Owner's manual assembled in japan indigo series preamplifier qualia & co. Of america.
Introduction thank you for purchasing the q ualia indigo series preamplifier. Please read this owner's manual thoroughly before using the product so that its high-quality audio can be enjoyed for years to come. If you have any questions, please contact the dealer where you purchased the product or q...
How to use audio equipment correctly before using the product, please read the safety precautions and owner's manual thoroughly and use the product correctly. Keep this owner's manual at hand for future reference. ● symbols the safety precautions and the product use various symbols to help users use...
3 indigo line main unit input selector volume control input a – c: rca connectors input d – e: xlr connectors ( pin 2 hot +) output 1 : rca connectors output 2 : xlr type connectors ( pin 2 hot +) power in (fischer connector): a connector used to connect the power cable from the indigo series power ...
Power indicator indigo pre power supply (1) front panel (2) rear panel (3) power cables 4 120 5 power switch lch power outlet (fischer connector) rch power outlet (fischer connector) ac power inlet (15 amp iec type) fusebox voltage indication (operate the power supply only at the voltage indicated) ...
5 positioning and location of the units install this equipment in a location with adequate space for ventilation and heat release. If this equipment is installed in a location where it will be exposed to direct sunlight, extremely high temperature (for example near a heater), high humidity, or dust,...
6 main unit power supply main unit power supply (1) installation recommended by qualia & co. Install the indigo preamplifier main unit on a top panel of a sturdy rack if possible. Install the power supply separately from the main unit. (2) when installing this equipment on a middle shelf of a rack i...
7 connection of power cable note: be sure to connect the power cable before connecting the ac power cord. Connecting cables in an incorrect order may damage the main unit and result in an electric shock. Be sure to connect the cables as described below. Warning connect the power cable into the power...
1. Set the power switch on the power supply to off. 2. Disconnect the ac power cord from the power outlet on the wall (or power strip). 3. While supporting the main unit with one hand, hold and pull the latching sleeve of the fisher connector of the power cable using the other hand. The lock is rele...
9 ● when connecting a cable, confirm that the power cable is not connected. Connecting a cable with the power on may damage the main unit and the equipment to be connected, which may result in an electric shock. ● before connecting equipment, thoroughly read the instruction manual for each device an...
10 note: this device is not a balanced amplifier. When connecting a balanced cable, be sure to match the polarity of the equipment to be connected with this device. If a cable needs to be customized so that it can be connected properly, please contact the dealer or cable manufacturer. If the polarit...
11 ● when connecting a cable, confirm that the power cable is not connected. Connecting a cable with the power on may damage the main unit and the equipment to be connected, which may result in an electric shock. ● before connecting, thoroughly read the instruction manual of the power amplifier, tur...
12 ● when connecting a cable, confirm that the power cable is not connected. Connecting a cable with the power on may damage the main unit and the equipment to be connected, which may result in an electric shock. ● before connecting equipment, thoroughly read the instruction manual for the power amp...
● before connecting the ac power cord, confirm that cables are properly connected to input/output terminals and the power switch is set to off once again. ● do not place heavy articles on the power cord. Confirm that the cord is not crushed under this equipment. A damaged power chord can cause fire ...
14 ● basic operation ● before turning on the power, confirm that cables are properly connected once again. ● before turning on the power, be sure to confirm that the volume of the indigo preamplifier is lowered to the minimum. Turning on the power of this equipment with a high volume may damage the ...
15 (3) select a program source. Select a program source to be used using the input selector equipped on the front panel of the main unit. Input selector volume control the input select knob can be found on the left side of the front panel. (4) set the volume to a desired level. Play a record or cd o...
(6) turn off the power. Follow the steps below to turn off the power. Lower the volume of the preamplifier to the minimum, turn off the power of the power amplifier, and then turn off the power of this equipment. Follow the steps below to turn off the power: tips for enjoying higher quality sound in...
17 do not detach the rear cover of the main unit, cabinet, or cover. Do not modify this equipment. This device contains high-voltage parts. In order to prevent electric shock, please contact the dealer or the service department of qualia & co. For inspection, maintenance, or repair of the inner part...
18 ● maintenance before servicing or moving this device, be sure to turn off its power switch, pull out the power plug from the wall socket, and disconnect external connection cables. Damaged cords can cause fire or electric shock. To clean this equipment, wipe it with a soft cloth such as commercia...
