Tascam CC-222MK Owner's Manual - 6- After Recording
TASCAM CC-222MKIII
Erasing tracks
It is possible to erase the last recorded track, the last
two recorded tracks, the last three recorded tracks, etc.
It is not, however, possible to erase tracks in the “mid-
dle” of the disc.
1 Withthediscloaded,andtheunitinstopmode,
pressthe
ERASE
key.
2 Ifthedisplaydoesnotshow
ERASE XX-XX?
,
where
XX-XX
isthenumberofthelasttrack
recordedonthedisc,turnthe
MULTI DIAL
oruse
the
SKIP
keysuntilitisdisplayed.
3 Turnthe
MULTI DIAL
orusethe
SKIP
keysto
changethenumberofthefirsttracktobeerased.
Thehighestvaluethatthisnumbercantakeis
thelasttrackrecorded(forexample,if17tracks
havebeenrecordedonthedisc,17-17meansthat
thelasttrackonly,number17,willbeerased).
Thelowestvaluethatthisnumbercantakeis2
(ifthisnumberwas1,thewholediscwouldbe
erased,asdescribedbelow).Ifyoudonotwant
toproceedwiththeeraseoperation,pressthe
ERASE
keyor
STOP
key.
NOTE
If only one track has been recorded on the disc,
only the “erase disc” option (see “Erasing a whole
disc”on page 28) is available.
4 Whentherangeoftrackstobeerasedhasbeen
selected,pressthe
MULTI DIAL
orthe
ENTER
key.
NOTE
This operation cannot be undone. If you are going
to erase a track or tracks, make sure that they are
recordings that you really want to erase!
Iftheeraseoperationhasbeenselected,theword
ERASE
flashesonthedisplay,andthetimerstarts
countingdown.
Attheendofthecountdownperiod,theword
Complete
appearsbrieflyonthedisplay,andthe
displayreturnstothetrack/timedisplay.
Erasing a whole disc
When you want to erase a whole disc (all the tracks on a
disc), follow the procedure below:
1 Withthediscloaded,andtheunitinstopmode,
pressthe
ERASE
key.
2 Turnthe
MULTI DIAL
orusethe
SKIP
keysuntil
thedisplayshows
ERASE DISC?
.
Ifyoudonotwanttoproceedwiththeeraseop-
eration,pressthe
ERASE
keyor
STOP
key.
3 Toerasethecontentsofthedisc,pressthe
MULTI
DIAL
orthe
ENTER
key.
NOTE
This operation cannot be undone. If you are going
to erase a disc, make sure that it contains only
recordings that you really want to erase!
Iftheeraseoperationhasbeenselected,theword
ERASE
flashesonthedisplay,andthetimerstarts
countingdownatimevalueshownonthedis-
play.
Attheendofthecountdownperiod,theword
Complete
appearsbrieflyonthedisplay,andthe
displayreturnstothetrack/timedisplay.
Refreshing a disc
If a CD-RW disc has been corrupted at any point (e.g.
power has been cut off in the middle of a finalize opera-
tion, etc.), or has been used in a computer or another
piece of equipment that makes it unreadable, it is pos-
sible to “refresh” the disc to make it usable again.
1 Withthediscloaded,andtheunitinstopmode,
pressthe
ERASE
key.
2 Turnthe
MULTI DIAL
orusethe
SKIP
keysuntil
thedisplayshows
DISC REFRESH?
.
3 Torefreshthedisc,pressthe
MULTI DIAL
orthe
ENTER
key.
Ifyoudonotwanttoproceedwiththerefresh
operation,pressthe
ERASE
keyor
STOP
key.
NOTE
This operation cannot be undone. If you are going
to refresh a disc, make sure that it contains only
recordings that you really want to erase!
Iftherefreshoperationhasbeenselected,the
words
ERASE XX:XX
areshownonthedisplay,
andthetimerstartscountingdown.
Attheendofthecountdownperiod,theword
Completeappearsbrieflyonthedisplay,and
thedisplayreturnstothetrack/timedisplay(of
course,therearenotracks,andthediscisatthe
start,withthetotaltimeofthediscavailablefor
recording).