© baxi heating u.K. Limited 2010. 5133239-02 model 820 electric heater fitted with one of the following fascia. Blenheim or seattle gc no. Ef-032-33 important: please keep your guide in a safe place for future reference. Installer and owner guide this guide is intended to help you install and care f...
Baxi heating u.K. Limited 2010. All rights reserved. No part of this publication may be reproduced in any material form (including photocopying), stored in any medium by electronic means (including in any retrieval system or database) or transmitted, in any form or by any means, whether electronic, ...
Safety first. Valor fires heaters are ce approved and designed to meet the appropriate british standards and safety marks. Quality and excellence. All valor fires heaters are manufactured to the highest standards of quality and excellence and are manufactured under a bs en iso 9001 quality system ac...
2. Safety this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety...
Caution: in order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. Important! This heater must be earthed. ...
3. Fitting the heater the installation of this heater requires a reasonable level of diy skills. Please read this guide thoroughly before commencing installation and if in doubt, seek help from a competent person. Important: before continuing with the installation of this heater please ensure that y...
4. Hold the bottom of the cable guide close to the heater then gently pull the cable guide away from the rectangular slot (see figure 1- item 3). Fitting the cable guide. When fitting the cable guide please remember that the wider part of the cable guide has to be fitted against the outer edge of th...
Heater fixing. All fixings supplied with the heater have been identified in figure 3. Page 8 installer and owner guide © baxi heating u.K. Limited 2010. Figure 3. Contents. Fascia not shown (items are not to scale) contents quantity (illustrations are not to scale) heater 1 wall plug 5 wood screw 4 ...
Fitting the control knob. The control knob is supplied separately with the accessory pack. Fit the control knob before continuing with the heater installation. To assemble the control knob to the control spindle, firstly line up the ‘d’ profile on the underside of the control knob to the ‘d’ profile...
Marked positions. Insert wall plugs into the drilled holes. 5. Place the heater so that the slotted holes are in line with the wall plugs in the fixing surface. 6. Screw and secure the heater with two wood screws (see figure 3). Method b - wire fix. This method of fixing needs a fireplace opening an...
9. At the back of the heater there will be a long piece and a short piece of wire coming through the two holes. Hold the short piece and give the long piece a gentle tug. This will secure the steel wire. Take the long piece and thread this through the eyescrew in the back of the fireplace opening (s...
Fitting the heater. 1. Locate the spacer frame and heater over the screw heads ensuring a tight fit. If the fit is loose, remove the spacer frame and heater from the wall. Tighten the wall screws slightly and reposition the spacer frame and heater. Fitting the light diffuser. 1. There is a light dif...
Seattle model. 1. With the fascia trim removed, unscrew and remove the two screws from the lower right hand side of the heater (see figure 13) then align the four holes in the firefront assembly with those on the heater (see figure 14). Secure with the two screws removed previously and two screws su...
4. Using the heater important safety never cover the heater or obstruct the openings at the base of the heater, this could cause overheating and consequent risk of fire. What are the three switches for? The heater is operated by three switches located below the hood on the left hand side of the heat...
5. Cleaning and maintaining the heater how do i clean my heater? The heater fascia and plastic parts need only to be wiped clean with a dry soft cloth, do not use polishes or abrasive materials. The seattle heater may have fingerprints on the fascia surface. These can be removed by applying a small ...
6. Warranty and service information for the customer standard warranty terms & conditions the warranty is for 12 months subject to contract. In the united kingdom servicing can be carried out either by a heateam service engineer or a suitably qualified person. You must register your heater with heat...
What this warranty does not cover repairs to heaters which haven’t been installed properly and as set out in this guide. Faults caused by inadequate supply of electricity. Reimbursement of any third party repair or replacement costs that we haven’t been told about or agreed with you in advance. Comp...
Page 18 installer and owner guide © baxi heating u.K. Limited 2010..
Page 19 installer and owner guide © baxi heating u.K. Limited 2010. Brand (please tick) baxi valor wonderfire other................. D d m m y y date of installation fascia name (block capitals) fascia code - can be found close to the information label (block capitals) figure 16 model 8 2 0 serial n...
© baxi heating u.K. Limited 2010..
