Rangemaster 110 Ceramic User Manual - page 24
24
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Servicing Notes
Disconnect from electricity supply before
commencing servicing, particularly before
removing any of the following: control panel,
side panels, ceramic hob, or any of the electrical
components or cover boxes. Before electrical
reconnection check that the appliance is
electrically safe.
1. To Remove a Side Panel
Disconnect from electricity supply.
Pull the cooker forward.
Pull off the push fi t control panel end caps at each end
and remove the end fi xing screws under the end cap.
Remove the retaining screws for each panel (1 at the
front and 2 at the rear). The lower front retaining screws
(one each side) are situated beneath the lower edge at
the front corners of the side panels
Reassemble in reverse order.
2. To Lift up the Ceramic Hob
Pull the cooker forward.
Pull off the push fi t control panel end caps at each end
and remove the end fi xing screws under the end cap.
Remove the lower front retaining screws (one each side)
situated beneath the lower edge at the front corners of
the side panels.
Swing the side panels to gain access to the hob fi xing
screws (1 each side) at the top front of the side uprights.
Remove these screws.
Caution
The ceramic hob material is much more
sensitive to scratches on the underside than
the top.
Lift up the ceramic hob at the front and prop in position
with a non-metallic prop.
Take care not to touch or scratch the
underside of the ceramic as this will weaken
the material and cause the top to shatter.
3. To replace a hob element.
Lift up the ceramic hob see 2. The elements are now
accessible.
4 To Remove the Control Panel
Disconnect from electricity supply.
Lift up the front of the ceramic hob – see 2. Remove the
control panel top scews.
Pull off all the control knobs. Open the grill and oven
doors and remove the control panel fi xing screws
underneath the control panel. The screws directly below
the clock are for the clock fi xing bracket - don’t remove
them at this stage.
Lift the control panel, pull forward and disconnect the
wiring from the rear.
Reassemble in reverse order. When replacing leads
refer to the wiring diagram. Check operation of timer.
5. To Remove Oven Light Switch
Remove control panel (see 4).
NB The old switch may be destroyed during removal.
Remove switch button and old switch from its bezel by
gripping the switch body behind the control panel and
twisting sharply.
The switch bezel can then be removed by folding back
its locking wings and pushing forward. Fit the new bezel
to the control panel by fi rst lining up the raised key on its
body with the cut-out in the control panel and pushing it
in from the front. Assemble the new switch to the bezel
by lining up the key sections and pushing home. Fit the
new button by pushing in from the front.
Replace control panel in reverse order and test for
correct operation.
6. To
Remove
Electronic
Timer
Disconnect from electricity supply.
Pull off the timer control buttons and remove the control
panel (See 4). Remove the timer/mounting bracket
assembly from the control panel by removing the two
fi xing screws. Remove the timer from its mounting
bracket by depressing the plastic lugs on the timer case,
at the same time pulling the unit forward.
Reassemble in reverse order. When replacing leads
refer to the wiring diagram. Check operation of timer.
7. To
Remove
a
Thermostat
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Open appropriate oven door and remove
oven furniture.
RH oven
Remove thermostat phial cover (2 screws).
Unclip the thermostat phial from the clips in
the oven back.
LH oven
Pull cooker forward to gain access to the
cover box at the rear of the cooker. Remove
the screws securing the cover and lift clear.
Feed the thermostat capillary out of the oven.
Disconnect wiring from thermostat. Remove 2 screws