Installation manual safera siro r-line stove guard power control units: pcu3 pcu3-w pcu5.1-u pcu5.1-p 20812 v4.5.0 eng siro r-line.
3 2 1. Preparations check the product and the contents of the package before installation: • sensor unit with mounting bracket Ⓐ • power supply Ⓓ • power control unit Ⓒ • user and installation guides • declaration of conformity ѥ warning please contact your vendor if you notice anything unusual abou...
5 4 install the cental unit Ⓐ on the wall above the cooktop and follow these dimensions: ⚐ attention the sensor unit Ⓐ is plugged into the wall socket with its own power supply Ⓓ. Min 8 mm min 5 mm 200 mm 1 2 ”klik” 3 ”klik” 4 5 cooker width installation height max. 60 cm 45 - 75 cm 60 - 90 cm 60 - ...
7 6 install the power control unit according to the following instructions. Installation - step 2/6 mount the power control unit Ⓒ. Pcu5.1-u fixed 1-phase connection. See pages 12-13. Pcu3-w perilex-connectors. See pages 10-11. Pcu3 fixed 3-phase connection. See pages 8-9. Pcu5.1-p 3-pin plug. See p...
9 8 ѥ warning make sure that there is no power supply to the cooker and the oven by removing their fuses. Also ensure that the cooker is swit- ched off. Out-wires are always energized when the power control unit is connected to the electrical network. If a wire is loose, it must be properly covered....
11 10 ѥ warning make sure that there is no power supply to the cooker and the oven by removing their fuses. Also ensure that the cooker is swit- ched off. Out-wires are always energized when the power control unit is connected to the electrical network. If a wire is loose, it must be properly covere...
13 12 ѥ warning make sure that there is no power supply to the cooker and the oven by removing their fuses. Also ensure that the cooker is swit- ched off. Out-wires are always energized when the power control unit is connected to the electrical network. If a wire is loose, it must be properly covere...
15 14 59-79 mm 73 mm 60 mm 68-80 mm ѥ warning make sure that there is no power supply to the cooker and the oven by removing their fuses. Also ensure that the cooker is swit- ched off. Out-wires are always energized when the power control unit is connected to the electrical network. If a wire is loo...
17 16 connect the power supply Ⓓ to the sensor unit Ⓐ: indicator light panels ❽ are lit in purple. Put back the fuses for the cooker and the oven. The power control unit Ⓒ will now contact the sensor unit Ⓐ which gives a sound signal (•••). Press the adjustment mode button ❼: indicator light panels ...
19 18 adjust the alarm limit according to the reference table above. The default alarm limit is 6. First, go to the adjustment mode: 2 check the closest recommended alarm limit from the refe- rence table on the right. The range is 1-12: 1 = reacts fastest 12 = reacts slowest then, adjust the alarm l...
21 20 check the working order of the appliance and fill in the installation checklist: ≅ all the burners of the cooker cause a child proof lock alarm. ≅ the oven (if connected) causes the child proof lock alarm. The sound signal is lower than the signal from the cooker child proof lock. ≅ the child ...
23 22 4. Installing the water leakage sensor (optional) stove guard can be equipped with max. Four safera water leakage sensors. The sensors are placed in the typical leakage areas, e.G. Under the dishwasher or sink. Attach the sensors Ⓕ in place. 1 ѧ hint if the sensor is left wet, the appliance wi...
24.
