1. DL manuals
  2. U-Line
  3. Refrigerator
  4. CLR2060
  5. User Manual

U-Line CLR2060 User Manual

Summary of CLR2060

  • Page 1

    P . O . B o x 2 4 5 0 4 0 milwaukee, wi 53224-9540 p h o n e : 4 1 4 . 3 5 4 . 0 3 0 0 f a x : 4 1 4 . 3 5 4 . 7 9 0 5 w w w . U - l i n e . C o m p r i n t e d i n u . S . A . P / n 3 0 - 1 0 0 0 9 É c h e l o n ™ u s e r m a n u a l.

  • Page 2

    U-line corporation limited warranty u-line corporation warrants each u-line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass...

  • Page 3: Introduction

    Introduction congratulations on your purchase of a u-line clr2060 ice maker. A pioneer in the field for nearly 40 years, u-line is the world’s number one manufacturer of built-in, under-counter ice making and specialty refrigeration products. U-line dedicates 100% of its research and development to ...

  • Page 4: Table of Contents

    If you do not return your warranty registration card, u-line will use the date of sale to the u-line distributor as the first date of warranty for your new ice maker. Please also record the purchase date of your u-line unit and your dealer’s name, address and telephone number. Model number: ________...

  • Page 5: Safety Precautions

    3 safety precautions do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a danger, warning or caution based on the risk type. Definitions danger means that failure to follow this safety stateme...

  • Page 6: User’S Manual

    4 user’s manual general precautions risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so that children may not easily climb inside. • never attempt to repair or perform maintenance on the unit until the electricity has bee...

  • Page 7: Installation Dimensions

    5 installation dimensions figure 1 drain installation please read all instructions completely before attempting to install or operate the unit. All ice makers require a con- nection to the water supply and improper hook-up can result in substantial property damage! All water and drain connections mu...

  • Page 8: User’S Manual

    6 user’s manual follow these guidelines when installing drain lines to prevent water from flowing back into the ice maker storage bin and/or potentially flowing onto the floor causing water damage: gravity drain • drain lines must have a 5/8 inch inside diameter. • drain lines must have a 1 inch dro...

  • Page 9: Warning

    3. Remove 12 screws and back panel. 4. Check that the clamps and hose connections are tight at the fol- lowing areas: • discharge tube (a) • drain tube (b) • vent tube (c) 5. Place a suitable container beneath the pump’s discharge tube. (the bucket must be able to hold a minimum of one gallon.) back...

  • Page 10: Connecting A Drain Pump

    Connecting a drain pump if a gravity drain connection is not available, and you have not pur- chased the clr2060 with factory installed pump, we strongly rec- ommend the use of the u-line p60 drain pump. The u-line p60 drain pump is available through your dealer, or direct from u-line with com- plet...

  • Page 11: Danger

    Electrocution hazard! Electrical grounding required. This appliance is equipped with a three prong (grounding) polarized plug for your protection against possible shock hazards. • never remove the round grounding prong from the plug. • never use a two-prong grounding adapter. • never use an extensio...

  • Page 12: Note

    Note stainless steel models require a minimum of 2-1/2" door clearance. 6. Install and connect the water supply line. See connecting the water supply for installation requirements. 7. Position the unit to allow free air flow through the front grille (see figure 3). Figure 3 8. Be sure to install ant...

  • Page 13: Connecting The Water Supply

    11 connecting the water supply 1. Remove grille from front of the unit (see figure 4). Refer to condenser cleaning. 2. Remove the back panel to ease water line connection. Ul203a grille panel screw screw screws i c e o f f c l n figure 4 figure 5 ul401 i c e o f f c l n 3. Install the 1/4 inch coppe...

  • Page 14: User’S Manual

    4. Locate the compression fit- ting and ferrule packed in the unit. Slide the compression fitting and ferrule over the 1/4 inch water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see figure 6). Figure 6 5. Carefully ...

  • Page 15: Note

    Note after completing the installation, turn on the water and recheck water and drain connection for leaks. Apply addi- tional tightening if needed. Do not use thread sealing com- pound or tape. Note route the water supply line through the clip on the sidewall of the unit in such a way as to prevent...

  • Page 16: User’S Manual

    14 user’s manual 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. Reversing the door all u-line units (except stainless steel models) may be left or right hand opening. The door opening is easily reversed by moving the hinge hard- ware to the opposi...

  • Page 17

    15 1. Remove top hinge screw pin (7/64" allen wrench) from cabinet (see figure 13). Remove door by tilting forward and lifting off bottom hinge pin. Figure 13 2. Remove plastic screw plugs (3 each, top and bottom) from new hinge location. Do not discard (see figure 14). Figure 14 3. Remove top hinge...

  • Page 18: User’S Manual

    5. Remove existing bottom hinge (3 screws) and remount on opposite side top. Remove hinge screw pin. 6. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see figure 17). Figure 17 7. Holding door upright with top of door tilted forward, pl...

  • Page 19: Custom Door Panels

    Custom door panels two types of custom door panels can be installed on your u-line unit to harmonize with or accent the surrounding decor. Full overlay door panel a full overlay door panel completely covers the door frame and handle to give a built-in appearance. See your u-line dealer for the optio...

  • Page 20: Warning

    Install the insert as follows: insert edges may be sharp! Use care when installing. 1. Remove top hinge screw pin (7/64" allen wrench, see figure 20). Remove door by tilting forward and lifting off bottom hinge pin. 2. Remove two outside screws hold- ing door handle. Slightly separate door handle fr...

  • Page 21: Built-In Installation

    Built-in installation your u-line product has been designed for either free-standing or built- in installation. When built-in, your u-line product does not require addi- tional air space for top, sides or rear. However, the front grille must not be obstructed. Do not install unit behind closed doors...

  • Page 22: Initial Start-Up

    Initial start-up once installation and leveling is complete, the unit is ready for initial start-up and operation. Your unit is shipped in the off position, how- ever, you may turn it on/off using the cycle selector switch located in the grille (see figure 24). Figure 24 1. Plug the appliance cord i...

  • Page 23: Normal Operation

    Normal operation the ice maker is designed to make clear ice from most water sources on a consistent basis. Water is constantly circulated over the evapo- rator assembly. As the water freezes, gravity causes any sediment to drop into the water trough and not become imbedded in the ice. This gives a ...

  • Page 24: Maintenance

    Maintenance periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, the unit is used outdoors, or other special considerations. Exterior c...

  • Page 25: Warning

    • do not use solvent cleaning agents or abrasives on the interior. These cleansers may transmit taste to the ice cubes, or damage or discolor the interior. • do not use any cleaner inside the ice maker compart- ment other than u-line ice machine cleaner. Other cleaners may affect ice quality or dama...

  • Page 26: Caution

    Do not touch the condenser fins. The condenser fins are sharp and can be easily damaged. Do not use any type of cleaner on the condenser unit. 3. Clean the condenser coil using a brush or vacuum cleaner. Do not touch. 4. Position the grille to align the screw holes with the cabinet. 5. Insert the gr...

  • Page 27: Caution

    Ice machine cleaner is used to remove lime scale and other mineral deposits. Refer to the following steps for mineral deposit removal. Never use anything to force ice from the evaporator. Damage may result. 1. Set the cycle selector switch to off and allow the ice to melt off of the evaporator. 2. R...

  • Page 28: User’S Manual

    9. When the self-cleaning process stops (approximately 45 minutes) it may be desirable to clean the storage bin at this time (see interior cleaning). 10. Move the cycle selector switch to the ice position to resume ice production. Inlet screen cleaning — every year the solenoid valve inlet screen mu...

  • Page 29: Storage, Vacation and Moving

    Storage, vacation and moving if the unit is to be stored, moved or not used for extended periods, it will be necessary to drain the system of water. Electrical shock hazard. Disconnect power before servicing. Before operating replace all panels. Failure to do so can result in death or electrical sho...

  • Page 30: User’S Manual

    28 user’s manual 7. Reconnect inlet and outlet lines to the water valve. 8. Replace front access panel. 9. Replace grille. 10. Drain water from the water trough and drain line by removing the overflow tube (see figure 27). 11. Clean the ice maker and storage bin before next use. 12. Prop door open t...

  • Page 31: Troubleshooting

    29 troubleshooting before calling for service if the unit appears to be malfunctioning, read through normal oper- ation first. If the problem persists, check the troubleshooting guide. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem could...

  • Page 32: User’S Manual

    Problem possible cause remedy unit runs but scale and mineral clean unit. See produces very buildup in unit. Maintenance. Little ice. Inadequate airflow at remove items blocking (continued) the front of the unit. Airflow. Ice is slow to ice-making system run unit through release or does is dirty. Au...

  • Page 33: If Service Is Required

    31 problem possible cause remedy water leaking supply line leaking. Check to see that water from under the inlet line is attached to unit. Inlet valve properly. See connecting the water supply. Fill tube leaking. Check connection at water valve outlet. Bin drain leaking. Check integrity of bin drain...

  • Page 34: Notes

    Notes ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ___________________________________ ______...

  • Page 35

    U-line corporation limited warranty u-line corporation warrants each u-line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass...

  • Page 36: É C H E L O N

    P . O . B o x 2 4 5 0 4 0 milwaukee, wi 53224-9540 p h o n e : 4 1 4 . 3 5 4 . 0 3 0 0 f a x : 4 1 4 . 3 5 4 . 7 9 0 5 w w w . U - l i n e . C o m p r i n t e d i n u . S . A . P / n 3 0 - 1 0 0 0 9 É c h e l o n ™ u s e r m a n u a l.