Summary of Totally Wicked
Page 1
User manual.
Page 2
2 3 thank you for purchasing the odyssey™ thank you for purchasing your totally wicked odyssey™. The product has been both designed and manufactured in the united kingdom, to exacting standards and tolerances, to deliver what we believe to be one of the finest examples of a multi- purpose electronic...
Page 3
4 5 contents parts description 5 kit contents 6 about the guide 7 battery charging 7-11 introducing the odyssey™ tank 12 priming the cartomizer for the first time 13 assembly and operation of your odyssey™ 14 odyssey™ locking button 15 fitting the cartomizer into the fluid tank and preparing to fill...
Page 4
6 7 kit contents 1 x odyssey body. 1 x decorative plinth. 1 x stainless steel tank (3.48ml capacity). 1 x mouthpiece/drip-tip. 1 x filling device. 2 x 2.2ohm dedicated cartomizers. 1 x charger unit. 2 x 3.7v 900mah 14500 lithium ion protected circuit batteries. About the guide the following is a ste...
Page 5
8 9 battery charging uk / eu charging instructions • connect the charger lead to the charger socket and insert the plug into the power outlet socket. • switch on the power outlet. The charging led should be green - switch off the power supply. • batteries must be inserted into the charger in the cor...
Page 6
10 11 battery charging usa charging instructions • plug the charger into the power socket • switch on the power outlet. The charging led should be green - switch off the power supply. • batteries must be inserted into the charger in the correct orientation. Failure to fit batteries into the charger ...
Page 7
12 13 introducing the odyssey tank™ the odyssey tm tank body is precision machined from solid 303 stainless steel, and is lined with heat and impact resistant borosilicate glass to provide effective sight-glasses that show fluid level. The cartomizers supplied with the kit are unique to the odyssey™...
Page 8
14 15 assembly and operation of your odyssey™ • unscrew the top (3) and bottom (2) halves of the odyssey body. Insert a fully charged battery into the lower body with the positive (+) terminal towards the atomizer connector. • with the battery correctly inserted, screw the lower and upper battery bo...
Page 9
16 17 fitting the cartomizer into the fluid tank and preparing to fill carefully insert the cartomizer into the tank. The cartomizer should be inserted squarely into the tank, using a gentle twisting action to push the cartomizer smoothly through the o-rings. Take care not to insert the cartomizer o...
Page 10
18 19 when the tank is full, check the filler device has completely drained before sliding the tank body down the cartomizer to its bottom position. Remove the filling device by twisting it as you pull it up. Finally fit the mouthpiece. Without pressing the power button, take two short sharp draws o...
Page 11
20 21 operation with the odyssey™ now fully assembled and the operation of the locking and power switch understood, you are ready to go. Holding the device in either hand, we recommend holding the device in the manner shown below. The button is spring loaded so that only light pressure is required t...
Page 12
22 23 avoiding flooding and the “anti-flooding” tank position like any cartomizer system, the odyssey tank™ can suffer from flooding, where the central hole fills with fluid. This is most often caused by drawing too hard on the mouthpiece. A well-flooded cartomizer will need to be removed from the b...
Page 13
24 25 care and maintenance cleaning and general maintenance: keep the contacts and threads between the cartomizer/atomizer and the odyssey™ body clean. It is recommended that routine cleaning using a cotton bud, soaked in a degreasing agent as necessary, is used to prevent build-up of evaporated e-l...
Page 14
26 27 • keep the batteries away from children. • keep the battery contacts clean. • never leave batteries charging overnight or unattended. • if the battery is in any way damaged or leaking, dispose of and recycle it in an appropriate manner. • if the plastic insulation on the outside of the battery...
Page 15
28 29 problem symptom solution switch fails to connect. No vapour on switch activation. Clean brass screw head at base of battery compartment. Ensure battery contacts are clean. Stiff lock. Switch will not rotate to lock (or occasionally unlock). Occasionally this is due to ingress of dirt, but more...
Page 16
30 31 specifications battery: 14500 3.7v 900mah lithium ion protected battery, 14mm(d) x 50mm (l); weight 21g. Tank: 18.5mm(d) x 43.5mm(l), weight 21g. Odyssey™ body: 17.5mm(d) x 103.5mm(l), weight 68g. Plinth: 17mm(d) x 10.5mm(l), weight 6g. Mouthpiece/drip-tip: 9.5mm(d) x 25mm(l), weight 8g. Filli...
Page 17
32 33 it has been an ambition of totally wicked for a time to develop and produce its own unique products. We have always attempted to take a position of leadership in the early dawning years of electronic cigarettes. It was this company philosophy that has led to the development of the odyssey™. In...
Page 18
34 35 we had also recently procured our range of dual coil tanks and realised that not only did our customers seem to like them, they could also offer the atomizer and fluid delivery system concept to our new product. We would need to address a range of design issues that would be necessary to suppo...
Page 19
Manufactured in the uk for pillbox38 uk ltd, stancliffe street, blackburn, lancashire, bb2 2qr. Uk: tel 0845 602 9661 www.Totallywicked-eliquid.Co.Uk usa: tel 1(888) 761-9425 www.Totallywicked-eliquid.Com germany: tel 01803 942533 www.Totallywicked-eliquid.De.