Sailor C4951WP Operating And Installation Instructions - page 23
19
7
Installation – Control Unit
7.1
Mounting possibilities
Mounting is carried out by first fixing the backplate, after which the
Control Unit can simply be slid over and clicked into place. There is
a template on page 31 to help you mount the unit.
To avoid theft, the control unit can be removed when leaving the boat
or during the off-season simply by pressing the spring and lifting it
off the backplate
7.2
Power supply
The Control Unit is supplied with +12V DC from the SPARC-bus
interface.
If there is a short circuit or fire, it is important that your VHF remain
operational. We therefore recommend that the power cable be
connected directly to the ship’s battery.
7.3
Control unit connection –
Leisure class D VHF
Remote control units can be connected in two ways
1.
Directly between the transceiver and the control unit .
2.
Via a SPARC-bus splitter box or WP SPARC-bus connection
box (optional, not included).
Both control units with or without DSC can be connected.
Remote speakers may be connected to remote Control Units via a
splitter box , or a WP SPARC-bus connection box.
Not more than four Control Units can be simultaneously connected
to a transceiver without DSC and not more than seven with DSC.
7.4
Connecting the transceiver /
Control Unit
38050
Transceiver
X1
Indoor
7.5
Connecting the transceiver /
splitter box / indoor and
waterproof Control Unit
38052A
Transceiver
56.114
Indoor
Outdoor
X1
Factory delivered
WP SPARC-Bus connection
(Optional)
TX 1W
US
CALL
ALARM
7.6
Control Unit connection –
Commercial class A VHF
Remote control units can be connected in two ways:
1.
Directly between the transceiver and the control unit .
2.
Via a SPARC-bus splitter box or WP SPARC-bus connection box.
Both control units with or without DSC can be connected.
Remote speakers may be connected to remote Control Units, to a
splitter box , or via a WP SPARC-bus connection box.
Not more than seven handsets can be simultaneously connected to
the transceiver with DSC. Always connect the local Control unit to
the transceiver. The DSC class of intelligent Control Unit is ‘D’ even
if the radio is Class A.
38051A
56.114
Transceiver
Indoor
Outdoor
Factory delivered
US
TX 1W
CALL
ALARM
SPARC-BUS
HANDSET
PRINTER
OPTION
Tx
Rx
/
12V DC
7.7
Loudspeaker connection
When one or more control units are connected to the VHF system,
two of them can be set up to use the transceiver’s two loudspeaker
outputs to drive external speakers.
To link a loudspeaker to a control unit:
1.
Lift the handset.
2.
Press Shift, Func to display TELEPHONY.
3.
Press down arrow twice to display GENERAL.
4.
Press right arrow once to display ILLUMIN.
5.
Press down arrow twice to display SOUND.
6.
Press right arrow once to display EARPIECE.
7.
Press up arrow once to display LOUDSPEAK.
8.
Press right arrow three times to display EXTSPK.
9.
Use up and down arrows to set external speaker to 1 or 2, as
required.
10. Press right arrow to complete selection. If you make a mistake
at any step, simply press 16 to return to the beginning. It is not
possible to step backwards through the menu sequence.
Loudspeaker signals are available in the SPARC-bus cabling, and a
loudspeaker can be connected to the system rest, in the SPARC-bus
splitter box, or in the WP SPARC-bus connection box. Connect the
loudspeaker cables to SPARC-bus signals (LS_1+ and LS1_!) or
(LS_2+ and LS_2!) depending on which speaker selection is made
by the control unit(s).
Installation - Control Unit
0310