Www.U-lineservice.Com phone (414) 354-0300 • fax (414) 354-7905 service & parts tech lines phone (800) 779-2547 • fax (414) 354-5696 onlineservice@u-line.Com ©2006 u-line corporation 08/2006 clr2160 — clear ice maker installation guide.
Clr2160 — clear ice maker www.U-lineservice.Com 2 08/2006 contents exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 cut-out dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 product dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 d...
Clr2160 — clear ice maker 08/2006 3 www.U-lineservice.Com general precautions use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: warning shock hazard — electrical grounding required. • keep the unit unplugged throughou...
Clr2160 — clear ice maker www.U-lineservice.Com 4 08/2006 after all the protective coating has been removed from the unit/door, clean all stainless steel surfaces with claire stainless steel polish and cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do not u...
Clr2160 — clear ice maker 08/2006 5 www.U-lineservice.Com product dimensions please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets (see figure 45 on page 17). Door swing/clearances information black and white units have...
Clr2160 — clear ice maker www.U-lineservice.Com 6 08/2006 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see figure 8). 5. Remove existing bottom hinge (3 screws) and remount on opposite side top. Remove hinge screw pin. 6. Remove t...
Clr2160 — clear ice maker 08/2006 7 www.U-lineservice.Com side-by-side installation instructions for a complete refreshment center, install your clr2160 clear ice maker beside a u-line refrigerator, combo, or wine captain model (see figure 11 for typical cut-out). Note that each side-by-side install...
Clr2160 — clear ice maker www.U-lineservice.Com 8 08/2006 2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see figure 13). This may take some force. 3. Remove two outside screws holding door handle. Slightly separate door handle...
Clr2160 — clear ice maker 08/2006 9 www.U-lineservice.Com 2. Create a relief (figure 15) for pivot plate by cutting notch in top corner of overlay panel. Refer to figure 16 for exact specifications. Route notch in top corner of overlay panel as shown (see top and side views). Top of notch is entire ...
Clr2160 — clear ice maker www.U-lineservice.Com 10 08/2006 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in figure 21. The spacers allow the original door panel to slide back i...
Clr2160 — clear ice maker 08/2006 11 www.U-lineservice.Com 4. Attach top pivot plate to door handle, on side where hinges will be. Use the two #8-32 x 1/2" flat head phillips screws (black) supplied with kit (see figure 24). 5. Starting at the corners and working toward the center, push the door gas...
Clr2160 — clear ice maker www.U-lineservice.Com 12 08/2006 checking door alignment the unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Important properly aligned, the door should be 1/8" below ...
Clr2160 — clear ice maker 08/2006 13 www.U-lineservice.Com caution plumbing installation must observe all state and local codes. All water and drain connections must be made by a licensed/qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or ha...
Clr2160 — clear ice maker www.U-lineservice.Com 14 08/2006 important before installing your u-line clr2160 with factory- installed u-line p60 pump, it is extremely important to check and test all hose connections at the drain pump. There is a possibility that hose connections may have loosened durin...
Clr2160 — clear ice maker 08/2006 15 www.U-lineservice.Com 5. Place a suitable container beneath the pump’s discharge tube. (the bucket must be able to hold a minimum of one gallon.) 6. Plug the ice maker power cord into a properly grounded, polarized electrical outlet. 7. Verify pump operation by p...
Clr2160 — clear ice maker www.U-lineservice.Com 16 08/2006 3. Carefully bend the water supply line into position and connect the line to the solenoid valve (see figure 40). Avoid kinking the water supply line. Important normal operation creates some vibration. A water supply line contacting cabinet ...
Clr2160 — clear ice maker 08/2006 17 www.U-lineservice.Com leveling information important it is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly. A unit that is not level can cause a reduction in ice rate, uneven sized cubes or water spilling into the...
Clr2160 — clear ice maker www.U-lineservice.Com 18 08/2006 installation of the clr2160 1. Open the water supply valve in the main water source. 2. Plug in the power cord. 3. Open the door and press the power icon (see figure 46, 1) on the display panel until off is displayed. Note: if the unit is no...
Clr2160 — clear ice maker 08/2006 19 www.U-lineservice.Com initial start-up once installation and leveling is complete, the unit is ready for initial start-up and operation. The display panel is located inside the unit, on the top (see figure 46). 1. Open the door and remove the cover in front of th...
?2006 u-line corporation publication no. 30140e 08/2006 rev. B u-line corporation, located in milwaukee, wi, is a family operated manufacturer of built-in undercounter icemakers, combo ® icemaker/refrigerators, wine captain ® wine storage units, refrigerators, refrigerated drawers and refrigerator/f...
