = on de...

  • Page 256: Description

    Program 20 : system option setup 20-47 : time pattern setting for watch mode level: in description use program 20-47 : time pattern setting for watch mode to defines the watch mode time pattern. Input data time pattern 01 ~ 08 item no. Item input data description default 01 watch mode time pattern 0...

  • Page 257: Description

    Program 20 : system option setup 20-48 : time pattern setting for security sensor level: in description use program 20-48 : time pattern setting for security sensor to defines the security sensor time pattern. Input data time pattern 01 ~ 08 item no. Item input data description default 01 security s...

  • Page 258: Description

    Program 20 : system option setup 20-49 : caller id shared group basic data setup level: in description use program 20-49 : caller id shared group basic data setup to defines the function mode for each caller id shared group. Input data caller id shared group number 01 ~ 08 item no. Item input data d...

  • Page 259: Description

    Program 20 : system option setup 20-55 : delay timer for security sensor level: in (this program is available for v1.5 or higher) description use program 20-55 : delay timer for secuirty sensor to set time for security to be operational. Once it reach the time the security will starts if the securit...

  • Page 260: Description

    Program 21 : outgoing call setup 21-01 : system options for outgoing calls level: in description use program 21-01 : system options for outgoing calls to set the system options for outgoing call service. Input data item no. Item input data description default related program 01 seizure trunk line mo...

  • Page 261

    Item no. Item input data description default related program 10 dial digits for toll restriction path 0 ~ 36 if this option is programmed with an entry other than 0, a call does not have a talk path unless the user di- als at least the number of digits en- tered in this option when placing an outgoi...

  • Page 262: Feature Cross Reference

    Feature cross reference • central office calls, placing sl1000/sl1100 issue 3.01 2-240 program 21 : outgoing call setup program 21.

  • Page 263: Description

    Program 21 : outgoing call setup 21-02 : trunk group routing for extensions level: in description use program 21-02 : trunk group routing for extensions to assign program 14-06 routes to extensions. Input data extension number maximum four digits (sl1000) maximum eight digits (sl1100) day/night mode...

  • Page 264: Description

    Program 21 : outgoing call setup 21-03 : trunk group routing for trunks level: in description use program 21-03 : trunk group routing for trunks to set the trunk route table for automatic external call forward. The route table is set in program 14-06. Input data trunk port number 001 ~ 126 (sl1000) ...

  • Page 265: Description

    Program 21 : outgoing call setup 21-04 : toll restriction class for extensions level: in description use program 21-04 : toll restriction class for extensions to assign a toll restriction class to an extension. The details of toll restriction are defined in program 21-05 and 21-06. A telephone and a...

  • Page 266: Description

    Program 21 : outgoing call setup 21-05 : toll restriction class level: in description use program 21-05 : toll restriction class to set the system toll restriction classes (1 ~ 15). Input data toll restriction class number 1 ~ 15 item no. Item input data description default related program 01 intern...

  • Page 267: Feature Cross Reference

    Item no. Item input data description default related program 09 restriction for common speed dials 0 = does not restrict 1 = following restric- tion check use this option to enable/disable toll restriction for common speed dialing numbers. If enabled, system speed dialing numbers have the same restr...

  • Page 268: Description

    Program 21 : outgoing call setup 21-06 : toll restriction table data setup level: in description use program 21-06 : toll restriction table data setup to set the system toll restriction data. Dial 1 ~ 9, 0, * , # can be entered in each table. Input data item no. Item table input data default 01 inte...

  • Page 269: Feature Cross Reference

    Item no. Item table input data default 07 deny restriction table this option lets you program the restrict code tables. If the system has toll restriction enabled, users cannot dial numbers listed in these ta- bles. There are four restrict code tables, with up to 60 entries in each table. The system...

  • Page 270: Description

    Program 21 : outgoing call setup 21-07 : toll restriction override password setup level: sa description use program 21-07 : toll restriction override password setup to assign toll restriction override codes to extension ports. Each code must have four digits, using any combination of 0 ~ 9, # and * ...

  • Page 271: 21-08 : Repeat Dial Setup

    Program 21 : outgoing call setup 21-08 : repeat dial setup level: in description use program 21-08 : repeat dial setup to define the automatic repeat dial data. Input data item no. Item input data description default 01 repeat redial count 0 ~ 255 sets how many times a repeat redial au- tomatically ...

  • Page 272: 21-09 : Dial Block Setup

    Program 21 : outgoing call setup 21-09 : dial block setup level: in description use program 21-09 : dial block setup to define the dial blocking toll restriction class and dial block password to be used by the supervisor extension. Input data item no. Item input data description default 01 toll rest...

  • Page 273: Description

    Program 21 : outgoing call setup 21-10 : dial block restriction class per extension level: in description use program 21-10 : dial block restriction class per extension to define the toll restriction class to each extension when the extension is set for dial block restriction. If this data is 0, tol...

  • Page 274: Description

    Program 21 : outgoing call setup 21-11 : extension ringdown (hotline) assignment level: in description use program 21-11 : extension ringdown (hotline) assignment to define the hotline destination number for each extension number. Input data extension number maximum four digits (sl1000) maximum eigh...

  • Page 275: Description

    Program 21 : outgoing call setup 21-12 : isdn calling party number setup for trunks level: in description use program 21-12 : isdn calling party number setup for trunks to assign calling party numbers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not ha...

  • Page 276: Description

    Program 21 : outgoing call setup 21-13 : isdn calling party number setup for extensions level: in description use program 21-13 : isdn calling party number setup for extensions to assign each extension a calling party number (maximum 16 digits per entry). The calling number is the subscriber number ...

  • Page 277: Description

    Program 21 : outgoing call setup 21-14 : walking toll restriction password setup level: sa description use program 21-14 : walking toll restriction password setup to assign the password and toll restriction class for walking toll restriction. Each code has six digits, using any combination of 0 ~ 9,...

  • Page 278: Description

    Program 21 : outgoing call setup 21-15 : individual trunk group routing for extensions level: in description use program 21-15 : individual trunk group routing for extensions to designate the alternate trunk access route accessed when a user dials the alternate trunk route access code. Refer to prog...

  • Page 279: Trunk

    Program 21 : outgoing call setup 21-17 : ip trunk (h.323/sip) calling party number setup for trunk level: in description use program 21-17 : ip trunk (h.323/sip) calling party number setup for trunk set the sip calling party number for individual trunks. Input data trunk port number 001 ~ 126 (sl100...

  • Page 280: Extension

    Program 21 : outgoing call setup 21-18 : ip trunk (h.323) calling party number setup for extension level: in description use program 21-18 : ip trunk (h.323) calling party number setup for extension to assign the calling party number for each extension. The assigned number is sent to the exchange wh...

  • Page 281: Extension

    Program 21 : outgoing call setup 21-19 : ip trunk (sip) calling party number setup for extension level: in description use program 21-19 : ip trunk (sip) calling party number setup for extension to set the sip calling party number for an individual extension. Input data extension number up to four d...

  • Page 282: Description

    Program 21 : outgoing call setup 21-20 : sip trunk call discernment setup for extension level: sb description use program 21-20 : sip trunk call discernment setup for extension to set the sip trunk call discernment. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) i...

  • Page 283: Setting)

    Program 21 : outgoing call setup 21-21 : toll restriction for trunks (seized trunk basis setting) level: in description use program 21-21 : toll restriction for trunks (seized trunk basis setting) to define the toll restriction class to each trunk. The details of toll restriction are defined by prog...

  • Page 284: Description

    Program 21 : outgoing call setup 21-22 : co message waiting indication - call back settings level: in description use program 21-22 : co message waiting indication - call back settings to define the settings of co message waiting indication. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 ...

  • Page 285: Description

    Program 21 : outgoing call setup 21-24 : forced access dial data level: in description use program 21-24 : forced access dial data to set for emergency number data. First digit of dialing data should be same as trunk access code. Input data item no. Item input data description default 01 dialing num...

  • Page 286: Description

    Program 22 : incoming call setup 22-01 : system options for incoming calls level: in description use program 22-01 : system options for incoming calls to define the system options for incoming calls. Input data item no. Item input data description default related program 01 incoming call priority 0 ...

  • Page 287: Feature Cross Reference

    Item no. Item input data description default related program 11 vrs waiting message interval time 0 ~ 64800 seconds setup the sending duration time of the auto - attendant & queuing. The message is repeatedly sent out during the specified time. 20 22-14-06 22-15-06 41-11-06 12 mobile extension answe...

  • Page 288: Description

    Program 22 : incoming call setup 22-02 : incoming call trunk setup level: in description use program 22-02 : incoming call trunk setup to assign the incoming trunk type for each trunk. There is one item for each night service mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) d...

  • Page 289: Description

    Program 22 : incoming call setup 22-03 : trunk ring tone range level: in description use program 22-03 : trunk ring tone range to select the ring tone range for the trunk. The trunk uses a ring tone in the range selected when it rings an extension. Eight ring tones are available. Customize the trunk...

  • Page 290: Feature Cross Reference

    Table 2-6 program 22-03 - incoming signal frequency patterns (sl1000) incoming signal frequency pattern tone type pattern 1 600/450/16 hz fm pattern 2 450/16 hz am pattern 3 600 hz pattern 4 1100/1400/16 hz fm pattern 5 660/760/16 hz fm pattern 6 1100/1400/8 hz fm pattern 7 660/760/8 hz fm table 2-7...

  • Page 291: Description

    Program 22 : incoming call setup 22-04 : incoming extension ring group assignment level: sa description use program 22-04 : incoming extension ring group assignment to assign extensions to ring groups. Calls ring extensions according to ring group programming. Use program 22-05 to assign trunks to r...

  • Page 292: Description

    Program 22 : incoming call setup 22-05 : incoming trunk ring group assignment level: in description use program 22-05 : incoming trunk ring group assignment to assign trunks to incoming ring groups. There are 25 available ring groups. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100...

  • Page 293: Description

    Program 22 : incoming call setup 22-06 : normal incoming ring mode level: in description use program 22-06 : normal incoming ring mode to define whether or not an extension should ring for the normal incoming ring mode. Input data extension number maximum four digits (sl1000) maximum eight digits (s...

  • Page 294: 22-07 : Dil Assignment

    Program 22 : incoming call setup 22-07 : dil assignment level: in description use program 22-07 : dil assignment to assign the destination extension or department calling group for each dil incoming trunk. A dil rings an extension directly, without any other access map or ring group programming. If ...

  • Page 295: Description

    Program 22 : incoming call setup 22-08 : dil/irg no answer destination level: in description for dil delayed ringing, use program 22-08 : dil/irg no answer destination to assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time expires (program 22-01-04). ...

  • Page 296: 22-09 : Did Basic Data Setup

    Program 22 : incoming call setup 22-09 : did basic data setup level: in description use program 22-09 : did basic data setup to define the basic setting of dial-in incoming calls for each trunk group. Input data trunk group number 01 ~ 25 item no. Item input data description default 01 expected numb...

  • Page 297: Feature Cross Reference

    Feature cross reference • direct inward dialing (did) issue 3.01 sl1000/sl1100 programming manual 2-275 program 22.

  • Page 298: Description

    Program 22 : incoming call setup 22-10 : did translation table setup level: in description use program 22-10 : did translation table setup to specify the size of the did translation tables. There are 800 (v1.5 or higher) translation table entries that you can allocate among 20 translation tables. In...

  • Page 299: Description

    Program 22 : incoming call setup 22-11 : did translation number conversion level: sa description use program 22-11 : did translation number conversion to specify for each translation table entry (800). • the digits received by the system (eight maximum) • the extension the system dials after transla...

  • Page 300

    Item no. Item input data description default 01 received number maximum eight digits (0 ~ 9, * , #, @) this is the received did digits. Refer below 02 target number maximum 36 digits (0 ~ 9, * , #, @) enter the destination number to which the did number is sent. Refer below 03 did name maximum 8 cha...

  • Page 301: Feature Cross Reference

    Item no. Item input data description default 11 incoming ring group transfer 0 = disable (calls will not be routed to prg 22-12.) 1 = enable (calls will be routed to prg 22-12.) enable (1) or disable (0) each conversa- tion tables ability to follow the ring group programming defined in program 22-12...

  • Page 302: Description

    Program 22 : incoming call setup 22-12 : did intercept ring group level: in description for each did translation table, use program 22-12 : did intercept ring group to define the first destination group for did calls. Depending on the entry in programs 22-09-02 and 22-11-04, the incoming calls route...

  • Page 303: Description

    Program 22 : incoming call setup 22-13 : did trunk group to translation table assignment level: in description use program 22-13 : did trunk group to translation table assignment to assign the did trunk groups to did translation tables. Did trunks should be in their own group. If you have more than ...

  • Page 304: Description

    Program 22 : incoming call setup 22-14 : vrs delayed message for irg level: in description use program 22-14 : vrs delayed message for irg (incoming group ring) to define for each incoming ring group the timers, vrs message number and type of tone for vrs waiting message. Input data incoming ring gr...

  • Page 305: Description

    Program 22 : incoming call setup 22-15 : vrs delayed message for department group level: in description use program 22-15 : vrs delayed message for department group to define for each department (extension) group the timers, vrs message number and tone kind for vrs delayed message. There are 32 avai...

  • Page 306: Description

    Program 22 : incoming call setup 22-16 : private call refuse target area setup level: in description use program 22-16 : private call refuse target area setup to define speed dial group number for private call refuse. Input data item no. Item input data description default 01 speed dial group number...

  • Page 307: Pattern

    Program 22 : incoming call setup 22-17 : dial-in conversion table area setup for time pattern level: sa description use program 22-17: dial-in conversion table area setup for time pattern to define time zone and dial-in conversion table (program 22-11) for time pattern. Input data conversion table n...

  • Page 308: Description

    Program 22 : incoming call setup 22-18 : private call assignment setup level: in description use program 22-18: private call assignment setup to define assignment and incoming ring pattern for private calls. Input data item no. Item input data description default related program 01 transfer mode 0 =...

  • Page 309: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-287 program 22.

  • Page 310: Description

    Program 22 : incoming call setup 22-19 : did mfc dialing options level: in description use program 22-19 : did mfc dialing options to define the mfc dialing for each did table entry. This option is used for latin america only. Input data conversion table number 1 ~ 800 item no. Item input data defau...

  • Page 311: Description

    Program 22 : incoming call setup 22-20 : flexible ringing by caller id setup level: in description use program 22-20: flexible ringing by caller id setup to set flexible ringing by caller id per timer pattern mode. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) day/night mode 01 ...

  • Page 312: 23-02 : Call Pickup Groups

    Program 23 : answer features setup 23-02 : call pickup groups level: in description use program 23-02 : call pickup groups to assign extensions to call pickup groups. This program also lets you assign an extension call pickup group priority. If two extensions in a group are ringing at the same time,...

  • Page 313: Description

    Program 23 : answer features setup 23-03 : universal answer/auto answer level: in description use program 23-03 : universal answer/auto answer to assign trunk routes (set in program 14-06) to extensions for universal answer. If the call ringing the paging system is in an extension assigned route, th...

  • Page 314: Description

    Program 23 : answer features setup 23-04 : ringing line preference for virtual extensions level: in description use program 23-04 : ringing line preference for virtual extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. There are 50 ava...

  • Page 315: Description

    Program 24 : hold/transfer setup 24-01 : system options for hold level: in description use program 24-01 : system options for hold to define the system options for the hold feature. Input data item no. Item input data description default related program 01 hold recall time 0 ~ 64800 seconds a call o...

  • Page 316: Description

    Program 24 : hold/transfer setup 24-02 : system options for transfer level: in description use program 24-02 : system options for transfer to define the system options for the transfer feature. Input data item no. Item input data description default related program 01 busy transfer 0 = disable (no) ...

  • Page 317: Feature Cross Reference

    Item no. Item input data description default related program 09 two b-channel transfer retry timer 0 ~ 30 seconds 10 10-03-16 (pri) 10 disconnect trunk-to-trunk 0 ~ 64800 seconds 0 14-01-25 20-28-01 20-28-02 20-28-03 24-02-07 11 no answer step transfer 0 ~ 64800 seconds 10 14-01-26 12 no answer trun...

  • Page 318: 24-03 : Park Group

    Program 24 : hold/transfer setup 24-03 : park group level: in description use program 24-03 : park group to assign an extension to a park group. The system allows a total of 64 park groups. An extension user can pick up only a call parked in orbit by an extension user in own group. Input data extens...

  • Page 319: Description

    Program 24 : hold/transfer setup 24-04 : automatic trunk-to-trunk transfer target setup level: in description use program 24-04 : automatic trunk-to-trunk transfer target setup to assign the speed dialing number bin which should be used as the destination of the automatic trunk-to-trunk transfer. In...

  • Page 320: Description

    Program 24 : hold/transfer setup 24-05 : department group transfer target setup level: in description use program 24-05 : department group transfer target setup to assign the speed dialing bin which is used as the destination of the extension for the extension group. There are 32 available departmen...

  • Page 321: Description

    Program 24 : hold/transfer setup 24-09 : call forward split settings level: in description use program 24-09 : call forward split settings to assign call forwarding type and the destination number for each extension/virtual extension. The destination can have up to 24 digits, using 0 ~ 9, * , #, and...

  • Page 322: Feature Cross Reference

    Feature cross reference • call forwarding, off-premise sl1000/sl1100 issue 3.01 2-300 program 24 : hold/transfer setup program 24.

  • Page 323: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-01 : vrs/disa line basic data setup level: in description use program 25-01 : vrs/disa line basic data setup to define the basic setting of each vrs/ disa line. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default related ...

  • Page 324: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-02 : did/disa vrs message level: in description use program 25-02 : did/disa vrs message to assign the vrs message number to be used as the automated attendant message for each trunk which is assigned as a vrs/disa. Input data trunk port number 001 ~ 126 (sl1000) 001 ~...

  • Page 325: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-03 : vrs/disa transfer ring group with incorrect dialing level: in description use program 25-03 : vrs/disa transfer ring group with incorrect dialing to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial....

  • Page 326: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-04 : vrs/disa transfer ring group with no answer/ busy level: in description use program 25-04 : vrs/disa transfer ring group with no answer/busy to set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant calle...

  • Page 327: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-05 : vrs/disa error message assignment level: in description use program 25-05 : vrs/disa error message assignment to assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message ...

  • Page 328: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-06 : vrs/disa one-digit code attendant setup level: in description use program 25-06 : vrs/disa one-digit code attendant setup to set up single digit dialing through the vrs. This gives vrs callers single key access to extensions, the company operator, department calli...

  • Page 329: Feature Cross Reference

    Conditions • outside caller may not be able to dial individual extensions or lines if the same first digit is defined here. Feature cross reference • direct inward system access (disa) • voice response system (vrs) issue 3.01 sl1000/sl1100 programming manual 2-307 program 25.

  • Page 330: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-07 : system timers for vrs/disa level: in description use program 25-07 : system timers for vrs/disa to set the value for the system timers which affect did and disa. Refer to the following chart for a description of each option, its range and default setting. Input da...

  • Page 331: Feature Cross Reference

    Item no. Item input data description default related program 09 disa internal paging time 0 ~ 64800 seconds this is the maximum length of an in- ternal page placed by a disa caller. If the page continues longer than this time, the system terminates the disa call. 30 20-31-21 10 disa external paging ...

  • Page 332: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-08 : disa user id setup level: sa description use program 25-08 : disa user id setup to set the 6-digit disa password for each user. There are 15 users each with one 6-digit password. Input data disa user number 01 ~ 15 item no. Item input data default 01 password dial...

  • Page 333: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-09 : class of service for disa users level: in description use program 25-09 : class of service for disa users to set the disa class of service for each user. When a disa caller enters a password (defined in program 25-08), the system identifies the user and associates...

  • Page 334: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-10 : trunk group routing for disa level: in description use program 25-10 : trunk group routing for disa to assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. Enable or disable the dis...

  • Page 335: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-11 : disa toll restriction class level: in description for systems that use toll restriction, use program 25-11 : disa toll restriction class to assign a toll restriction class (1-15) to each disa user (1~15). The system uses the toll restriction class you enter in pro...

  • Page 336: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-12 : alternate trunk group routing for disa level: in description use program 25-12 : alternate trunk group routing for disa to define the trunk route selected when a disa caller dials the alternate trunk access code. The route selected is based on the disa caller clas...

  • Page 337: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-13 : system option for disa level: in description use program 25-13 : system option for disa to enter the password disa callers must dial before the system allows them to record, listen to and or erase the vrs messages. This program also is used to define additional di...

  • Page 338: Program 25 : Vrs/disa Setup

    Program 25 : vrs/disa setup 25-15 : disa transfer target setup level: in description use program 25-15 : disa transfer target setup to assign a speed dial number when a dial tone times-out, or when the wrong number is received and the target extension does not answer or is busy. Input data trunk por...

  • Page 339: Routing

    Program 26 : ars service & least cost routing 26-01 : automatic route selection (ars/f-route) service level: in description use program 26-01 : automatic route selection service (ars/f-route) to define the system options for automatic route selection (ars/f-route). Input data item no. Item input dat...

  • Page 340: Feature Cross Reference

    Feature cross reference • automatic route selection (ars/f-route) sl1000/sl1100 issue 3.01 2-318 program 26 : ars service & least cost routing program 26.

  • Page 341: Routing

    Program 26 : ars service & least cost routing 26-02 : dial analysis table for ars/lcr level: in description use program 26-02 : dial analysis table for ars/lcr to set pre-transaction tables for selecting automatic route selection (ars/f-route). • service type 1 (route to trunk group number) - the nu...

  • Page 342: Feature Cross Reference

    Feature cross reference • automatic route selection (ars/f-route) sl1000/sl1100 issue 3.01 2-320 program 26 : ars service & least cost routing program 26.

  • Page 343: Routing

    Program 26 : ars service & least cost routing 26-03 : ars dial treatments level: in description use program 26-03 : ars dial treatments to assign the 15 dial treatments for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial trea...

  • Page 344: Routing

    Program 26 : ars service & least cost routing 26-04 : ars class of service level: in description use program 26-04 : ars class of service to set the ars class of service for an extension. Automatic route selection (ars/f-route) uses ars class of service when determining how to route extension calls....

  • Page 345: Routing

    Program 26 : ars service & least cost routing 26-05 : lcr carrier table level: in description use program 26-05 : lcr carrier table to define the lcr access codes and routing options. These options include authorization codes and cost center input data item no. Item input data description default 01...

  • Page 346: Routing

    Program 26 : ars service & least cost routing 26-06 : lcr authorization code table level: in description use program 26-06 : lcr authorization code table to define the optional authorization code (or pin code) required by the indirect carrier. The authorization code is inserted if set in program 26-...

  • Page 347: Routing

    Program 26 : ars service & least cost routing 26-07 : lcr cost center code table level: in description use program 26-07 : lcr cost center code table to define the optional cost center code required by the indirect carrier. The cost center code is set for each extension. The cost center code is inse...

  • Page 348: Routing

    Program 26 : ars service & least cost routing 26-08 : lcr manual override access code table level: in description use program 26-08 : lcr manual override access code table to define the access codes that the users can dial to select an indirect carrier i.E. Bypass the automatic selection of program ...

  • Page 349: Routing

    Program 26 : ars service & least cost routing 26-09 : lcr manual override exemption table level: in description use program 26-09 : lcr manual override exemption table to define the numbers that must not be sent via an indirect carrier when the user dials a manual override access code. The exemption...

  • Page 350: Routing

    Program 26 : ars service & least cost routing 26-11 : transit network id table level: in description use program 26-11 : transit network id table to define transit network id for alternate carrier access, which is referred from program 26-03. Input data transit network id table 1 ~ 4 item no. Item i...

  • Page 351: Routing

    Program 26 : ars service & least cost routing 26-12 : network specific parameter table for ars level: in description use program 26-12 : network specific parameter table for ars to define the network specific parameter table. Input data network specific parameter table 1 ~ 16 item no. Item input dat...

  • Page 352: Description

    Program 30 : dss/dls console setup 30-01 : dss console operating mode level: in description use program 30-01 : dss console operating mode to set the mode of the system dss consoles. The entry for this option applies to all the system dss consoles. The available options are: • regular (business) mod...

  • Page 353: Description

    Program 30 : dss/dls console setup 30-02 : dss console extension assignment level: in description use program 30-02 : dss console extension assignment to identify which extensions have dss consoles connected. • up to 12 different extensions with dss consoles can be set up. A single extension can hav...

  • Page 354: Description

    Program 30 : dss/dls console setup 30-03 : dss console key assignment level: sa description use program 30-03 : dss console key assignment to customize the key assignments for 60- button dss consoles. A dss console key can have any function with up to four digits (sl1000) up to eight digits (sl1100)...

  • Page 355

    Function number function additional data led indication note 06 transfer key none 07 conference key on (red) : conference operation 08 incoming call id list fast blink (red) : existing new cid on (red) : existing checked cid off : no cid 09 day/night mode switch mode number (1 ~ 8) on : while each m...

  • Page 356

    Function number function additional data led indication note 39 room monitoring slow blink (red) : monitoring fast blink (red) : to be monitored 41 secretary buzzer extension number (4 digits) (sl1000) extension number (8 digits) (sl1100) on (red) : calling party fast blink : called party 42 boss - ...

  • Page 357

    Function number function additional data led indication note 77 voice mail (in-skin) extension number or pilot number (4 digits) (sl1000) extension number or pilot number (8 digits) (sl1100) fast blink (red) : existing new message 78 conversation recording (in0skin vm) 0 = conversation re- cording 1...

  • Page 358

    Function number function additional data led indication note 93 room status indication none on : checked in and clean off : checked out (clean and available) slow blink : maid required medium blink : maid in room fast blink : inspect room (sl1000) 93 room status indication none on : checked in and c...

  • Page 359: Feature Cross Reference

    Default • the dss keys 001 ~ 060 of all dss consoles = dss/one-touch key 200 ~ 259. • the dss keys 061 ~ 114 of all dss consoles = no setting. (sl1100) conditions none feature cross reference • direct station selection (dss) console issue 3.01 sl1000/sl1100 programming manual 2-337 program 30

  • Page 360: Description

    Program 30 : dss/dls console setup 30-04 : dss console alternate answer (sl1100) level: sa description use program 30-04 : dss console alternate answer to assign the alternate dss console station in case off-duty mode is set (by pressing the alt key on the dss console). Input data index 1 dss consol...

  • Page 361: Description

    Program 30 : dss/dls console setup 30-05 : dss console lamp table level: in description use program 30-05 : dss console lamp table to define the led patterns for functions on the dss consoles. Input data item no. Item input data default 01 idle extension 0 ~ 7 (lamp pattern data) 0 02 busy extension...

  • Page 362

    Pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern #7 1 1 1 1 1 1 0 1 0 1 111 200 400 600 800 10...

  • Page 363: Feature Cross Reference

    Led pattern 0:[o ff] led pattern 1:[fl: o n(500m s)/off(500m s)] o n o ff o n o ff led pattern 2:[w k: o n(250m s)/off(250m s)] o n o ff led pattern 3:[rw : o n(125m s)/off(125m s)] o n o ff led pattern 4:[ir: o n(125m s)/off(125m s)/ o n(125m s)/off(625m s)] led pattern 5:[il o n(875m s)/off(125m s...

  • Page 364: Program 31 : Paging Setup

    Program 31 : paging setup 31-01 : system options for internal/external paging level: in description use program 31-01 : system options for internal/external paging to define the system options for internal/external paging. The system shows the name you program on the telephone display. Use the follo...

  • Page 365: Feature Cross Reference

    Item no. Item input data description default related program 04 privacy release time 0 ~ 64800 seconds once the user initiates a meet-me conference or voice call confer- ence, the system waits this time for the paged party to join the call. 90 seconds conditions none feature cross reference • paging...

  • Page 366: Program 31 : Paging Setup

    Program 31 : paging setup 31-02 : internal paging group assignment level: in description use program 31-02 : internal paging group assignment to assign extensions to internal paging groups (i.E., page zones). The setting in this program also determines if the internal page group can receive internal...

  • Page 367: Program 31 : Paging Setup

    Program 31 : paging setup 31-03 : internal paging group settings level: in description use program 31-03 : internal paging group settings to assign names to internal paging groups (i.E., page zones) and to define the splash tone for internal paging. The system shows the names you program on the tele...

  • Page 368: Feature Cross Reference

    Item no. Item input data description default 02 internal paging splash tone type 0 = ordinary volume 1 = mute 2 = no tone allow an extension to have normal (0), muted (1) or no (2) internal paging alert beeps before a paging announcement. 0 default item 01 : internal paging group name extension pagi...

  • Page 369: Program 31 : Paging Setup

    Program 31 : paging setup 31-04 : external paging zone group level: in description use program 31-04 : external paging zone group to assign each external paging zone to an external paging group. Users call the external paging group when broadcasting announcements to the external zone. To simplify pr...

  • Page 370: Program 31 : Paging Setup

    Program 31 : paging setup 31-05 : universal night answer/ring over page level: in description use program 31-05 : universal night answer/ring over page to assign universal night answer ringing to each external paging zone. For each trunk port, make a separate entry for each external paging zone. For...

  • Page 371: Program 31 : Paging Setup

    Program 31 : paging setup 31-06 : external speaker control level: in description use program 31-06 : external speaker control to define the settings for the external speaker using an amplifier. Input data external speaker number 1 ~ 3 item no. Item input data description default 01 broadcast splash ...

  • Page 372: Program 31 : Paging Setup

    Program 31 : paging setup 31-07 : combined paging assignments level: in description use program 31-07 : combined paging assignments to assign an external paging group (0 ~ 3) to an internal paging zone (0 ~ 32) for combined paging. When an extension user makes a combined page, they simultaneously br...

  • Page 373: Program 31 : Paging Setup

    Program 31 : paging setup 31-08 : bgm on external paging level: in description use program 31-08 : bgm on external paging to set the background music option for each external paging zone. If enabled, the system plays background music over the zone when it is idle. Input data external speaker number ...

  • Page 374: Program 31 : Paging Setup

    Program 31 : paging setup 31-10 : external paging group basic setting level: in description use program 31-10 : external paging group basic setting assigns the name of external paging group and defines the splash tone for external paging. Input data external speaker number 01 ~ 03 item no. Item inpu...

  • Page 375: Description

    Program 32 : door box and sensor setup 32-01 : door box timers setup level: in description use program 32-01 : door box timers setup to assign the timers used for the door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data item no. I...

  • Page 376: Description

    Program 32 : door box and sensor setup 32-02 : door box ring assignment level: sa description use program 32-02 : door box ring assignment to assign the extension which rings when a caller presses the associated door box call button. The door box feature is called door phone when programming via web...

  • Page 377: 32-03 : Door Box Basic Setup

    Program 32 : door box and sensor setup 32-03 : door box basic setup level: in description use program 32-03 : door box basic setup to select the chime pattern and gain level for each door box. There are six distinctive chime patterns. The chime tones are defined in 80-01 : service tone setup. On pag...

  • Page 378: 32-04 : Door Box Name Setup

    Program 32 : door box and sensor setup 32-04 : door box name setup level: in description use program 32-04 : door box name setup to define the name of each door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Input data door box number 1 ~ 8...

  • Page 379: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-01 : e&m tie line basic setup level: in description use program 34-01 : e&m tie line basic setup to define the basic settings for each e&m tie line. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data description default related ...

  • Page 380: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-02 : e&m tie line class of service level: in description use program 34-02 : e&m tie line class of service to assign a class of service to a tie line (there are 15 tie line classes of service). The class of service options are defined in program 20-14. For each tie lin...

  • Page 381: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-03 : trunk group routing for e&m tie lines level: in description use program 34-03 : trunk group routing for e&m tie lines to assign the trunk group route 01 ~ 25) chosen when a user seizes a tie line and dials 9. (set trunk group routing in program 14-07.) if the syst...

  • Page 382: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-04 : e&m tie line toll restriction class level: in description use program 34-04 : e&m tie line toll restriction class to enter a toll restriction class for each tie line. There are 15 toll restriction classes which are defined in programs 21-05 and 21-06. For each tie...

  • Page 383: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-05 : tie line outgoing call restriction level: in description use program 34-05 : tie line outgoing call restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.G., dialed from a tie line). For each inbound trunk group, enable...

  • Page 384: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-06 : add/delete digit for e&m tie line level: in description use program 34-06 : add/delete digit for e&m tie line to set digits that the system should add or delete for tie lines. • delete digit some tie line networks pass the location number and extension number to t...

  • Page 385: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-07 : e&m tie line timer level: in description use program 34-07 : e&m tie line timer to define the system service tone timers. Input data item no. Item input data default 01 first digit pause (e&m immediate start) 0 ~ 64800 seconds 3 02 first digit pause (e&m wink star...

  • Page 386: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-08 : toll restriction data for e&m tie lines level: in description use program 34-08 : toll restriction data for e&m tie lines to define the toll restriction data for e&m tie lines. This data should be defined if tie line toll restriction is enabled in program 21-05-13...

  • Page 387: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-09 : ani/dnis service options level: in description use program 34-09 : ani/dnis service options to define the ani/dnis service option setup for e&m class of service. Input data class of service 01 ~ 15 item no. Item input data description default related program 01 re...

  • Page 388

    Item no. Item input data description default related program 04 route table set- up of target dial 0 = spd table (program 13-03) 1 = did table (program 22-11) the option sets how the system uses the route data (gathered in item 3) to route incoming ani/dnis calls. If option 2 is selected, and the ca...

  • Page 389: Feature Cross Reference

    Item no. Item input data description default related program 09 calling number address length 1 ~ 8 when item 01 = 0 (ani/dnis re- ceive format is the address), use this option to specify the address length. The choices are from 1 ~ 8 digits. Cos 01 = 7 cos 02 ~ 15 = 7 34-09-01 conditions none featu...

  • Page 390: Program 34 : Tie Line Setup

    Program 34 : tie line setup 34-11 : e1 trunk basic setup level: in description use program 34-11 : e1 trunk basic setup to define the basic setting of each e1 trunk. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data description default 01 e1 trunk type 0 = s...

  • Page 391: Feature Cross Reference

    Conditions • after set program 34-11-01, system needs to be re-started. Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-369 program 34.

  • Page 392: 35-01 : Smdr Options

    Program 35 : smdr account code setup 35-01 : smdr options level: in description use program 35-01 : smdr options to set the smdr (station message detail recording) options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range and default setting. ...

  • Page 393: Feature Cross Reference

    Feature cross reference • station message detail recording issue 3.01 sl1000/sl1100 programming manual 2-371 program 35.

  • Page 394: 35-02 : Smdr Output Options

    Program 35 : smdr account code setup 35-02 : smdr output options level: in description use program 35-02 : smdr output options to set the smdr (station message detail recording) output options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range ...

  • Page 395: Feature Cross Reference

    Item no. Item input data description default 13 cli output when did to trunk 0 = not displayed 1 = displayed determine if the cli output should be dis- played for did. 0 14 date 0 = not displayed 1 = displayed determine whether or not the date should be displayed on smdr reports. This option must be...

  • Page 396: Description

    Program 35 : smdr account code setup 35-03 : smdr port assignment for trunk group level: in description use program 35-03 : smdr port assignment for trunk group to assign the smdr port for each trunk group. For each trunk group, select the smdr port where the incoming smdr information should be sent...

  • Page 397: Description

    Program 35 : smdr account code setup 35-04 : smdr port assignment for department groups level: in description use program 35-04 : smdr port assignment for department groups to assign the smdr port for each department group. For each department group, select the smdr port where the outgoing smdr info...

  • Page 398: 35-05 : Account Code Setup

    Program 35 : smdr account code setup 35-05 : account code setup level: in description use program 35-05 : account code setup to set various account code options for an extension class of service. Assign a class of service to extensions in program 20-06. Input data class of service number 01 ~ 15 ite...

  • Page 399: Feature Cross Reference

    Feature cross reference • account code forced/verified/unverified issue 3.01 sl1000/sl1100 programming manual 2-377 program 35.

  • Page 400: Description

    Program 35 : smdr account code setup 35-06 : verified account code table level: in description use program 35-06 : verified account code table to enter account codes into the verified account code list. You can enter up to 800 codes with 1 ~ 16 digits, using the characters 0 ~ 9 or #. Use the lk1 to...

  • Page 401: Description

    Program 40 : voice recording system 40-07 : voice prompt language assignment for vrs level: in description use program 40-07 : voice prompt language assignment for vrs to specify the language to be used for the vrs prompts. Input data item no. Item input data default 01 voice prompt language assign-...

  • Page 402: Description

    Program 40 : voice recording system 40-10 : voice announcement service option level: in description in program 40-10 : voice announcement service option define the system options for the voice announcement feature. Input data item no. Item input data description default related program 01 vrs fixed ...

  • Page 403: Feature Cross Reference

    Item no. Item input data description default related program 09 call attendant no answer mes- sage 0 ~ 100 (0 = no message) 0 15-01-09 10 call forward re- mainder an- nouncement (v2.0 added) 0 = do not play 1 = play flag that control the playback of the vrs announcements for 'on the for- warded phon...

  • Page 404: Description

    Program 40 : voice recording system 40-11 : preamble message assignment level: in description in program 40-11 : preamble message assignment to assign the vrs message number to be used as the preamble message for each trunk. When the extension user answers the incoming call, the assigned vrs message...

  • Page 405: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-01 : system options for hotel/motel level: in description use program 42-01 : system options for hotel/motel to assign the system options for hotel/motel service. Input data item no. Item input data description default 01 answering message mode for wake up call (hotel mod...

  • Page 406: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-02 : hotel/motel telephone setup level: in description use program 42-02 : hotel/motel telephone setup to define the basic operation of the hotel/motel extensions. Input data extension number up to four digits (sl1000) up to eight digits (sl1100) item no. Item input data ...

  • Page 407: Feature Cross Reference

    Feature cross reference • hotel/motel issue 3.01 sl1000/sl1100 programming manual 2-385 program 42.

  • Page 408: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-03 : class of service options (hotel/motel) level: in description use program 42-03 : class of service options (hotel/motel) to set the hotel/motel class of service (cos) options. Assign class of service to extensions in program 42-02 : hotel/motel telephone setup. There ...

  • Page 409: Feature Cross Reference

    Item no. Item input data description default 16 show guest name on this staff phone (v3.0 added) 0 = disable 1 = enable enable guest name indication on staff ter- minal. (setting for staff terminal) 1 conditions none feature cross reference • class of service • hotel/motel issue 3.01 sl1000/sl1100 p...

  • Page 410: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-04 : hotel mode one-digit service codes level: in description use program 42-04 : hotel mode one-digit service codes to set up the hotel mode one-digit service codes which are assigned in 42-02-01. For each department calling group (01 ~ 32), you enter the destination for...

  • Page 411: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-05 : hotel room status printer level: in description use program 42-05 : hotel room status printer to set the lan port to output the hotel data (check-out sheet, room status, etc.) and the output options for the hotel/ motel feature. Input data item no. Item input data de...

  • Page 412: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-06 : pms service setting level: in (this program is available for v2.0 or higher) description use prg 42-06 : pms service setting to set the pms integration settings when using pms-u13 and pms feature. Input data item no. Item input data description default 01 pms port nu...

  • Page 413: Feature Cross Reference

    Conditions none feature cross reference • hotel/motel issue 3.01 sl1000/sl1100 programming manual 2-391 program 42.

  • Page 414: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-07 : pms restriction level conversion table level: in (this program is available for v2.0 or higher) description use prg 42-07 : pms restriction level conversion table to change the default toll restriction class on check in for a room (prg 42-02-02). This command transla...

  • Page 415: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-08 : text message setup for hotel room status level: in description use program 42-08 : text message setup for hotel room status to define the text message for hotel room status. Input data room status number 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , # room status 0 = check in 1 ...

  • Page 416: Feature Cross Reference

    No. Room status fidelio code alphanumeric 12345678901234567890123456789012 9 check in 4 check out 3 0 check in 6 check out 5 * check in 4 check out 3 # check in 4 check out 3 conditions none feature cross reference • hotel/motel sl1000/sl1100 issue 3.01 2-394 program 42 : hotel setup program 42.

  • Page 417: Program 42 : Hotel Setup

    Program 42 : hotel setup 42-09 : flexible setup for room status level: in (this program is available for v2.0 or higher) description use program 42-09 : flexible setup for room status to enable dial room status codes. Note the code definitions only apply to the system itself. Input data room status ...

  • Page 418: Description

    Program 44 : ars/f-route setup 44-01 : system options for ars/f-route level: in description use program 44-01 : system options for ars/f-route to define the system options for the ars/f- route feature. Input data item no. Item input data description default 01 ars/f-route time schedule 0 = not used ...

  • Page 419: Description

    Program 44 : ars/f-route setup 44-02 : dial analysis table for ars/f-route access level: in description use program 44-02 : dial analysis table for ars/f-route access to set the pre-transaction table for selecting ars/f-route. Input data dial analysis table number 001 ~ 120 item no. Item input data ...

  • Page 420: Feature Cross Reference

    Item no. Item input data description default 03 additional data 1 = delete digit = 0 ~ 255 (255 = delete all digits) 2 = 0 ~ 100 (0 = no set- ting) 3 = dial extension ana- lyze table number = 0 ~ 4 (0 = no setting) for the service type selected in 44-02-02, enter the additional data required. • 1 : ...

  • Page 421: Description

    Program 44 : ars/f-route setup 44-03 : dial analysis extension table level: in description when program 44-02-02 is set to type 3, use program 44-03 : dial analysis extension table to set the dial extension analysis table. These tables are used when the analyzed digits must be more than eight digits...

  • Page 422: Feature Cross Reference

    Conditions none feature cross reference • automatic route selection (ars/f-route) sl1000/sl1100 issue 3.01 2-400 program 44 : ars/f-route setup program 44.

  • Page 423: Description

    Program 44 : ars/f-route setup 44-04 : ars/f-route selection for time schedule level: in description use program 44-04 : ars/f-route selection for time schedule to assign each ars/ f-route selection number to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for ...

  • Page 424: 44-05 : Ars/f-Route Table

    Program 44 : ars/f-route setup 44-05 : ars/f-route table level: in description use program 44-05 : ars/f-route table to set the ars/f-route table. There are four kinds of order. If the higher priority trunk groups are busy, the next order group is used. If a lower priority route is selected, the cal...

  • Page 425: Feature Cross Reference

    Feature cross reference • automatic route selection (ars/f-route) issue 3.01 sl1000/sl1100 programming manual 2-403 program 44.

  • Page 426: Description

    Program 44 : ars/f-route setup 44-06 : additional dial table level: in description use program 44-06 : additional dial table to set the additional dial table to add prior to the dialed ars/f-route number. The additional dial table used is determined in program 44-05-03. Input data additional dial ta...

  • Page 427: Description

    Program 44 : ars/f-route setup 44-07 : gain table for ars/f-route access level: in description use program 44-07 : gain table for ars/f-route access to set the gain/pad table. If an extension dials ars/f-route number: • the extension dial gain table, assigned in program 44-05, is activated. • the ex...

  • Page 428: Description

    Program 44 : ars/f-route setup 44-08 : time schedule for ars/f-route level: in description use program 44-08 : time schedule for ars/f-route to define the daily pattern of the ars/f- route feature. Ars/f-route has 10 time patterns. These patterns are used in programs 44-09 and 44-10. The daily patte...

  • Page 429: Feature Cross Reference

    Feature cross reference • automatic route selection (ars/f-route) issue 3.01 sl1000/sl1100 programming manual 2-407 program 44.

  • Page 430: Description

    Program 44 : ars/f-route setup 44-09 : weekly schedule for ars/f-route level: in description use program 44-09 : weekly schedule for ars/f-route to define a weekly schedule for using ars/f-route. The pattern number is defined in program 44-08-01. Input data day number 1 = sunday 2 = monday 3 = tuesd...

  • Page 431: Description

    Program 44 : ars/f-route setup 44-10 : holiday schedule for ars/f-route level: in description use program 44-10 : holiday schedule for ars/f-route to define a yearly schedule for ars/f- route. This schedule is used for setting special days such as national holidays. The pattern number is defined in ...

  • Page 432: Description

    Program 45 : voice mail integration 45-01 : voice mail integration options level: in description use program 45-01 : voice mail integration options to customize certain voice mail integration options. Input data item no. Item input data description default related program 01 voice mail de- partment ...

  • Page 433: Feature Cross Reference

    Item no. Item input data description default related program 15 analog voice mail protocol se- lection 0 = fixed 1 = program assigns whether fixed codes are used or the codes used in program 45-04 are used for analog voice mail protocol. 0 45-04 11-11-50/5 1 16 voice mail fax digit add as- signment ...

  • Page 434: 45-02 : Nsl Option Setup

    Program 45 : voice mail integration 45-02 : nsl option setup level: sa description use program 45-02 : nsl option setup to setup the nsl options for voice mail integration. Input data item no. Item input data default 01 send dtmf tone or 6kd message 0 = send dtmf tone to slt-vm port 1 = send 6kd mes...

  • Page 435: Description

    Program 45 : voice mail integration 45-04 : voice mail digit add assignment level: in description use program 45-04 : voice mail digit add assignment to define the digits to add. Input data item no. Item input data default related program 01 remote logon (internal) up to four digits no setting 45-01...

  • Page 436: Digits

    Program 45 : voice mail integration 45-05 : voice mail send protocol signal without additional digits level: in description use program 45-05 : voice mail send protocol signal without additional digits to send trunk number and/or station number information if integrating to voice mail when program 4...

  • Page 437: Program 47 : Inmail

    Program 47 : inmail 47-01 : inmail system options level: in description use program 47-01 : inmail system options to set up the inmail system-wide options. Input data item no. Item input data description default 02 inmail master name up to 12 characters (mastername) the cpu must be reset for a chang...

  • Page 438

    Item no. Item input data description default 05 message backup/go ahead time 1 ~ 6015 seconds (msg bkup/adv time) use this option to set the backup/ go ahead time. This time sets how far inmail backs up when a user dials b while listen- ing to a message. This interval also sets how far inmail jumps ...

  • Page 439

    Item no. Item input data description default 10 wait between non- pager callout at- tempts 1 ~ 255 minutes (notify n-pgr intvl) use this option to set the minimum time (1 ~ 255 minutes) between non-pager mes- sage notification callouts in which the des- tination answers, says hello, dials 1 to ac- k...

  • Page 440: Feature Cross Reference

    Item no. Item input data description default 17 inmail port 0 ~ 113 (sl1000) 0 ~ 105 (sl1100) the first port of inmail must start with one of the following ports: 5, 9, 13, 17, 21, 25, 29, 33, 37, 41, 45, 49, 53, 57, 61, 65, 69, 73, 77, 79, 81, 85, 89, 93, 97, 101, 105 0 18 play pad control 1 ~ 63 (...

  • Page 441: Program 47 : Inmail

    Program 47 : inmail 47-02 : inmail station mailbox options level: in description use program 47-02 : inmail station mailbox options to set up a station/extension mailbox. Station mailboxes are automatically assigned as subscriber mailboxes. Normally, inmail station mailbox numbers 1 ~ 64 should corr...

  • Page 442

    Item no. Item input data description default 05 auto erase/save of messages 0 = erase after the subscriber lis- tens to the entire new message and hangs up, inmail erases the mes- sage. 1 = save after the subscriber lis- tens to the entire new message and hangs up, inmail saves the mes- sage. Use th...

  • Page 443

    Item no. Item input data description default 10 forced unscreened transfer 0 = no (disabled) 1 = yes (enabled) (forced utrf) use this option to enable or disable auto- mated attendant forced unscreened transfer for the subscriber mailbox. If ena- bled, each screened transfer (trf) to the extension i...

  • Page 444: Feature Cross Reference

    Item no. Item input data description default 24 all find-me follow- me enabled 0 = no 1 = yes 0 25 security code option 0 = always 1 = remote logon only 0 26 auto play (v1.5 add- ed) 0 = disabled 1 = enable 0 27 email message save/ delete option (v1.5 added) 0 = no change 1 = save 2 = delete 0 28 qu...

  • Page 445: Program 47 : Inmail

    Program 47 : inmail 47-03 : inmail group mailbox options level: in description use program 47-03 : inmail group mailbox options to set up the 32 group mailboxes (01 ~ 32). A group mailbox is used for department group overflow and can be a subscriber or call routing. Input data group mailbox number 0...

  • Page 446: Program 47 : Inmail

    Program 47 : inmail 47-06 : group mailbox subscriber options level: in description use program 47-06 : group mailbox subscriber options to set up a master mailbox assigned as a subscriber mailbox in 47-03-03 : master mailbox type. Input data group mailbox number 01 ~ 32 item no. Item input data desc...

  • Page 447

    Item no. Item input data description default 05 recording conversa- tion beep 0 = no (disabled) 1 = yes (enabled) (rec conv beep) use this option to enable or disable the conversation record beep. If enabled, all parties on a call hear the voice prompt “recording”, followed by a single beep when the...

  • Page 448

    Item no. Item input data description default 11 dialing option 0 = no (disabled) 1 = yes (enabled) dialing option provides additional dialing options for next call routing mailbox calls (see next call routing mailbox below). If enabled, a caller who accesses the sub- scriber mailbox to leave a messa...

  • Page 449: Feature Cross Reference

    Table 2-11 47-06-14 default table item name input data 47-06-14 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 450: Program 47 : Inmail

    Program 47 : inmail 47-07 : inmail routing mailbox options level: in description use program 47-07 : inmail routing mailbox options to set up the 32 routing mailboxes. Routing mailboxes can be either announcement or call routing mailboxes. Input data routing mailbox number 01 ~ 32 item no. Item inpu...

  • Page 451: Feature Cross Reference

    Table 2-12 47-07-03 default table item name input data 47-07-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 452: Program 47 : Inmail

    Program 47 : inmail 47-08 : call routing mailbox options level: in description use program 47-08 : call routing mailbox options to set the options for mailboxes assigned as call routing mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data d...

  • Page 453: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-431 program 47.

  • Page 454: Program 47 : Inmail

    Program 47 : inmail 47-09 : announcement mailbox options level: in description use program 47-09 : announcement mailbox options to set the options for mailboxes assigned as announcement mailboxes in 47-07-02 : routing mailbox type. Input data routing mailbox number 01 ~ 32 item no. Item input data d...

  • Page 455: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-433 program 47.

  • Page 456: Program 47 : Inmail

    Program 47 : inmail 47-10 : inmail trunk options level: in description use program 47-10 : inmail trunk options to assign inmail options for each trunk. Currently, only 47-10-01 : answer table assignment is available. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item i...

  • Page 457: Feature Cross Reference

    Table 2-13 47-10-03 default table item name input data 47-10-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin america spanish 08 = italian 09 = german 10 = madrid spanish 11 = norwegian 12 = parisian fren...

  • Page 458: Program 47 : Inmail

    Program 47 : inmail 47-11 : inmail answer table options level: in description use program 47-11 : inmail answer table options to set options for the answer tables. Inmail provides eight answer tables (1 ~ 16 (v3.0 higher) ). To set up the schedules for each answer table, go to 47-12 : inmail answer ...

  • Page 459

    Item no. Item input data description default 02 override mailbox category (over- ride mb ctg) use this option to specify the category of the mailbox where automated at- tendant calls should route when you enable answer schedule override. • if the override mailbox is a sub- scriber mailbox, the outsi...

  • Page 460: Feature Cross Reference

    Item no. Item input data description default 03 default mailbox category(default mb ctg) use this option to specify the category of mailbox used as the default mail- box. • if the default mailbox is a sub- scriber mailbox, the outside caller hears the mailbox greeting (if recor- ded) and can leave a...

  • Page 461: Program 47 : Inmail

    Program 47 : inmail 47-12 : inmail answer schedules level: in description use program 47-12 : inmail answer schedules to set up the inmail automated attendant answer schedules. There are eight answer tables, with up to 10 answer schedules in each answer table. Input data answer table number 1 ~ 16 (...

  • Page 462

    Item no. Item input data default description 01 schedule type 0 = undefined 1 = day of the week 2 = range of days 3 = date answer table 1/ schedule 1 = 2 all other schedules = 0 (entryxx schedule type) use this option to assign a sched- ule type to the selected answer schedule. The schedule type de-...

  • Page 463

    Item no. Item input data default description 02 answering mailbox catego- ry (entryxx mb ctg) use this option to specify the category of mailbox to which automated attendant calls should route when the sched- ule is in effect. If the answering mailbox is a subscriber mailbox, the out- side caller he...

  • Page 464: Feature Cross Reference

    Item no. Item input data default description 06 date (entryxx date) for date (type 3) answer schedules, use this option to select the date the answer schedule should be active. Mmdd for example : - 0101 = january 1 - 1231 = december 31 (0000 = undefined) all schedule = 0000 07 schedule start time (e...

  • Page 465: Program 47 : Inmail

    Program 47 : inmail 47-13 : inmail dial action tables level: in description use program 47-13 : inmail dial action tables to set up the inmail dial action tables. The dial action table defines the options than an automated attendant caller can dial. A dial action table is associated with a call rout...

  • Page 466

    Item no. Name input data description 01 action 0 = und (undefined) 1 = trf (transfer) 2 = utrf (unscreened transfer) 3 = rec1 4 = rec2 5 = logon 6 = hang up 7 = goto • trf action - screened transfer (1) (trf) • utrf action - unscreened transfer (2) (utrf) • rec1 action - quick message with greeting ...

  • Page 467: Feature Cross Reference

    Dial action table default settings key dial action table 1 dial action table 2 ~ 16 action data action data 8 0 (und) 0 0 (und) 0 9 6 (hang up) 0 0 (und) 0 0 2 (utrf) 200 0 (und) 0 * 3 (rec1) ixxx 0 (und) 0 # 5 (logon) ixxx 0 (und) 0 timeout 2 (utrf) 200 0 (und) 0 timeout provides the routing for ro...

  • Page 468: Program 47 : Inmail

    Program 47 : inmail 47-15 : routing directory mailbox options level: in description use program 47-15 : routing directory mailbox options to define the routing directory mailbox options. This data is referred if program 47-07-02 (routing master mailbox type) was set to type 4 (directory). Input data...

  • Page 469: Program 47 : Inmail

    Program 47 : inmail 47-17 : routing distribution mailbox options level: in description use program 47-17 : routing distribution mailbox options to assign data when program 47-07-02 is set to 4 (distribution). Input data routing mailbox number 01 ~ 32 entry number 01 ~ 20 item no. Item input data des...

  • Page 470: Program 47 : Inmail

    Program 47 : inmail 47-18 : inmail smtp setup level: in description use program 47-18 inmail smtp setup to set the snmp e-mail notification. Input data item no. Item input data default 01 smtp enabled 0 = no 1 = yes 0 02 server name up to 48 characters no setting 03 smtp port 0 ~ 65535 25 04 encrypt...

  • Page 471: Program 47 : Inmail

    Program 47 : inmail 47-19 : inmail pop3 setup level: in description use program 47-19 : inmail pop3 setup to set the inmail e-mail notification. Input data item no. Item input data default 01 server name up to 48 characters no setting 02 pop3 port 0 ~ 65535 110 03 encryption 0 = no 1 = yes 0 04 user...

  • Page 472: Program 47 : Inmail

    Program 47 : inmail 47-20 : station mailbox message notification options level: in description use program 47-20 : station mailbox message notification options to define the intramail station mailbox message notification options. Input data station mailbox number 001 ~ 128 (sl1000) 001 ~ 120 (sl1100...

  • Page 473: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-451 program 47.

  • Page 474: Program 47 : Inmail

    Program 47 : inmail 47-21 : station mailbox find-me follow-me options level: in description use program 47-21 : station mailbox find-me follow-me options to define the intramail station mailbox find-me follow-me options. Input data station mailbox number 001 ~ 128 (sl1000) 001 ~ 120 (sl1100) index n...

  • Page 475: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-453 program 47.

  • Page 476: Program 47 : Inmail

    Program 47 : inmail 47-22 : group mailbox message notification options level: in description use program 47-22 : group mailbox message notification options to define the intramail group mailbox message notification options. Input data group mailbox number 01 ~ 32 index number 1 ~ 5 item no. Item inp...

  • Page 477: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-455 program 47.

  • Page 478: Program 47 : Inmail

    Program 47 : inmail 47-23 : group mailbox find-me follow-me options level: in description use program 47-23 : group mailbox find-me follow-me options to define the intramail group mailbox find-me follow-me options. Input data group mailbox number 01 ~ 32 index number 1 ~ 3 item no. Item input data d...

  • Page 479: 80-01 : Service Tone Setup

    Program 80 : basic hardware setup for system 80-01 : service tone setup level: in description use program 80-01 : service tone setup to define up to 64 service tones. Each service tone is defined by the combination of 32 basic tones. Input data service tone number 01 ~ 64 item no. Item input data de...

  • Page 480

    Basic tone no. Frequency (hz) level (db) 15 650 / 780 -19 / -13 16 780 / 1040 -19 / -13 17 520 / 650 -13 / -19 18 650 / 780 -13 / -19 19 780 / 1040 -13 / -19 20 1040 -13 21 450 -13 22 950 -13 23 1800 -13 24 400 / 450 -13/-13 25 400 - 13 26 350 / 440 - 13/- 13 27 420 (amplitude modulated) - 13 28 -- ...

  • Page 481

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 13 external hold tone 0 0 0 0 32 (0 db) 14 internal ring-back tone (internal audible ring) (ring back tone) 0 2 1 0 10 40 42 (+ 5 db) 42 (+ 5 db) 15 override tone 1 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) ...

  • Page 482

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 28 speaker monitor tone 1 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) 29 door relay tone 1 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) 30 doorphone call tone 1 2 0 1 1 1 42 (+ 5 db) 42 (+ 5 db) 31 paging tone 2 2 0 1 1 ...

  • Page 483: Feature Cross Reference

    Serv- ice tone no. Service tone name repeat count unit count basic tone no. Duration gain level (db) 53 external executive override tone 1 2 1 0 10 10 42 (+ 5 db) 42 (+ 5 db) 55 generate tone for tapi2.1 0 1 22 10 32 (0 db) 56 warning beep tone signal- ing 1 1 22 0 8 8 32 (0 db) 32 (0 db) 57 headset...

  • Page 484: 80-02 : Dtmf Tone Setup

    Program 80 : basic hardware setup for system 80-02 : dtmf tone setup level: mf description use program 80-02 : dtmf tone setup to define the duration (on time) and pause (off time) for dtmf dialing. This option affects all trunk line calls system wide. Make separate entries for duration and pause. I...

  • Page 485: Description

    Program 80 : basic hardware setup for system 80-03 : dtmf tone receiver setup level: in description use program 80-03 : dtmf tone receiver setup to define the various levels and timers for the dtmf tone receiver. Dtmf tone receiver type : • 1 = dtmf receiver for extension • 2 = dtmf receiver for tru...

  • Page 486: Feature Cross Reference

    Item no. Item input data description default 04 max. Detect level 0 ~ 15 dtmf tone 0 = 0 dbm (0) to - 15 dbm (15) dtmf tone 1 = - 5 dbm (0) to - 20 dbm (15) dtmf tone 2 = - 10 dbm (0) to - 25 dbm (15) dtmf tone 3 = - 15 dbm (0) to - 30 dbm (15) dtmf tone 4 = - 20 dbm (0) to - 35 dbm (15) dtmf tone 5...

  • Page 487: Description

    Program 80 : basic hardware setup for system 80-04 : call progress tone detector setup level: in description use program 80-04 : call progress tone detector setup to define the various levels and timers for the call progress tone detector. Tone detector type : • 1 = dial tone for trunk • 2 = busy to...

  • Page 488: Feature Cross Reference

    Item no. Item input data default 08 off minimum time 1 ~ 255 (30 + 30 ~ 7680 ms) refer below 09 off maximum time 0 ~ 255 (30 + 30 ~ 7680 ms) refer below 12 frequency no. 1 1 ~ 8 (frequency table no. Set by 80-07) refer below 13 frequency no. 2 0 ~ 8 (0 = not used) (frequency table no. Set by 80-07) ...

  • Page 489: Description

    Program 80 : basic hardware setup for system 80-05 : date format for smdr and system level: in description use program 80-05 : date format for smdr and system to define the date format when printing out the smdr, alarm report, and system information report. Input data item no. Item input data defaul...

  • Page 490: Description

    Program 80 : basic hardware setup for system 80-06 : reference impedance setup level: in description use program 80-06: reference impedance setup to define the change of reference impedance (600 Ω or complex) in coiu pkg (sl1000) use program 80-06: reference impedance setup to define the change of r...

  • Page 491: Description

    Program 80 : basic hardware setup for system 80-07 : call progress tone detector frequency setup level: in description use program 80-07 : call progress tone detector frequency setup to set the frequency of the detection tone set with program 80-04-12 and program 80-04-13. Input data frequency table...

  • Page 492: 80-08 : Mfc Tone Setup

    Program 80 : basic hardware setup for system 80-08 : mfc tone setup level: in description use program 80-08 : mfc tone setup to define the duration (on time) and pause (off time) for mfc dialing. This option affects all trunk line calls system wide. And also it is possible to adjust the level of ton...

  • Page 493: 80-09 : Short Ring Setup

    Program 80 : basic hardware setup for system 80-09 : short ring setup level: in description use program 80-09 : short ring setup to define the short ring tone for sl1000/sl1100 multiline terminals. Input data short ring number 01 ~ 32 item no. Item input data description default 01 frequency 1 00 = ...

  • Page 494: Feature Cross Reference

    Table 2-16 ring cycle table data ring cycle (ms) 01 125 (on) / off 02 125 (on) / 125 (off) / 125 (on) / off 03 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 04 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / 125 (off) / 125 (on) / off 05 250 (on) / off 06 250 (on) / 250 (off)...

  • Page 495: Description

    Program 80 : basic hardware setup for system 80-11 : mfc tone receiver setup level: in description use program 80-11 : mfc tone receiver setup to various data for the mfc signal detection. Input data mfc tone receiver type number 1 = mfc receiver for extension 2 = mfc receiver for trunk 3 = reserved...

  • Page 496: Feature Cross Reference

    Default table 2-18 80-11 default table item name type 1 type 2 type 3 type 4 type 5 01 detect level 0 0 0 0 0 02 start delay time 0 0 0 0 0 03 min. Detect level 15 (- 25 dbm) 15 (- 25 dbm) 15 (- 25 dbm) 15 (- 25 dbm) 15 (- 25 dbm) 04 max. Detect level 0 (0 dbm) 0 (0 dbm) 0 (0 dbm) 0 (0 dbm) 0 (0 dbm...

  • Page 497: Description

    Program 80 : basic hardware setup for system 80-12 : caller id receiver setup level: in description use program 80-12 : caller id receiver setup defines the type and level for caller id detection of dsp. Input data item no. Item input data default 01 type 0 = ntt 1 = other 2 = korea 1 02 level (mark...

  • Page 498: Description

    Program 81 : basic hardware setup for trunk 81-01 : co initial data setup level: in description use program 81-01 : co initial data setup to define the various basic data parameters for the coiu. Input data item no. Item input data default 01 pcm encoding method specifica- tion 0 = μ-law 1 = a-law 1...

  • Page 499: Feature Cross Reference

    Item no. Item input data default 23 loop disconnect detect maximum time 1 ~ 255 (10 ~ 2550 ms) 70 (700 ms) 27 dial pulse break time (10pps) 1 ~ 255 (5 ~ 1275 ms) 13 (65 ms) 28 dial pulse make time (10pps) 1 ~ 255 (5 ~ 1275 ms) 7 (35 ms) 29 dp inter-digit time (10pps) 1 ~ 255 (10 ~ 2550 ms) 61 (610 m...

  • Page 500: Description

    Program 81 : basic hardware setup for trunk 81-04 : isdn bri layer 1 (t-point) initial data setup level: mf description use program 81-04 : isdn bri layer 1 (t-point) initial data setup to define the various basic data for layer 1 of isdn bri. Input data item no. Item input data default 01 wait time...

  • Page 501: Description

    Program 81 : basic hardware setup for trunk 81-05 : isdn bri & pri layer 2 (t-point) initial data setup level: mf description use program 81-05 : isdn bri & pri layer 2 (t-point) initial data setup to define the various basic data for layer 2 of isdn bri and pri. Input data item no. Item input data ...

  • Page 502: Description

    Program 81 : basic hardware setup for trunk 81-06 : isdn bri & pri layer 3 (t-point) timer setup level: in description use program 81-06 : isdn bri & pri layer 3 (t-point) timer setup to define the various basic timers for layer 3 of isdn bri/pri (defined in program 10-03-04). Input data layer 3 tim...

  • Page 503: Feature Cross Reference

    Item no. Item input data description default 11 t312 1 ~ 254 seconds specifies the timer value in 1/100ths of a second of the timer to be started when setup is sent or re-sent on broadcast da- ta link. This timer is only valid for network side use only. 6 12 t313 1 ~ 254 seconds specifies the timer ...

  • Page 504: Description

    Program 81 : basic hardware setup for trunk 81-07 : codec filter setup for analog trunk port level: in description use program 81-07 : codec filter setup for analog trunk port to define the codec (qslac) filter for each analog trunk port. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl...

  • Page 505: 81-08 : T1 Trunk Timer Setup

    Program 81 : basic hardware setup for trunk 81-08 : t1 trunk timer setup level: in description use program 81-08 : t1 trunk timer setup to define the basic timer setting of each t1 trunk type. Input data item no. Item input data default 01 answer signal detection time (loop) 1 ~ 250 (4 ms ~ 1000 ms)...

  • Page 506

    Item no. Item input data default 20 ringing signal stop detection time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 50 (5000 ms) 21 loop current detection time (loop) 1 ~ 250 (4 ms ~ 1000 ms) 40 (160 ms) 22 loop current detection time (ground) 1 ~ 250 (4 ms ~ 1000 ms) 40 (160 ms) 23 loop current detection time...

  • Page 507: Feature Cross Reference

    Item no. Item input data default 54 receive hookflash duration min. Time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 3 (300 ms) 55 receive hookflash duration max. Time (opx) 1 ~ 255 (100 ms ~ 25500 ms) 6 (600 ms) 56 loop off guard time (loop) 1 ~ 255 (100 ms ~ 25500 ms) 20 (2000 ms) 57 loop off guard time (gr...

  • Page 508: Description

    Program 81 : basic hardware setup for trunk 81-09 : cot codec (qslac) filter setting level: in description use program 81-09 : cot codec (qslac) filter setting to define the filter setting data (when program 81-07 is set to 4). Input data item no. Item input data default 01 b1 filter setup (1) 0 ~ 2...

  • Page 509: Feature Cross Reference

    Item no. Item input data default 30 z filter coefficients (13) 0 ~ 255 84 31 z filter coefficients (14) 0 ~ 255 31 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 170 34 r filter coefficients (2) 0 ~ 255 192 35 r filter coefficients (3) 0 ~ 255 187 36 r filter coefficien...

  • Page 510: 81-13 : E1 Trunk Timer Setup

    Program 81 : basic hardware setup for trunk 81-13 : e1 trunk timer setup level: in description use program 81-13 : e1 trunk timer setup to define the basic timer setting of e1 trunk. Input data trunk port number 001 ~ 126 (sl1000) 001 ~ 096 (sl1100) item no. Item input data default 01 loop current d...

  • Page 511: Feature Cross Reference

    Item no. Item input data default 34 receive digit acknowledge min time 1 ~ 255 (4 ms ~ 1020 ms) 25 (100 ms) 35 receive digit acknowledge max time 1 ~ 255 (4 ms ~ 1020 ms) 75 (300 ms) 36 receive meter pulse min time 1 ~ 255 (4 ms ~ 1020 ms) 25 (100 ms) 37 receive meter pulse max time 1 ~ 255 (4 ms ~ ...

  • Page 512: Extension

    Program 82 : basic hardware setup for extension 82-01 : incoming ring tone level: in description use program 82-01 : incoming ring tone to set the incoming ring tones, which are the tones a user hears when a call rings an extension. These tones are grouped into four ring tone ranges (1 ~ 4), also ca...

  • Page 513: Feature Cross Reference

    Item no. Item input data default 03 modulation 0 = no modulation 1 = 8 hz modulation 2 = 16 hz modulation 3 = envelope refer below default table 2-19 82-01 default table incoming ringing tone number tone type frequency 1 (hz) frequency 2 (hz) modulation pattern 1 (trunk incoming) high mid low 1100 h...

  • Page 514: Extension

    Program 82 : basic hardware setup for extension 82-02 : key telephone led pattern setup (sl1000) level: mf description use program 82-02 : key telephone led pattern setup to setup the led flashing pattern. Input data item no. Item input data description default 01 led01 0 ~ 7 incoming extension/trun...

  • Page 515: Feature Cross Reference

    Pattern #0 0 1 0 1 0 1 0 1 0 1 0 000 pattern #1 1 1 0 0 0 1 1 0 0 0 001 pattern #2 1 0 1 0 0 1 0 1 0 0 010 pattern #3 1 1 1 1 0 1 1 1 1 0 011 pattern #4 1 0 1 0 1 0 0 0 0 0 100 pattern #5 1 0 0 0 0 0 0 0 0 0 101 pattern #6 1 0 1 0 0 0 0 0 0 0 110 pattern #7 1 1 1 1 1 1 0 1 0 1 111 200 400 600 800 10...

  • Page 516: Extension

    Program 82 : basic hardware setup for extension 82-04 : astu initial data setup level: in description use program 82-04 : astu initial data setup to set the basic data of the slt. Input data item no. Item input data default 01 companding method type 0 = μ-law 1 = a-law 1 02 ringing frequency 0 = 25 ...

  • Page 517: Extension

    Program 82 : basic hardware setup for extension 82-05 : isdn bri & pri layer2 (s-point) initial data setup level: mf description use program 82-05 : isdn bri & pri layer2 (s-point) initial data setup to set the basic data for the layer 2 of isdn bri/pri s-point. Input data item no. Item input data d...

  • Page 518: Extension

    Program 82 : basic hardware setup for extension 82-06 : isdn bri & pri layer3 (s-point) timer setup level: in description use program 82-06 : isdn bri & pri layer3 (s-point) timer setup to set the basic timer for the layer 3 of isdn bri & pri s-point. Input data layer3 timer type no. 1 ~ 5 item no. ...

  • Page 519: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-497 program 82.

  • Page 520: Extension

    Program 82 : basic hardware setup for extension 82-07 : codec filter setup for analog station port level: in description use program 82-07 : codec filter setup for analog station port to set the filter value of the codec (qslac) filter of each analog port. Input data station port number 001 ~ 128 (s...

  • Page 521: Extension

    Program 82 : basic hardware setup for extension 82-08 : sidetone volume setup level: mf description use program 82-08 : sidetone volume setup for adjusting the telephone sidetone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Input data item no...

  • Page 522: Extension

    Program 82 : basic hardware setup for extension 82-09 : sliu codec filter data setup level: in description use program 82-09 : sliu codec filter data setup to define the filter setting data (when program 82-07 is set to 4). Input data item no. Item input data default 01 b1 filter setup (1) 0 ~ 255 1...

  • Page 523

    Item no. Item input data default 28 z filter coefficients (11) 0 ~ 255 43 29 z filter coefficients (12) 0 ~ 255 169 30 z filter coefficients (13) 0 ~ 255 166 31 z filter coefficients (14) 0 ~ 255 159 32 z filter coefficients (15) 0 ~ 255 1 33 r filter coefficients (1) 0 ~ 255 220 34 r filter coeffic...

  • Page 524: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-502 program 82 : basic hardware setup for extension program 82.

  • Page 525: Extension

    Program 82 : basic hardware setup for extension 82-13 : volume level data setup for txd tel2 [lkts] (sl1000) level: in description use program 82-13 : volume level data setup for txd tel2 to defines each volume type in the speaker, and the group listening for txd tel2. Volume type means “small volum...

  • Page 526: Extension

    Program 82 : basic hardware setup for extension 82-14 : handset/headset gain setup for multi line telephone level: in description use program 82-14: handset/headset gain setup for multi line telephone to define the handset/ headset gain level for multi line telephone. Input data extension number up ...

  • Page 527: Extension

    Program 82 : basic hardware setup for extension 82-18 : kst codec filter data setup (sl1000) level: in description use program 82-18 : kst codec filter data setup to defines the codec (qslac) filter for each kst station port. Input data station port number 001 ~ 128 item no. Item input data descript...

  • Page 528: Extension

    Program 82 : basic hardware setup for extension 82-19 : kst codec filter data setup (sl1000) level: in description use program 82-19 : kst codec filter data setup to defines the kst codec (qslac) filter data. Input data item no. Item input data description default 01 b1 filter setup (1) 0 ~ 255 * th...

  • Page 529

    Item no. Item input data description default 24 z filter coefficients (7) 0 ~ 255 194 25 z filter coefficients (8) 0 ~ 255 43 26 z filter coefficients (9) 0 ~ 255 106 27 z filter coefficients (10) 0 ~ 255 163 28 z filter coefficients (11) 0 ~ 255 43 29 z filter coefficients (12) 0 ~ 255 169 30 z fil...

  • Page 530: Feature Cross Reference

    Item no. Item input data description default 50 x filter coefficients (4) 0 ~ 255 144 51 x filter coefficients (5) 0 ~ 255 1 52 x filter coefficients (6) 0 ~ 255 144 53 x filter coefficients (7) 0 ~ 255 1 54 x filter coefficients (8) 0 ~ 255 144 55 x filter coefficients (9) 0 ~ 255 1 56 x filter coe...

  • Page 531: Extension

    Program 82 : basic hardware setup for extension 82-20 : volume level data setup for kst (sl1000) level: in description use program 82-20 : volume level data setup for kst to defines each volume type of the speaker, and the group listening for kst. Volume type means “small volume, middle volume (1), ...

  • Page 532: Extension

    Program 82 : basic hardware setup for extension 82-21 : sensor setup level: in description use program 82-21 : sensor setup to setup the sensor for sl1000/sl1100. Input data sensor number 1 ~ 8 (sl1000) 1 ~ 6 (sl1100) item no. Item input data description default 01 sensor type 0 = close detect 1 = o...

  • Page 533: Description

    Program 84 : hardware setup for voipdb 84-01 : h.323 trunk basic information setup level: in description use program 84-01 : h.323 trunk basic information setup to set the basic information of the h.323 trunk. Input data item no. Item input data description default 02 number of g.711 au- dio frames ...

  • Page 534

    Item no. Item input data description default 22 vad threshold 1 ~ 30 (- 19 db ~ + 10 db and self adjustment) 1 = - 19 db (- 49 dbm) : 20 = 0 db (- 30 dbm) : 29 = 9 db (- 21 dbm) 30 = 10 db (- 20 dbm) 20 33 priority codec set- ting 0 ~ 3 0 = g711_pt 1 = g723_pt 2 = g729_pt 3 = g722_pt priority of voi...

  • Page 535: Feature Cross Reference

    Item no. Item input data description default 71 dtmf level low 1 = - 33 dbm : 28 = - 6 dbm 28 conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-513 program 84.

  • Page 536: Description

    Program 84 : hardware setup for voipdb 84-02 : h.225 and h.245 information basic setup level: in description use program 84-02 : h.225 and h.245 information basic setup to define the basic setup information of h.225 and h.245. Input data item no. Item input data default 01 h.225 alerting time 0 ~ 25...

  • Page 537: Feature Cross Reference

    Item no. Item input data default 29 ras lrq timer 0 ~ 255 seconds 5 30 lrq retry count 0 ~ 255 2 31 ras rai timer 0 ~ 255 seconds 3 32 rai retry count 0 ~ 255 2 33 call signaling port number 0 ~ 65535 : 0 ~ 1719, 1721 ~ 65535 1730 35 fast start mode 0 = disable 1 = enable 1 36 ras unicast port numbe...

  • Page 538: Description

    Program 84 : hardware setup for voipdb 84-07 : firmware download setup level: in description use program 84-07 : firmware download setup to configure the settings related to central firmware download for ip phones. Input data item no. Item input data description default 01 server mode 0 = tftp 1 = f...

  • Page 539: 84-09 : Vlan Setup

    Program 84 : hardware setup for voipdb 84-09 : vlan setup level: in description use program 84-09 : vlan setup to set up the vlan data. I/f no.2 the packets send from lan i/f on voipdb is set the vlan tag. Input data interface number 1 ~ 2 item no. Item input data default 01 vlan 0 = disable (off) 1...

  • Page 540: 84-10 : Tos Setup

    Program 84 : hardware setup for voipdb 84-10 : tos setup level: in description use program 84-10 : tos setup to set up the type of service data. Input data protocol type 1 ~ 3 = not used 4 = h.323 5 = rtp/rtcp 6 = sip 7 = not used 8 = sip-mlt 9 = sip trunk 10 = not used item no. Item input data desc...

  • Page 541: Description

    Program 84 : hardware setup for voipdb 84-13 : sip trunk codec information basic setup level: in description use program 84-13 : sip trunk codec information basic setup to set up the basic codec options for sip trunks. Input data item no. Item input data description default related program 01 number...

  • Page 542

    Item no. Item input data description default related program 15 g.723 jitter buf- fer - standard 0 ~ 300 ms set the average value of the g.723 jitter buffer. 60 16 g.723 jitter buf- fer - maximum 0 ~ 300 ms set the maximum value of the g. 723 jitter buffer. 120 17 jitter buffer mode 1 = static 3 = a...

  • Page 543

    Item no. Item input data description default related program 40 g.726 jitter buf- fer - minimum 0 ~ 255 ms set the minimum value of the jitter buffer of g.726 is set. Jitter is the variation in the time between pack- ets arriving and the buffer allows this variation to be absorbed. 30 41 g.726 jitte...

  • Page 544: Feature Cross Reference

    Item no. Item input data description default related program 65 vad negotiation on sdp (v2.0 added) 0 = disable 1 = enable this prg is used to determine the vad determination method setting vad information on sdp. This prg is effective when vad is enabled on each codec. G.711 and g.729 are targets a...

  • Page 545: Description

    Program 84 : hardware setup for voipdb 84-14 : sip trunk basic information setup level: in description use program 84-14 : sip trunk basic information setup to define the basic setup for sip trunks. Input data item no. Item input data description default 01 invite retx count 0 ~ 255 specifies the nu...

  • Page 546: Feature Cross Reference

    Conditions none feature cross reference none sl1000/sl1100 issue 3.01 2-524 program 84 : hardware setup for voipdb program 84.

  • Page 547: Description

    Program 84 : hardware setup for voipdb 84-15 : h.323/sip phone keep alive setup level: in description use program 84-15 : h.323/sip phone keep alive setup to set the keep alive configuration of the h.323/sip phone. Input data item no. Item input data description default 01 registration informa- tion...

  • Page 548: Description

    Program 84 : hardware setup for voipdb 84-16 : voipdb limiter control gain setup level: in description use program 84-16 : voipdb limiter control gain setup to set the limiter control gain configuration of voipdb. Input data item no. Item input data description default 01 rx limiter control gain 0 ~...

  • Page 549: Feature Cross Reference

    Feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-527 program 84.

  • Page 550: Description

    Program 84 : hardware setup for voipdb 84-19 : sip extension codec information basic setup level: in description use program 84-19 : sip extension codec information basic setup to define the codec information for the sip extensions. Input data item no. Item input data description default 01 number o...

  • Page 551

    Item no. Item input data description default 16 g.723 jitter buffer - maximum 0 ~ 300 ms set the maximum value of the g.723 jitter buffer. 120 17 jitter buffer mode 1 = static 3 = adaptive immediately set the mode of the jitter buffer. 1 = size set to the fixed amount for the co- dec. 2 = the minimu...

  • Page 552: Feature Cross Reference

    Item no. Item input data description default 42 g.726 jitter buffer - maximum 0 ~ 255 ms set the maximum g.726 jitter buffer. 120 43 ilbc audio frame 2 = 20 ms 3 = 30 ms 4 = 40 ms maximum number of ilbc audio frames. Ilbc assumes the frame of 10ms is a unit. 3 45 ilbc jitter buffer - minimum 0 ~ 255...

  • Page 553: Description

    Program 84 : hardware setup for voipdb 84-20 : sip extension basic information setup level: in description use program 84-20 : sip extension basic information setup to set up proxy information, session timers, called party information and expire value of invite. Input data item no. Item input data d...

  • Page 554: Description

    Program 84 : hardware setup for voipdb 84-22 : dr700 multiline logon information setup level: sa description use program 84-22 : dr700 multiline logon information setup to set the dr700 multiline logon information. Input data personal id index 001 ~ 128 (sl1000) 001 ~ 120 (sl1100) item no. Item inpu...

  • Page 555: Description

    Program 84 : hardware setup for voipdb 84-23 : dr700 multiline basic information setup level: in description use program 84-23 : dr700 multiline basic information setup to set the basic information for the dr700 multiline terminal. Input data item no. Item input data description default 01 registrat...

  • Page 556: Feature Cross Reference

    Item no. Item input data description default 14 refer expire timer 0 ~ 65535 seconds 60 conditions none feature cross reference none sl1000/sl1100 issue 3.01 2-534 program 84 : hardware setup for voipdb program 84.

  • Page 557: Description

    Program 84 : hardware setup for voipdb 84-24 : dr700 multiline codec basic information setup level: in description use program 84-24 : dr700 multiline codec basic information setup to set the codec of each type of dr700 multiline telephone. Input data type 1 = type 1 2 = type 2 3 = type 3 4 = type 4...

  • Page 558

    Item no. Item input data description default 08 g.729 silence com- pression (vad) mode 0 = disable 1 = enable select whether to compress silence with g.729. When there is silence, the rtp packet is not sent. When vad is enabled the cpu will stop sending silence packets but the ip phone will continue...

  • Page 559: Feature Cross Reference

    Item no. Item input data description default 38 dtmf level mode 0 = use the default of voipdb unit 1 = use the main sys- tem 0 39 dtmf level high 1 = - 33 dbm : 28 = - 6 dbm 28 40 dtmf level low 1 = - 33 dbm : 28 = - 6 dbm 28 conditions none feature cross reference none issue 3.01 sl1000/sl1100 prog...

  • Page 560: Description

    Program 84 : hardware setup for voipdb 84-26 : voip basic setup (dsp) level: in description use program 84-26 : voip basic setup to set the ip address and the port of voip. Input data slot number 0 voipdb gw number gw number will not be shown in telephone programming mode. 1 item no. Item input data...

  • Page 561: 84-27 : Voip Basic Setup

    Program 84 : hardware setup for voipdb 84-27 : voip basic setup level: in description use program 84-27 : voip basic setup to set the dtmf relay and the srtp mode of the voipdb. Input data slot number 0 item no. Item input data description default 01 dtmf relay setup 0 = dtmf relay disa- bled 1 = in...

  • Page 562: Feature Cross Reference

    Item no. Item input data description default 14 icmp redirect 0 = enabled, voice packets will follow icmp redirect messages. 1 = disabled, voice packets will not follow the icmp redirect mes- sage. 1 15 dtmf detect mini- mum duration 23 ~ 2000 ms this setting is the minimal time setting to distingui...

  • Page 563: Description

    Program 84 : hardware setup for voipdb 84-28 : dr700 multiline firmware name setup level: in description use program 84-28 : dr700 multiline firmware name setup to set the firmware name to download for the ip phone. Input data terminal type 1 ~ 3 = not used 4 = ip4ww-24tixh item no. Item input data ...

  • Page 564: Description

    Program 84 : hardware setup for voipdb 84-29 : sip-mlt codec information fixed mode setup level: in description use program 84-29 : sip-mlt codec information fixed mode setup to set the codec data of the sip-mlt when it uses multicast. Input data type 1 = type 1 (multicast) 2 = type 2 (reserved) 3 =...

  • Page 565: Description

    Program 84 : hardware setup for voipdb 84-31 : voipdb echo canceller setup level: in description use program 84-31 : voipdb echo canceller setup to sets voipdb echo canceller value. Input data type 1 = h.323 trunk 2 ~ 7 = not used 8 = sip trunk 9 = sip extension 10 = not used 11 = dr700 type 1 12 = ...

  • Page 566

    Item no. Item input data description default related program 08 tdm echo can- celler echo type 0 = disable 1 = line echo cancel- ler 2 = acoustic echo can- celler 1 09 tdm max erle (v2.0 added) 0 ~ 6 (- 9 db ~ 9 db) 0 = - 9 db 1 = - 6 db 2 = - 3 db : 5 = 6 db 6 = 9 db do not change the setting unles...

  • Page 567

    Item no. Item input data description default related program 18 tdm rx automa- ticlevelcontrol level (v2.0 add- ed) 0 ~ 12 (- 42 ~ - 6 dbm) 0 = - 42 dbm 1 = - 39 dbm : 7 = - 21 dbm : 11 = - 9 dbm 12 = - 6 dbm do not change the setting unless asked to change by engineer. Select target gain. Effective...

  • Page 568

    Item no. Item input data description default related program 29 rtp tx level control level 0 ~ 16 (- 24 ~ 24 db) 0 = - 24 db 1 = - 21 db 2 = - 18 db : 8 = 0 db : 14 = 18 db 15 = 21 db 16 = 24 db 8 30 rtp tx automa- ticlevelcontrol level (v2.0 add- ed) 0 ~ 12 (- 42 dbm~ - 6 dbm) 0 = - 42 dbm 1 = - 39...

  • Page 569: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-547 program 84.

  • Page 570: 90-01 : Installation Date

    Program 90 : maintenance program 90-01 : installation date level: in description use program 90-01 : installation date to define the installation date of the system. Input data item no. Item input data default 01 year 00 ~ 99 00 (no setting) 02 month 01 ~ 12 00 (no setting) 03 day 01 ~ 31 00 (no set...

  • Page 571: Description

    Program 90 : maintenance program 90-02 : programming password setup level: in description use program 90-02 : programming password setup to set the system passwords. For password entry, the system allows eight users to be defined. Each user can have a: • unique alphanumeric name (up to 10 alphanumer...

  • Page 572: Feature Cross Reference

    User no. User name password level level description 5 user1 1111 5 (ua) user programming administer mode lev- el 1 conditions • more than one extension can be in the programming mode. Feature cross reference none sl1000/sl1100 issue 3.01 2-550 program 90 : maintenance program program 90

  • Page 573: 90-03 : Save Data

    Program 90 : maintenance program 90-03 : save data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-03 : save data to save the programmed data on the cf card. This program should be used after changing the programmed ...

  • Page 574: 90-04 : Load Data

    Program 90 : maintenance program 90-04 : load data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-04 : load data to load the system data from the inserted cf card into the pz-vm21 daughter board installed to the sys...

  • Page 575: 90-05 : Slot Control

    Program 90 : maintenance program 90-05 : slot control level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-05 : slot control to reset or delete (uninstall) units (slots 1 ~ 16 (sl1000) 0 ~ 9 (sl1100)). Delete allows you...

  • Page 576: 90-06 : Trunk Control

    Program 90 : maintenance program 90-06 : trunk control level: sa description use program 90-06 : trunk control for trunk maintenance. Busy out lets you block a unit from placing outgoing calls (just like placing the unit switch down). Once busied out, none of the ports on the unit can be used for ne...

  • Page 577: 90-07 : Station Control

    Program 90 : maintenance program 90-07 : station control level: sa description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-07 : station control for extension maintenance. Input data menu number 1 = hardware reset 2 = software reset ...

  • Page 578: 90-08 : System Reset

    Program 90 : maintenance program 90-08 : system reset level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-08 : system reset to perform a system reset. Input data item no. Item input data default 01 system reset dial 1 + ...

  • Page 579: Description

    Program 90 : maintenance program 90-09 : automatic system reset time setup level: in description use program 90-09 : automatic system reset time setup to define the time for the system to automatically reset. Input data item no. Item input data default 01 month 00 ~ 12 if the month is set to 00 and ...

  • Page 580: 90-10 : System Alarm Setup

    Program 90 : maintenance program 90-10 : system alarm setup level: in description use program 90-10 : system alarm setup to assign a status to system alarms. You can designate an alarm as major or minor. This program also assigns whether or not the alarm information is reported to the pre-defined de...

  • Page 581

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 3 2 0 connec- tion fault between cpu and other pkgs. The error occur- red when com- municating with the package. When the pack- age is broken, it recognizes it as a communica- tion fault. 1. The unit is not completely i...

  • Page 582

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 6 0 0 blocking the link of ter- minals connec- ted with the esi package came off. 1. Terminal breakdown. 2. Faulty wiring and wiring ter- mination. 3. External noise. 4. Esi package breakdown. Confirm the termi- nal con...

  • Page 583

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 30 2 0 smdr buffer full the temporary buffer for smdr in main device overflowed, and a part of output smdr data dis- appeared be- cause it could not output smdr data. 1. Problem of wiring to con- nect main de- vice with...

  • Page 584

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 59 2 0 network- ing port limit ex- ceeded (v1.5 added) total number of ports exceeded the limit of 168 ports in the net- work. • new extension or trunk ports are added. • a new system is added in pro- gram 10-27-01. • a...

  • Page 585

    Alarm no. Type re- port name content of alarm cause action recovery alarm status 63 0 0 sip-mlt trouble in- formation. 1. The trouble occurred by the sip- mlt rela- tion. 2. The dsp resource could not be acquired at incom- ing/outgo- ing. 3. The nego- tiation with voipdb failed. 1. The packet loss o...

  • Page 586: Feature Cross Reference

    Feature cross reference none sl1000/sl1100 issue 3.01 2-564 program 90 : maintenance program program 90

  • Page 587: 90-11 : System Alarm Report

    Program 90 : maintenance program 90-11 : system alarm report level: in description use program 90-11 : system alarm report to define the details of the system alarm report. Input data item no. Item input data description default related program 02 report method 0 = no report 1 = e-mail address when ...

  • Page 588: Feature Cross Reference

    Item no. Item input data description default related program 15 dimlog notifica- tion (v2.0 added) 0 = no 1 = yes prg 90-11-14=yes (prg 47-18 smtp client uses) and cf mount are necessary. In the case of system fault, dim- last.Gz and dimdump.Gz are noti- fied. 0 90-11-14 conditions none feature cros...

  • Page 589: 90-12 : System Alarm Output

    Program 90 : maintenance program 90-12 : system alarm output level: in description use program 90-12 : system alarm output to set the options for the alarm report. This program has six separate menu options. Define the output port to be used as the output for system alarm report and set the system a...

  • Page 590: Description

    Program 90 : maintenance program 90-13 : system information output level: in description use program 90-13 : system information output to define the output port to be used as the system information output. Input data item no. Item input data description default 01 output port type 0 = no setting 5 =...

  • Page 591: Description

    Program 90 : maintenance program 90-16 : main software information level: in description use program 90-16 : main software information to display the main software information on the cpu. Input data item no. Item input data default 01 version number read only: 01.00 ~ 99.99 ascii code (5 bytes) 02 s...

  • Page 592: 90-17 : Firmware Information

    Program 90 : maintenance program 90-17 : firmware information level: in description use program 90-17 : firmware information to display the firmware versions of the various system units. Input data item no. Item input data default 01 dsp firmware version no. Read only: 00.00.00.00 ~ 15.15.15.15 bcd ...

  • Page 593: 90-19 : Dial Block Release

    Program 90 : maintenance program 90-19 : dial block release level: sa description note: this program is available via telephone programming and webpro not through pc programming. When the extension number is entered in program 90-19 : dial block release, the extension is released from the dial block...

  • Page 594: Description

    Program 90 : maintenance program 90-20 : traffic report data setup level: in description use program 90-20 : traffic report data setup to define the details of the traffic report. Input data item no. Item input data description default 01 call traffic output 0 = not measured 1 = measure 0 03 all lin...

  • Page 595: Feature Cross Reference

    Feature cross reference • traffic reports issue 3.01 sl1000/sl1100 programming manual 2-573 program 90

  • Page 596: Description

    Program 90 : maintenance program 90-21 : traffic report output level: in description use program 90-21 : traffic report output to define the output port to be used as the traffic report output. Input data item no. Item input data default 01 output port type 0 = no setting 3 = lan 0 conditions none f...

  • Page 597: Description

    Program 90 : maintenance program 90-23 : deleting registration of ip telephones level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-23 : deleting registration of ip telephones to delete the registered ip telephone from...

  • Page 598: Description

    Program 90 : maintenance program 90-24 : system alarm report notification time setup level: in description use program 90-24 : system alarm report notification time setup to set the date and time for the alarm report to print. Input data notification number 1 ~ 12 item no. Item input data default 01...

  • Page 599: Description

    Program 90 : maintenance program 90-25 : system alarm report cc mail setup level: in description use program 90-25 : system alarm report cc mail setup to define the mail address to receive the system alarm report cc mail setup. Input data cc number 1 ~ 5 item no. Item input data default 01 cc mail a...

  • Page 600: Description

    Program 90 : maintenance program 90-26 : program access level setup level: in description use program 90-26 : program access level setup to define the password access level required to change a system program. Input data program numbers 1001 ~ 9903 item no. Item input data default 01 maintenance lev...

  • Page 601: Description

    Program 90 : maintenance program 90-28 : user programming password setup level: in description use program 90-28 : user programming password setup to set the password used to enter the user programming mode. Input data extension numbers maximum four digits (sl1000) maximum eight digits (sl1100) item...

  • Page 602: Description

    Program 90 : maintenance program 90-31 : dim access over ethernet level: in description use program 90-31 : dim access over ethernet to enable dim (diagnostic information maintenance) access over the lan, and to define the user name and password. Dim is a maintenance tool used by engineering to extr...

  • Page 603: Description

    Program 90 : maintenance program 90-33 : preselected data setup level: in description note: this program is available only via telephone programming and not through pc programming. Use 90-33 : preselected data setup to setup the system to preselected setting. Input data item no. Item input data defa...

  • Page 604

    Program no. Name default 21-03-01 trunk group routing for trunks 1 (all trunks : all modes : group1) 22-01-03 incoming ring no answer alarm start timer 30 22-01-04 normal dil incoming no answer timer 30 22-01-08 did (ddi) pilot call no answer timer 30 22-08-01 second irg setup for unanswered 1 (all ...

  • Page 605

    Program no. Name default 80-01-02 basic tone no 1 (svc tone 2 unit 1) 12-01-02 automatic night mode switch 0 20-02-07 display mode of date and time 8 20-02-09 disconnect supervision 1 20-02-12 mode setting for incoming call from extension 1 20-07-11 force trunk disconnection (analog trunk only) 1 (c...

  • Page 606

    Program no. Name default 40-07-01 voice prompt language assignment for system based 7 47-02-16 voice prompt language 7 47-06-14 voice prompt language 7 47-07-03 prompt language 7 47-10-03 voice prompt language 7 taiwan program no. Name default 15-01-01 extension name - (delete all station name) 20-0...

  • Page 607

    Program no. Name default 15-03-03 terminal type 1 (all stations) 21-01-06 dial pause at first digit 1 20-13-01 long conversation alarm 0 (class 1 only) 20-13-22 called party status 1 (class 1 only) 20-09-04 notification for incoming call list existence 0 (class 1 only) 14-02-18 busy tone detection o...

  • Page 608

    Program no. Name default 20-03-04 trunk call dial sending time by slt 1 25-02-01 did/disa talkie to assign the vrs message num- ber trunks 1 ~ 27 talkie = 1 mode 1 data = 1 (day mode) mode 2 data = 2 (night mode) 25-05-01 vrs/disa error message assignment 4 (trunks 1 ~ 27 mode 1, 2) 40-10-08 call at...

  • Page 609

    Program no. Name default 14-02-05 dtd-manual dl 0 14-02-09 busy tone detection 1 14-02-10 caller id 1 14-02-18 busy tone detection talking 1 15-01-01 extension name - 15-03-09 extension display 1 15-03-15 hook disconnect mode 1 16-01-03 auto step call 1 16-01-04 hunting mode 1 16-01-08 max queue no ...

  • Page 610

    Program no. Name default 24-02-03 cfw not answer time 15 24-02-04 trf recall time 15 25-01-02 without password 0 25-07-01 vrs dial time 5 25-07-02 disa no answer time 60 25-07-03 disa disconnect retransfer to irg 30 31-02-01 internal paging group 1 31-02-02 internal all paging group 1 32-01-02 door ...

  • Page 611

    Program no. Name default 20-03-04 trunk call dial sending time by slt 1 20-07-01 manual night service enabled 1 (class 1 only) 20-13-01 long conversation alarm 0 (class 1 only) 20-13-22 called party status 1 (class 1 only) 20-17-01 operator extension number 200 20-19-02 caller id wait timer 0 21-01-...

  • Page 612

    Program no. Name default 12-02-01 automatic night service pattern (time pattern 1) set time 05 = s 1700, e 0000, m2 modegrp 1 12-02-01 automatic night service pattern (time pattern 2) set time 01 = s 0000, e 0800, m2 modegrp 1 12-02-01 automatic night service pattern (time pattern 2) set time 02 = s...

  • Page 613

    Program no. Name default 15-02-12 off hook signaling type 4 (all stations) 15-02-33 multi language calendar display on lcd 1 (all stations) 15-02-34 call register mode 1 (all stations) 15-03-11 caller id type 1 (all stations) 15-03-12 fixed cadence 0 (all stations) 15-07-01 programmable function key...

  • Page 614

    Program no. Name default dial analysis table number 151 00@@@@@@@@@@ dial analysis table number 152 01@@@@@@@@@@ dial analysis table number 153 02@@@@@@@@@@ dial analysis table number 154 03@@@@@@@@@@ dial analysis table number 155 04@@@@@@@@@@ dial analysis table number 156 05@@@@@@@@@@ dial analys...

  • Page 615

    Program no. Name default dial analysis table number 194 97@@@@@ dial analysis table number 195 98@@@@@ dial analysis table number 196 99@@@@@ 26-02-02 service type dial analysis table number 151 1 dial analysis table number 152 1 dial analysis table number 153 1 dial analysis table number 154 1 dial...

  • Page 616

    Program no. Name default dial analysis table number 190 1 dial analysis table number 191 1 dial analysis table number 192 1 dial analysis table number 193 1 dial analysis table number 194 1 dial analysis table number 195 1 dial analysis table number 196 1 26-02-03 additional data dial analysis table...

  • Page 617

    Program no. Name default dial analysis table number 186 10 dial analysis table number 187 10 dial analysis table number 188 10 dial analysis table number 189 10 dial analysis table number 190 10 dial analysis table number 191 10 dial analysis table number 192 10 dial analysis table number 193 10 dia...

  • Page 618

    Program no. Name default 34-11-01 e1 trunk type 8 (trk 04 ~ 126) 34-11-02 mfc dialing type 3 (trk 04 ~ 126) 34-11-03 mfc group b 1 (trk 04 ~ 126) 34-11-04 expected number of mfc digits 3 (trk 04 ~ 126) 35-01-01 output port type 1 (port 1 only) 35-01-04 omit digits 0 (port 1 only) 35-02-09 extension ...

  • Page 619: Feature Cross Reference

    Service tone setup unit 80-01-01 80-01-02 80-01-03 80-01-04 ring back tone tone 14 1 0 0 40 32 2 - 1 10 32 external ring back tone tone 45 1 0 0 40 32 2 - 1 10 32 3 - - - - 4 - - - - external busy tone tone 46 1 0 0 2 32 2 0 1 2 32 malaysia program no. Name default 10-02-01 country code 60 thailand ...

  • Page 620: 90-34 : Firmware Information

    Program 90 : maintenance program 90-34 : firmware information level: in description use program 90-34 : firmware information to list the package type and firmware units installed in the system. Input data slot number 00 ~ 16 (sl1000) 00 ~ 09 (sl1100) item no. Item input data default 01 package name ...

  • Page 621: Description

    Program 90 : maintenance program 90-35 : wizard programming level setup level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-35 : wizard programming level setup to set the maintenance level for wizard programming. Input d...

  • Page 622: Description

    Program 90 : maintenance program 90-36 : firmware update time setting level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-36 : firmware update time setting to define the data for the firmware update feature. This data is...

  • Page 623: Feature Cross Reference

    Conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming manual 2-601 program 90

  • Page 624: Description

    Program 90 : maintenance program 90-38 : user programming data level setup level: in description use program 90-38 : user programming data level setup sets system data to turn on/off each user programming feature. Input data item no. Item input data default related program 01 time setting 0 = turn o...

  • Page 625: Feature Cross Reference

    Item no. Item input data default related program 18 call forward-immediate/no answer /both ring 0 = turn off 1 = turn on 1 = turn on 11-11-01 11-11-03 11-11-05 19 call forward-busy 0 = turn off 1 = turn on 1 = turn on 11-11-02 20 trunk incoming ring tone 0 = turn off 1 = turn on 1 = turn on 11-11-20...

  • Page 626: Description

    Program 90 : maintenance program 90-39 : virtual loop back port reset level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-39 : virtual loop back port reset to reset to initial status. Input data item no. Item input data ...

  • Page 627: Description

    Program 90 : maintenance program 90-41 : server setting to update terminal local data level: in description use program 90-41 : server setting to update terminal local data to define the primary dns server address, the secondary dns server address and the data roaming server address. Input data serv...

  • Page 628: Description

    Program 90 : maintenance program 90-42 : dr700 multiline terminal version information level: in description use program 90-42 : dr700 multiline terminal version information to set the hardware version and firmware version of the dr700 mlt terminal. Input data terminal type 1 ~ 3 = not used 4 = ip4ww...

  • Page 629: Description

    Program 90 : maintenance program 90-43 : deleting terminal license of dr700 level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-43 : deleting terminal license of dr700 to delete the terminal license information delivered...

  • Page 630: Description

    Program 90 : maintenance program 90-44 : deleting terminal license of tcp interface level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-44 : deleting terminal license of tcp interface to delete the terminal license infor...

  • Page 631: Telephone

    Program 90 : maintenance program 90-45 : temporary password change for multiline telephone level: in description note: this program is available via telephone programming and webpro not through pc programming. Use program 90-45 : temporary password change for multiline telephone to change the tempor...

  • Page 632: Description

    Program 90 : maintenance program 90-50 : system alarm display setup level: in description use program 90-50 : system alarm display setup to set the system alarm report display. Input data index number 01 ~ 50 item no. Item input data default 01 system alarm display telephone up to four digits (sl100...

  • Page 633: Description

    Program 90 : maintenance program 90-51 : alarm setup for maintenance exchange level: in description use program 90-51 : alarm setup for maintenance exchange to set the day for the maintenance exchange of parts that need regular maintenance. Input data index 1 ~ 10 item no. Item input data default 01...

  • Page 634: 90-52 : System Alarm Save

    Program 90 : maintenance program 90-52 : system alarm save level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-52 : system alarm save for the system alarm output operation. Input data item no. Item input data default 01 ...

  • Page 635: 90-53 : System Alarm Clear

    Program 90 : maintenance program 90-53 : system alarm clear level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-53 : system alarm clear to clear the system alarm. Input data item no. Item input data default 01 clear all ...

  • Page 636: 90-54 : Pc/web Programming

    Program 90 : maintenance program 90-54 : pc/web programming level: in description use program 90-54 : pc/web programming sets parameters for pc and web programming. Input data item no. Item input data description default 01 web pro tcp port number 1 ~ 65535 the port number of tcp of the web pro- gra...

  • Page 637: 90-55 : Free License Select

    Program 90 : maintenance program 90-55 : free license select level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-55 : free license select to validate the free license. Input data item no. Item input data default 01 start...

  • Page 638: 90-56 : Ntp Setup

    Program 90 : maintenance program 90-56 : ntp setup level: in description use program 90-56 : ntp setup to set the ntp. Input data item no. Item input data default 01 ntp synchronize 0 = no 1 = yes 0 02 server address ipv4 form : xxx.Xxx.Xxx.Xxx ipv6 form : xxxx.Xxxx.Xxxx.Xxxx.Xxxx no setting conditi...

  • Page 639: 90-57 : Backup Recovery Data

    Program 90 : maintenance program 90-57 : backup recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-57 : backup recovery data to backup the system data in the compact flash memory on the cpu and to make the...

  • Page 640: Description

    Program 90 : maintenance program 90-58 : restore recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-58 : restore recovery data to select the recovery data stored in the compact flash memory of the cpu. Aft...

  • Page 641: 90-59 : Delete Recovery Data

    Program 90 : maintenance program 90-59 : delete recovery data level: sa description note: this program is available only via telephone programming and not through pc programming. Use program 90-59 : delete recovery data to select and delete the recovery data stored in the compact flash memory of the...

  • Page 642: Description

    Program 90 : maintenance program 90-60 : t1/isdn layer status information level: in description use program 90-60 : t1/isdn layer status information to display layer status information for t1/pri/bri packages. Input data slot no. 00 ~ 16 (sl1000) 00 ~ 09 (sl1100) item no. Item input data default 01 ...

  • Page 643: 90-63 : Dr700 Control

    Program 90 : maintenance program 90-63 : dr700 control level: in description use program 90-63 : dr700 control to adjust settings of the dr700. Input data item no. Item input data default 01 priority timer 0 ~ 255 80 conditions none feature cross reference none issue 3.01 sl1000/sl1100 programming m...

  • Page 644: Description

    Program 90 : maintenance program 90-65 : 1st party cti authentication password setup level: sa description use program 90-65 : 1st party cti authentication password setup to set the authentication password. Input data item no. Item input data description default 01 password up to 16 characters sets ...

  • Page 645: Description

    Program 90 : maintenance program 90-66 : ftp firmware update setup level: in description use program 90-66 : ftp firmware update setup to setup the login info to connect to the ftp server. Input data item no. Item input data description default 01 user name up to 32 characters no setting 02 password...

  • Page 646: Description

    Program 90 : maintenance program 90-67 : backup data auto-save interval time set level: in description use program 90-67 : backup data auto-save interval time set to set time interval d-ram data that is saved in f-rom memory. D-ram memory : configuration information such as call transfer and do not ...

  • Page 647: 90-68 : Side Tone Auto Setup

    Program 90 : maintenance program 90-68 : side tone auto setup level: in description note: this program is available only via telephone programming and not through pc programming. Use program 90-68 : side tone auto setup to setup the volume level of side tone for each analog trunk port. This program ...

  • Page 648: Program 92 : Copy Program

    Program 92 : copy program 92-01 : copy program level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-01 : copy program to copy the data for one program to another multiline terminal, port, group, or other number. Refer to ...

  • Page 649

    Program no. Program name 22-02 incoming service type setup 22-03 trunk ring tone setup 22-05 irg assignment for normal ring trunk 22-08 second irg setup for unanswered dil / irg 31-05 incoming ring tone audible on external speaker 81–07 codec filter setup for analog trunk port trunk group base progr...

  • Page 650: Feature Cross Reference

    Department base program no. Program name 16-01 department (extension) group basic data setup copy all data except group name (item 01). 35-04 smdr port assignment for department group dss console base program no. Program name 30-01 dss console operation mode 30-03 dss key assignment door box base pr...

  • Page 651: Program 92 : Copy Program

    Program 92 : copy program 92-02 : delete all extension numbers level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-02 : delete all extension numbers to delete all extension numbers 11-02>, . However, the extension number...

  • Page 652: Program 92 : Copy Program

    Program 92 : copy program 92-03 : copy program by port number level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-03 : copy program by port number to copy extension and the data of each outside line. Input data program n...

  • Page 653: Program 92 : Copy Program

    Program 92 : copy program 92-04 : extension data swap level: in description note: this program is available only via telephone programming and not through pc programming. Use program 92-04 : extension data swap to swap data between two extensions. Input data item no. Item input data 01 1st extension...

  • Page 654: Feature Cross Reference

    Program number program name 21-10 dial block restriction class per extensions 21-11 hotline assignment 21-13 isdn calling party number setup for extension 21-15 individual trunk group routing for extensions 21-18 ip trunk (h.323) calling party number setup for extension 21-19 ip trunk (sip) calling ...

  • Page 655: Program 92 : Copy Program

    Program 92 : copy program 92-05 : extension data swap password level: in description use program 92-05 : extension data swap password to define the 4-digit password for each extension to allow extension data swap. Input data extension number up to four digits. (sl1000) up to eight digits. (sl1100) i...

  • Page 656: Program 92 : Copy Program

    Program 92 : copy program 92-06 : fill command level: in description use program 92-06 : fill command to allocate the data of each extension number of each extension group or each table. Input data program number xx - xx item no. Item input data 01 source number each extension port = 001 ~ 128 (sl10...

  • Page 657: Program 92 : Copy Program

    Program 92 : copy program 92-07 : delete command level: in description use program 92-07 : delete command to delete the data of each extension number of each extension group or each table. Input data program number xx-xx item no. Item input data 01 destination number (from) each extension port = 001...

  • Page 658: Description

    Program 93 : system information 93-01 : day/night mode information level: sa (this program is available for v3.0 or higher) description use program 93-01 : day/night mode information to display day/night mode for night mode service group. Input data night mode service group no. 1 ~ 4 item no. Item i...

  • Page 659: 93-02 : Trunk Information

    Program 93 : system information 93-02 : trunk information level: sa (this program is available for v3.0 or higher) description use program 93-02 : trunk information to display the setting of each trunk. Input data trunk port number 1 ~ 126 (sl1000) item no. Item input data description default relate...

  • Page 660: Description

    Program 93 : system information 93-03 : extension information level: sa (this program is available for v3.0 or higher) description use program 93-03 : extension information to display the settings of each extension. Input data extension up to 4 digits (sl1000) up to 8 digits (sl1100) item no. Item i...

  • Page 661: Feature Cross Reference

    Item no. Item input data description default related program 09 message waiting (rec) extension number (up to 4 digits) (sl1000) (up to 8 digits) (sl1100) read only: indicates extension number when left message waiting. None 11-11-09 11-11-10 11-11-11 10 alarm clock 1 0 = disable 1 = enable read onl...

  • Page 662: 93-04 : Redial List

    Program 93 : system information 93-04 : redial list level: sa (this program is available for v3.0 or higher) description use program 93-04 : redial list to display the redial list of each extension. Input data extension number up to 4 digits (sl1000) up to 8 digits (sl1100) redial last number 10 ite...

  • Page 663: Description

    Program 93 : system information 93-05 : department group information level: sa (this program is available for v3.0 or higher) description use program 93-05 : department group information to display the settings of each department group. Input data department group number 1 ~ 32 item no. Item input d...

  • Page 664

    Memo sl1000/sl1100 issue 3.01 2-642 program 93 : system information program 93.

  • Page 665

    Memo issue 3.01 sl1000/sl1100 programming manual 2-643.

  • Page 666: Programming Manual

    Programming manual nec corporation issue 3.01.