1. DL manuals
  2. Xerox
  3. Printer
  4. DocuColor 3535
  5. Color Manual

Xerox DocuColor 3535 Color Manual

Summary of DocuColor 3535

  • Page 1

    Fiery network controller for docucolor 3535 color guide.

  • Page 2

    This manual is part of a set of fiery network controller for docucolor 3535 ™ documentation that includes the following manuals for users and system administrators: • the quick start guide summarizes the steps for configuring the fiery and printing. It also describes how to access the online documen...

  • Page 3

    Copyright © 2003 electronics for imaging, inc. All rights reserved. This publication is protected by copyright, and all rights are reserved. No part of it may be reproduced or transmitted in any form or by any means for any purpose without express prior written consent from electronics for imaging, ...

  • Page 4

    Fcc information warning: fcc regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Class a compliance this equipment has been tested and found to comply with the limits ...

  • Page 5

    Confidentiality you agree to hold the software in confidence, disclosing the software only to authorized users having a need to use the software as permitted by this agreement and to take all reasonable precautions to prevent disclosure to other parties. Remedies and termination unauthorized use, co...

  • Page 7: Contents

    Contents about the documentation introduction about this manual xi key features of colorwise xii chapter 1: fiery color management managing color on the fiery 1-1 combine separations 1-5 rendering styles 1-6 rgb source profile 1-7 rgb separation 1-8 cmyk simulation profile 1-9 cmyk simulation method...

  • Page 8

    Viii contents using calibrator 2-6 starting calibrator 2-6 expert mode 2-8 restoring default calibration measurements 2-10 calibrating the fiery with the dtp41 2-10 calibrating the fiery with the dtp32 2-15 using the efi spectrometer es-1000 or efi densitometer ed-100 2-17 setting up the es-1000 2-1...

  • Page 9

    Ix contents appendix a: color measurement instruments using the x-rite dtp41 spectrophotometer a-1 setting up the dtp41 a-1 calibrating the dtp41 a-5 using the x-rite dtp32 densitometer a-8 setting up the dtp32 a-9 calibrating the dtp32 a-11 appendix b: importing density measurements simple ascii im...

  • Page 11

    Xi about this manual this manual explains how to manage color output on the fiery network controller for docucolor 3535, and provides information on calibration and color profiles. This manual is part of a set of documentation that includes manuals for users and system administrators. The other manu...

  • Page 12

    Xii introduction • appendix a provides information about color measurement instruments, available as separately purchased options. • appendix b describes the simple ascii file format (saiff), which can be used to import toner density measurements from measurement devices. • the fiery color reference...

  • Page 13

    Xiii key features of colorwise • select a color rendering dictionary (crd), also called a rendering style, for rgb printing. Crds allow for rich, saturated printing of presentation graphics ; smooth, accurate printing of photographs; and relative or absolute colorimetric rendering for specialized ne...

  • Page 15

    1 1-1 managing color on the fiery the following sections describe the options available from the colorwise color management system and explain how to customize the color settings for your particular needs. They provide descriptions of the preset colorwise default settings and cover additional option...

  • Page 16

    1 1-2 fiery color management fiery color management generates cmyk data to be sent to the copier. The following diagram illustrates the print options in the fiery color management process that affect color data conversions. You can access these print options when you send a print job to the fiery. M...

  • Page 17

    1 1-3 managing color on the fiery you can specify settings for the following options by selecting print options when you send a job to the fiery. Some can also be set as defaults by the administrator during fiery setup or using colorwise pro tools. Settings specified using print options override the...

  • Page 18

    1 1-4 fiery color management (other) white point 5000 k (d50)/5500 k/6500 k (d65)/ 7500 k/9300 k (default set at setup or with colorwise pro tools) applies the specified white point value to the rgb source color space definition (see page 1-7 ). To use this print option, you must choose other as the...

  • Page 19

    1 1-5 managing color on the fiery detailed explanations of how these and other settings affect your print jobs are provided in subsequent sections of this chapter. Combine separations the combine separations setting allows you to specify how to print separated cmyk data. The combine separations opti...

  • Page 20

    1 1-6 fiery color management rendering styles the rendering style option specifies a crd for color conversions. To control the appearance of images, such as prints from office applications or rgb photographs from adobe photoshop, select the appropriate rendering style. The fiery allows you to select...

  • Page 21

    1 1-7 managing color on the fiery rgb source profile the rgb source profile setting allows you to define the characteristics of the rgb data in your document so the appropriate color conversion can occur on the fiery. Commonly used monitor color spaces are available from the printer driver and from ...

  • Page 22

    1 1-8 fiery color management • none instructs the fiery to allow the rgb sources you defined elsewhere, such as in the application, to be used. When you set rgb source to none, the appearance of colors will not be independent of the file type. For example, rgb eps files will look different from rgb ...

  • Page 23

    1 1-9 managing color on the fiery cmyk simulation profile the cmyk simulation profile print option allows you to print press proofs or simulations. This setting specifies the offset press standard or other color printing device that you want to simulate. This option affects cmyk data only. With the ...

  • Page 24

    1 1-10 fiery color management cmyk simulation method the cmyk simulation method allows you to define your preferred cmyk-to-cmyk conversion technique. • quick applies one-dimensional transfer curves to adjust output densities in the cyan, magenta, yellow, and black channels. This technique leads to ...

  • Page 25

    1 1-11 managing color on the fiery in certain cases, you may want to customize the default output profile using the colorwise pro tools color editor to achieve particular color effects (see page 3-10 ). If you do so, the new customized output profile is applied to all data in the print job. Changing...

  • Page 26

    1 1-12 fiery color management n ote : use the pure black text/graphics option only when printing composites, not when printing separations. N ote : postscript applications (such as quarkxpress) may convert elements defined as rgb = 0, 0, 0 to four-color cmyk black before sending the job to the fiery...

  • Page 27

    1 1-13 managing color on the fiery n ote : postscript applications may perform their own black overprint conversions before sending the print job to the fiery. One example of how you might use this setting is with a page that contains black text on a light blue background. The background blue color ...

  • Page 28

    1 1-14 fiery color management for pdf jobs that include spot colors that are not included in the built-in table, setting spot color matching to on retains the spot color originally specified. The fiery references the built-in table to generate the closest cmyk matches of the original spot color. N o...

  • Page 29

    1 1-15 postscript printer driver for windows and mac os n ote : the following illustrations and instructions do not apply to all applications. Many applications, such as adobe pagemaker, adobe photoshop, adobe illustrator, quarkxpress, and coreldraw, have other color management options in addition t...

  • Page 30

    1 1-16 fiery color management 3. Click expert settings. The expert color settings flowchart appears. This window displays additional color settings for the fiery. Each option includes a menu from which you select settings for your specific job. 4. Click update to display the current fiery settings. ...

  • Page 31

    1 1-17 postscript printer driver for windows and mac os before you continue, complete the following procedures, as described in the user software installation guide : • install the adobeps printer driver and the fiery ppd. • select the fiery in the chooser and set it up with the fiery ppd. • install...

  • Page 32

    1 1-18 fiery color management data is printed according to all specified cmyk simulation profile and cmyk simulation method settings. When rgb separation is set to output, cmyk data is converted to the selected output profile’s cmyk color space. • colorsync color matching —provides for color convers...

  • Page 33

    1 1-19 postscript printer driver for windows and mac os 2. Choose color/grayscale from the print color menu. 3. In the printer specific options menus, choose settings for the print options described on page 1-3 . 4. If these settings are used regularly, click save settings to save them for subsequen...

  • Page 34

    1 1-20 fiery color management t o set f iery color management options from m ac os x v 10.2 or later 1. In the print dialog box, choose printer features from the menu. Choose printer features.

  • Page 35

    1 1-21 postscript printer driver for windows and mac os 2. In the printer features menus, choose settings for the print options described on page 1-3 ..

  • Page 37

    2 2-1 an overview of calibration calibrating the fiery ensures consistent, reliable color output. This chapter explains how calibration works and provides instructions for all calibration procedures. You can calibrate the fiery using colorwise pro tools in combination with any of the following color...

  • Page 38

    2 2-2 color calibration an overview of calibration calibration generates curves that adjust for the difference between the actual toner densities (measurements) and the response expected by the output profile. • measurements represent the actual color behavior of the copier. • calibration sets are s...

  • Page 39

    2 2-3 understanding calibration understanding calibration although most users’ needs are met by the default calibration set, the fiery allows you to choose a calibration set to customize calibration for specialized jobs. Calibration allows you to: • maximize the color reproduction capabilities of th...

  • Page 40

    2 2-4 color calibration measurements measurement files contain numerical values that correspond to the toner density produced by the copier when it prints solid cyan, magenta, yellow, and black, and graduated tints of those colors. To create a measurement file, print a page of color patches. Then me...

  • Page 41

    2 2-5 understanding calibration to monitor print quality, print the following color reference pages: • color charts from command workstation (see the job management guide ) • color reference pages included with the user software (see the user software installation guide ) all these pages include ful...

  • Page 42

    2 2-6 color calibration using calibrator colorwise pro tools calibrator allows you to calibrate the fiery using the measurement method of your choice. Changing the calibration has the potential to affect all jobs for all users, so consider limiting the number of people authorized to perform calibrat...

  • Page 43

    2 2-7 using calibrator 3. Use the calibrator window to perform the calibration method of your choice. Procedures for each calibration method are described in subsequent sections of this chapter. Calibration methods appear in this menu.

  • Page 44

    2 2-8 color calibration expert mode calibrator provides two modes: standard mode and expert mode. You can perform all essential calibration tasks while in standard mode. Expert mode offers two additional options: print pages and view measurements. With the print pages option, print a calibration com...

  • Page 45

    2 2-9 using calibrator with the view measurements option, you can view the current set of measurements as a table or graph that shows both the measurements and the target curves. When more than one profile uses the same target, an additional menu called plot against appears in the upper-right corner...

  • Page 46

    2 2-10 color calibration restoring default calibration measurements use the following procedure to return to default preset calibration measurements. T o restore default calibration measurements 1. In the main calibrator window, click restore device. 2. Click ok to restore the preset default calibra...

  • Page 47

    2 2-11 using calibrator t o calibrate the f iery using the dtp41 1. Start calibrator. For instructions on starting calibrator, see page 2-6 . 2. Choose x-rite dtp41 as the measurement method. 3. In the check print settings pane, choose the desired calibration set. Choose the appropriate calibration ...

  • Page 48

    2 2-12 color calibration 6. Retrieve the measurement page from the copier. 7. In the get measurements pane, click measure. The measurement options dialog box displays the specified page type and paper size options. 8. Click measure. 9. If necessary, choose the appropriate com port for the dtp41 from...

  • Page 49

    2 2-13 using calibrator 10. Insert the measurement page into the dtp41, starting with the cyan strip. Follow the on-screen instructions to align the page properly. 11. Click read strip. The dtp41 pulls the measurement page through automatically. After the measurement page is read, calibrator instruc...

  • Page 50

    2 2-14 color calibration 12. Repeat the measurement process for the magenta, yellow, and black strips. A check mark appears on the circle of the color just read, and the status field indicates the color was measured successfully. Click previous or next to reverse or advance to another step in the me...

  • Page 51

    2 2-15 using calibrator calibrating the fiery with the dtp32 using the dtp32, you can quickly measure color patches and download these measurements to the fiery using colorwise pro tools calibrator. N ote : before using colorwise pro tools and the dtp32 to calibrate the fiery, follow the instruction...

  • Page 52

    2 2-16 color calibration for input tray, specify the paper source. 6. Retrieve the measurement page from the copier. 7. Click measure in the get measurements pane. The measurement options dialog box displays the specified page type and paper size options. 8. Click measure. In the dialog box that app...

  • Page 53

    2 2-17 using the efi spectrometer es-1000 or efi densitometer ed-100 9. When the status field indicates that the measurements were read successfully, click accept. 10. Click ok in the measure dialog box. 11. Click apply in the calibrator window to implement the new calibration set. 12. Click ok in t...

  • Page 54

    2 2-18 color calibration the following illustration shows the different parts of the es-1000. Setting up the ed-100 to use the ed-100 for calibration purposes, you must first set it up for use with your computer. For complete instructions on setting up the ed-100, see the documentation that is inclu...

  • Page 55

    2 2-19 using the efi spectrometer es-1000 or efi densitometer ed-100 calibrating the fiery with the es-1000 or ed-100 you can use colorwise pro tools in conjunction with the es-1000 or ed-100 to calibrate the fiery. T o calibrate the f iery using the es-1000 or ed-100 1. Start calibrator. For instru...

  • Page 56

    2 2-20 color calibration for page type, choose either 34 or 21 sorted patches, or 34 or 21 randomized patches. Sorted patches are printed on the page in the order of their hue and saturation levels. Randomized patches are printed on the page in random order, to help compensate for density inconsiste...

  • Page 57

    2 2-21 using the efi spectrometer es-1000 or efi densitometer ed-100 if necessary, choose the appropriate com port for the es-1000 or ed-100 from the port menu. When you click start, the measurements window appears. Directions for measuring the patches appear in the status area. 9. Place the es-1000...

  • Page 58

    2 2-22 color calibration when the patch has been measured successfully, a check mark appears in the patch preview in the measurements window. The window identifies and highlights the next patch to be measured. 10. Repeat step 9 to measure each successive patch on the measurement page. Start with a1 ...

  • Page 59

    2 2-23 using autocal or colorcal using autocal or colorcal autocal and colorcal allow you to calibrate the fiery without using an additional spectrophotometer or densitometer. Instead, these methods use the copier’s built-in scanner to measure toner density values. Autocal is compatible with earlier...

  • Page 60

    2 2-24 color calibration t o calibrate with c olor w ise p ro t ools and a uto c al or c olor c al 1. Start colorwise pro tools (on your mac os or windows computer). 2. Start calibrator. For instructions on starting calibrator, see page 2-6 . 3. In the select measurement method pane, choose autocal ...

  • Page 61

    2 2-25 using autocal or colorcal 8. Retrieve the measurement page from the copier. 9. Click measure in the get measurements pane. If you chose the autocal method, skip to step 18 . If you chose the colorcal method, an alert message appears, asking if you want to calibrate the copier’s scanner. 10. I...

  • Page 62

    2 2-26 color calibration 16. To perform the scanner calibration, click continue in the colorcal dialog box. After the scanner is calibrated, another dialog box appears, prompting you to calibrate the fiery. 17. Click measure in the autocal or colorcal get measurements pane. 18. Follow the directions...

  • Page 63

    2 2-27 calibrating from the xerox docucolor 3535 21. Press the xerox docucolor 3535 scan button (large green button). 22. Click ok in the calibrator information dialog box. 23. Click apply in the main calibrator window to implement the new calibration set. 24. Click ok in the information dialog box....

  • Page 64

    2 2-28 color calibration 5. In the auto gradation adjustment screen, select the appropriate option: • print job—to calibrate the line screen calibration set. • network controller 1 or network controller 2—to calibrate the dot screen calibration set. 6. Follow the on-screen instructions to load the p...

  • Page 65

    3 3-1 profile manager designed to give you flexible control of color printing, colorwise pro tools include the following color management tools: • calibrator (see chapter 2 ) • color editor • profile manager • color setup colorwise pro tools for windows and mac os computers are fundamentally the sam...

  • Page 66

    3 3-2 colorwise pro tools profile manager profile manager allows you to manage and edit icc profiles. In the case of the fiery, these profiles are divided into rgb source, simulation, and output profiles: • rgb source contains all monitor profiles resident on the fiery. Rgb source profiles are used ...

  • Page 67

    3 3-3 profile manager setting the default profiles the default profiles are applied to all print jobs sent to the fiery, unless you override them using print options. Therefore, the defaults should be the most commonly used profiles. T o specify a default profile 1. Start colorwise pro tools and cli...

  • Page 68

    3 3-4 colorwise pro tools 3. In the profile settings dialog box, click default and click apply. 4. Click ok. In the main profile manager window, the target icon appears next to the new default profile you specified. 5. Repeat steps 2 through 4 for each type of profile. If no default is set for rgb s...

  • Page 69

    3 3-5 profile manager 2. If the desired profile does not appear, click browse to go to a different directory. Browse to the directory containing the profile you want to download and click ok. 3. When the profile you want to download appears in the list in the main profile manager window, select it. ...

  • Page 70

    3 3-6 colorwise pro tools editing profiles you can customize the profiles on the fiery to meet your specific needs and the characteristics of your copier using color editor, either directly or through profile manager. For more information on editing profiles, see “color editor” on page 3-10. Managin...

  • Page 71

    3 3-7 profile manager t o delete profiles from the f iery 1. Start colorwise pro tools and click profile manager. 2. Select the profile you want to delete and click delete. A warning dialog box asks you to confirm the deletion. N ote : you cannot delete preset profiles, profiles that are currently s...

  • Page 72

    3 3-8 colorwise pro tools t o define a custom simulation profile 1. Start colorwise pro tools and click profile manager. For the purposes of this example, assume dic-new is a custom simulation profile created with color editor and, as such, no information is displayed for dic-new under the heading “...

  • Page 73

    3 3-9 profile manager n ote : although you cannot delete a preset profile, you can use the name of a preset profile name for your edited profile when you select the “appear in driver as” option. This replaces the preset profile with your own profile. In profile settings, you can also change profile ...

  • Page 74

    3 3-10 colorwise pro tools if you do not define a custom simulation profile, your job will print with cmyk simulation profile set to none. If you do not define a custom rgb source or output profile, the default profile is used. Considerations for defining output profiles the procedures for defining ...

  • Page 75

    3 3-11 color editor color editor also has several edit modes for editing simulations: • master —create a custom master simulation that affects all print jobs to which it is applied, unless a linked simulation exists for the selected combination of simulation profile, simulation method, and output pr...

  • Page 76

    3 3-12 colorwise pro tools 3. Choose a profile to edit and click select. Another method is to open the profile manager, select a profile, and then click edit. 4. For a simulation profile, choose master from the edit mode menu. For an output profile, choose custom from the edit mode menu. For instruc...

  • Page 77

    3 3-13 color editor 5. Select the colors you want to edit by turning colors off and on. The eye icon to the left of each color indicates whether that color is visible on the graph and will be affected by changes to the curves, brightness, and dot gain controls. You can view and edit all four colors ...

  • Page 78

    3 3-14 colorwise pro tools if you use dot gain values, apply the settings first, so that the curves are deflected from their straight-line positions. Then make edits to the new curves. When you adjust dot gain values, all existing points on the curve are removed. A warning dialog box allows you to c...

  • Page 79

    3 3-15 color editor n ote : you should adjust points in this way only after you have entered the dot gain and brightness values. For greater precision, type percentages in the input and output fields or use the arrow keys on the keyboard to adjust the curve. To use the arrow keys, you must first cli...

  • Page 80

    3 3-16 colorwise pro tools t o edit a simulation in q uick , f ull (s ource gcr), or f ull (o utput gcr) mode 1. Start colorwise pro tools and click color editor. 2. Choose simulation from the view menu, select the simulation profile to edit, and then click select. Another method is to open the prof...

  • Page 81

    3 3-17 color editor 4. Edit and save the simulation, as described in steps 5 through 10 of the procedure starting on page 3-13 . For this new simulation to be automatically applied to a print job, the cmyk simulation, simulation method, and output profile settings must be the same as those used when...

  • Page 82

    3 3-18 colorwise pro tools t o correct the gray balance of an output profile 1. On the copier control panel, press the access button (key icon). 2. Enter your password. 3. Select confirm. 4. Choose system settings>system settings>scan mode setting>others. 5. For color_space, select 1 (drgb). 6. Choo...

  • Page 83

    3 3-19 color editor 12. If the output profile contains no edit points, continue to step 14 . If the output profile contains edit points from a previous autogray session, choose an action from the following warning. Refine reuses edits points from a previous session in an attempt to make them more ac...

  • Page 84

    3 3-20 colorwise pro tools 14. Click ok to confirm printing of the measurement page. 15. Retrieve the page from the copier. 16. Follow the directions in the dialog box for placing the kodak gray scale strip and the autogray measurement page on the copier glass, and click continue. Messages display t...

  • Page 85

    3 3-21 color editor checking edited profiles to view a printed sample of a profile before you save it to the fiery, print one of the following: • comparison page provided with colorwise pro tools, which shows a comparison of images and colored patches with and without edits • user-defined calib.Ps i...

  • Page 86

    3 3-22 colorwise pro tools color setup use color setup to set the default colorwise settings for the fiery. To access color setup, click its icon in the colorwise pro tools main window. Setting default colorwise options color setup allows you to configure the default color management settings for th...

  • Page 87

    3 3-23 color setup for those color options that offer multiple choices, make your selection from the menu that appears. For rgb separation, select the radio button next to the option name. For other options, select a check box next to the option name. Once you have made your changes, you must click ...

  • Page 89

    A a-1 color measurement instruments this appendix explains how to set up and calibrate the following color measurement instruments, available as separately purchased options: • x-rite dtp41 automatic scanning spectrophotometer • x-rite dtp32 automatic scanning densitometer using the x-rite dtp41 spe...

  • Page 90

    A a-2 color measurement instruments t o connect the x-r ite dtp41 to the computer 1. Turn off the computer. 2. Unpack the x-rite dtp41 and remove the spacer from the measurement page slot. 3. Plug the square end of the interface cable (looks like a modular phone plug) into the serial interface conne...

  • Page 91

    A a-3 color measurement instruments 4. Attach the connector to the computer. For a windows computer, insert the 8-pin mini-din end of the interface cable into the 9-pin db9 connector cable adapter. Insert the 9-pin end into the com1 or com2 port on the computer and tighten the screws. If the availab...

  • Page 92

    A a-4 color measurement instruments n ote : for mac os computers with a usb port (for example, an imac), you need an adapter to connect the dtp41 to your computer. For information on supported adapters, see the x-rite, inc. Web site (www.X-rite.Com). 5. Use the ac adapter to provide power. Plug the ...

  • Page 93

    A a-5 color measurement instruments calibrating the dtp41 for the best color accuracy, calibrate the x-rite dtp41 spectrophotometer every time you calibrate the fiery. You can initiate the calibration sequence in colorwise pro tools calibrator as part of the process of fiery calibration. The compute...

  • Page 94

    A a-6 color measurement instruments 4. In the get measurements pane, click measure. 5. In the measurement options dialog box, click measure. 6. Choose the appropriate com port for the dtp41 from the available ports menu. The instructions area displays instructions for selecting the port..

  • Page 95

    A a-7 color measurement instruments 7. Click utilities. The utilities dialog box appears. To view version and serial number information, click show dtp-41 info, and then click done. 8. Click calibrate dtp-41. The instrument calibration dialog box appears..

  • Page 96

    A a-8 color measurement instruments 9. If you have not already done so, remove the shipping spacer from the measurement page slot. 10. Insert the end of the color reflection reference strip into the calibration strip entrance on the dtp41. Center the arrow on the strip below the alignment mark (see ...

  • Page 97

    A a-9 color measurement instruments setting up the dtp32 before you calibrate the fiery using the x-rite dtp32, you need to connect, configure, and calibrate the densitometer to prepare for measuring the printed patches (see “calibrating the dtp32” on page a-11). For additional information about set...

  • Page 98

    A a-10 color measurement instruments for a mac os computer, connect the 8-pin mini-din plug directly into the serial port of the computer. N ote : for mac os computers with a usb port (for example, an imac), you need an adapter to connect the dtp32 to your computer. For information on supported adap...

  • Page 99

    A a-11 color measurement instruments calibrating the dtp32 you will need the black-and-white x-rite auto-cal strip included with the densitometer. Calibrating the densitometer does not require colorwise pro tools. T o calibrate the x-r ite dtp32 1. Connect the densitometer to the computer and supply...

  • Page 101

    B b-1 importing density measurements this appendix describes simple ascii file format, which can be used to import density measurements from measurement devices. To use your own measurement data from an alternate measurement instrument, record your individual readings in a text file and structure it...

  • Page 102

    B b-2 importing density measurements example of 1d status t density for efi 34 patch page this file format is used to specify the status t density measurements of the efi 34 patch page. The value in the first column is the patch number. The first patch must be 1 and the last must be 34. #!Efi 3 # ef...

  • Page 103

    B b-3 importing density measurements example of 1d status t density for an arbitrary page this file format is used to specify the status t density measurements of a user-defined patch page. The value in the first column is the ink/toner percentage of the patch. The first percentage must be 0 and the...

  • Page 105: Index

    Index a absolute colorimetric rendering style 1-6 apple standard setting, rgb source profile option 3-2 apple standard setting, rgb source profile option 1-7 autocal calibration 2-24 b black detection option 1-5 black overprint option 1-4, 1-12 black text and line art 1-4, 1-11 to 1-13 brightness op...

  • Page 106

    I-2 index comparison page 2-8, 3-21 composites, printing 1-3, 1-5, 1-12, 1-14 configuration page 2-5 contrast icc rendering style 1-6 custom simulations 1-9 d default color controls set in setup 1-3 densitometer dtp32 2-15 to 2-17, a-8 to a-11 ed-100 2-17 to 2-22 density values about 2-3, 2-5 import...

  • Page 107

    I-3 index p pantone coated color reference 1-14 passwords for calibration 2-2, 2-6 for profile management 3-2 patches page 2-4 perceptual icc rendering style 1-6 phosphors option 1-3 photographic rendering style 1-6 postscript color issues 1-2, 1-8, 1-12, 1-13 postscript color management 1-17 postsc...

  • Page 108

    I-4 index t targets, for calibration 2-3 test page 2-5 text and graphics enhancement option 1-5 transfer functions 2-3 two-way communication 1-7, 1-9, 1-11 u undercolor removal (ucr) 1-8 w white point option 1-4 windows color management options 1-15 to 1-16.