1. DL manuals
  2. Oki
  3. Printer
  4. MB461 MFP
  5. User Manual

Oki MB461 MFP User Manual

Summary of MB461 MFP

  • Page 1

    Basic user's manual this manual contains cautions on how to use this product safely. Before you use this product, please make sure that you read this manual. This manual supports the following models: mb461, mb471, mb491 es4161 mfp, es4191 mfp.

  • Page 2

    - 2 - p reface every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made...

  • Page 3: Eu/a

    - 3 - e mergency first aid take care with toner powder: if swallowed, give small amounts of cold water and seek medical attention. Do not attempt to induce vomiting. If inhaled, move the person to an open area for fresh air. Seek medical attention. If it gets into the eyes, flush with large amounts ...

  • Page 4: For Your Safety

    - 4 - z for your safety read the user's manual (this manual) for your safety before using the product. Cautions related to safety general cautions indicates additional information which, if ignored or failed to follow the guidelines, may result in personal fatal injury or death. Indicates additional...

  • Page 5

    - 5 - this product contains the software developed by heimdal project. Copyright (c) 1995 - 2008 kungliga tekniska högskolan (royal institute of technology, stockholm, sweden). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provide...

  • Page 6: Table of Contents

    - 6 - table of contents preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 emergency first aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 7

    Table of contents - 7 - settings for each dialing type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 setup of date/time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 specifying sender information . . . . ...

  • Page 8

    Table of contents - 8 - configuring fax settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 changing scan size (scan size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 changing resolution (resolution) . . . . . . . . . . . . . ....

  • Page 9

    Table of contents - 9 - setup to use the wsd scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 scanning methods . . . . . . . . . . . . . . . . . . . . . ...

  • Page 10

    Table of contents - 10 - 7 troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 paper jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 checking error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 11: Manual Composition

    - 11 - z manual composition the following manual is attached to this product. Z quick start guide quick start guide describes the initial setup to use each function. The basic operation of each function is also described. Z user's manual (basic) ---- this document in order to understand this machine...

  • Page 12: Legends Used In This Manual

    - 12 - legends used in this manual in this document, it may have written as follows. Z postscript3 emulation → pse, postscript3 emulation, postscript3 emulation z microsoft ® windows ® 7 64-bit edition operating system→ windows 7 (64bit version) z microsoft ® windows vista ® 64-bit edition operating...

  • Page 13: 1. Setup

    - 13 - setup 1 1. Setup in this chapter, the basic operations of this machine and the setup are described before using each function. Z overview of machine this section describes the overview of the machine. Contents of the package check that you have everything shown below. Reference z for details ...

  • Page 14: Available Options

    Overview of machine - 14 - available options the following options are available for your machine: z second tray unit (tray 2) reference z for details on how to install the options, refer to "installing options" p. 22 . Installation requirements installation environment your machine must be installe...

  • Page 15: Names Of Components

    Overview of machine - 15 - setup 1 installation space install your machine on a flat surface that is wide enough to locate the machine. Allow for enough room around your machine according to the images below. Z top view z side view z side view (tray 2 installed) names of components 20cm (193cm) 20cm...

  • Page 16

    Overview of machine - 16 - z internal part of the connector cover no. Name 13 fuser unit 14 starter toner cartridge 15 image drum 16 led head 17 power switch no. Name 18 faceup stacker 19 ac power socket 20 air vents 21 line connection 22 tel connection 16 13 15 17 14 line tel 22 21 18 19 20 no. Nam...

  • Page 17: Installing Your Machine

    Installing your machine - 17 - setup 1 z installing your machine this section explains how to unpack your machine and how to turn it on and off. Unpacking your machine note z the image drum (the green tube) is very delicate. Handle it carefully. Z do not expose the image drum to direct sunlight or v...

  • Page 18

    Installing your machine - 18 - 7 open the document glass cover. 8 remove the protection tapes (6). Open the adf and remove packing tapes. 9 close the document glass cover. Now, you can open or close the scanner. 10 open the scanner unit. 11 remove the protection tapes, and remove desiccants and film...

  • Page 19

    Installing your machine - 19 - setup 1 15 reinstall the image drum in the printer:lower it into place in the printer locating the pegs (1) at each end into their slots in the sides of the printer cavity (2). 16 turn the lever in the direction shown. Z the arrow on the lever should align with the arr...

  • Page 20

    Installing your machine - 20 - turning on your machine 1 plug the ac cable into the ac power socket of your machine. 2 plug the ac cable into the electric socket. 3 check that no documents are on the document glass or adf, and the adf cover is closed. 4 hold down the power switch for about a second ...

  • Page 21

    Installing your machine - 21 - setup 1 the power save > key lights up while in the mode. Memo z by factory default, the time interval to enter the power saving mode is set to 30 minutes. You can change the time interval by pressing the setting> key on the operator panel and selecting [admin setup] >...

  • Page 22: Installing Options

    Installing options - 22 - z installing options this section explains how to install options on your machine. The following options are available: z second tray unit note z be sure to hold down the power switch for about a second to turn off the power and unplug the ac cable and ethernet or usb cable...

  • Page 23

    Installing options - 23 - setup 1 printer driver configuration note z you must be logged in as an administrator to complete this procedure. Z if the following conditions are met for mac os x, it is not necessary to configure the printer driver, as the configured option information is automatically t...

  • Page 24

    Installing options - 24 - 5 if the optional tray is already mounted, click [second tray], and then click [ok]. „ for mac os x pcl/ps driver (mac os x 10.4.0 to 10.4.11) memo z the following procedure uses mac os x 10.4.11 as an example. Depending on an os, the description may be different. 1 from [g...

  • Page 25: Operator Panel

    Operator panel - 25 - setup 1 z operator panel this section explains the names and functions of components on the operator panel and how to enter text. No. Name function 1 display screen displays operating instructions and the status of the machine. 2 main function keys switches functions. The selec...

  • Page 26: Default Screen

    Operator panel - 26 - default screen turn the power on, and when the machine is in the state in which it can be used, the copy start screen will be displayed as the default mode. You can switch to other functions by using the main function keys. Reference z you can change the default screen by press...

  • Page 27

    Operator panel - 27 - setup 1 entering text 1 press , , , to select the character you want, and then press . The selected character is entered in the text field. 2 repeat step 1 until all the characters required are entered. 3 press the and to select [enter] and press to complete the entry process. ...

  • Page 28

    Operator panel - 28 - „ using qwerty keyboard (mb471, mb491, es4191 mfp) you can also use the qwerty keyboard to enter alphanumeric characters and symbols in the entry screen. The keyboard enables you to switch the entry mode to the standard mode, caps mode, or ctrl mode. The changed mode is reflect...

  • Page 29: Loading Paper and Documents

    Loading paper and documents - 29 - setup 1 z loading paper and documents this section explains the specifications for paper and document, and how to load them. Paper supported paper types for high-quality printing and to avoid printing problems, be sure to use the supported paper types. Please use d...

  • Page 30

    Loading paper and documents - 30 - paper type paper size mm (inch) paper weight envelope monarch 98.4 x 190.5 (3.875 x 7.5) envelopes should be 88 g/m 2 (24lb) paper, and flap parts of envelopes should be folded com-9 98.4 x 225.4 (3.875 x 8.875) com-10 104.8 x 241.3 (4.125 x 9.5) dl 110 x 220 (4.33...

  • Page 31

    Loading paper and documents - 31 - setup 1 paper recommendations your mfp will handle a variety of print media, including a range of paper weights and sizes. This section provides general advice on choice of media, and explains how to use each type. The best performance will be obtained when using s...

  • Page 32

    Loading paper and documents - 32 - loading paper your machine has two built-in trays (tray 1 and the mp tray) (mb461 is manual feeder.) and an optional tray (tray 2).Refer to the list below to check the supported paper and capacities of each tray. Note z duplex printing can not be performed on paper...

  • Page 33

    Loading paper and documents - 33 - setup 1 „ loading paper in tray 1 and tray 2 the following procedure explains how to load paper in tray 1 or tray 2 (optional). Memo z the following procedure uses tray 1 as an example but the same is applied to tray 2. 1 pull out the paper tray. 2 slide the paper ...

  • Page 34

    Loading paper and documents - 34 - 4 flex paper back and forth, and then fan it. Straighten the edges of the paper stack on a level surface. 5 load paper with the print side face down. Note z do not load paper above the fill line (3). 6 push the paper tray until it stops. Register the loaded paper o...

  • Page 35

    Loading paper and documents - 35 - setup 1 5 insert the paper with the print side face up until its edge touches the paper feed entrance. Note z do not load paper above the fill line (1). 6 press the set button (2). Register the loaded paper on your machine. Proceed to "configuring the tray settings...

  • Page 36

    Loading paper and documents - 36 - „ configuring the tray settings after you load paper in tray 1, tray 2 (optional), or the mp tray, you need to register the loaded paper on your machine. 1 press the setting> key on the operator panel. 2 press the to select [paper setup] and then press . 3 press th...

  • Page 37: Documents

    Loading paper and documents - 37 - setup 1 paper output your machine outputs to the facedown or faceup stacker. Paper types that can be outputted to each stacker are as follows. When performing duplex printing, paper outputs to the facedown stacker. Note z do not open or close the faceup stacker whi...

  • Page 38

    Loading paper and documents - 38 - scannable area the text or images on the shaded area shown below are not scanned. Memo z the arrow in the above drawing indicates the feeding direction in the auto document feeder, or the scanning start side on the document glass. Loading documents note z for docum...

  • Page 39

    Loading paper and documents - 39 - setup 1 if your document is landscape, align its right edge to the upper-left corner of the glass. 3 close the document glass cover gently. Reference z [document direction] setting according to the direction of your document to get the output you want. The factory ...

  • Page 40: Es4191 Mfp Only)

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 40 - z basic settings for faxing (for mb471, mb491, es4191 mfp only) this section explains basic settings for faxing. Be sure to configure the following settings before you transmit faxes. Setting for country code note z please select t...

  • Page 41: Connecting A Telephone Line

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 41 - setup 1 connecting a telephone line depending on your environment, a method to connect a telephone line is different. Based on the following figures, connect the line for your environment. Note z turn off the machine when you conne...

  • Page 42: Other Cases

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 42 - - when you send fax or receive, the fax picture may be broken or communication error may occur by picking up the telephone. - the fax transfer function is not able to work from the external telephone. Memo z in the case of direct i...

  • Page 43

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 43 - setup 1 connecting pbx, home telephone or business phone plug the [telephone cable] connected to the [public line (analog)] into the [line connection] of your machine. Remove the telephone connector cover. Plug the telephone cable ...

  • Page 44: Setup Of Date/time

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 44 - 7 press , select dial type, and then press . 8 press the until the top screen is displayed. Setup of date/time setup of date/time of your region. Reference z you can set up date and time automatically using webpage. For details, re...

  • Page 45: Pbx Connecting

    Basic settings for faxing (for mb471, mb491, es4191 mfp only) - 45 - setup 1 12 when the setup menu screen is displayed, press to complete the setup. Pbx connecting when connecting to pbx (internal exchange), put [pbx line] to [on]. 1 press the setting> key. 2 press the to select [admin setup] and t...

  • Page 46: Connecting to A Computer

    Connecting to a computer - 46 - z connecting to a computer this section explains how to connect your machine to a computer and install a printer and fax driver. „ connecting method you can select either of the following connection methods: z "network connection" p. 47 z "usb connection" p. 55 „ prod...

  • Page 47: Network Connection

    Connecting to a computer - 47 - setup 1 network connection do the following procedure to connect your machine to a computer via network. Connecting an ethernet cable be sure to connect your machine to a network with an ethernet cable before driver installation. 1 prepare an ethernet cable and a hub....

  • Page 48

    Connecting to a computer - 48 - 4 enter the administrator password. The factory default password is "aaaaaa". 5 select [complete], and press . 6 press the and [network setting], and then press the . 7 if setting the ip address manually, check that [manual] is selected, and press . If obtaining the i...

  • Page 49

    Connecting to a computer - 49 - setup 1 7 select the checkbox of the printer driver, fax driver or both you want to install, and click the install bunch button. Memo z by factory default, [pcl driver], [scanner driver], and [actkey] are selected. Z all of drivers and software packages are installed ...

  • Page 50

    Connecting to a computer - 50 - installing a printer driver (for mac os x) to complete the network connection with a mac operating system, install a printer driver on the computer and set your machine as a network printer. Select the protocol for your network connection from the following: z etherta...

  • Page 51

    Connecting to a computer - 51 - setup 1 9 select the name of your machine and then check that [oki mb491(ps)] is displayed in [print using]. 10 click [add]. 11 check that your machine is displayed in [printers] and [oki mb491(ps)] is displayed in [kind]. Note z if [oki mb491(ps)] is not correctly di...

  • Page 52

    Connecting to a computer - 52 - 3 select [network port configurations] from [show], and then check that [built-in ethernet] is selected. 4 select [built-in ethernet] from [show] and select the [appletalk] tab, and then check that [make appletalk active] is selected. 5 close [network]. 6 insert "soft...

  • Page 53

    Connecting to a computer - 53 - setup 1 19 click [ok]. 20 remove "software dvd-rom" from the computer. The installation is complete. „ using bonjour (for mac os x 10.5 to 10.7) then, install the driver in the computer and set the machine as a network printer. ‰install the driver in the computer. 1 e...

  • Page 54

    Connecting to a computer - 54 - note z if [oki mb491(ps)] or [oki mb491(pcl)] is not correctly displayed in [kind], click [-] to remove your machine from [print & fax] and then redo the procedure from step 8 to 12. 14 close [print & scan] (for mac os x 10.5 and 10.6:[print & fax]). 15 remove "softwa...

  • Page 55: Usb Connection

    Connecting to a computer - 55 - setup 1 15 check that the name of your machine is displayed in [printer list], and then close the window. 16 from the [go] menu, select [applications] > [textedit]. 17 select the [file] menu > [page setup]. 18 select the name of your machine from [format for]. 19 chec...

  • Page 56

    Connecting to a computer - 56 - installing a printer and fax driver (for windows) note z you must be logged in as an administrator to complete this procedure. 1 ensure that your machine is turned off and the usb cable is unplugged from the computer. 2 turn on the computer. 3 insert "software dvd-rom...

  • Page 57

    Connecting to a computer - 57 - setup 1 12 click the [exit] button. 13 remove "software dvd-rom" from the computer. The installation is complete. ‹ print a test page to check that the printer driver is successfully installed on the computer. 1 click [start] > [devices and printers]. 2 right-click th...

  • Page 58

    Connecting to a computer - 58 - 12 close [print & scan](mac os x 10.5 and 10.6:[print & fax]). 13 remove "software dvd-rom" from the computer. The installation is complete. „ for mac os x 10.4.0 to 10.4.11 memo z the procedure below uses mac os x 10.4.11 as an example. Depending on your os, the desc...

  • Page 59

    Configuring the network settings - 59 - setup 1 z configuring the network settings this section describes the setup required for using scan to e-mail, scan to network pc, scan to fax server, internet fax functions. The above functions enable you to send scanned data to a computer via the network con...

  • Page 60: Checking The Common Setup

    Configuring the network settings - 60 - checking the common setup information check the common setup information for scan to e-mail, scan to network pc, scan to fax server and internet fax, and fill in the corresponding columns of the setup information form. „ administrator password for your machine...

  • Page 61

    Configuring the network settings - 61 - setup 1 4 on the [general] tab, enter the contents of [name] and [e-mail address] in b-9 and b-10 of the setup information form. 5 click the [servers] tab, and then note each setting in the corresponding columns of the setup information form. - if there is a c...

  • Page 62: Setting Up Scan to Network

    Configuring the network settings - 62 - 7 select [enter] and then press . 8 press the and then enter the information in b-1. 9 select [enter] and then press . 10 press the and then select a protocol for receiving e-mail for the machine, and then press . - if you want your machine to receive e-mail f...

  • Page 63

    Configuring the network settings - 63 - setup 1 3 select [see the name of this computer] under [system]. 4 enter the name in [computer name] in c-1 of the setup information form. 5 close the window. „ for windows server 2003 and windows xp 1 click [start] > [control panel] > [performance and mainten...

  • Page 64

    Configuring the network settings - 64 - 4 enter the information in c-2 in the text box. 5 ensure that [standard user] is selected, and then click [create account]. 6 click the icon of the user account created in step 5. 7 select [create a password]. 8 enter the information in c-3 in [new password] a...

  • Page 65

    Configuring the network settings - 65 - setup 1 18 click [add]. 19 enter the value in c-2 in the entry field and then click [ok]. 20 select the user added in step 13 and select the [allow] check box for [full control], and then click [ok]. 21 click [ok]. 22 click [close]. Proceed to "creating a prof...

  • Page 66

    Configuring the network settings - 66 - 12 click [if you understand the security risks but want to share files without running the wizard, click here.]. If the screen below appears, select [share this folder] and click [permissions]. Proceed to step 15. 13 select [just enable file sharing] in window...

  • Page 67

    Configuring the network settings - 67 - setup 1 „ for windows server 2003 memo z the items here may differ depending on the edition you are using. 1 click [start] > [administrative tools] > [computer management]. 2 in the right window, double-click [system tools] > [local users and groups], and then...

  • Page 68

    Configuring the network settings - 68 - „ for mac os x 10.5 to 10.7 1 from the apple menu, select [system preferences]. 2 click [users & groups] (for mac os x 10.5 and 10.6: [accounts]). 3 click [click the lock to make changes.] at the bottom left of the screen and enter the administrator's password...

  • Page 69

    Configuring the network settings - 69 - setup 1 17 select the account created in the step 8 and click [select]. 18 click the triangle button at the right side of the user added in the step 17 and select [read & write]. 19 click [options]. 20 check the checkbox of [share files and folders using smb (...

  • Page 70

    Configuring the network settings - 70 - 8 check that an account is added to [other accounts] with the name of c-2, and close [accounts]. 9 create a new folder on the computer with the name entered in c-5. 10 from the apple menu, select [system preferences]. 11 click [sharing]. 12 check the checkbox ...

  • Page 71: Managing Profiles

    Configuring the network settings - 71 - setup 1 12 enter the information in c-2. Note z if domain management is done, enter "c-2@domain name". Z when carrying out domain management, if you cannot connect even after entering "c-2@domainname", delete "@domainname". Access the machine's website again, ...

  • Page 72: Printing Configuration

    Printing configuration - 72 - z printing configuration this section explains how to print the configuration on which you can check the detailed information of your machine, such as the settings and status of your machine. Printing procedure 1 press the setting> key on the operator panel. 2 press the...

  • Page 73: 2. Copying

    - 73 - copying 2 2. Copying this chapter explains the basic operation and settings for your machine's copy function. Z basic operation this section explains how to start and cancel copy job. Starting a copy job 1 press the copy> key on the operator panel to open the copy standby screen. 2 place your...

  • Page 74: Configuring Copy Settings

    Configuring copy settings - 74 - z configuring copy settings you can change the copy settings to alter the output to suit your needs. Each setting can be configured from the [change settings] menu on the copy standby screen. Perform the following procedures at step 3 of "starting a copy job" p. 73 d...

  • Page 75: Changing Image Orientation

    Configuring copy settings - 75 - copying 2 4 when the pop-up message is displayed, press the or to select [start] and then press . Reference z for details on how to load the paper on the mp tray, refer to "loading paper on the mp tray (mb471/mb491/es4191 mfp)" p. 34 . Changing image orientation of d...

  • Page 76: (Continuous Scan)

    Configuring copy settings - 76 - 4 press the until the start screen is displayed. Note z when [paper feed] is set to [auto], some values cannot be selected. The selectable values differ according to the selected scan size. Z with some ratios, parts of the document's image may be missing or margins m...

  • Page 77: Making Duplex Copies (Duplex

    Configuring copy settings - 77 - copying 2 making duplex copies (duplex copy) you can copy 1-sided (simplex) and 2-sided (duplex) documents on to one side (simplex) or both sides (duplex) of a sheet of paper. You can also select the binding position from either long- edge or short-edge binding. Spec...

  • Page 78: Adjusting The Background

    Configuring copy settings - 78 - 2 press the to select [image settings] and then press . 3 press the to select [document type] and then press . 4 press the to select a document type and then press . Memo z [text]: set when copying a text document. Z [text&photo]: set when copying a document having t...

  • Page 79: Resetting Copy Settings

    Configuring copy settings - 79 - copying 2 resetting copy settings auto reset all settings you configured for your copy job return to their default values if no operation is made for a set period of time. The auto reset time is set to 3 minutes as the factory default setting. Reference z you can cha...

  • Page 80: Mfp Only)

    - 80 - 3. Faxing (for mb471, mb491, es4191 mfp only) this chapter explains basic settings and operations for faxing, scanning to fax server and internet faxing and operations on managing the phone book. Z basic procedure for faxing this section explains basic operations for transmitting faxes. You n...

  • Page 81: Specifying A Destination

    Basic procedure for faxing - 81 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 specifying a destination you can specify a destination in the following six ways: z using the ten-key pad z using a speed dial z using a group z using the transmission histories z using the reception histories z using ...

  • Page 82

    Basic procedure for faxing - 82 - using transmission and reception history you can select a destination from the 50 most recent transmissions or receptions. 1 press the to select [tx history] or [rx history] and then press . 2 press the to select an entry and then press . The check box is selected. ...

  • Page 83: Configuring Fax Settings

    Configuring fax settings - 83 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 z configuring fax settings you can configure the fax settings to alter the output to suit your needs. Each setting can be configured from the [fax functions] menu on the fax start screen. Perform the following procedures...

  • Page 84: Canceling Fax Transmission

    Checking and canceling fax transmission - 84 - z checking and canceling fax transmission this section explains how to check or cancel fax jobs. Canceling fax transmission you can cancel a job that is being transmitted as long as the message indicating the job has been completed has not appeared. 1 p...

  • Page 85: Reception Behavior

    Machine behavior in fax reception - 85 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 z machine behavior in fax reception this section explains how your machine behaves when receiving and printing faxes. Reception behavior the machine behavior differs depending on the specified reception mode. Yo...

  • Page 86

    Machine behavior in fax reception - 86 - when using two numbers with distinct rings(drd) this mode is programmed for the fax to answer only on a distinctive ring. You can have a signal phone line to have two numbers with distinct rings, one for regular phone calls and one for fax. If the phone line ...

  • Page 87: Printing Received Faxes

    Machine behavior in fax reception - 87 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 printing received faxes the machine automatically prints out the received fax. You can specify the paper tray to use. Note z do not pull out the paper trays when the machine is printing. Memo z use only standard...

  • Page 88: Phone Book

    Phone book - 88 - z phone book this section explains how to register fax numbers in the phone book, and how to edit or delete registered numbers. In the phone book, you can set frequently used numbers to speed dial and also create groups of numbers to which you can broadcast faxes. Speed dial you ca...

  • Page 89: Group Dial (Group Number)

    Phone book - 89 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 8 repeat steps 4 to 11 in "registering and editing" p. 88 . The fax number is automatically entered. You do not have to enter it manually. Deleting 1 press the setting> key on the operator panel. 2 press the to select [phone book] and...

  • Page 90: One-Touch Key Pad

    Phone book - 90 - 5 press the to select [delete] and then press . 6 press the or to select [yes] and then press . Memo z you cannot delete an entry which is specified as a reserved fax job or for the auto deliver function. One-touch key pad the speed dials no.1 to 16 are automatically registered to ...

  • Page 91: Specifying The Destination

    Basic procedure for scan to fax server - 91 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 z basic procedure for scan to fax server this section explains basic operations for data transmission to the fax server. The faxserver function allows you to transmit fax data as a file attached to an e-mai...

  • Page 92

    Basic procedure for scan to fax server - 92 - the box is checked. You can select multiple entries. 3 when you have selected all the destinations, press the . 4 check that [complete] is selected, and then press . Direct input this is the same as the fax function. Using the tx history you can select a...

  • Page 93: Sending An Internet Fax

    Basic procedure for internet faxing - 93 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 z basic procedure for internet faxing this section explains basic operations for transmitting internet faxes. The internet fax function allows you to transmit fax data as a file attached to an e-mail. A docume...

  • Page 94: Specifying A Destination

    Basic procedure for internet faxing - 94 - specifying a destination you can specify a destination in the following five ways: z using the address book z using a group z using the transmission histories z direct input z using ldap search perform one of the following procedures at step 7 of "sending a...

  • Page 95: Checking, Deleting, and

    Basic procedure for internet faxing - 95 - fa xing (for mb471, mb491, es 4191 mfp onl y) 3 using ldap search you can search for a destination that is on the ldap server. You can select either [simple search] or [advanced search] for the method of searching. [simple search] only searches for a single...

  • Page 96: Canceling Transmission

    Basic procedure for internet faxing - 96 - 4 check that [close the list] is selected and then press . Deleting a destination 1 press the on the start screen to select the specified destination and then press . 2 press the to select the destination type in which the destination you want to delete is ...

  • Page 97: 4. Scanning

    - 97 - scan ning 4 4. Scanning this chapter explains the basic operation and settings for your machine's scanning functions. Z installing scanner drivers (twain/wia/ica driver) this section explains the procedure to install the scanner driver. Before using scan function, install the scanner driver. ...

  • Page 98

    Installing scanner drivers (twain/wia/ica driver) - 98 - 8 check the checkbox of [network scanner] and click [next]. 9 select [ip address] or [search mfp] check box to enter the address of the machine and then click [next]. If you want to set the [ip address], follow procedure 10. 10 if [search mfp]...

  • Page 99

    Installing scanner drivers (twain/wia/ica driver) - 99 - scan ning 4 4 click [continue]. 5 click [continue]. 6 check the display and click [continue] if ok. 7 read the license agreement and click [continue]. 8 click [agree] if you agree. 9 click [install]. To change the installation location of the ...

  • Page 100: Using Actkey Software

    Installing scanner drivers (twain/wia/ica driver) - 100 - using actkey software using the actkey, you can start a scan job in specified settings with a click a button. Memo z actkey does not support mac os x. Z using wsd scanning, actkey does not work. Z when actkey is installed, network configurati...

  • Page 101: Setup to Use The Wsd Scan

    Setup to use the wsd scan - 101 - scan ning 4 z setup to use the wsd scan the following explains how to set up the pc to use the wsd scan function. In order to use the wds scan function, install this device on the pc. Wsd scan can be used from scan to local pc and scan to remote pc via network. To u...

  • Page 102: Scanning Methods

    Scanning methods - 102 - z scanning methods this section explains the basic operation of the scan function. In scan mode, you can use five scan functions, scan to e-mail, scan to usb memory, scan to network computer, scan to local computer and pc scan. You can select these functions after pressing s...

  • Page 103

    Scanning methods - 103 - scan ning 4 3 when you have selected all the destinations, press the . 4 check that [complete] is selected and then press . 5 press the to return to start screen. „ direct input you can enter a destination directly using the onscreen keyboard. 1 press the to select [direct i...

  • Page 104: Scan To Network Pc

    Scanning methods - 104 - scan to network pc you can send a scanned document to a server on the network. The document is scanned and converted to a pdf, jpeg, tiff, or xps file. The factory default setting is pdf. Note z check that the machine is connected to the network. Z it is necessary to set up ...

  • Page 105: Scan to Local Pc

    Scanning methods - 105 - scan ning 4 scan to local pc you can save the scanned data into your local computer. When you press the or , the scan job starts and the actkey utility and the twain driver start automatically. You can send the scanned document to a specified application, save it in a specif...

  • Page 106: Scan to Remote Pc

    Scanning methods - 106 - 7 press the to select [select an application] and then press . 8 press the to select where to send the scanned document and then press . 9 press or . Memo z if you select [application], the specified application starts and the scanned image is displayed on the application. Z...

  • Page 107

    Scanning methods - 107 - scan ning 4 simple scan mode „ for windows 1 press the scan> key on the operator panel. 2 place your document with text face up in the adf or face down on the document glass. 3 press the to select [remote pc] and then press . 4 check that the [twain] is selected, and press ....

  • Page 108

    Scanning methods - 108 - „ for mac os x 1 press the scan> key on the operator panel. 2 place your document with text face up in the adf or face down on the document glass. 3 press the to select [remote pc] and the press . 4 check that the [twain] is selected, and press . 5 check that [select a conne...

  • Page 109

    Scanning methods - 109 - scan ning 4 10 click a scan button. Scanning starts. 11 select [quit photoshop] from [photoshop]. Wsd scan (for network connection) „ for windows 1 press the scan> key on the operation panel. 2 place the original on the automatic document feeder or on the scanner glass. 3 pr...

  • Page 110: Registering Address Book

    Registering address book - 110 - z registering address book this section explains how to register and deleted the address book and group list. You can register e-mails to the address book and create groups for broadcasting messages. The address book and the group list can be used to specify the dest...

  • Page 111: Group List

    Registering address book - 111 - scan ning 4 group list you can create up to 20 groups of e-mail addresses. Registering and editing reference z for details on how to enter text, refer to "entering text using the operator panel" p. 26 . 1 press the setting> key. 2 press the to select [address book] a...

  • Page 112: Registering and Editing

    Registering network scan destinations - 112 - z registering network scan destinations this section explains how to register a pc connected to the network. You can register locations on a network to which you can scan documents. Memo z you can also register network-connected pcs with actkey in networ...

  • Page 113: 5. Using As A Printer

    - 113 - using as a pr in ter 5 5. Using as a printer this chapter describes how to print documents from a computer or usb memory. Z printing from a computer this section explains how to print from a computer. Memo z this section uses wordpad in windows and textedit in mac os x as examples. The displ...

  • Page 114

    Printing from a computer - 114 - 4 select the [paper/quality] tab. 5 select a tray from [paper source]. 6 click [advanced]. 7 click [paper size] and select a paper size from the drop-down list. 8 click [media type] and select the media type from the drop-down list. 9 click [ok]. 10 click [ok]. 11 cl...

  • Page 115: Canceling A Print Job

    Printing from a computer - 115 - using as a pr in ter 5 10 click [print]. For mac os x pcl printer driver 1 from the [file] menu, select [page setup]. 2 select the printer you want to use from [format for]. 3 select a paper size from [paper size] and then click [ok]. 4 from the [file] menu, select [...

  • Page 116: Printing From Usb Memory

    Printing from usb memory - 116 - z printing from usb memory this section explains how to print from the usb memory. Inserting the usb memory into the machine, you can print the document stored in it directly. Note z not all usb memory products are guaranteed to work. (usb memory with security functi...

  • Page 117: Configuring Print Settings

    Printing from usb memory - 117 - using as a pr in ter 5 11 remove the usb memory from the port after a message is displayed indicating that it is ok to remove the usb memory. Configuring print settings you can configure the settings for printing from usb memory on the [print setup] menu. Perform the...

  • Page 118: Canceling A Print Job

    Printing from usb memory - 118 - 2 press the to select [fit] and then press . 3 press the to select [on] for matching the paper size or [off] for not resizing the page size and then press . 4 press the to return to the start screen. Canceling a print job you can cancel a print job from the usb memor...

  • Page 119: Control

    - 119 - user a u th ent icat ion and access control 6 6. User authentication and access control this chapter explains the user authentication and access control functions. Z about user authentication and access control the user authentication and access control functions allow you to limit the funct...

  • Page 120: Authentication By Pin

    Authentication by pin - 120 - z authentication by pin this section explains how to enable the access control using the authentication by pin and how to operate when the access control is enabled. Registering a pin before enabling the user authentication and access control, be sure to register a pin ...

  • Page 121

    Authentication by pin - 121 - user a u th ent icat ion and access control 6 3 press the or on the confirmation screen to select [yes] and then press . Memo z after a certain period of time, the machine automatically logs out users. Operation from a computer to control access to operations from a com...

  • Page 122

    Authentication by pin - 122 - 9 click [save]. 10 if a message is displayed asking you to input the user password, enter the password and click [ok]. 11 open the file to print. 12 select [print] from the [file] menu. 13 select your machine and click [print]. „ printing (for max os x pcl driver) 1 fro...

  • Page 123: Registering User Name and

    Authentication by user name and password - 123 - user a u th ent icat ion and access control 6 z authentication by user name and password this section explains how to enable the access control using the authentication by the user name and password and how to operate when the access control is enable...

  • Page 124

    Authentication by user name and password - 124 - 3 press the or on the confirmation screen to select [yes] and then press . Memo z after a certain period of time, the machine automatically logs out users. Operation from the computer memo z the authentication type specified on the computer overrides ...

  • Page 125

    Authentication by user name and password - 125 - user a u th ent icat ion and access control 6 „ faxing from a computer (for windows only) memo z this procedure uses notepad as an example. The procedures and menus may differ depending on the os you use. 1 open the file you want to fax. 2 from the [f...

  • Page 126: 7. Troubleshooting

    - 126 - 7. Troubleshooting this chapter provides solutions to the problems you may encounter while operating your machine. Z paper jams this section explains how to clear paper jams. Reference z for details on the location of each component of the machine, refer to "cleaning your machine" on p. 165 ...

  • Page 127

    Paper jams - 127 - tr oubleshooting 7 4 carefully lift out the image drum, complete with the toner cartridge. Be careful not to touch or scratch the green drum surface. 5 remove the image drum as described in step 3, then, remove the duplex unit (1) by raising the coloured handles (2) on each side, ...

  • Page 128

    Paper jams - 128 - error code 380, 381, 382, 389 (paper feed jam) 1 remove any documents from the document tray if any. 2 open the scanner unit. 3 press the top cover open button (1) and open the top cover. 4 carefully lift out the image drum, complete with the toner cartridge. Be careful not to tou...

  • Page 129

    Paper jams - 129 - tr oubleshooting 7 and pull out the paper carefully. If you cannot remove the paper by following steps (a)1 and (a)2, pull out the paper by following steps (b). • if you have failed to remove jammed paper, do not force to pull out the paper but follow the steps below. Return the i...

  • Page 130

    Paper jams - 130 - if neither the top or bottom end of paper is visible, move the jammed paper in the arrow direction as shown. Hold the top end of paper by your hands and carefully pull out the paper. If the bottom end of paper is visible, hold the paper by your hands and carefully pull out the pap...

  • Page 131

    Paper jams - 131 - tr oubleshooting 7 document jam occurred „ when you can see the document in the duplex paper path 1 open the adf cover, and pull out the document upward. „ when you can see the document inside the adf 1 remove any documents from the document tray if any. 2 open the adf cover. 3 ho...

  • Page 132: Error Messages

    Error messages - 132 - z error messages this section explains the causes and remedies for the error messages displayed on the display screen and the function of the status> key. Error messages displayed on the screen memo z in the following lists: - "%color%" indicates k (black) - "%tray%" indicates...

  • Page 133

    Error messages - 133 - tr oubleshooting 7 613 %color% toner cartridge not installed. : %errcode% please see help for details. Blinks the toner cartridge of the indicated color is not properly installed. Reinstall it properly. 613 : k %color% toner cartridge not installed. Please see help for details...

  • Page 134

    Error messages - 134 - disk use failed %fs_err% please see help for details. To close blinks a disk operation error occurred. Please check data. Message data write error : %code%. Lights up failed to write message data to be uploaded. Contact your dealer. Please check %color% toner cartridge. Please...

  • Page 135

    Error messages - 135 - tr oubleshooting 7 power off/on %errcode%: error %fatalstring1% blinks an error occurred in the device. Turn the machine off and then on again. If the same error occurs, turn the machine off and then on again. If the error is not resolved, or the same error occurs again, conta...

  • Page 136

    Error messages - 136 - error messages for copying the following messages are displayed on the display screen of the operator panel while using the copy function. Error messages for faxing the following messages are displayed on the display screen of the operator panel while using the fax function. 4...

  • Page 137

    Error messages - 137 - tr oubleshooting 7 error messages for scanning the following messages are displayed on the display screen while using the scan function. Communication error to close blinks fax transmission and reception is canceled due to errors. Telephone please see help for details. Lights ...

  • Page 138

    Error messages - 138 - writing failed please see help for details. To close blinks writing to the usb memory failed. Remove the write-protection of the connected usb memory. Usb memory disconnected. Please see help for details. To close blinks usb memory is not connected to the machine and the machi...

  • Page 139

    Error messages - 139 - tr oubleshooting 7 getting target ip failed. Please check dhcp settings. Please see help for details. Blinks the machine could not get ip address from dhcp server. Check the network configuration, cable connection and status, and the server status. Please check dns settings. P...

  • Page 140

    Error messages - 140 - error messages for printing please change file name. Please see help for details. To close blinks a file name was unauthorized by the server. Z change the file name. Z if using an ftp server to save data with scan to network pc, there are some machines that cannot be connected...

  • Page 141

    Error messages - 141 - tr oubleshooting 7 error pdf to close lights up a methodology error was detected in a pdf. Please check whether the pdf file opened correctly. Invalid password to close lights up this is a pdf file with the encryption function enabled. When printing an encrypted pdf file, open...

  • Page 142

    Error messages - 142 - access limitation error data was deleted due to the printing limitation. Please see help for details. To close lights up a print job sent by a user who is not authorized for printing is deleted. Warming up. Lights up the machine is warming up, or cooling down. Wait for a while...

  • Page 143

    Error messages - 143 - tr oubleshooting 7 checking the machine's status from the key from the status> key on the operator panel, you can check the status of your machine. Checking the trouble status the status> key blinks or lights up when any trouble is occurring in your machine. Press it to check ...

  • Page 144: Other Issues

    Other issues - 144 - z other issues this section explains the issues you may encounter while operating your machine and how to solve them. Unable to print from a computer memo z if the following information does not solve the trouble, contact your dealer. Z for troubles caused by an application, con...

  • Page 145

    Other issues - 145 - tr oubleshooting 7 network connection problems „ common to windows and mac os x „ for windows usb connection problems „ common to windows and mac os x cause remedy reference the job type of "secure print", "store to hdd" and "encrypted secure print" are unselectable on the mb491...

  • Page 146

    Other issues - 146 - „ for windows unable to install a printer driver successfully memo z if the following information does not solve the trouble, contact your dealer. Z for troubles caused by an application, contact the manufacturer of the application. Usb connection problems „ for windows cause re...

  • Page 147: Restrictions On Each Os

    Other issues - 147 - tr oubleshooting 7 restrictions on each os restrictions on windows 7/windows vista/windows server 2008 r2/ windows server 2008 item symptom cause/remedy printer drivers [help] is not displayed. The [help] function is not supported on ps printer drivers. The [user account control...

  • Page 148

    Other issues - 148 - restrictions on windows server 2003 service pack 1 and windows xp service pack 2 „ restrictions on windows firewall on windows server 2003 service pack 1 and windows xp service pack 2, the windows firewall functionality is enhanced. The following restrictions may apply to printe...

  • Page 149

    Other issues - 149 - tr oubleshooting 7 restrictions on mac os x 10.6 restrictions on mac os x 10.5 restrictions on mac os x 10.4 web driver installer unable to access the machine from a remote computer. Click [start] and then select [operator panel] > [security center] > [windows firewall]. Select ...

  • Page 150: Copying Issues

    Other issues - 150 - copying issues memo z if the following information does not solve your trouble, contact your dealer. Unable to copy symptom point to check remedy reference unable to copy. Is the machine turned on? Hold down the power switch for about a second to turn on the power. P.20 is the m...

  • Page 151

    Other issues - 151 - tr oubleshooting 7 the copied output is different from the original document troubles after starting to copy unable to copy. Is the continuous scan mode on? Select [scan completed] on the display screen. P.76 is the machine off line? Press the print> key on the operator panel, a...

  • Page 152: Faxing Issues

    Other issues - 152 - faxing issues memo z if the following information does not solve the trouble, contact your dealer. Unable to send a fax unable to receive a fax symptom point to check remedy reference unable to send a fax. Did you perform the correct procedure? Check the appropriate procedure an...

  • Page 153: Scanning Issues

    Other issues - 153 - tr oubleshooting 7 unable to send or receive a fax the machine does not select the appropriate paper for the received fax scanning issues memo z if the following information does not solve the trouble, contact your dealer. Symptom point to check remedy reference unable to send o...

  • Page 154: Image Quality Issues

    Other issues - 154 - image quality issues memo z if the following information does not solve your trouble, contact your dealer. Symptom point to check remedy reference vertical white lines appear. The led heads are dirty. Wipe the led heads with a soft tissue paper. P.167 the toner is low. Replace t...

  • Page 155

    Other issues - 155 - tr oubleshooting 7 horizontal lines and spots appear periodically. If the interval of lines or spots is about 94 mm (3.7 inches), the image drum (the green tube) is damaged or dirty. Lightly wipe the image drum with soft tissue paper. Replace the image drum if it is damaged. P.1...

  • Page 156: Feeding Issues

    Other issues - 156 - feeding issues memo z if the following information does not solve the trouble, contact your dealer. Nothing is printed. Two or more sheets of paper are fed simultaneously. Fan the paper well and load it again. P.32 the machine may be malfunctioning. Contact your dealer. - the ba...

  • Page 157

    Other issues - 157 - tr oubleshooting 7 z the paper often jams. Z multiple sheets are fed at once. Z the paper is fed at an angle. The machine is inclined. Place the machine on a flat surface. - the paper is too light or too heavy. Use the appropriate paper for the machine. P.29 the paper is moist o...

  • Page 158: Machine Issues

    Other issues - 158 - machine issues memo z if the following information does not solve the trouble, contact your dealer. Symptom point to check remedy reference turned on the machine, but it stays "off-line". The ac cable is unplugged. Hold down the power switch for about a second to turn on the pow...

  • Page 159

    Other issues - 159 - tr oubleshooting 7 there is an abnormal sound. The machine is inclined. Place the machine on a flat surface. - there is a piece of paper or unknown object inside the machine. Check the inside of the machine and remove any objects. - the top cover is open. Close the top cover. - ...

  • Page 160: When The Power Goes Out

    Other issues - 160 - when the power goes out machine behavior when the power goes out, the machine behaves in the following way: note z we do not warrant operation when an uninterruptible power system (ups) or inverter is used. Stored fax data „ backing up data in memory even if the power goes out o...

  • Page 161: 8. Maintenance

    - 161 - mai n te n ance 8 8. Maintenance this chapter explains how to replace consumables, clean the machine, and move or transport the machine. Z replacing consumable items this section explains how to replace consumable items. Note z use only genuine oki data consumable items to ensure optimum qua...

  • Page 162: Replacing Toner Cartridges

    Replacing consumable items - 162 - replacing toner cartridges procedure for replacement 1 open the top cover and remove the used toner cartridge. Memo z when disposing of used toner cartridges by necessity, poly-bag them, and be sure to follow instructions and regulations of your local government. R...

  • Page 163: Replacing The Image Drum

    Replacing consumable items - 163 - mai n te n ance 8 note z do not use solvents, such as methyl alcohol or thinners. They damage the led head. 4 close the top cover. 5 close the scanner unit. Memo z if you dispose of a toner cartridge by necessity, put it in a polyethylene bag or something and then ...

  • Page 164

    Replacing consumable items - 164 - align both guide posts of the image drum with their guide grooves on the printer, and gently set the image drum into the printer. Remove the toner cover (orange) from the image drum set in the printer by pushing the projection in the direction of the arrow. Memo z ...

  • Page 165: Cleaning Your Machine

    Cleaning your machine - 165 - mai n te n ance 8 z cleaning your machine this section explains how to clean each part of your machine. Cleaning the surface of the machine note z do not use benzine, thinners, or alcohol as a cleaning agent. They may damage the plastic parts of the machine. Z do not lu...

  • Page 166: Cleaning Paper Feed Rollers

    Cleaning your machine - 166 - cleaning paper feed rollers clean the paper feed rollers if paper jams occur frequently. For tray 1 and tray 2 memo z the following images use tray 1 as an example, but the same procedure applies to tray 2. 1 pull out the tray. 2 wipe the paper feed rollers (1) inside t...

  • Page 167: Cleaning Led Heads

    Cleaning your machine - 167 - mai n te n ance 8 cleaning led heads clean the led heads if vertical white lines appear, images are fading vertically, or the periphery of letters is smudged in the printouts. Dirt on the led heads may also cause paper jams. Note z do not use methyl alcohol or thinners ...

  • Page 168: Moving Your Machine

    Moving your machine - 168 - z moving your machine this section explains how to move or transport your machine. Moving your machine 1 hold down the power switch for about a second to turn on the power. Reference z "turning off your machine" (p. 20) 2 unplug all the cables. Z ac cable and ground wire ...

  • Page 169

    Moving your machine - 169 - mai n te n ance 8 9 protect your machine with packing materials. 10 lift your machine and put it in a box. Note z use the packing materials attached to your machine when purchased. Z remove the vinyl tape to secure the image drum and toner cartridges after transporting or...

  • Page 170: 9. Appendix

    - 170 - 9. Appendix this chapter explains the specifications of your machine and information on consumables and optional components. Z specifications „ general specifications mfp model model number mb461/es4161 mfp n22205a, n22205b mb471 n22206a, n22206b mb491/es4191 mfp n22208a, n22208b mb461/es416...

  • Page 171

    Specifications - 171 - appendix 9 „ copier specifications „ fax specifications „ pc fax specifications supported os z windows 7, windows vista, windows server 2008 r2, windows server 2008, windows xp, windows server 2003 z mac os x 10.4.0-10.7 please refer to "product requirements" (p. 43) mb461/es4...

  • Page 172

    Specifications - 172 - „ internet fax specifications „ scanner specifications „ scan to e-mail specifications „ scan to network pc specifications mb461/es4161 mfp mb471 mb491/ es4191 mfp communication protocol n/a smtp, pop3, mime file format n/a tiff mb461/es4161 mfp mb471 mb491/ es4191 mfp scanner...

  • Page 173

    Specifications - 173 - appendix 9 „ scan to usb memory specifications „ scan to local pc specifications „ printing specifications mb461/es4161 mfp mb471 mb491/ es4191 mfp connectivity interface usb2.0 host if storage device usb memory (up to 32 gb) not all usb memory products are guaranteed to work....

  • Page 174

    Specifications - 174 - paper size tray1 legal 13/13.5/14, letter, executive, statement, a4, a5, b5, a6, 16k (197 x 273 mm, 195 x 270 mm, 184 x 260 mm), custom size tray2 (optional) legal 13/13.5/14, letter, executive, a4, a5, b5, 16k (197 x 273 mm, 195 x 270 mm, 184 x 260 mm), custom size mp tray - ...

  • Page 175

    Specifications - 175 - appendix 9 „ print from usb memory specifications „ network specifications conditions for the guarantee of print quality temperature 10°c, humidity 30 to 78% rh/ temperature 32°c, humidity 30 to 54% rh/ humidity 30% rh, temperature 10 to 32°c/ humidity 80% rh, temperature 18 t...

  • Page 176: Basic Steps In Windows

    Basic steps in windows - 176 - z basic steps in windows these are the steps for displaying the driver setting window from [printer] / [printer and fax] folder for windows os used for examples in this manual other than windows 7. Memo z the steps for windows server 2008 r2 are the same as for windows...

  • Page 177: Index

    - 177 - inde x index symbols -(hyphone) ................... 81 *(asterisk) .................... 81 #(hash symbol) ............ 81 a access control ............. 119 actkey ......... 100, 105, 106 address book .......94, 102, 110 adf ............................. 38 administrator password ..............

  • Page 178

    Index - 178 - n network configuration .... 97 network scan destinations ......... 112 o one-touch key .... 26, 82, 90, 92, 102 p paper feed ............. 74, 117 paper jams ................. 126 paper size ... 29, 32, 36, 113 paper tray ...............32, 36 paper weight (document) ........... 38 pa...

  • Page 179: Oki Contact Details

    Okicontactname. Oki systems (uk) limited okicontactaddress.550 dundee road slough trading estate slough berkshire sl1 4le tel:+44 (0) 1753 819819 fax:+44 (0) 1753 819899 http://www.Oki.Co.Uk oki systems ireland limited the square industrial complex tallaght dublin 24 tel:+353 (0) 1 4049590 fax:+353 ...

  • Page 180

    Oki printing solutions herstedøstervej 27 2620 albertslund danmark adm.: +45 43 66 65 00 hotline: +45 43 66 65 40 salg: +45 43 66 65 30 fax: +45 43 66 65 90 website: www.Oki.Dk oki systems (finland) oy polaris capella vänrikinkuja 3 02600 espoo tel: +358 (0) 207 900 800 fax: +358 (0) 207 900 809 web...

  • Page 181

    Www.Okiprintingsolutions.Com oki data corporation 4-11-22 shibaura, minato-ku,tokyo 108-8551, japan 44917102ee rev2.