RAMSET JET Instruction Manual - Jet
JET
RAMSET
www.ramsetinc.com
17
Make sure that the jet gate operator has been properly installed and the physical limits on the undercarriage of the jet arm have been set to
the open and close positions. Use the emergency release handle to move the gate to a half – open position then reengage the release handle
and apply pressure to the gate until it locks in place.
Program the operator using these steps:
The jet will automatically proceed to a learning mode. It will open the gate for 5 seconds (see important note below) and close the gate all the
way, then it will open the gate again all the way and close the gate.
Programming is now complete.
IMPORTANT: If during the initial programming the gate begins to close instead of open, stop the procedure by shutting off the power
and reverse the MOT 1 wires on the terminal strip. This will reverse the polarity of the motor. Repeat the programming procedure.
PROGRAMMING PROCEDURE
Step 1
Step 2
Step 3
Locate the “PROGRAM” button on the
Star 24 control board. The red LED
lights; PH and STP should be on.
Press and hold the Program button for
about 2 seconds. The red LED lights
will go out. Release the Program button
when the red LED’s go out.
The red LED lights will come back on and
the yellow LED will now begin to flash.
Press the Program button again and re-
lease it immediately.
RADIO TRANSMITTER PROGRAMMING PROCEDURE
Step 1
Step 4
Step 2
Step 5
Step 3
Locate the “REMOTE” button on
the Star 24 control board. The red
LED lights PH and STP should be
on.
If you have more than one remote control that
you wish to program you can program them
all at this time. Simply press the button on
the remote control(s) and make sure that the
RAD light flashes to confirm the input.
Press and release the “REMOTE”
button. The red RAD LED light
should come on.
When you have finished programming all of the
remote controls, wait for about 10 seconds until
the RAD LED light goes out. The remote con-
trols are now programmed and ready to use.
Press the button on the transmitter (remote con-
trol) you wish to program. The RAD LED light
on the Star 24 control board should flash rapidly
to confirm that it has recognized the transmitter
input.
NOTE:
You can program up to 200
buttons on remote controls
at one time using this pro-
cedure
ADJUSTABLE SLOW DOWN LEARNING PROCEDURE
The jet operator can be programmed to slow down at any point during the opening and closing process. This is especially useful when you
are using the operator on large gates or in compact installation. Complete the normal programming procedure for the jet operator first to make
sure the operator is operating correctly and that the open and close stops are set properly.
use the following procedure to reprogram the operator for adjustable slow down.
Step 1
Step 4
Step 7
Step 2
Step 3
Step 6
Locate the “PROGRAM” button on the
Star 24 control board. The red LED lights;
PH and STP should be on.
Immediately press the “REMOTE” button on the Star
24 control board. The yellow SET LED light will now
stop flashing and the jet will begin its learning pro-
cedure. The gate will open for 5 seconds and then
close. The yellow SET LED light will remain on and
the operator is now standing by for a command input.
With the gate open use the same procedure to set the slow down point for
closing the gate: Press the PROGRAM or remote control button to begin
closing and then press it again at the point you want the gate to slow down.
When the gate is completely closed the yellow SET LED light will go out
and the programming is complete.
Press and hold the Program button for
about 2 seconds. The red LED lights
will go out. Release the Program button
when the red LED’s go out.
Step 5
Using either the “PROGRAM” but-
ton on the Star 24 control board or a
programmed remote control, press
the button to initiate a command.
The gate will now begin to open.
The red LED lights will come back on and
the yellow SET LED light will now begin
to flash.
When the gate reaches the
point where you wish the slow
down to begin, press the PRO-
GRAM or remote control button
again and the gate will slow
down.
NOTE:
In a double gate, master/ slave configuration: The
PROGRAM button is used to set the slow down point
for the first gate and the REMOTE button is used to
set the slow down points for the second gate.