Summary of Cruizer II
Page 1
Operation guide accuboom™ or accurow™ for cruizer ii consoles.
Page 2: Table of Contents
1 table of contents table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 accuboom setup . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3: Introduction
2 introduction the raven accuboom and accurow systems may be used with the cruizer ii guidance console to provide automatic boom or planter section control features. Note: prior to using the accuboom or accurow feature with the cruizer ii console, the supporting machine specific hardware components ...
Page 4: Accuboom Setup
3 accuboom setup sprayer section setup note: the sections icon is only displayed in the tools menu if an accuboom or accurow node is connected to the cruizer ii canbus. The section configuration uses the programmed antenna fore/aft and left/right values to determine the relative location of each sec...
Page 5: Sprayer Setup
4 sprayer setup from the home screen, touch tools , and select the sprayer icon in the vehicle menu to access the sprayer screen. This screen allows the operator to customize the response of the accuboom system for the specific flow control hardware installed on the sprayer. Note: touch the home ico...
Page 6: Controller Setup Screen
5 controller setup screen touch the spray control setup icon in the lower, left corner of the sprayer setup screen to view the controller setup screen. The controller setup screen allows the operator to select the accuboom control parameters for product application. Under most conditions, these sett...
Page 7: Accurow Setup
6 accurow setup planter row & section setup note: the sections icon is only displayed in the tools menu if an accuboom or accurow node is connected to the cruizer ii canbus. The section configuration uses the programmed antenna fore/aft and left/right values to determine the relative location of eac...
Page 8: Planter Setup Screen
7 6. Use the number of sections slider to set the number of planter sections (max. Of 16) on the implement. Cruizer ii automatically divides the implement width (displayed in the lower, left information area) by the number of sections entered. Note: touch the implement value in the lower, left infor...
Page 9: Controller Setup Screen
8 accurow override the accurow override allows the operator to momentarily override the automatic planter section control feature and force all sections on. This may be useful to ensure complete seed coverage in point rows or when accelerating from a complete stop. Enable the accurow override featur...
Page 10: Guidance Screen
9 guidance screen once the accuboom or accurow feature is configured, the cruizer ii console may be used to display boom or planter sections status during an active guidance session. Note: refer to the cruizer ii operation guide for instructions on starting a guidance session. Section status: • gree...
Page 11: Field Review Mode
1 0 field review mode zones or boundaries recorded with the accuboom or accurow features may be displayed on the field review screen. From the cruizer ii guidance screen, touch menu and field review to switch to field review mode from the guidance display. Modes of operation when used with the cruiz...
Page 12: Zone Mapping Mode
1 1 zone mapping mode accuboom or accurow zones may be created around areas inside which product application should be avoided. Areas such as waterways, well heads, tree lines, etc may be marked as no spray zones for automatic section shutoff features. With a no spray/plant boundary completed, the a...
Page 13
1 2 2. The operator will be prompted to set the marker location for the boundary to be created. The marker location is the point on the guidance width which the cruizer ii will map as the boundary of the feature. 3. Select the center, left end, or right end of the configured guidance width and touch...
Page 14: Reference of Mapping Icons
1 3 reference of mapping icons the icons in the following sections will be displayed within the boundary mapping menu. Some tools or features used with boundaries on the cruizer ii console are only available while a boundary is recorded or after recording of a feature boundary is completed. Field bo...
Page 15
1 4 accurow select the reset no spray zone icon to clear the current boundary path being recorded. Select the delete no spray zone boundary icon to erase a completed no spray zone boundary from the current guidance session. Touch the no spray boundary tools icon to display the set marker location sc...
Page 16
Notice: this document and the information provided are the property of raven industries, inc. And may only be used as authorized by raven industries, inc. All rights reserved under copyright laws. Raven industries toll free (u.S. And canada): (800)-243-5435 applied technology division or outside the...