- DL manuals
- Svantek
- Measuring Instruments
- SV 102
- Quick Start Manual
Svantek SV 102 Quick Start Manual
Summary of SV 102
Page 1
Sv 102 dual channel acoustic dosimeter quick start guide (draft) www.Svantek.Com.
Page 2
Sv 102 user guide © svantek 1 table of contents table of contents table of contents table of contents introduction..................................................... 2 control push-buttons ...................................... 3 before you turn instrument on........................ 3 turning inst...
Page 3
Sv 102 user guide © svantek 2 introduction introduction introduction introduction this quick start guide will help you to get started with sv102 instrument. The sv 102 device is a dual cannel dosimeter which enables performing binaural dose measurements and the 1/1 octave analysis simultaneously. Sv...
Page 4
Sv 102 user guide © svantek 3 control push control push control push control push- - - -buttons buttons buttons buttons on/off (if held); enter; escape (if pressed with ) shift - second (“red”) functionality of other push-buttons; switching on the backlight (if held) left + escape right + menu + up ...
Page 5
Sv 102 user guide © svantek 4 this message appears when the calibrator factor stored in teds memory of microphone doesn’t match calibrator factor in the instrument’s memory. It means that the microphone hasn’t been calibrated in the channel it is connected to or it hasn’t been used with this instrum...
Page 6
Sv 102 user guide © svantek 5 battery check battery check battery check battery check observe the battery icon in the instrument’s icon status line or go to menu ( + ) > display > battery and check the state of the power source. If it is too low, exchange the batteries. Press + to exit. Exchanging b...
Page 7
Sv 102 user guide © svantek 6 measurement setup measurement setup measurement setup measurement setup go to menu ( + ) > function and select proper mode and measurement function. Go to menu ( + ) > input > measurement setup and configure (using and push-buttons) following parameters: start delay - p...
Page 8
Sv 102 user guide © svantek 7 if logger is switched on, go to menu > input > left (right) channel > profile 1 (2, 3) and select results to be logged: peak, max, min or/and rms. Go to menu ( + ) > input > profile 1 (2, 3) and select detector time constant (fast/slow/impulse). Availability of filter s...
Page 9
Sv 102 user guide © svantek 8 depending on the function being used, adjust other necessary settings i.E. In: dosimeter setup window (menu > input > dosimeter setup) spectrum window (menu > input > spectrum) it is also possible to load one of standard setups (osha, msha, dod, acgih, iso 85, iso 95) b...
Page 10
Sv 102 user guide © svantek 9 press + to start the calibration measurement when the calibration measurement is done, it shows cal. Result e.G. Leq=114.22 db if you need to restart the calibration, press + again press to accept the calibration result press to confirm calibration factor and to store i...
Page 11
Sv 102 user guide © svantek 10 making a simple measurement & using display options making a simple measurement & using display options making a simple measurement & using display options making a simple measurement & using display options press + push-buttons till you see main view. If the logger fu...
Page 12
Sv 102 user guide © svantek 11.
Page 13
Sv 102 user guide © svantek 12 saving measurement results saving measurement results saving measurement results saving measurement results two types of files for storing measurement results are available - results files and logger files. Logger files are saved automatically to save results, the meas...
Page 14
Sv 102 user guide © svantek 13 loading measurement results loading measurement results loading measurement results loading measurement results to view saved measurement results, go to menu ( + ) > file > load, select file you wish to load and press . Deleting measurement results deleting measurement...