6 cu. Ft. Cement mixer owner’s manual warning: read carefully and understand all assembly and operation instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 998255.
Page of 14 2 thank you very much for choosing a northern industrial tools product! For future reference, please complete the owner’s record below: model: _______________ purchase date: _______________ save the receipt, warranty and these instructions. It is important that you read the entire manual ...
Page of 14 3 work area keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents. Do not use your tool where there is a risk of causing a fire or an explosion; e.G. In the presence of flammable liquids, gasses, or dust. Power tools create sparks, which may...
Page of 14 4 chart for minimum wire size of extension cord: nameplate amps cord length 25' 50' 100' 150' 0-6 18 awg 16 awg 16 awg 14 awg 6-10 18 awg 16 awg 14 awg 12 awg 10-12 16 awg 16 awg 14 awg 12 awg 12-16 14 awg 12 awg (not recommended) if in doubt, use larger cord. Be sure to check voltage req...
Page of 14 5 never start or stop the mixer with any material in the drum otherwise the motor will be damaged. Never use a mixer with a malfunctioning switch. Any mixer that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using. Di...
Page of 14 6 assembly (recommend that 2 people assist in assembly) 1. Place stand (#30) onto hinge bracket (#34) so that bolt holes line up as shown in figure a. 2. Insert hex bolts (#26) with washer (#27) through holes from one side, then washer (#27) lock nut (#23) from the other side, and tighten...
Page of 14 7 13. Move the connect seal from the inside to make sure the holes of drum upper, connector seal, drum lower align in a line, insert the bolt (#58) with washer (#57) through the holes and rotate them by hand. (figure f) note: make sure that eight screws be in place, and tighten with a wre...
Page of 14 8 17. Attach degree adjusting wheel (#20) to iron tube (#18) shaft as shown in figure k: a. Insert coil spring into the lower hole. B. While holding the spring in place, slide the wheel over the iron tube. Note: the m8*25 bolt (#69) usually have been secured in place, this step may need a...
Page of 14 9 19. Mounting the pulley and belt (figure n, o) a. Clean the shaft (#35) of all plastic protective material and other debris. Also clean out debris from drum pulley (#49) center hole. B. Position the drum pulley (#49) so that the set screw hole (#48) is facing outward. Squarely push the ...
Page of 14 10 d. Secure the motor, slide flat washers on four bolts (#41), then slide the bolts up through the bottom of the motor mount plate and the motor. Secure in place with locknut. E. Check if motor and belt turns true. Hands turn the drum pulley (#49) and verify that the motor pulley and dru...
Page of 14 11 maintenance warning: make sure this tool is turned off and disconnected from its power source before attempting any maintenance, cleaning, or inspection. It is recommended that the general condition of any tool be examined before it is used. Keep your tools in good repair by adopting a...
Page of 14 12 diagram.
Page of 14 13 parts list item# description qty item# description qty 1 bolt m10×25 4 40 motor mount plane 1 2 mixer blade 2 41 bolt m8×20 4 3 washer Φ10 9 42 motor 1 4 drum upper 1 43 motor base cover 1 5 lock nut m10 4 44 power cord 1 6 connector seal 1 45 switch 1 7 bolt m6×12 3 46 tap screw m5×10...
Page of 14 14 distributed by northern tool + equipment co., inc. Burnsville, minnesota 55306 northerntool.Com made in china warning: some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, ...
