Summary of H-430RX
Page 1
H-430 user manual issued: november2011 v1.0 website: http://www.Ojecoco.Com.
Page 2: Introduction
Page 2 of 15 introduction the h-430 is designed and manufactured by ojecoco photographic technology co., ltd, a specialist producer of photographic equipment and accessories. This wireless trigger set features separate transmitters and receivers. It is multi-functional, with wireless synchronized tr...
Page 3
Page 3 of 15 5. Follow safe operating procedures when using batteries, otherwise there may be a danger of overheating, explosion, fire, or risk to personal safety. 6. Do not use h-430 when you are near to locations with combustible substances or hazardous chemicals. 7. The h-430 is not water or mois...
Page 4: Preparation For Use
Page 4 of 15 h-430rx 1. Led status indicator light 2. 4 bit channel signal led 3. 3 bit group signal led 4. Test button 5. Hot shoe (flash only) 6. Channel setting button 7. 2.5mm shutter trigger socket 8. 2.5mm flash trigger socket 9. Group setting button 10. Power/flash/camera mode function switch...
Page 5: Specification
Page 5 of 15 specification radio frequency: 2.4ghz signal type: frequency shift keying (fsk) antenna: built-in pcb antenna control distance: 150m (subject to environmental limitations) channels: 5 flash groups: 3 groups; 7 different group combinations normal triggering sync-speed: 1/320 second batte...
Page 6
Page 6 of 15 8. In basic triggering mode: sync speed is up to 1/320s for mechanical shutter cameras, and in excess of this for hybrid electronic/mechanical shutter cameras (dependent on camera design). 9. H-430 is available in transmitter and receiver form factor and they are designed to be used tog...
Page 7
Page 7 of 15 setting channel, function mode and flash groups 1. Setting channels the h-430 can be set to one of 5 possible channels (“1”,“2”,“3”,“4”,“1234”). Ensure that you set all the transceivers to the same channel before use. One h-430tx can work with multiple h-430rxs to simultaneously control...
Page 8
Page 8 of 15 3. Setting flash groups when the h-430tx is in hold mode and the h-430rx is in camera mode, the group function does not work. With the h-430tx in camera mode, there are seven different combinations of groups that can be set. Press the group button (9) and the group leds show the current...
Page 9: Camera Shutter Triggering
Page 9 of 15 master camera to control multiple cameras place one h-430tx onto the master camera’s hot shoe, set the function switch to “camera - ”. With a h-430rx, set the function switch to “flash - ” and connect the shutter cable with “camera” interface of h-430rx to the shutter interface of the c...
Page 10
Page 10 of 15 2. Continuous shooting (set the camera to continuous shooting mode) almost the same as single shooting mode - but you need to keep pressing on the h-430tx trigger button for continuous shooting. 3. Bulb (set the camera to bulb or long exposure mode) again, almost the same as single sho...
Page 11
Page 11 of 15 wireless sync trigger 1．wireless trigger the h-430 can sync trigger off-camera flash, studio flash and camera flash. 2．when working a with h-550, the h-430 can remote control camera shooting and synchronize flash triggering to enable the camera work with several flashes at the same tim...
Page 12
Page 12 of 15 3．camera ttl flash and off-camera flash trigger the h-430tx supports on camera flash with ttl function and will not affect communication between camera and camera flash for ttl data. Meanwhile, it will also sync trigger off-camera flash (normal off-camera flash sync speed parameters ap...
Page 13
Page 13 of 15 other notes 1.1 wired trigger flash test. Set the function switch of h-430rx to “flash - ”, half press the trigger button, and it will trigger the connected flash. 1.2 wireless trigger flash test. Set the function switch of h-430tx to “camera - ”, half press the trigger button, and it ...
Page 14: Faq
Page 14 of 15 faq 1. General troubleshooting checklist make sure the battery is installed and receiver power switch turned on. Set the h-430tx and h-430rx to the same channel. Make sure the h-430tx and h-430rx are set to the correct function mode. Make sure the hot shoe mount is correctly connected....
Page 15
Page 15 of 15 cable options (extra cost) type 2.5mm to pc (screwlock) can be used for rx to flash pc sync port. All cables coiled; nominal length uncoiled is 1m. Shutter cable usage (camera model list may not be extensive): cable type usage c1 canon 60d, 1100d, 1000d, 600d, 550d, 500d, 450d, 400d, 3...