Power painter plus power painter max power painter pro owner’s manual read this manual for complete instructions 0312 • form no. 0525658e patent pending contents 2 important safety information 3 before you begin 4 features 5 cup mode setup 6 remote suction hoses setup 7 backpack kit setup 8 spray co...
English 2 safety safety important safety information read all safety information before operating the equipment. Save these instructions indicates a hazardous situation which, if not avoided, could result in death or serious injury. A) toreducetherisksoffireorexplosion,electricalshock and the injury...
English 3 safety safety before you begin: this page contains information that is necessary in order to operate the sprayer properly. Material preparation: • it is important to mix the material thoroughly before you begin. Do not shake the material to mix it. Always stir the material gently but thoro...
O a a1 a2 b e d l n m p a1 a2 a power painter max power painter plus power painter pro c d g g h h j-k i-k f a a1 a2 g f d c english 4 features start the spray gun you have purchased will have some or all of the features and accessories shown here. Refer to the graphic, right, and the chart, below. ...
English 5 cup mode setup start english recommended for small to medium jobs note: the cup will give you approximately 3-5 minutes of continuous spraying time depending upon the cup size. Important: avoid running the cup dry. An empty cup will allow air to become sucked into the sprayer, which leads ...
English 6 remote suction hose setup (optional) start 1. Remove the cup - see steps 1-3, previous page. 3. Attach the housing to the bottom of the sprayer as shown. Rotate the housing until it clicks into place. 2. Twist and remove the suction tube and filter assembly. 4. Attach lid to paint containe...
English 7 backpack kit setup (optional) start 1. Lay cord seal (a) in backpack lid groove (b). Overlap the ends of the cord seal by approximately 1/2 inch. Cut off remaining seal. Lift seal and butt edges together and press excess seal into groove. 4. Assemble strap hooks to container using same hol...
English 8 spray controls start notice: the spray controls vary depending upon the model of sprayer you have. Refer to this page in order to learn about the controls of your particular sprayer. Power painter plus material select lever: the spray pattern is controlled by the material select lever on t...
English 9 priming with the remote suction hoses start notice: follow these steps if you plan to spray while using the remote suction hoses or the backpack kit. Notes: • the time needed to prime will vary from 30 seconds to 3 minutes depending upon the thickness of the material you are spraying. • if...
English 10 safety start practice spraying start you will need: • a scrap piece of wood or cardboard important - read before spraying priming the sprayer once you are ready to spray, it may take 20 seconds for material to spray after you pull the trigger. The sprayer may sound choppy, while at the sa...
English 11 spraying technique start 2. Remove the atomizer valve and see if it needs to be cleaned or replaced (see page 18). Also check the pump housing opening for any dirt or other obstruction and clean if necessary. 1. Unplug the sprayer immediately. Remove the adjustable spray tip assembly. Not...
English 12 cleanup (cup mode) start you will need: • waste container • cleaner nozzle and lubricant • warm soapy water if you sprayed latex materials • mineral spirits if you sprayed oil-based materials make sure you clean the sprayer in a well-ventilated area whenever cleaning with flammable solven...
English 13 12. Insert nozzle into the end of the suction tube and place into a waste container. Turn on the water and flush the suction tube until clean. 11. Thread the cleaner nozzle onto a garden hose. 8. Clean all parts thoroughly with the brush provided using a solution appropriate to the type o...
English 14 cleanup (remote suction hoses / backpack kit) start you will need: • waste container • cleaner nozzle • warm soapy water if you sprayed latex materials • mineral spirits if you sprayed oil-based materials make sure you clean the sprayer in a well-ventilated area whenever cleaning with fla...
English 15 reassembly / maintenance start you will need: • scrap piece of wood or cardboard • lubricant note:powerpaintermaxonly - refer to page 58 to see the proper way to repack the sprayer and components ito the carrying case. 1. Slide the spring onto the front end of the piston. Insert the pisto...
English 16 troubleshooting problem a: motor will not run cause solution 1. No power at wall outlet. Electrical problem or defective motor. Try new wall outlet. Take to authorized service center for repair. Problem b: motor has a low hum and does not spray cause solution 1. Seized piston disassemble ...
This unit has no servicable electrical parts. Do not attempt to service this unit yourself. English 17 problem e: excessive fogging cause solution 1. Material selector set too high set material selector to ‘stain’ 2. Holding sprayer too far from work surface hold sprayer closer to work surface probl...
English 18 replacement parts start notice: parts of your sprayer wear out with use and require regular replacement. They include the atomizer valve, piston and spring. These parts are not covered by your sprayer warranty. Moreabrasivematerialssuchaslatexpaints and stains cause these parts to wear ou...
English français español 56 (o) (n) (q) (j) (s) (a) (i) (k) (l) (m) (p) (d) (e) (f) (g) (h) (*) (*) (*) (*) (*) (r1) (r2) (c) (b) (*) (*) (q1) parts list • liste de pièces • lista de piezas.
English español français español 57 parts list • liste de pièces • lista de piezas item article articulo part no. Nº de piéce pieza no. English description français description español descripción quantity quantite cantidad a) ---------- sprayer assembly pulvérisateur rociador 1 b) 0199903 piston pi...
English français español 58 repacking diagram (power painter max only) follow the diagram below in order to properly fit the sprayer and components into the carrying case. Schéma de remballage (power painter max uniquement) suivre le schéma ci-dessous afin de replacer correctement le pulvérisateur e...
English français español 60 wagner one-year limited warranty - keep on file this product, manufactured by wagner spray tech corporation (wagner) is warranted against defects in material and workmanship for one year following date of purchase if operated in accordance with wagner’s printed recommenda...
