Mc560 mfp cx2032 / cx2033 mfp service & troubleshooting guide revision 2.0 disclaimer every effort has been made to ensure that the information in this document is complete, accurate, and up to date. The manufacturer assumes no responsibility for the results of errors beyond its control. While all r...
2 contents maintenance procedures – printer / adf / scanner…..3-6 exterior cleaning……………………………………………………………3 cleaning inside the printer…………………………………………………..3 cleaning the led lens array………………………………………………...4 cleaning the pickup roller…………………………………………………..5 cleaning the adf and scanner………………………………………...
3 maintenance procedures – printer / adf / scanner cleaning the exterior of the printer * be sure to turn off the power to the printer. Clean the interior and exterior with a soft clothe and a vacuum cleaner. Note: be careful not to touch the image drum terminals, led lens array, and led connectors....
4 raise the fuser lock levers and remove the fuser. Use caution: fuser will be hot! Clean the interior of the printer with a dry, lint free clothe and a vacuum. Cleaning the led heads * be sure to turn off the power to the printer. Open the top cover by pressing the open button and wipe the four led...
5 cleaning the pickup rollers * be sure to turn off the power to the printer. Remove the paper cassette and clean the rollers with a damp clothe. Clean the separation pad on the cassette with a damp clothe..
6 cleaning the document glass * be sure to turn off the power to the printer. Open the automatic document feeder and clean the document glass with a damp clothe. Cleaning the adf clean the feed roller and separation pad with a damp clothe..
7 self diagnostics lcd message list when the printer detects an irrecoverable error, it displays a service call error in the lcd like the one given below: when a service call error is issued, an error code is displayed in the lower line of the lcd, accompanied by the relevant error information. Be s...
8 wait a moment network initial error varies this appears when the nic initialization is occurred, as the setting was changed. Load %media_size% %errcode%:%tray% empty 491 492 printing request is issued to an empty tray. Load paper. (it takes a while until the status disappears after you have closed...
9 trust paper %errcode%:error 424 density of the destination image for woven pattern is greater than that of the woven pattern. A user must take measures such as increasing density of the woven pattern or decreasing density of the input image. Displays a warning on the operation panel as waiting for...
10 genuine toner is recommended %errcode%:non genuine %color% toner 550 551 552 553 the signature id of toner cartridge can not be recognized (unauthorized third party). As probable missing to measure the amount of toner, the printer notifies error status and stop printing. Error 550 : y error 551 :...
11 replace image drum %errcode%:%color% drum life 350 351 352 353 the life of the image drum (alarm) error 350 : y error 351 : m error 352 : c error 353 : k warning status takes effect at cover open/close. Replace image drum %errcode%:%color% drum life 560 561 562 563 the toner empty error is occurr...
12 check data rec data error an error has happened while the printer is receive processing the download data. %dlcode% 1: file size error 2: check-sum error 3: invalid printer model number 4: invalid module i/f version 5: invalid fat version wait a moment data writing the printer is writing the down...
13 power off/on %errcode%:fatal_error fatal 002 011 f0c f0d ffe fff a fatal error occurred. For more information, see "service calls list." power off/on %errcode%:download error fatal 209 downloading media table to pu has failed. (related to custom media type.) error messages.
14.
15.
16.
17.
18.
19.
20
21.
22.
23.
24.
25 self diagnostic service error codes error message cause description y / n solution service call 001:error (c5900) machine check exception hardware fault detected. (board defective or shortage of power supply volume) replace tbh pcb. Power off/on 002 ~ 005 error 006 / 007 error cpu exception is th...
26 is cu fan connector set properly? No connect properly. Service call 051:error(c5900) cu fan error abnormal cpu cooling fan on cu board. Is error recovered by replacing fan? Yes no replace fan. Replace tbr pcb. Service call 052:error(c5900) dma abort error detected in image processor. Does error r...
27 is cable between pu board and high-voltage power unit connected properly? No yes connect properly. Check improper connections for hv. Service call 121:error high-voltage power supply i/f error. Is there no improperly connections? No replace high-voltage power supply. Is fan in low-voltage power s...
28 is toner cartridge set? No set toner cartridge. Is toner lock lever set? No turn a lock lever of toner to lock service call 160 ~ 163 error error detected by toner sensor. 160= y, 161 = m, 162 = c, 163 = k does error reoccur? Yes replace toner sensor or assembly. Is an error message indicated? Ye...
29 power off/on error codes 203,204, 207, 208, 214, foc, fff f0d: error(c5900) ffe: error(c5900) an error was detected of the cu program. Reinstall the cu board. Is the error message displayed again? After turn power off, check connections between cu board and pu board. Then turn power on again. Ser...
30 service call 980:error error by media clinging to the fuser media has clung to the fuser. Yes power off. Replace the fuser unit. Sdram error pu board sram error does error reoccur? Yes turn on the printer again. Replace the pu board (prf). Xxxxxxxxxxxxxxxx crc check ng a pu download data crc chec...
31 system maintenance/adjustments user's maintenance menu this is a maintenance menu category among the normal menu categories. (different from the system maintenance menus) the items that can be set under this menu are indicated below. Shaded areas are default setting. Operator panel display catego...
32 indication of consumable part counters this self-diagnosis is practiced to indicate the consumed states of consumable parts. 1. Activate the normal self-diagnostic mode, and press and hold down the [menu+] key or [menu-] key, until "consumable status" appears in the display section, and then, pre...
33 indication of printed page counters this self-diagnosis is practiced to indicate the current number of printed pages of the printer. 1. Activate the normal self-diagnostic mode, and press and hold down the [menu+] key or [menu-] key, until "printer status" appears in the display section, and then...
34 setup of self-diagnostic function this self-diagnosis is practiced to enable/disable the error detections of the different types of sensors. The error detections can be disabled or enabled temporarily for troubleshooting purposes. However, this function should be exercised with utmost care, since...
35 *shaded areas are default settings indication set value operation of set value function enable detects. Toner sensor disable does not detect. For enabling/disabling toner sensor operation. Enable checks belt unit check disable does not check. For enabling/disabling checking operation for mounted ...
36 switch scan test this self-diagnosis is practiced to check the inlet sensors and switches. 1. Activate the self-diagnostic mode (level 1), press and hold down the menu+ or menu- key, until "switch scan" appears in the upper line of the display section, and then, press the enter key. (the menu+ ke...
37 motor clutch test this self-diagnosis is practiced to test motors and clutches. 1. Activate the self-diagnostic mode (level 1), press and hold down the menu+ or menu key, until "motor & clutch test" appears in the upper line of the display section, and then, press the enter key.(the menu+ key inc...
38 normal printing drive. (clutches that cannot be driven individually due to their structural reason are driven along with their motors.) * "id up/down" continues being driven, until the "cancel" key is depressed. The motor keeps rotating if holding down the [enter] key for two seconds when determi...
39 test print this self-diagnosis is practiced to print test patterns built in pu. Other test patterns are stored in the controller. This print should not be used to check the print quality. To diagnose abnormal images, follow section 7. 1. Activate the self-diagnostic mode (level 1), press and hold...
40 color setup - pressing the enter key after selecting on causes the data indicated below to appear on the panel. Print setup for each color - pressing the menu+ key or menu- key activates shifting. Pressing the online key or cancel key switches between on and off. Pressing the back key restores th...
41.
42 • when print is executed, the following message is displayed: p: number of test-print pages (unit: sheets) w: print wait time (unit: seconds) • pressing the menu+ key switches over the indication. U: *** = measured value of upper heater temperature [unit: ˚c] [###] = target temperature for print ...
43 etmp: hopping motor constant-speed correction parameter (environmental temperature)[unit: dec] utmp: fuser motor constant-speed correction parameter (target fuser temperature) [unit:dec] reg: hopping motor constant-speed timer value (i/o set value)[unit: hex] ext: fuser motor constant-speed timer...
44 color registration adjustment test this self-diagnosis is practiced to conduct testing on the color registration function of the printer and to locate the cause of color drift. Restore the normal operation of the printer by following the troubleshooting procedure if any error is issued during the...
45 print density adjustment test this self-diagnosis is practiced to conduct testing on the print density adjustment function of the printer and to view the execution result. This test is executed also to judge whether the print density adjustment mechanism is normal or abnormal. 1. Activate the sel...
46 fax user settings (for further information see cx2032 user’s guide page 38) item description or choice phone book edit speed dial! Edit group dial! Delete speed dial! Delete group dial! Delete all! Append phone #: off/on reports: activity report transmission report transmission report broadcast r...
47 fax maintenance menu (service mode) to access the fax maintenance (service mode) menu depress the #2 key while powering on the machine. The following screen will appear: this will allow service mode access in the regular user printer menu. To de-activate the service mode access cycle the power of...
48 troubleshooting basic troubleshooting procedure.
49.
50
51.
52 paper feed troubleshooting.
53.
54.
55.
56.
57.
58.
59.
60
61.
62.
63.
64.
65.
66.
67.
68.
69.
70
71.
72.
73 service error code/hardware troubleshooting.
74.
75.
76.
77.
78.
79.
80
81 image quality troubleshooting.
82.
83.
84.
85.
86.
87.
88 network troubleshooting.
89.
90 basic fax troubleshooting for more detailed information of machine fax settings refer to “setting the fax facility” in the cx2032 mfp user’s guide pages 58 to 65. The mfp will not dial a telephone number check the power cable and wall outlet. Make sure that the telephone line (not external teleph...
91 local mfp will not answer the telephone or receive faxes first check to see that the power cord is connected properly. Also check the reception mode setting of the machine. This mfp will not receive faxes automatically if the manual receive mode is enabled ( see “manual receive” on page 64 in the...