Www.Ramsetinc.Com.
Jet ramset www.Ramsetinc.Com 1 do not install this gate operator if you do not have experience or appropriate training with gate operators. Warning important safety requirements & instructions ...................................................................................1 responsibilities of in...
Ramset www.Ramsetinc.Com jet 2 installation •read and understand the instruction manual before attempting any installation. •do not exceed the equipment specifications. •insure a safe and proper installation. •install this equipment in accordance with the ul 325 specifications. •make sure to elimina...
Jet ramset www.Ramsetinc.Com 3 prior to installation, the following must be observed: (per ul 325.56.8.4). A) install the gate operator only when: 1. The operator is appropriate for the construction of the gate and the usage class of the gate, 2. All openings of a horizontal slide gate are guarded o...
Ramset www.Ramsetinc.Com jet 4 vehicular horizontal slide-gate operator (or system) - a vehicular gate operator (or system) that controls a gate which slides in a horizontal direction that is intended for use for vehicular entrance or exit to a drive, parking lot, or the like. Vehicular swing-gate o...
Jet ramset www.Ramsetinc.Com 5 general specifications warning do not exceed the specifications. The warranty on your unit will be void if the installation exceeds the recommended specifications. Front bracket rear bracket star 24 motor 1 24 volt dc output to jet motor 120 vac – black neutral – white...
Ramset www.Ramsetinc.Com jet 6 positive stops and emergency release adjust on the open position adjust on the closed position emergency release the emergency release handle is located on the top of the jet arm. Insert the key into the emergency release handle and turn it in order to unlock the relea...
Jet ramset www.Ramsetinc.Com 7 gate operator installation installation details 1 3/4 below level level line caution: to avoid damage to gate and gate operator, do not weld jet bracket directly onto gate pickets. Caution: weld the jet bracket onto a solid frame member across the full length of the ga...
Ramset www.Ramsetinc.Com jet 8 maximum gate size & weight 8’ @ 400 lbs maximum gate size & weight 14’ @ 600 lbs –– 12’ @ 800 lbs steel square tubing 4x4 gate closed gate rotation center (hinge) outside property inside property 28½” 5¼” 5” top view g a t e compact installation standard installation 3...
Jet ramset www.Ramsetinc.Com 9 installation guideline 90º opening a (in) b (in) c (in) 5” 5¼” 28½” 5¾” 5½” 28½” 5¼” 5½” 28½” 6” 5¾” 28½” 6¾” 6¼” 28½” 7½” 5¼” 28½” 110º opening a (in) b (in) c (in) 5” 6¼” 28½” 5¾” 6” 28½” 4¾” 6” 28½” 4¾” 6¼” 28½” 5¼” 6” 28½” 6” 6” 28½” 1) measure the distance a from ...
Ramset www.Ramsetinc.Com jet 10 terminal strip connections star control board program remote radio dip switches 8–partial 7–one-pass 6–kick-back 5–lock 4–pho 2/ edge 3–timer 2–radio cycle 1–mode + + + + speed erd timer delay mot 1 mot 1 mot 2 mot 2 neutral 120 vac com com com com com safety phan rad...
Jet ramset www.Ramsetinc.Com 11 terminal strip connections terminal #1 – common low voltage common. Terminal #2 – safety normally closed. Becomes active with an open con- tact to common. If the gate is closed, it will have no effect. If the gate is opening, it will have no effect. If the gate is ope...
Ramset www.Ramsetinc.Com jet 12 trim adjustments – potentiometers trim pots use the “speed” trimmer to adjust the voltage with which the motor is powered during operation. Increasing/ decreasing this trimmer will affect the speed and torque with which the operator functions. Speed the “erd” trimmer ...
Jet ramset www.Ramsetinc.Com 13 dip switch dip switch configuration dip switch 1 – mode on the control unit is in slow mode. This setting is suitable for all gates. Off (used on gates under 6 ft) the unit is in fast mode. Make sure that the gate does not strike too hard against the mechanical stops ...
Ramset www.Ramsetinc.Com jet 14 loop installation ramset gate operators should always be installed with non-contact sensing devices such as loop detectors, photo eyes or the equivalent. Reversing loop (safety loop)prevents the gate from closing when a vehicle is in the loop area. The reversing loop ...
Jet ramset www.Ramsetinc.Com 15 reversing photo eye prevents the gate from closing when a vehicle has broken the beam of the photo eye. The photo eye will either stop the gate movement or reopen the gate when activated. Pho 2 photo eye prevents the gate from opening or closing when a vehicle has bro...
Ramset www.Ramsetinc.Com jet 16 master slave installation motor 2 motor 1 star control board program remote radio dip switches 8–partial 7–one-pass 6–kick-back 5–lock 4–pho 2/ edge 3–timer 2–radio cycle 1–mode + speed + erd + timer + delay mot 1 mot 1 mot 2 mot 2 neutral 120 vac com com com com com ...
Jet ramset www.Ramsetinc.Com 17 make sure that the jet gate operator has been properly installed and the physical limits on the undercarriage of the jet arm have been set to the open and close positions. Use the emergency release handle to move the gate to a half – open position then reengage the re...
Ramset www.Ramsetinc.Com jet 18 main block terminal hookup ant 1. Antenna signal 2. Antenna sock 3. Opening limit switch - motor 1 4. Closing limit switch - motor 1 5. Terminals 3, 4, 6, 7 common (limit switches) 6. Opening limit switch - motor 2 7. Closing limit switch - motor 2 8. Flashing lamp ne...
Jet ramset www.Ramsetinc.Com 19 lcd-kp liquid crystal display-keypad 1,024 codes 5,112 event log lcd display 7-day timer time zones latching stainless steel faceplate fire box allows the fire department to open the gate in case of an emergency. Key switch box suitable for use on entry doors where ac...
Ramset www.Ramsetinc.Com jet 20 important information for the homeowner ask your technician about all the features of our new ramset operator. Safety devices, such as reversing loops, phantom loops, photo eyes, or miller edges must be installed on your gate before the operator may be used. Ask your ...
Jet ramset www.Ramsetinc.Com 21 gate entrance safety precautions 1. Never let children operate or play with gate controls. Keep the controls away from children. 2. The entrance is for vehicles only. Pedestrians should use a separate entrance. 3. Always keep people, children and objects away from the...
9116 de garmo ave. Sun valley, ca 91352 tel: (818) 504-2533 • fax: (818) 504-1141 www.Ramsetinc.Com.
