220114-20 neo 1.6 insert-a 5055.750 installation and operating instructions model: neo 1.6 insert series: a safety notice if this stove is not properly installed, a house fi re may result. For your safety, follow the installation instructions. Contact local building or fi re officials about restrict...
2 neo 1.6 insert-a 220114-20 contents safety ............................................................................................ 3 dimensions ............................................................................................ 3 clearances ..............................................
220114-20 neo 1.6 insert-a 3 ರ 16” 18” 9 3/4 ” 13 1/2” clearances masonry or factory built fireplace the minimum required clearances to surrounding combustible materials when installed into a masonry or factory built fi replace are listed below and in fig. #1. Minimum clearances to combustibles adja...
4 neo 1.6 insert-a 220114-20 16” non-combustible fi replace hearth 30” 20” 16 1/4” 8” 8” fireplace hearth requirements: (measured without the insert) the hearth can be fl ush with an adjacent combustible fl oor and must extend 16” in front and 8” beyond each side of the fi replace opening. Ember pro...
220114-20 neo 1.6 insert-a 5 creosote formation and need for removal when wood is burned slowly, it produces tar and other or- ganic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney fl ue of a slow burning fi re. As a result...
6 neo 1.6 insert-a 220114-20 operation wood selection this heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or too green or freshly cut hardwoods. Wood should be properly air dried...
220114-20 neo 1.6 insert-a 7 over firing over fi ring can be caused by operating the unit with the door open, damage to door gaskets allowing excess air to enter the fi rebox, the use of kiln dried lumber, mill ends or paper waste and prolonged or continual use on a high burn setting. More wood, mor...
8 neo 1.6 insert-a 220114-20 warning: do not overtighten, tighten screws very carefully. - do not clean glass when hot - do not use abrasive cleaners on glass 6. Do not store wood within heater installation clearances, or within the space required for fuel loading and ash removal. Keep the area arou...
220114-20 neo 1.6 insert-a 9 blower replacement 1. Remove the surround front by lifting and pulling away from the unit. Remove the four screws securing the back surround to the brackets and set them aside carefully to avoid damage. 2. Remove the surround mounting bracket by removing the two screws s...
10 neo 1.6 insert-a 220114-20 the power cord for the neo 1.6 insert comes factory set to exit the right side of the unit. If you desire, the cord can be switched to exit to the left of the unit. The cord will lose ap- proximately 12” of length when exiting the left side of the unit. Follow these ins...
220114-20 neo 1.6 insert-a 11 maintenance checks check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (see website for descriptions and more detail) weekly: - firebrick - visual, for cracking. - door gasket - sagging, placement, damage....
12 neo 1.6 insert-a 220114-20 installation your insert is designed to be installed into an approved ma- sonry or factory built zero-clearance fi replace. The masonry fi replace must be built according to the requirements of the standard of chimneys, fireplaces, vents and solid fuel burning appliance...
220114-20 neo 1.6 insert-a 13 4) push the insert into position inside the fi replace and at- tach the fl ue collar to the opening in the top of the insert fi rebox. Use the rear adjusting legs to level the insert. 5) measure, trim and shape a top fl ashing to fi t the existing chimney fl ue. Plan fo...
14 neo 1.6 insert-a 220114-20 surround assembly and installation 1) attach the surround back to the surround mounting brackets on the unit with the four screws provided.Fig. #7 2) push the entire appliance back until the surround assembly is in contact with the fi replace. 3) attach the front surrou...
220114-20 neo 1.6 insert-a 15 blower the insert comes equipped with variable speed circulating air blowers. The blower system is thermostatically controlled for automatic operation, as well manually with a convenient bypass switch. Blower operation automatic: to operate the blower automatically, pus...
16 neo 1.6 insert-a 220114-20 troubleshooting problem cause cure excessive creosote 1) wood is too wet - use dry wood buildup 2) turning down air control - do not turn down until: too soon a) there is a good bed of coals b) the wood is charred 3) draft too low - improper chimney height and/or diamet...
220114-20 neo 1.6 insert-a 17 neo 1.6 insert firebrick installation instructions this package contains 14 full-size fi rebricks. With the heater in the upright position, install fi rebricks as follows: - first, install 4 fi rebricks against the rear wall. - next, install the side fi rebricks, 3 each...
18 neo 1.6 insert-a 220114-20 1......Top casing ......................................................................... 7834 2......Side casing, lhs ............................................................ 7841.2 3......Side casing, rhs ............................................................
220114-20 neo 1.6 insert-a 19 label minimum clearance to combustibles (measured from insert door opening) dÉgagement minimum aux combustibles a) adjacent sidewall/ 381 mm / 15 in paroi latÉrale adjacente b) side facing/ 286 mm / 11.25 in revÊtement latÉral (measured from insert surround brow) c) top...
Pacific energy fireplace products ltd. Phone: 1-250-748-1184 web site: http://www.Pacifi cenergy.Net 2975 allenby rd., duncan, b.C. V9l 6v8 pacific energy fireplace products ltd. Phone: 1-250-748-1184 web site: http://www.Pacifi cenergy.Net 2975 allenby rd., duncan, b.C. V9l 6v8 printed in canada.
