241013-20 neo16 5055.700 installation and operating instructions safety notice if this stove is not properly installed, a house fi re may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirement...
2 neo16 241013-20 please save these instructions note: we strongly recommend that smoke detectors be installed. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to curing of stove paint or fumes caused by accidentally leaving ...
241013-20 neo16 3 creosote formation and need for removal when wood is burned slowly, it produces tar and other or- ganic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney fl ue of a slow burning fi re. As a result, creosote ...
4 neo16 241013-20 caution: never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fl uid or similar liquids to start or "freshen up" a fi re in this heater. Keep all such liquids well away from the heater while it is in use. Caution: hot while in operation. Keep children, cloth- ...
241013-20 neo16 5 ash removal caution: ashes are to be removed only when the heater is cold. Whenever ashes get 3 to 4 inches deep in your fi rebox, and when fi re has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1" (25 mm) deep on the fi rebox bottom to help maintain ...
6 neo16 241013-20 1. Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is necessary to burn wet or unseasoned wood, do so ...
241013-20 neo16 7 maintenance checks check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (see website for descriptions and more detail) some warping of the baffle is normal(up to 1/4” or .65cm). Replace if the baffle has permanent warp...
8 neo16 241013-20 36 15/16" 36" 27 1/8" 20 1/8" 17 7/16" 6" neo 1.6 dimensions crate removal 1) carefully remove wood top and supports. 2) remove plastic cover. 3) using a 7/16" wrench, remove lag bolts that secure stove body to bottom pallet. Side panel installation 1) remove the upper grill by rem...
241013-20 neo16 9 3) engage the tabs in the panel into the slots in the panel mounting bracket. Fig. #2 4) attach the panel to the rear shield. Secure with two screws. Fig. #3 fig. #2 fig. #3 screws.
10 neo16 241013-20 8" [203mm] 16" [406mm] 8" [203mm] canada only floor protector the stove may be installed on a combustible fl oor provided noncombustible ember protection is used. This protection must extend as follows: in canada: 18" (457 mm) on the fi ring side and 8" (203 mm) to the other sides...
241013-20 neo16 11 warning: under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It may be fi red only after the following conditions have been met. * do not attempt to connect this heater to any air distribution duct. * outside combustion air or fresh air into...
12 neo16 241013-20 5" 21 1/2" 11" 8" 3" 15" 3" mobile home minimum clearance to combustibles warning: under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It may be fi red only after the following conditions have been met. - do not connect this unit to a chimne...
241013-20 neo16 13 fig. #8 chimney roof fl ashing storm collar * 4" diameter air inlet with rodent screen * if the crawl space is well ventilated it is not necessary to extend air inlet to outside spark arrestor rain cap radiation shield chimney connector chimney support 47.5" (1207 mm) minimum mini...
14 neo16 241013-20 the optional blower kit (wodc.Blow) is equipped with a three prong power cord and may be installed at any time. Follow installation instructions supplied with the kit. Route power supply cord away from heater. Electrical rating: 115 volts a.C., 60hz, .5 amps. Fan output rating: 12...
241013-20 neo16 15 troubleshooting problem cause cure glass is dirty 1. Wood is wet - use dry wood 2. Turning down air control - do not turn down until or damper too soon a) there is a good bed of coals b) the wood is charred 3. Draft too low - improper chimney height and / or diameter - chimney plu...
16 neo16 241013-20 replacement parts - neo 1.6 (when ordering, include part number with description) item description part no. Item description part no. 2............ Embossed panel set .................... Ne16.78375xx 3............ Door catch .......................................... Ne16.7825 4....
241013-20 neo16 17 ish. This clean charcoal burning stage will last for a considerable length of time and refuelling should be avoided until the charcoal base has become quite small. Operating tips 1. Always use dry, seasoned fi rewood, up to 18" long. Load wood, a mixture of large and small pieces,...
Item/ article dimensions part number/ numÉro de piÈce a 1 1/2” x 4 1/2” x 1 1/4” (39 mm x 115 mm x 32 mm) 248.0 b 3” x 4 1/2” x 1 1/4” (77 mm x 115 mm x 32 mm) 247.0 d 9” x 4 1/2” x 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 neo 1.6 firebrick installation instructions this package contains 13 full-siz...
Label a. 12 in. / 305 mm 12 in. / 305 mm b. 12 in. / 305 mm 12 in./305 mm c. 8 in. / 203 mm 8 in. / 203 mm d. 25.5 in. / 597 mm 25.5 in. / 597 mm e. 14.8 in. / 325 mm 14.8 in./325 mm f. 16.8 in. / 427 mm 16.8 in. / 427 mm a. 8 in. / 203 mm 8 in. / 203 mm b. 5 in. / 127 mm 5 in. / 127 mm c. 3 in. / 7...
Pacific energy fireplace products ltd. 2975 allenby rd., duncan, b.C. V9l 6v8 phone: 250-748-1184 web site: http://www.Pacifi cenergy.Net printed in canada.
