North Cool DI09SS1A User Manual - page 3
Instructions for Installation
Instructions to users
Please read the Instruction Manual carefully prior to the use of your heat pump so as to ensure proper operation.
Make sure you have the professional after-sale service persons of our company or the authorized
dealers install the units before you use it.
1. The units are not to be installed in places where
there might be a leak of flammable gases.
Leaked flammable gases accumulated around the units can
result in a fire hazard.
Make sure that the earth leakage-circuit
breaker is installed.
Absence of this breaker might lead to electric shock
and some other hazards.
After the connecting of the wires between the indoor unit and
the outdoor unit, check whether the connection is loose
or not by tugging the wire lightly.
A loose connection may result in a fire hazard.
Make sure that the heat pump is properly grounded.
The grounding wire on the heat pump
should be tightly connected to
the ground of the power source.
Improper grounding might cause
electric shocks or other hazards.
Instructions for Operation
Never try to stop the operation of the air conditioner
by operating the switch.
Such an act might cause electric shocks or fire hazards.
Do not press, stretch, damage, heat or modify
the power line.
This might cause electric shocks, overheating,
fire hazards, etc. If the power line wire is damaged
or needs to be replaced due to some other reasons
please make sure to have the dealer or the authorized
maintenance personnel do the replacement.
Do not operate the switch with wet hands.
This might cause electric shocks.
Never use the fuse with incorrect capacity or
any other metal wires.
The use of metal or copper wires for the fuse might cause
operational failures or fire hazards.
- 2 -
- 2 -
Copper
wire
Instructions d’installa
tion
Prière de lire les instructions soigneusement avant d’utiliser votre climatiseur
pour assurer qu’elle fonctionne proprement.
Les climatiseurs doivent être installés par un de nos techniciens professionnels ou
par une personne qualifiée.
1. N’installez pas l’appareil dans un endroit ou il
pourrait y avoir une fite de gaz combustible.
S’il y a une fuite de gaz qui s’accumule autour de l’appareil,
un accident ou un incendie peut se produire.
Assurez-vous que le disjoncteur de fuite de terre
est installé.
L’abscence du disjoncteur peut mener à une décharge électrique
ou autre risques.
Assurez-vous que la connection soit solide en tirant sur
le fil électrique avec un peu de force.
Une mise à terre malfaite peut causer un incendie.
Assurez-vous que la mise à la terre soit bien faite.
Le fil destiné à la mise à terre doit etre
connecté fermement à la d’électricité.
Sinon, il pose le risque de causer
des chocs électriques ou autredangers.
Instructions
d’opérations
N’essayez jamais d’arrêter le fonctionnement
du climatiseur en opérant l’interrupteur.
Une exécution pareille peut résulter d’un choc électrique
ou des risques d’incendie.
Évitez de presser, étirer
, endommager, chauf
fer
ou modifier le fil contenant le courant électrique.
Ceci peut mener à un choc électrique, surchauffage,
poser des risques d’incendie, etc. Si le fil électrique
est endommagé et doit être remplacé, engagez
un professionnel authorisé et qualifié pour faire
le remplacement nécessaire.
Ne touchez pas à l’interrupteur avec
des mains mouillées.
Ceci pourrait causer un choc électrique.
N’utilisez jamais le fusible avec un voltage incorrect
ou avec d’autre fils en metal.
L’utilisation d’un fil en cuivre ou d’un fil en métal pour le fusible
peut causer des pannes et risques d’incendie.
Fil de
cuivre