1. DL manuals
  2. Sensus
  3. Measuring Instruments
  4. PolluStat E
  5. Installation And Operating Instructions Manual

Sensus PolluStat E Installation And Operating Instructions Manual

Manual is about: Heating / Cooling meter

Summary of PolluStat E

  • Page 1

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 1 pollustat e installation and operating instructions.

  • Page 2

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 2 the ultrasonic meter pollustat e is suitable for the measurement of energy consumption in heating or cooling plants filled with the energy carrier liquid water. These installation and operati...

  • Page 3

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 3 mains-operated instruments: the supply to mains-operated instruments must be fused at 6 a. Only specially trained and authorized personnel are permitted to carry out the connection. Moreover ...

  • Page 4

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 4 4.1 flow sensor applicable standards: en 1434-6 standard installation of the flow sensor is in the heating return pipe i.E. The colder line. If the flow sensor is to be installed in the heati...

  • Page 5

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 5 4.2 installation of temperature sensors pollustat e is operated with separately approved and paired temperature sensors type pt 100 or pt 500. The applicable type is specified on the integrat...

  • Page 6

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 6 supply pipe temperature sensor (warmer line): connection type terminals two-wire connection 5, 6 four-wire connection 5, 6 and 1, 2 screening, if any return pipe temperature sensor (colder li...

  • Page 7

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 7 5. Display options the different display options of pollustat e are divided into six menus. Depending on the type of the meter and the display masking respectively, some display items, which ...

  • Page 8

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 8 temperature difference * customer specific number * primary m-bus address (factory setting: 0) * secondary m-bus address (factory setting: meter serial number) * 5.2 target day menu all displ...

  • Page 9

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 9 hours of error condition * hours of mains supply failure * (only for mains supplied meters) return to month selection (depress for 2 seconds) 5.4 service menu each display item is marked with...

  • Page 10

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 10 5.5 control menu for tariff purposes each display item is marked with the letters „ctrl“. The settings for the tariff functions can be controlled here. Set averaging interval for flow rate a...

  • Page 11

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 11 6. Functional test, sealing having opened the shut-off valves, test the installed units for leaks. For checking purposes the current values of flow rate, heating resp. Cooling power as well ...

  • Page 12

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 12 protocol corresponds to the m-bus protocol, and the meter can be read out via a minireader or using dokom mobile. 8.3 m-bus plug-in module acc. To en 13757-3 order number: 68504020 this plug...

  • Page 13

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 13 fig. 11: mounting modules the plug-in units mounted in the left and right guidance from a white plastic plug. The pins must not be bent and slide easily into the appropriate contact sockets....

  • Page 14

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 14 declaration of mid conformity.

  • Page 15

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 15 space for extra notes:.

  • Page 16

    Heating / cooling meter pollustat e installation and operating instructions m h 4110 int pollustat e, page 16 material number: 28504907 edition: 004-11.2016 subject to change without notice sensus gmbh ludwigshafen industriestraße 16 d-67063 ludwigshafen telefon: + 49 (0) 621 6904-1113 fax: + 49 (0)...