Electric fireplace heater i n s t r u c t i o n m a n u a l m903l-48bho/bdc ndf-68n attention: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you read all instructions..
2 s a f e t y i n s t r u c t i o n s important please note when you open the carton carefully check the unit and make sure there are no damages. If you have any problems with the unit, with how the various functions work or with hidden damages or missing parts please call 1-800-459-4409 (est) immed...
3 7) this electric fireplace heater is not in- tended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 8) do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings....
4 this electric fireplace heater is for use on 120 volts. The cord has a plug as shown at a in illustration below. An adapter as shown at c is available for connecting three-blade grounding-type plugs to two-slot recep- tacles. The green grounding plug extend- ing from the adapter must be connected ...
5 a s s e m b ly i n s t r u c t i o n s parts list: fireplace insert 1 a) top panel 1 b) base panel 1 c) left outer side panel 1 d) right outer side panel 1 e) left inner side panel 1 f) right inner side panel 1 g) lower back panel 2 h) middle front panel 1 i) left upper side panel 1 j) right upper...
6 a s s e m b ly i n s t r u c t i o n s note: each plastic connector is pre-assem- bled (pre-drilled) on the specific panels with 2 screws. If the kd screw(s) do not fit during assembly, loosen the 2 (pre-drilled) screws to adjust the plastic connector until the kd screws are able to be installed. ...
7 step 6: attach panel k to panels c, d, e and f with 6 kd screws. See fig. F. Fig. F step 7: attach panel i and j to panel k with 4 kd screws. See fig. G. Fig. G step 8: attach panel l to panel k with 3 kd screws. See fig. H. Fig. H step 9: attach panel a to panel i and j with 7 kd screws. See fig....
8 step 11: attach 4 door hinges to left and right door [q and r] with 8 mounting screws [t] (2 screws for each hinge) as shown in fig k. Attach left and right door [q and r] to panel c and d with 8 mounting screws [t] (2 screws for each hinge). See fig. K. Attach door handles [rs] to left and right ...
9 o p e r a t i o n of 1875 watts. Once the fireplace insert has been properly connected to a grounded electrical outlet, it is ready to operate. Operation by the control panel the controls are located behind the grill below the front glass and can be accessed by pulling the grill from the top, forw...
10 maintenance warning: disconnect power and unplug the power cord before attempting any main- tenance or cleaning to reduce the risk of fire, electric shock or damage to persons. The bulbs in your unit can become extremely hot. Allow at least 10 minutes between turn- ing off the unit and removing t...
11 r e p a i r s e t fig. A repairs if any problems are found with the origi- nal parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of the following method. Tools required: electric drill, drill bits 3/4 inches (10 mm) or 1/16 inches ...
12 fig. E option 2: use the small l-brackets and screws 1. Place the small l-bracket to the unit as shown and mark the drill-holes on the mantel as shown in fig. F. Fig. F 2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8 mm) on the mantel. Each small l-bracket needs 4 hol...
13 either repair or replace the unit. It will have to be returned to us freight prepaid and we will return the repaired or replaced unit to you freight prepaid. The company’s sole obligation is to repair or replace the unit. This warranty is void if in the opinion of quality craft the unit has been ...
