1. DL manuals
  2. Xerox
  3. Printer
  4. DocuColor 1632
  5. Service Manual

Xerox DocuColor 1632 Service Manual

Summary of DocuColor 1632

  • Page 1

    701p40660 september, 2003 docucolor 3535/2240/1632, workcentre m24 service manual prelaunch training use only! T he d ocument c ompany xerox caution certain components in this device are susceptible to damage from electrostatic discharge. Observe all esd procedures to avoid component damage..

  • Page 2: Introduction

    09/03 1 dc 3535/2240/1632, wc m24 introduction initial issue introduction about this manual ........................................................................................................... Iii organization ......................................................................................

  • Page 3

    09/03 2 dc 3535/2240/1632, wc m24 initial issue introduction.

  • Page 4

    09/03 iii dc 3535/2240/1632, wc m24 introduction initial issue about this manual this service manual is part of the multinational documentation system for docucolor 3535/ 2240/1632 copier/printers. The service documentation is used in order to diagnose machine malfunctions, adjust components and has...

  • Page 5

    09/03 iv dc 3535/2240/1632, wc m24 initial issue introduction warnings, cautions, and notes warnings, cautions, and notes will be found throughout the service documentation. The words warning or caution may be listed on an illustration when the specific component associated with the potential hazard...

  • Page 6

    09/03 v dc 3535/2240/1632, wc m24 introduction initial issue electrostatic discharge (esd) field service kit the purpose of the esd protection program is to preserve the inherent reliability and quality of electronic components that are handled by the field service personnel. This program is being i...

  • Page 7

    09/03 vi dc 3535/2240/1632, wc m24 initial issue introduction signal nomenclature refer to figure 7 for an example of signal nomenclature used in circuit diagrams and bsds. Figure 7 signal nomenclature voltage measurement and specifications measurements of dc voltage must be made with reference to t...

  • Page 8

    09/03 vii dc 3535/2240/1632, wc m24 introduction initial issue translated warnings.

  • Page 9

    09/03 viii dc 3535/2240/1632, wc m24 initial issue introduction introduction symbology and nomenclature warning a warning is used whenever an operating or maintenance procedure, a practice, condi- tion, or statement, if not strictly observed, could result in personal injury. Danger: une note danger ...

  • Page 10

    09/03 ix dc 3535/2240/1632, wc m24 introduction initial issue danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer des activités de maintenance ou de réglage avec l'équipement sur marche ou avec le cordon d'alimentation branché. Rep 1.7 dev/btr2/dts hvps; bcr hvps warning t...

  • Page 11

    09/03 x dc 3535/2240/1632, wc m24 initial issue introduction rep 1.19 one-touch panel warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électr...

  • Page 12

    09/03 xi dc 3535/2240/1632, wc m24 introduction initial issue rep 4.2 ibt motor assembly warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs éle...

  • Page 13

    09/03 xii dc 3535/2240/1632, wc m24 initial issue introduction danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer des activités de maintenance ou de réglage avec l'équipement sur marche ou avec le cordon d'alimentation branché. Rep 5.10 set gate solenoid assembly warning ...

  • Page 14

    09/03 xiii dc 3535/2240/1632, wc m24 introduction initial issue warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectue...

  • Page 15

    09/03 xiv dc 3535/2240/1632, wc m24 initial issue introduction rep 7.4 tray 1 feed/lift motor warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des choc...

  • Page 16

    09/03 xv dc 3535/2240/1632, wc m24 introduction initial issue activités de maintenance ou de réglage avec l'équipement sur marche ou avec le cordon d'alimentation branché. Rep 7.16 tray 2 feeder (3tm) warning to avoid personal injury or shock, do not perform repair or adjustment activities with the ...

  • Page 17

    09/03 xvi dc 3535/2240/1632, wc m24 initial issue introduction warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer...

  • Page 18

    09/03 xvii dc 3535/2240/1632, wc m24 introduction initial issue warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectue...

  • Page 19

    09/03 xviii dc 3535/2240/1632, wc m24 initial issue introduction rep 9.26 atc sensor warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électri...

  • Page 20

    09/03 xix dc 3535/2240/1632, wc m24 introduction initial issue danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer des activités de maintenance ou de réglage avec l'équipement sur marche ou avec le cordon d'alimentation branché. Rep 12.8 finisher drive motor warning to avo...

  • Page 21

    09/03 xx dc 3535/2240/1632, wc m24 initial issue introduction to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer des acti...

  • Page 22

    09/03 xxi dc 3535/2240/1632, wc m24 introduction initial issue warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Danger: afin d'éviter des blessures ou des chocs électriques, ne pas effectuer...

  • Page 23

    09/03 xxii dc 3535/2240/1632, wc m24 initial issue introduction.

  • Page 24: 1 Service Call Procedures

    09/03 1-1 dc 3535/2240/1632, wc m24 service call procedures initial issue 1 service call procedures service call procedures.................................................................................................. 1-3 initial actions .............................................................

  • Page 25

    09/03 1-2 dc 3535/2240/1632, wc m24 initial issue service call procedures.

  • Page 26

    09/03 1-3 dc 3535/2240/1632, wc m24 service call procedures service call procedures initial issue service call procedures service strategy the service strategy for the docucolor 3535/2240/1632 copier/printer is to perform any high frequency service item (hfsi) actions before attempting to repair any...

  • Page 27

    09/03 1-4 dc 3535/2240/1632, wc m24 initial actions initial issue service call procedures initial actions purpose the purpose of the initial action section of the service call procedures is to determine the rea- son for the service call and to identify and organize the actions which must be performe...

  • Page 28

    09/03 1-5 dc 3535/2240/1632, wc m24 call flow service call procedures initial issue call flow this procedure should be performed at every service call. Initial actions ask the operator about the problem. If the problem appears to be related to operator error, or an attempt to perform a job outside o...

  • Page 29

    09/03 1-6 dc 3535/2240/1632, wc m24 call flow initial issue service call procedures y n • verify machine settings • reload system software • replace the ess pwb ( pl 13.1 ). E e e e f f.

  • Page 30

    09/03 1-7 dc 3535/2240/1632, wc m24 call flow service call procedures initial issue the problem is image quality (print mode) y n verify that the ac power, scan, and ddi cables are connected correctly. If the cables are ok, refer to the network controller service documentation to verify the correct ...

  • Page 31

    09/03 1-8 dc 3535/2240/1632, wc m24 detailed maintenance activities initial issue service call procedures detailed maintenance activities (hfsi) procedure 1. Clean the adc sensor on every call. 2. Enter diagnostics and select dc135 . 3. Perform the service actions in table 1 for any high frequency s...

  • Page 32

    09/03 1-9 dc 3535/2240/1632, wc m24 cleaning procedures, final actions service call procedures initial issue cleaning procedures purpose the purpose is to provide cleaning procedures to be performed at every call. Procedure caution do not use any solvents unless directed to do so by the service manu...

  • Page 33

    09/03 1-10 dc 3535/2240/1632, wc m24 cleaning procedures, final actions initial issue service call procedures.

  • Page 34: 2 Status Indicator Raps

    09/03 2-1 dc 3535/2240/1632, wc m24 status indicator raps initial issue 2 status indicator raps chain 1 1-300 rap....................................................................................................................... 2-13 1-301 rap........................................................

  • Page 35

    09/03 2-2 dc 3535/2240/1632, wc m24 initial issue status indicator raps 4-361 drum motor ........................................................................................................... 2-67 4-362 iot nvm read write ............................................................................

  • Page 36

    09/03 2-3 dc 3535/2240/1632, wc m24 status indicator raps initial issue 8-184 registration sensor off......................................................................................... 2-169 8-620 regicon temp sensor ................................................................................

  • Page 37

    09/03 2-4 dc 3535/2240/1632, wc m24 initial issue status indicator raps 12-262 eject clamp home sensor off............................................................................ 2-271 12-267 decurler ..................................................................................................

  • Page 38

    09/03 2-5 dc 3535/2240/1632, wc m24 status indicator raps initial issue 16-729 tiff data ............................................................................................................ 2-353 16-730 art command ................................................................................

  • Page 39

    09/03 2-6 dc 3535/2240/1632, wc m24 initial issue status indicator raps 20-512 endless loop detected ....................................................................................... 2-405 20-513 receive command error ...............................................................................

  • Page 40

    09/03 2-7 dc 3535/2240/1632, wc m24 status indicator raps initial issue 20-790 line 1 not connected ......................................................................................... 2-457 20-791 line 0 (extension) not connected ...................................................................

  • Page 41

    09/03 2-8 dc 3535/2240/1632, wc m24 initial issue status indicator raps 83-752 job number limit error ....................................................................................... 2-509 83-753 document image memory full .........................................................................

  • Page 42

    09/03 2-9 dc 3535/2240/1632, wc m24 status indicator raps initial issue 84-758 wait tcr time-out ............................................................................................. 2-560 84-759 wait tcc time-out .................................................................................

  • Page 43

    09/03 2-10 dc 3535/2240/1632, wc m24 initial issue status indicator raps 102-362 no object .......................................................................................................... 2-612 102-363 invalid id ................................................................................

  • Page 44

    09/03 2-11 dc 3535/2240/1632, wc m24 status indicator raps initial issue 116-359 plw software ................................................................................................... 2-663 116-360 smb software ..................................................................................

  • Page 45

    09/03 2-12 dc 3535/2240/1632, wc m24 initial issue status indicator raps.

  • Page 46

    09/03 2-13 dc 3535/2240/1632, wc m24 1-300 status indicator raps initial issue 1-300 rap the left cover is open. Procedure enter dc330 [001-301] and press the start button. Open and close the left cover ( pl 2.7 ). The display changes state. Y n +24 vdc is measured between +24 lvps p/j502-1 and gnd(...

  • Page 47

    09/03 2-14 dc 3535/2240/1632, wc m24 1-301 initial issue status indicator raps 1-301 rap the left lower cover is open procedure enter dc330 [001-302] and press the start button. Open the left lower cover. Actuate the lh lower cover interlock switch ( pl 2.3 ) with a screwdriver. The display changes ...

  • Page 48

    09/03 2-15 dc 3535/2240/1632, wc m24 1-302 status indicator raps initial issue 1-302 rap the front cover or the right side cover is open. Initial actions check the operation of the actuator and the switch. Procedure open the front cover. Cheat the front interlock switch. The fault code 001-302 is cl...

  • Page 49

    09/03 2-16 dc 3535/2240/1632, wc m24 1-303 initial issue status indicator raps 1-303 rap the tray module left door is open. Procedure enter dc330 [001-304] and press the start button. Actuate the tray module lh cover interlock switch ( pl 16.13 ) with a screwdriver. The display changes state. Y n +2...

  • Page 50

    09/03 2-17 dc 3535/2240/1632, wc m24 1-306 status indicator raps initial issue 1-306 rap the duplex cover is open. Procedure enter dc330 [008-300] and press the start button. Open the duplex transport. Actuate the duplex cover interlock switch ( pl 12.2 ) with a screwdriver. The display changes stat...

  • Page 51

    09/03 2-18 dc 3535/2240/1632, wc m24 1-306 initial issue status indicator raps.

  • Page 52

    09/03 2-19 dc 3535/2240/1632, wc m24 3-205, 3-206 status indicator raps initial issue 3-205 billing meter mismatch the billing meters on the three serialized pwbs do not match. Procedure switch the power off then on. If the fault remains, perform gp 10 . 3-206 billing restoration failure one of the ...

  • Page 53

    09/03 2-20 dc 3535/2240/1632, wc m24 3-317 , 3-318 initial issue status indicator raps 3-317 iit software failure configuration mismatch procedure change the position of the document sensor. The problem continues. Y n return to service call procedures. Rewrite the nvm values. 3-318 iit software fail...

  • Page 54

    09/03 2-21 dc 3535/2240/1632, wc m24 3-319 , 3-320 status indicator raps initial issue 3-319 iit video driver failure video driver declared a dma or compression error. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the software. If the...

  • Page 55

    09/03 2-22 dc 3535/2240/1632, wc m24 3-321, 3-322 initial issue status indicator raps 3-321 iit-ess communication failure 2 controller received check code error (wrong sequence number in sent message packet). Procedure switch the power off then on. The problem continues. Y n return to service call p...

  • Page 56

    09/03 2-23 dc 3535/2240/1632, wc m24 3-323, 3-324 status indicator raps initial issue 3-323 iit-ess communication failure 4 controller received check code error (wrong message packet length in sent packet). Procedure switch the power off then on. The problem continues. Y n return to service call pro...

  • Page 57

    09/03 2-24 dc 3535/2240/1632, wc m24 3-325, 3-326 initial issue status indicator raps 3-325 iit-ess communication failure 6 controller received check code error (parity error in iiss). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the...

  • Page 58

    09/03 2-25 dc 3535/2240/1632, wc m24 3-327, 3-328 status indicator raps initial issue 3-327 iit-ess communication failure 8 controller received check code error (over-run error in iiss). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall t...

  • Page 59

    09/03 2-26 dc 3535/2240/1632, wc m24 3-329, 3-330 initial issue status indicator raps 3-329 iit-ess communication failure 10 controller received check code error (wrong sequence number in received message packet). Procedure switch the power off then on. The problem continues. Y n return to service c...

  • Page 60

    09/03 2-27 dc 3535/2240/1632, wc m24 3-331, 3-332 status indicator raps initial issue 3-331 iit-ess communication failure 12 controller received check code error (wrong message packet length in received packet). Procedure switch the power off then on. The problem continues. Y n return to service cal...

  • Page 61

    09/03 2-28 dc 3535/2240/1632, wc m24 3-333, 3-334 initial issue status indicator raps 3-333 iit-ess communication failure 14 controller received check code error (parity error in uart) procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the...

  • Page 62

    09/03 2-29 dc 3535/2240/1632, wc m24 3-335, 3-336 status indicator raps initial issue 3-335 iit-ess communication failure 16 controller received check code error (uart over-run error). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the...

  • Page 63

    09/03 2-30 dc 3535/2240/1632, wc m24 3-337, 3-340 initial issue status indicator raps 3-337 iit-ess communication failure 18 controller received check code error (reception aborted after header received). Procedure switch the power off then on. The problem continues. Y n return to service call proce...

  • Page 64

    09/03 2-31 dc 3535/2240/1632, wc m24 3-341, 3-342 status indicator raps initial issue 3-341 iot-ess communication failure 2 controller received check code error (wrong sequence number in sent message packet). Procedure switch the power off then on. The problem continues. Y n return to service call p...

  • Page 65

    09/03 2-32 dc 3535/2240/1632, wc m24 3-343, 3-345 initial issue status indicator raps 3-343 iot-ess communication failure 4 controller received check code error (wrong message packet length in sent packet). Procedure switch the power off then on. The problem continues. Y n return to service call pro...

  • Page 66

    09/03 2-33 dc 3535/2240/1632, wc m24 3-346, 3-347 status indicator raps initial issue 3-346 iot-ess communication failure 6 controller received check code error (parity error in iot). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the ...

  • Page 67

    09/03 2-34 dc 3535/2240/1632, wc m24 3-348, 3-349 initial issue status indicator raps 3-348 iot-ess communication failure 8 controller received check code error (iot over-run error). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the s...

  • Page 68

    09/03 2-35 dc 3535/2240/1632, wc m24 3-350, 3-351 status indicator raps initial issue 3-350 iot-ess communication failure 10 controller received check code error (wrong sequence number in received message packet). Procedure switch the power off then on. The problem continues. Y n return to service c...

  • Page 69

    09/03 2-36 dc 3535/2240/1632, wc m24 3-352, 3-353 initial issue status indicator raps 3-352 iot-ess communication failure 12 controller received check code error (wrong message packet length in received packet). Procedure switch the power off then on. The problem continues. Y n return to service cal...

  • Page 70

    09/03 2-37 dc 3535/2240/1632, wc m24 3-354, 3-355 status indicator raps initial issue 3-354 iot-ess communication failure 14 controller received check code error (uart parity error). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the s...

  • Page 71

    09/03 2-38 dc 3535/2240/1632, wc m24 3-356, 3-357 initial issue status indicator raps 3-356 iot-ess communication failure 16 controller received check code error (uart over-run error). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the...

  • Page 72

    09/03 2-39 dc 3535/2240/1632, wc m24 3-358, 3-359 status indicator raps initial issue 3-358 iot-ess communication failure 18 controller received check code error. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the software. If the prob...

  • Page 73

    09/03 2-40 dc 3535/2240/1632, wc m24 3-360, 3-364 initial issue status indicator raps 3-360 iot-ess initialization failure iot driver initialization failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the software. If the problem c...

  • Page 74

    09/03 2-41 dc 3535/2240/1632, wc m24 3-365, 3-366 status indicator raps initial issue 3-365 overflow on write loop back the extended data exceeds the reserved buffer size procedure switch the power off then on. The problem continues. Y n return to service call procedures. Replace the ess pwb ( pl 13...

  • Page 75

    09/03 2-42 dc 3535/2240/1632, wc m24 3-370, 3-747 initial issue status indicator raps 3-370 marker code detect failure the end code cannot be found in the compressed data. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Replace the ram ( pl 13.1 ...

  • Page 76

    09/03 2-43 dc 3535/2240/1632, wc m24 3-750, 3-761 status indicator raps initial issue 3-750 insufficient number of document pages insufficient number of pages programed when making a book. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Set the n...

  • Page 77

    09/03 2-44 dc 3535/2240/1632, wc m24 3-941, 3-942 initial issue status indicator raps 3-941 insufficient page memory procedure switch the power off then on. The problem continues. Y n return to service call procedures. Perform the operation again. 3-942 document size error dadf mode: the dadf docume...

  • Page 78

    09/03 2-45 dc 3535/2240/1632, wc m24 3-946, 3-947 status indicator raps initial issue 3-946 tray 1 not in position tray 1 not in ready position. Initial actions • check that the paper size setting is correct. • check the tray 1 paper size sensor for damage or incorrect mounting. Repair or replace as...

  • Page 79

    09/03 2-46 dc 3535/2240/1632, wc m24 3-948, 3-949 initial issue status indicator raps 3-948 tray 3 not in position tray 3 not in ready position. Initial actions • check that the paper size setting is correct. • check the tray 3 paper size sensor for damage or incorrect mounting. Repair or replace as...

  • Page 80

    09/03 2-47 dc 3535/2240/1632, wc m24 3-950, 3-951 status indicator raps initial issue 3-950 tray 1 empty paper is not detected in tray 1 procedure remove tray 1. Enter dc330 [007-120] and press start. Actuate the tray 1 no paper sensor ( pl 2.4 ). The display changes state. Y n press stop. Check the...

  • Page 81

    09/03 2-48 dc 3535/2240/1632, wc m24 3-951, 3-952 initial issue status indicator raps figure 2 3-951 rap circuit diagram - tray 2 no paper sensor (3tm) 3-952 tray 3 empty paper is not detected in tray 3 procedure the machine is equipped with a 3tm. Y n remove tray 3. Enter dc330 [007-122] and press ...

  • Page 82

    09/03 2-49 dc 3535/2240/1632, wc m24 3-952, 3-953 status indicator raps initial issue figure 2 3-952 rap circuit diagram - tray 3 no paper sensor (3tm) 3-953 tray 4 empty paper is not detected in tray 4. Procedure the machine is equipped with a 3tm. Y n remove tray 4. Enter dc330 [007-123] and press...

  • Page 83

    09/03 2-50 dc 3535/2240/1632, wc m24 3-953, 3-954 initial issue status indicator raps figure 2 9-353 rap circuit diagram - tray 4 no paper sensor (3tm) 3-954 tray 5 empty paper is not detected in tray 5. Procedure enter dc330 [007-125] and press start. Actuate the tray 5 no paper sensor. The display...

  • Page 84

    09/03 2-51 dc 3535/2240/1632, wc m24 3-958, 3-959 status indicator raps initial issue 3-958 tray 5 paper size mismatch the paper in the tray 5 does not match the paper size selected. Procedure the correct size paper is loaded in tray 5. Y n load the correct size paper and return to service call proc...

  • Page 85

    09/03 2-52 dc 3535/2240/1632, wc m24 3-960, 3-961 initial issue status indicator raps 3-960 tray 2 paper size mismatch the paper in tray 2 does not match the paper size selected. Procedure the correct size paper is loaded in tray 2. Y n load the correct size paper and return to service call procedur...

  • Page 86

    09/03 2-53 dc 3535/2240/1632, wc m24 3-962, 3-965 status indicator raps initial issue 3-962 tray 4 paper size mismatch the paper in tray 4 does not match the paper size selected. Procedure the machine is equipped with a 3tm. Y n the correct size paper is loaded in tray 4. Y n load the correct size p...

  • Page 87

    09/03 2-54 dc 3535/2240/1632, wc m24 3-971, 3-972 initial issue status indicator raps 3-971 magnification incompatible magnification selected procedure switch the power off then on. The problem continues. Y n return to service call procedures. Change parameters and rerun job. 3-972 over number of do...

  • Page 88

    09/03 2-55 dc 3535/2240/1632, wc m24 3-974, 3-975 status indicator raps initial issue 3-974 next document specified manual placement of next document specified procedure manually change documents on platen glass. The problem continues. Y n return to service call procedures. Switch the power off then...

  • Page 89

    09/03 2-56 dc 3535/2240/1632, wc m24 3-980, 3-985 initial issue status indicator raps 3-980 stapler position error the stapler is not available at the specified position. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Re-set the parameters. 3-98...

  • Page 90

    09/03 2-57 dc 3535/2240/1632, wc m24 3-986 status indicator raps initial issue 3-986 print completion error the number of spooled pages does not match the output. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Count the number of prints to ensur...

  • Page 91

    09/03 2-58 dc 3535/2240/1632, wc m24 3-986 initial issue status indicator raps.

  • Page 92

    09/03 2-59 dc 3535/2240/1632, wc m24 4-340 status indicator raps initial issue 4-340 iot ram failure mcu pwb ram test failed. Procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Check the connection between the mcu pwb and the mcu nvm pwb. If the ch...

  • Page 93

    09/03 2-60 dc 3535/2240/1632, wc m24 4-341 initial issue status indicator raps 4-341 iot logic failure mcu pwb cannot detect intlk +5 vdc. Initial actions • check that the waste toner bottle and all four drum cartridges are seated correctly. • check fault history for 9-925 faults. If this fault has ...

  • Page 94

    09/03 2-61 dc 3535/2240/1632, wc m24 4-342, 4-343 status indicator raps initial issue 4-342 flash rom limit failure limit failure of flash rom procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Replace the mcu pwb ( pl 13.1 ). 4-343 iot flash rom r...

  • Page 95

    09/03 2-62 dc 3535/2240/1632, wc m24 4-344, 4-345 initial issue status indicator raps 4-344 iot micro pitch the micro pitch did not occur within the specified time. Procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Replace the mcu pwb ( pl 13.1 )....

  • Page 96

    09/03 2-63 dc 3535/2240/1632, wc m24 4-346 status indicator raps initial issue 4-346 transfer belt home fault the ibt home sensor does not detect the belt home signal. Note: if this fault is declared 3 times in succession, print mode will be disabled. In order to clear this condition, reset nvm loca...

  • Page 97

    09/03 2-64 dc 3535/2240/1632, wc m24 4-347 initial issue status indicator raps 4-347 transfer belt out of position the ibt edge sensor does not sense the transfer belt edge in the correct position. Initial actions check the following: • check that the ibt belt cleaner is not damaged, binding, or inc...

  • Page 98

    09/03 2-65 dc 3535/2240/1632, wc m24 4-348 status indicator raps initial issue 4-348 transfer belt edge not detected the ibt edge sensor cannot sense the transfer belt edge. Initial actions check the following: • check that the ibt belt cleaner is not damaged, binding, or incorrectly assembled. • en...

  • Page 99

    09/03 2-66 dc 3535/2240/1632, wc m24 4-349, 4-358 initial issue status indicator raps 4-349 marking software logic control logic detected a fatal failure in the marking software. Procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Again, switch the ...

  • Page 100

    09/03 2-67 dc 3535/2240/1632, wc m24 4-361 status indicator raps initial issue 4-361 drum motor drum motor failure. Initial actions • remove all drum cartridges. • perform rep 1.6 . Procedure the machine is a dc3535. Y n enter dc330 [004-003] and press start. The drum motor energizes and the drives ...

  • Page 101

    09/03 2-68 dc 3535/2240/1632, wc m24 4-361 initial issue status indicator raps • p/j535 -b4 (+) and gnd (-) • p/j535 -b5 (+) and gnd (-) less than +1 vdc is measured on p/j535-b3,b4 and b5. Y n • check connection between mcu pwb and i/f pwb (p410). • if no problems are found, replace the mcu pwb ( p...

  • Page 102

    09/03 2-69 dc 3535/2240/1632, wc m24 4-361, 4-362 status indicator raps initial issue figure 2 4-361 rap circuit diagram - drum motor (y,m,c) (dc3535) 4-362 iot nvm read write read write at the mcu pwb nvm r/w. Procedure switch the power off, then on. The problem continues. Y n return to service cal...

  • Page 103

    09/03 2-70 dc 3535/2240/1632, wc m24 4-363 initial issue status indicator raps 4-363 k drum motor drum motor k failure. Initial actions • remove all drum cartridges. • perform rep 1.6 . Procedure the machine is a dc3535. Y n enter dc330 [004-006] and press start. Drum motor k energizes. Y n go to fi...

  • Page 104

    09/03 2-71 dc 3535/2240/1632, wc m24 4-363 status indicator raps initial issue • if no problems are found, replace the mcu pwb ( pl 13.1 ). • if the problem persists, replace the i/f pwb ( pl 9.1 ). Figure 1 4-363 rap circuit diagram - drum motor (k) (dc2240/1632) figure 2 4-363 rap circuit diagram ...

  • Page 105

    09/03 2-72 dc 3535/2240/1632, wc m24 4-371, 4-414 initial issue status indicator raps 4-371 iot controller timing failure there is a communication failure between the ess and iot. Procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Check the mcu pwb...

  • Page 106

    09/03 2-73 dc 3535/2240/1632, wc m24 4-415, 4-417 status indicator raps initial issue 4-415 2nd btr unit it is time to replace the 2nd btr unit. Procedure replace the 2nd btr unit ( pl 2.8 ). The problem continues. Y n return to service call procedures. Was the 2nd btr unit hfsi counter reset in dc1...

  • Page 107

    09/03 2-74 dc 3535/2240/1632, wc m24 4-420, 4-421 initial issue status indicator raps 4-420 transfer belt assembly transfer belt assembly end of life. Procedure replace the transfer belt assembly ( pl 5.3 ). The problem continues. Y n return to service call procedures. Was the transfer belt assembly...

  • Page 108

    09/03 2-75 dc 3535/2240/1632, wc m24 4-605 status indicator raps initial issue 4-605 iot nvm corrupt the system detected that the nvm of the iot is empty. Procedure switch the power off, then on. The problem continues. Y n return to service call procedures. Replace the mcu pwb ( pl 13.1 ). Caution c...

  • Page 109

    09/03 2-76 dc 3535/2240/1632, wc m24 4-640 initial issue status indicator raps 4-640 belt walk failure this hidden fault is declared if the dynamic (short term) color-to-color registration exceeds specification while image formation is in progress. Initial actions adjust the color registration ( adj...

  • Page 110

    09/03 2-77 dc 3535/2240/1632, wc m24 4-641 status indicator raps initial issue 4-641 belt edge learn failure this hidden fault is declared if the dynamic (short term) color-to-color registration exceeds specification while edge learning is in progress. Initial actions check the edge of the transfer ...

  • Page 111

    09/03 2-78 dc 3535/2240/1632, wc m24 4-642, 4-650 initial issue status indicator raps 4-642 belt edge check failure this hidden fault is declared if the dynamic (short term) color-to-color registration exceeds specification while edge checking is in progress after power on or interlock actuation. Pr...

  • Page 112

    09/03 2-79 dc 3535/2240/1632, wc m24 4-908 status indicator raps initial issue 4-908 2nd btr life end 2nd btr end of life. Procedure replace the 2nd btr ( pl 2.8 ) ( rep 9.24 ). The problem continues. Y n return to service call procedures. Was the 2nd btr unit hfsi counter reset in dc135 on the pws....

  • Page 113

    09/03 2-80 dc 3535/2240/1632, wc m24 4-908 initial issue status indicator raps.

  • Page 114

    09/03 2-81 dc 3535/2240/1632, wc m24 5-110 status indicator raps initial issue 5-110 registration sensor on the registration sensor did not detect a document within 800 msec. After the feed motor energized. Initial actions • this fault can be caused by the following operator errors: – pulling the do...

  • Page 115

    09/03 2-82 dc 3535/2240/1632, wc m24 5-111 initial issue status indicator raps 5-111 registration sensor off the document did not deactuate the registration sensor within 1000 msec after the dadf belt motor energized. Initial actions this fault can be caused by an operator loading a large quantity o...

  • Page 116

    09/03 2-83 dc 3535/2240/1632, wc m24 5-112 status indicator raps initial issue 5-112 registration sensor inversion the document does not actuate the dadf registration sensor within 1000 msec after the belt motor energized for document inversion. Initial actions this fault can be caused by using docu...

  • Page 117

    09/03 2-84 dc 3535/2240/1632, wc m24 5-113 initial issue status indicator raps 5-113 registration sensor inversion the document does not deactuate the dadf registration sensor 1500 msec after the belt motor energized for document inversion. Initial actions • ensure that the platen belt is properly a...

  • Page 118

    09/03 2-85 dc 3535/2240/1632, wc m24 5-115 status indicator raps initial issue 5-115 exit sensor on the dadf exit sensor does not detect a document 1500 msec after the dadf exit motor energized at document replacement/output. Initial actions • check the customer’s documents to ensure they meet the s...

  • Page 119

    09/03 2-86 dc 3535/2240/1632, wc m24 5-115 initial issue status indicator raps figure 3 dadf control pwb.

  • Page 120

    09/03 2-87 dc 3535/2240/1632, wc m24 5-116 status indicator raps initial issue 5-116 exit sensor off the document does not deactuate the dadf exit sensor after the dadf exit sensor actuated. Initial actions check the customer’s documents to ensure they meet the specification for the dadf. Ensure the...

  • Page 121

    09/03 2-88 dc 3535/2240/1632, wc m24 5-116 initial issue status indicator raps figure 3 dadf control pwb.

  • Page 122

    09/03 2-89 dc 3535/2240/1632, wc m24 5-195 status indicator raps initial issue 5-195 document size mismatch different sized documents are detected in the no mix mode. Initial actions this fault can be caused by the following: • mixed size documents are fed without selecting that option on the ui. • ...

  • Page 123

    09/03 2-90 dc 3535/2240/1632, wc m24 5-274 initial issue status indicator raps 5-274 original size sensor at power on, the dadf registration sensor turns off, and the dadf size sensor 1 or the dadf size sensor 2 turns on (size sensor detection failure) procedure enter dc330 [5-150] and select start....

  • Page 124

    09/03 2-91 dc 3535/2240/1632, wc m24 5-275 status indicator raps initial issue 5-275 dadf ram failure ram failure of the dadf pwb. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Replace the dadf control pwb ( pl 20.3 )..

  • Page 125

    09/03 2-92 dc 3535/2240/1632, wc m24 5-301 initial issue status indicator raps 5-301 top cover interlock open the top cover is open. Procedure manually actuate both dadf top cover interlock switches (front/rear) at the same time. The 5-301 fault is cleared. Y n remove the dadf rear cover ( rep 5.18 ...

  • Page 126

    09/03 2-93 dc 3535/2240/1632, wc m24 5-700 status indicator raps initial issue 5-700 set gate solenoid rap use this rap when directed to troubleshoot problems with the dadf set gate solenoid. Initial actions remove the following: • front cover ( pl 20.1 ) • entrance tray ( pl 20.1 ) • lower chute as...

  • Page 127

    09/03 2-94 dc 3535/2240/1632, wc m24 5-701 initial issue status indicator raps 5-701 feed motor rap use this rap when directed to troubleshoot problems with the feed motor. Initial actions remove the following: • front cover ( pl 20.1 ) • entrance tray ( pl 20.1 ) • lower chute assembly ( rep 5.8 ) ...

  • Page 128

    09/03 2-95 dc 3535/2240/1632, wc m24 5-702 status indicator raps initial issue 5-702 registration sensor rap use this rap when directed to troubleshoot problems with the registration sensor. Initial actions remove the following: • front cover ( pl 20.1 ) • entrance tray ( pl 20.1 ) • lower chute ass...

  • Page 129

    09/03 2-96 dc 3535/2240/1632, wc m24 5-703 initial issue status indicator raps 5-703 dadf belt motor rap use this rap when directed to troubleshoot problems with the dadf belt motor. Initial actions remove the following: • front cover ( pl 20.1 ) • entrance tray ( pl 20.1 ) • lower chute assembly ( ...

  • Page 130

    09/03 2-97 dc 3535/2240/1632, wc m24 5-900, 5-901 status indicator raps initial issue 5-900 document sensor timing one of the following dadf interlocks was opened during dadf operation: • dadf interlock switch ( pl 20.3 ) • top cover interlock switch (front) ( pl 20.2 ) • top cover interlock switch ...

  • Page 131

    09/03 2-98 dc 3535/2240/1632, wc m24 5-902, 5-903 initial issue status indicator raps 5-902 power on registration sensor the registration sensor detected a document when the top cover/platen interlock was closed or power was switched on. Initial actions clean the registration sensor. Ensure there ar...

  • Page 132

    09/03 2-99 dc 3535/2240/1632, wc m24 5-904, 5-940 status indicator raps initial issue 5-904 power on duplex sensor the dadf duplex sensor detected a document when the top cover/platen interlock was closed or power was switched on initial actions clean the duplex sensor. Ensure there are no pieces of...

  • Page 133

    09/03 2-100 dc 3535/2240/1632, wc m24 5-941 initial issue status indicator raps 5-941 document miscount the software detected a document miscount. Procedure rerun the job. 5-941 continues. Y n return to service call procedures. Replace the dadf control pwb ( pl 20.3 )..

  • Page 134

    09/03 2-101 dc 3535/2240/1632, wc m24 6-277 status indicator raps initial issue 6-277 iit/dadf communication communication cannot be established between the iit/ips and the dadf control pwb. Procedure switch on the power. Cr4 on the dadf control pwb illuminates. Y n +5vdc is measured between the dad...

  • Page 135

    09/03 2-102 dc 3535/2240/1632, wc m24 6-300, 6-312 initial issue status indicator raps 6-300 dadf open the dadf was opened during the dadf job. Procedure enter dc330 [006-300] and place a magnet over the platen open switch ( pl 18.4 ). The dis- play changes. Y n remove the platen glass ( rep 6.2 ). ...

  • Page 136

    09/03 2-103 dc 3535/2240/1632, wc m24 6-340, 6-345 status indicator raps initial issue 6-340 ess ram test error at power on, the system detected a iit/ips pwb ram test error. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Replace the iit/ips pwb...

  • Page 137

    09/03 2-104 dc 3535/2240/1632, wc m24 6-355 initial issue status indicator raps 6-355 ips fan the control logic detects an ips fan failure. Procedure enter dc330 [006-014] and select start. The ips fan ( pl 18.4 ) energizes. Y n switch off the power. Remove the platen glass ( rep 6.2 ) and the ips c...

  • Page 138

    09/03 2-105 dc 3535/2240/1632, wc m24 6-360 status indicator raps initial issue 6-360 carriage position a carriage position error was detected. Procedure switch the power off. Remove the platen glass ( rep 6.2 ). Manually move the full rate car- riage. The carriage moves easily. Y n repair as requir...

  • Page 139

    09/03 2-106 dc 3535/2240/1632, wc m24 6-361 initial issue status indicator raps 6-361 scan registration sensor registration sensor failure at carriage initialization. Procedure switch the power off. Remove the platen glass ( rep 6.2 ). Manually move the full rate car- riage. The carriage moves easil...

  • Page 140

    09/03 2-107 dc 3535/2240/1632, wc m24 6-371 status indicator raps initial issue 6-371 exposure lamp open circuit of the lamp was detected. Procedure enter dc330 [006-002]. Press start. The exposure lamp illuminates. Y n switch off the power. Remove the platen glass ( rep 6.2 ) and the ips cover ( pl...

  • Page 141

    09/03 2-108 dc 3535/2240/1632, wc m24 6-372, 6-380 initial issue status indicator raps 6-372 ros polygon motor the control logic has detected a ros motor failure. Procedure enter dc330 [006-031] and select start. +3.3vdc is measured between the mcu pwb p/ j402 (+) and ground (-) y n go to flag 1 . C...

  • Page 142

    09/03 2-109 dc 3535/2240/1632, wc m24 6-381, 6-382 status indicator raps initial issue 6-381 ros sos m length the interval of the ros start-of-scan (m) signals exceeds the specified value. Procedure +5vdc is measured between the mcu pwb p/j401 -b19 (+) and ground (-). Y n replace the mcu pwb ( pl 13...

  • Page 143

    09/03 2-110 dc 3535/2240/1632, wc m24 6-383, 6-385 initial issue status indicator raps 6-383 ros sos k length the interval of the ros start-of-scan (k) signals exceeds the specified value. Procedure +5vdc is measured between the mcu pwb p/j401 -a2 (+) and ground (-). Y n replace the mcu pwb ( pl 13....

  • Page 144

    09/03 2-111 dc 3535/2240/1632, wc m24 6-389 status indicator raps initial issue 6-389 carriage over run right the carriage has overrun at the scan end. Procedure switch the power off. Remove the platen glass ( rep 6.2 ). Manually move the full rate car- riage. The carriage moves easily. Y n repair a...

  • Page 145

    09/03 2-112 dc 3535/2240/1632, wc m24 6-390 initial issue status indicator raps 6-390 carriage over run left the carriage has overrun at the home end. Procedure switch the power off. Remove the platen glass ( rep 6.2 ). Manually move the full rate car- riage. The carriage moves easily. Y n repair as...

  • Page 146

    09/03 2-113 dc 3535/2240/1632, wc m24 6-391 status indicator raps initial issue 6-391 scan initialize motor driver a carriage motor error was detected after initialization was started. Procedure manually move the full rate carriage to the left until it stops. Enter dc330 [006-005] (scan) and select ...

  • Page 147

    09/03 2-114 dc 3535/2240/1632, wc m24 6-391 initial issue status indicator raps.

  • Page 148

    09/03 2-115 dc 3535/2240/1632, wc m24 7-104 status indicator raps initial issue 7-104 tray 1 feed out sensor the tray 1 feed out sensor does not detect paper fed from tray 2, 3, or 4 within the specified time after the takeaway sensor was actuated. Initial actions • check condition and specification...

  • Page 149

    09/03 2-116 dc 3535/2240/1632, wc m24 7-104 initial issue status indicator raps y n replace the tray module pwb ( pl 15.9 ). Replace the takeaway motor 1 ( pl 15.9 ). Check the drives of the takeaway motor 1 (refer to pl 15.9 ) press stop. • ensure that the chutes ( pl 2.3 , pl 15.10 ) are properly ...

  • Page 150

    09/03 2-117 dc 3535/2240/1632, wc m24 7-104 status indicator raps initial issue figure 5 7-104 circuit diagram - takeaway motor 1 3tm.

  • Page 151

    09/03 2-118 dc 3535/2240/1632, wc m24 7-105 initial issue status indicator raps 7-105 tray 1 misfeed the tray 1 feed out sensor does not detect paper after feeding from tray 1. Initial actions • check condition and specification of paper in tray 1. • check the paper path for obstructions. • check fo...

  • Page 152

    09/03 2-119 dc 3535/2240/1632, wc m24 7-110 status indicator raps initial issue 7-110 tray 2 misfeed the takeaway sensor does not detect paper after feeding from tray 2. Initial actions • check condition and specification of paper in tray 2. • check the paper path for obstructions. • check for wear ...

  • Page 153

    09/03 2-120 dc 3535/2240/1632, wc m24 7-110 initial issue status indicator raps y n takeaway motor 1 ( pl 15.9 ) energizes. Y n press stop. +24 vdc is measured between p/j552 -3 and gnd on the tray module pwb. Y n +24 vdc is measured at p/j 555-3 on the tray module pwb. Y n refer to the +24 vdc wire...

  • Page 154

    09/03 2-121 dc 3535/2240/1632, wc m24 7-110 status indicator raps initial issue figure 3 7-110 rap circuit diagram - takeaway motor 1 (ttm) figure 4 7-110 rap circuit diagram - takeaway sensor (3tm) figure 5 7-110 rap circuit diagram - tray 2 feed/lift motor (3tm).

  • Page 155

    09/03 2-122 dc 3535/2240/1632, wc m24 7-110 initial issue status indicator raps figure 6 7-110 rap circuit diagram - takeaway motor 1 (3tm).

  • Page 156

    09/03 2-123 dc 3535/2240/1632, wc m24 7-115 status indicator raps initial issue 7-115 tray 3 misfeed (ttm) the tray 3 feedout sensor does not detect paper after feeding from tray 3. Initial actions • check condition and specification of paper in tray 3. • check the paper path for obstructions. • che...

  • Page 157

    09/03 2-124 dc 3535/2240/1632, wc m24 7-115 initial issue status indicator raps figure 2 7-115 rap circuit diagram - tray 3 feed/lift motor (ttm) figure 3 7-115 rap circuit diagram - takeaway motor 1 (ttm).

  • Page 158

    09/03 2-125 dc 3535/2240/1632, wc m24 7-117 status indicator raps initial issue 7-117 tray 3 misfeed (3tm) the tray 3 feed out sensor does not detect paper after feeding from tray 3. Initial actions • check condition and specification of paper in tray 3. • check the paper path for obstructions. • ch...

  • Page 159

    09/03 2-126 dc 3535/2240/1632, wc m24 7-117 initial issue status indicator raps figure 2 7-117 rap circuit diagram - tray 3 feed/lift motor (3tm) figure 3 7-117 rap circuit diagram - takeaway motor 1 (3tm).

  • Page 160

    09/03 2-127 dc 3535/2240/1632, wc m24 7-119 status indicator raps initial issue 7-119 tray 4 misfeed (ttm) the tray 4 feed out sensor does not detect paper after feeding from tray 4. Initial actions • check condition and specification of paper in tray 4. • check the paper path for obstructions. • ch...

  • Page 161

    09/03 2-128 dc 3535/2240/1632, wc m24 7-119 initial issue status indicator raps figure 2 7-119 rap circuit diagram - tray 4 feed/lift motor (ttm) figure 3 7-119 rap circuit diagram - takeaway motor 2 (ttm).

  • Page 162

    09/03 2-129 dc 3535/2240/1632, wc m24 7-120 status indicator raps initial issue 7-120 tray 4 misfeed (3tm) the tray 4 feed out sensor does not detect paper after feeding from tray 4. Initial actions • check condition and specification of paper in tray 4. • check the paper path for obstructions. • ch...

  • Page 163

    09/03 2-130 dc 3535/2240/1632, wc m24 7-120 initial issue status indicator raps figure 2 7-120 rap circuit diagram - tray 4 feed/lift motor (3tm) figure 3 7-120 rap circuit diagram - takeaway motor 1 (3tm).

  • Page 164

    09/03 2-131 dc 3535/2240/1632, wc m24 7-122 status indicator raps initial issue 7-122 tray 4 opened (ttm) the tray 4 feed out sensor detected paper when tray 4 is pulled out and pushed in during a print. Initial actions • check condition and specification of paper in tray 4. • check the paper path f...

  • Page 165

    09/03 2-132 dc 3535/2240/1632, wc m24 7-250 initial issue status indicator raps 7-250 tray communication communication fault between tray module pwb and mcu pwb. Procedure +5 vdc is measured at p/j541 -9 on the tray module pwb. Y n 0 vdc is measured at p/j541-9 on the tray module pwb. Y n • go to fi...

  • Page 166

    09/03 2-133 dc 3535/2240/1632, wc m24 7-252 status indicator raps initial issue 7-252 out module logic incorrect software data was detected. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Reinstall the software. If the problem continues, replace...

  • Page 167

    09/03 2-134 dc 3535/2240/1632, wc m24 7-270 initial issue status indicator raps 7-270 tray 1 paper size sensor failure an abnormal a/d value was detected by the tray 1 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 1 paper size sensor ( pl 2.1 ) f...

  • Page 168

    09/03 2-135 dc 3535/2240/1632, wc m24 7-271 status indicator raps initial issue 7-271 tray 2 paper size sensor an abnormal ad value was detected by the tray 2 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 2 paper size sensor for damage or incorre...

  • Page 169

    09/03 2-136 dc 3535/2240/1632, wc m24 7-271 initial issue status indicator raps figure 2 7-271 rap circuit diagram - tray 2 paper size sensing.

  • Page 170

    09/03 2-137 dc 3535/2240/1632, wc m24 7-272 status indicator raps initial issue 7-272 tray 3 paper size sensor (3tm) an abnormal ad value was detected by the tray 3 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 3 paper size sensor ( pl 15.1 ) for...

  • Page 171

    09/03 2-138 dc 3535/2240/1632, wc m24 7-273 initial issue status indicator raps 7-273 tray 4 paper size sensor (3tm) an abnormal ad value was detected by the tray 4 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 4 paper size sensor ( pl 15.1 ) for...

  • Page 172

    09/03 2-139 dc 3535/2240/1632, wc m24 7-274 status indicator raps initial issue 7-274 tray 5 paper size sensor failure an abnormal a/d value was detected by the tray 5 paper size sensor. Initial actions check the connectors between the tray 5 paper size sensor and the i/f pwb procedure enter dc140 [...

  • Page 173

    09/03 2-140 dc 3535/2240/1632, wc m24 7-276 initial issue status indicator raps 7-276 tray 3 paper size sensor (ttm) an abnormal a/d value was detected by the tray 3 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 3 paper size sensor ( pl 16.1 ) fo...

  • Page 174

    09/03 2-141 dc 3535/2240/1632, wc m24 7-277 status indicator raps initial issue 7-277 tray 4 paper size sensor (ttm) an abnormal a/d value was detected by the tray 4 paper size sensor. Initial actions • check that the paper size setting is correct. • check the tray 4 paper size sensor ( pl 16.1 ) fo...

  • Page 175

    09/03 2-142 dc 3535/2240/1632, wc m24 7-281 initial issue status indicator raps 7-281 tray 1 lift the tray 1 level sensor does not detect tray lift. Initial actions remove tray 1 from the machine and empty the paper stock, then: • manually turn the gear at the rear of tray 1 to check that the bottom...

  • Page 176

    09/03 2-143 dc 3535/2240/1632, wc m24 7-282 status indicator raps initial issue 7-282 tray 2 lift the tray 2 level sensor does not detect tray lift. Initial actions remove tray 2 from the machine and empty the paper stock, then: • manually turn the gear at the rear of tray 2 to check that the bottom...

  • Page 177

    09/03 2-144 dc 3535/2240/1632, wc m24 7-282 initial issue status indicator raps figure 2 7-282 rap circuit diagram - tray 2 level sensor (ttm) figure 3 7-282 rap circuit diagram - tray 2 feed lift motor (3tm) figure 4 7-282 rap circuit diagram - tray 2 level sensor (3tm).

  • Page 178

    09/03 2-145 dc 3535/2240/1632, wc m24 7-283 status indicator raps initial issue 7-283 tray 3 lift (3tm) the tray 3 level sensor does not detect tray lift. Initial actions remove tray 3 from the machine and empty the paper stock, then: • manually turn the gear at the rear of tray 3 to check that the ...

  • Page 179

    09/03 2-146 dc 3535/2240/1632, wc m24 7-284 initial issue status indicator raps 7-284 tray 4 lift (3tm) the tray 4 level sensor does not detect tray lift. Initial actions remove tray 4 from the machine and empty the paper stock, then: • manually turn the gear at the rear of tray 4 to check that the ...

  • Page 180

    09/03 2-147 dc 3535/2240/1632, wc m24 7-291 status indicator raps initial issue 7-291 tray 3 lift (ttm) the tray 3 level sensor does not detect tray lift. Initial actions pull out tray 3 and empty the paper stock, then: • manually turn the gear on the left side of tray 3 to check that the bottom pla...

  • Page 181

    09/03 2-148 dc 3535/2240/1632, wc m24 7-293 initial issue status indicator raps 7-293 tray 4 lift (ttm) the tray 4 level sensor does not detect tray lift. Initial actions pull out tray 4 and empty the paper stock, then: • manually turn the gear underneath tray 4 to check that the bottom plate moves ...

  • Page 182

    09/03 2-149 dc 3535/2240/1632, wc m24 7-397 status indicator raps initial issue 7-397 all trays lift sensors none of the tray level sensors can be energized. Procedure the machine is equipped with a 3tm. Y n check the dc122 shutdown history. A 7-281 , 7-282 , 7-291 , or 7-293 fault has occurred. Y n...

  • Page 183

    09/03 2-150 dc 3535/2240/1632, wc m24 7-397 initial issue status indicator raps figure 2 7-397 rap circuit diagram +5 vdc to the tray module pwb.

  • Page 184

    09/03 2-151 dc 3535/2240/1632, wc m24 7-930 status indicator raps initial issue 7-930 tray 1 paper size mismatch the paper in tray 1 does not match the paper size selected. Procedure the correct size paper is loaded in tray 1 and the paper guides are set correctly. Y n load the correct size paper. G...

  • Page 185

    09/03 2-152 dc 3535/2240/1632, wc m24 7-931, 7-932 initial issue status indicator raps 7-931 tray 2 paper size mismatch the paper in tray 2 does not match the paper size selected. Procedure the correct size paper is loaded in tray 2 and the paper guides are set correctly. Y n ensure paper guides are...

  • Page 186

    09/03 2-153 dc 3535/2240/1632, wc m24 7-933, 7-935 status indicator raps initial issue 7-933 tray 4 paper size mismatch the paper in tray 4 does not match the paper size selected. Procedure the machine is equipped with a 3tm. Y n the correct size paper is loaded in tray 4 and the paper guides are se...

  • Page 187

    09/03 2-154 dc 3535/2240/1632, wc m24 7-954, 7-959 initial issue status indicator raps 7-954 tray 5 size mismatch (slow scan direction) the paper in the slow scan direction is shorter than the specified paper size. Procedure the correct size paper is loaded in the tray 5. Y n load the correct size p...

  • Page 188

    09/03 2-155 dc 3535/2240/1632, wc m24 7-960, 7-969 status indicator raps initial issue 7-960 tray 5 paper mismatch 2 a different paper type or transparency was detected when plain/heavyweight paper was speci- fied. Initial actions • check that the loaded paper type matches the ui selection. • check ...

  • Page 189

    09/03 2-156 dc 3535/2240/1632, wc m24 7-960, 7-969 initial issue status indicator raps.

  • Page 190

    09/03 2-157 dc 3535/2240/1632, wc m24 8-149 status indicator raps initial issue 8-149 tray 3 takeaway sensor on (3tm) the takeaway sensor does not detect paper fed from tray 3. Initial actions • check condition and specification of paper in tray 3. • check the paper path and sensor area for obstruct...

  • Page 191

    09/03 2-158 dc 3535/2240/1632, wc m24 8-150 initial issue status indicator raps 8-150 tray 4 takeaway sensor on (3tm) the takeaway sensor does not detect paper fed from tray 4. Initial actions • check condition and specification of paper in tray 4. • check the paper path and sensor area for obstruct...

  • Page 192

    09/03 2-159 dc 3535/2240/1632, wc m24 8-151 status indicator raps initial issue 8-151 tray 3 takeaway sensor on (ttm) the takeaway sensor does not detect paper fed from tray 3. Initial actions • check condition and specification of paper in tray 3. • check the paper path and sensor area for obstruct...

  • Page 193

    09/03 2-160 dc 3535/2240/1632, wc m24 8-152 initial issue status indicator raps 8-152 tray 4 takeaway sensor on (ttm) the takeaway sensor does not detect paper fed from tray 4. Initial actions • check condition and specification of paper in tray 4. • check the paper path and sensor area for obstruct...

  • Page 194

    09/03 2-161 dc 3535/2240/1632, wc m24 8-152 status indicator raps initial issue figure 2 8-152 rap circuit diagram - takeaway motor 1 figure 3 8-152 rap circuit diagram - takeaway motor 2.

  • Page 195

    09/03 2-162 dc 3535/2240/1632, wc m24 8-164 initial issue status indicator raps 8-164 pob sensor the pob sensor did not detect paper after the registration clutch energized. Initial actions • check condition and specification of the paper supply. • check for paper on the ibt. • check for obstruction...

  • Page 196

    09/03 2-163 dc 3535/2240/1632, wc m24 8-175 status indicator raps initial issue 8-175 registration sensor on jam tray 5 the registration sensor does not detect paper fed from the msi. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed ...

  • Page 197

    09/03 2-164 dc 3535/2240/1632, wc m24 8-176 initial issue status indicator raps 8-176 registration sensor on jam tray 1-4 the registration sensor does not detect paper fed from tray 1 - 4. Initial actions • ensure customer closes left lower cover ( pl 2.3 ) firmly if dog ears also occur. • check con...

  • Page 198

    09/03 2-165 dc 3535/2240/1632, wc m24 8-180 status indicator raps initial issue 8-180 registration sensor on duplex the registration sensor does not detect paper after a duplex feed. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed p...

  • Page 199

    09/03 2-166 dc 3535/2240/1632, wc m24 8-180 initial issue status indicator raps figure 2 8-180 rap circuit diagram - duplex motor figure 3 8-180 rap circuit diagram - inverter reverse clutch.

  • Page 200

    09/03 2-167 dc 3535/2240/1632, wc m24 8-181 status indicator raps initial issue 8-181 registration sensor on wait sensor the registration sensor does not detect paper after the duplex wait sensor was energized. Initial actions • check condition and specification of the paper supply. • check for obst...

  • Page 201

    09/03 2-168 dc 3535/2240/1632, wc m24 8-181 initial issue status indicator raps figure 2 8-181 rap circuit diagram - duplex wait sensor figure 3 8-181 rap circuit diagram - duplex motor.

  • Page 202

    09/03 2-169 dc 3535/2240/1632, wc m24 8-184 status indicator raps initial issue 8-184 registration sensor off the fuser exit switch did not detect paper after the registration clutch was energized. Initial actions • check condition and specification of the paper supply. • check for obstructions in t...

  • Page 203

    09/03 2-170 dc 3535/2240/1632, wc m24 8-620, 8-622 initial issue status indicator raps 8-620 regicon temp sensor environment sensor not in range. Procedure note: machine operation continues. Status code not displayed on ui. Status code logged in history. Turn the power off. Disconnect the environmen...

  • Page 204

    09/03 2-171 dc 3535/2240/1632, wc m24 8-623, 8-624 status indicator raps initial issue 8-623 regicon data overflow (a2 patch y) at a2 patch detection, the yso correction setting value of either y, m, c, or k exceeds the set- ting range (nvm value 0 to 474). Note: status code not displayed on ui. Mac...

  • Page 205

    09/03 2-172 dc 3535/2240/1632, wc m24 8-625, 8-626 initial issue status indicator raps 8-625 regicon sample block (a1 patch-rear) at a1 (in) patch detection, the number of the sample blocks does not reach the specified num- ber. Note: status code not displayed on ui. Machine operation continues. Pro...

  • Page 206

    09/03 2-173 dc 3535/2240/1632, wc m24 8-627, 8-628 status indicator raps initial issue 8-627 regicon sample lateral (a1 patch-rear) at a1 (in) patch detection, the fast scan scan position of cyan color that is the standard for the rest is incorrect. (against the mob sensor, the center position of th...

  • Page 207

    09/03 2-174 dc 3535/2240/1632, wc m24 8-629, 8-630 initial issue status indicator raps 8-629 regicon skew (patch y) during a1 patch detection, skew deviation for y exceeded tolerance. Note: machine operation continues. Status code not displayed on ui. Status code logged in history. Initial actions c...

  • Page 208

    09/03 2-175 dc 3535/2240/1632, wc m24 8-631, 8-900 status indicator raps initial issue 8-631 regicon skew (patch k) during a1 patch detection, skew deviation for k exceeded tolerance. Note: machine operation continues. Status code not displayed on ui. Status code logged in history. Initial actions c...

  • Page 209

    09/03 2-176 dc 3535/2240/1632, wc m24 8-631, 8-900 initial issue status indicator raps.

  • Page 210

    09/03 2-177 dc 3535/2240/1632, wc m24 9-342 status indicator raps initial issue 9-342 2nd btr contact the 2nd btr did not reach the contact position. Initial actions • clean the 2nd btr retract sensor ( pl 2.9 ) and check for damage. • check the 2nd btr gears ( pl 2.8 ) for breakage. Procedure enter...

  • Page 211

    09/03 2-178 dc 3535/2240/1632, wc m24 9-342 initial issue status indicator raps figure 2 9-342 rap circuit diagram - 2nd btr retract motor.

  • Page 212

    09/03 2-179 dc 3535/2240/1632, wc m24 9-343 status indicator raps initial issue 9-343 2nd btr retract the 2nd btr did not reach the retract position. Initial actions • clean the 2nd btr retract sensor ( pl 2.9 ) and check for damage. • check the 2nd btr gears ( pl 2.8 ) for breakage. Procedure enter...

  • Page 213

    09/03 2-180 dc 3535/2240/1632, wc m24 9-343 initial issue status indicator raps figure 2 9-343 rap circuit diagram - 2nd btr retract motor.

  • Page 214

    09/03 2-181 dc 3535/2240/1632, wc m24 9-348 status indicator raps initial issue 9-348 1st btr contact the 1st btr did not reach the contact position. Initial actions • clean the 1st btr retract sensor ( pl 5.4 ) and check for damage • check the 1st btr worm gear and retract shaft ( pl 5.4 ) for brea...

  • Page 215

    09/03 2-182 dc 3535/2240/1632, wc m24 9-348 initial issue status indicator raps figure 2 9-348 rap circuit diagram - 1st btr retract motor.

  • Page 216

    09/03 2-183 dc 3535/2240/1632, wc m24 9-349 status indicator raps initial issue 9-349 1st btr retract the 1st btr did not reach the retract position. Initial actions • clean the 1st btr retract sensor ( pl 5.4 ) and check for damage. • check the 1st btr worm gear and retract shaft ( pl 5.4 ) for bre...

  • Page 217

    09/03 2-184 dc 3535/2240/1632, wc m24 9-349 initial issue status indicator raps figure 2 9-349 rap circuit diagram - 1st btr retract motor.

  • Page 218

    09/03 2-185 dc 3535/2240/1632, wc m24 9-350 status indicator raps initial issue 9-350 ibt home sensor the ibt home sensor detected the ibt position strip before the ibt belt made a complete rev- olution. Initial actions • ensure that the transfer belt is installed correctly. • clean the ibt home sen...

  • Page 219

    09/03 2-186 dc 3535/2240/1632, wc m24 9-351 initial issue status indicator raps 9-351 drive logic the ibt edge sensor detected that the ibt belt is not tracking correctly. Initial actions • check the ibt edge sensor for damage. Ensure that the actuator is touching the edge of the belt. • check the i...

  • Page 220

    09/03 2-187 dc 3535/2240/1632, wc m24 9-358, 9-360 status indicator raps initial issue 9-358 full toner sensor the full toner sensor detects a full toner condition. Initial actions • ensure that the waste toner cartridge is not full. • check the sensor for toner contamination and foreign substances....

  • Page 221

    09/03 2-188 dc 3535/2240/1632, wc m24 9-361, 9-362 initial issue status indicator raps 9-361 magenta drum cartridge communication a communication failure with magenta drum cartridge was detected. Initial actions check that the magenta drum cartridge is seated correctly. Procedure enter dc330 [009-15...

  • Page 222

    09/03 2-189 dc 3535/2240/1632, wc m24 9-363, 9-380 status indicator raps initial issue 9-363 black drum cartridge communication a communication failure with the black drum cartridge was detected. Initial actions check that the black drum cartridge is seated correctly. Procedure enter dc330 [009-154]...

  • Page 223

    09/03 2-190 dc 3535/2240/1632, wc m24 9-381, 9-382 initial issue status indicator raps 9-381 atc sensor (m) the atc sensor (m) detects a low tc (toner concentration) initial actions • go to the 9-411 rap and verify the correct operation of the magenta dispense motor and the developer motor. • check ...

  • Page 224

    09/03 2-191 dc 3535/2240/1632, wc m24 9-383, 9-390 status indicator raps initial issue 9-383 atc sensor (k) the atc sensor (k) detects an insufficient amount of developer material initial actions • go to the 9-413 rap and verify the correct operation of the black dispense motor and the developer clu...

  • Page 225

    09/03 2-192 dc 3535/2240/1632, wc m24 9-391, 9-392 initial issue status indicator raps 9-391 new toner cartridge (c) the new cartridge detect switch (c) was not engaged to reset the accumulative dispense time nvm value to 0 when a new cartridge was installed. Initial actions • re-install the toner c...

  • Page 226

    09/03 2-193 dc 3535/2240/1632, wc m24 9-393, 9-408 status indicator raps initial issue 9-393 new toner cartridge (y) when a new toner cartridge was installed, the level of the new cartridge detect switch (y) remained l when it should be changed to h by the dispense motor drive. Initial actions • re-...

  • Page 227

    09/03 2-194 dc 3535/2240/1632, wc m24 9-410 initial issue status indicator raps 9-410 toner cartridge (y) near empty the yellow toner cartridge is nearly empty/empty. This fault requires service only if the mes- sage appears before the toner cartridge is depleted. Note: continuous running of high de...

  • Page 228

    09/03 2-195 dc 3535/2240/1632, wc m24 9-410, 9-411 status indicator raps initial issue figure 2 9-410 rap circuit diagram - dc2240/1632 developer motor figure 3 9-410 rap circuit diagram - dc3535 developer motor 9-411 toner cartridge (m) near empty the magenta toner cartridge is nearly empty. This f...

  • Page 229

    09/03 2-196 dc 3535/2240/1632, wc m24 9-411 initial issue status indicator raps y n go to the 9-381 , atc sensor failure rap. After checking that no failures are detected during normal operation, go to call closeout. Enter dc330 [009-014] and press start. The developer motor ( pl 1.1 ) energizes. Y ...

  • Page 230

    09/03 2-197 dc 3535/2240/1632, wc m24 9-412 status indicator raps initial issue 9-412 toner cartridge (c) near empty the cyan toner cartridge is nearly empty/empty. This fault requires service only if the mes- sage appears before the toner cartridge is depleted. Note: continuous running of high dens...

  • Page 231

    09/03 2-198 dc 3535/2240/1632, wc m24 9-412 initial issue status indicator raps figure 2 9-412 rap circuit diagram - dc2240/1632 developer motor figure 3 9-412 rap circuit diagram - dc3535 developer motor.

  • Page 232

    09/03 2-199 dc 3535/2240/1632, wc m24 9-413 status indicator raps initial issue 9-413 toner cartridge (k) near empty the black toner cartridge is nearly empty. This fault requires service only if the message appears before the toner cartridge is depleted. Note: continuous running of high density pri...

  • Page 233

    09/03 2-200 dc 3535/2240/1632, wc m24 9-428, 9-429 initial issue status indicator raps 9-428 change drum cartridge (k) soon the drum cartridge (k) needs to be replaced soon/reached end of life. Procedure replace the black drum cartridge (refer to section 6, machine consumables ). The problem is corr...

  • Page 234

    09/03 2-201 dc 3535/2240/1632, wc m24 9-430, 9-431 status indicator raps initial issue 9-430 change drum cartridge (m) soon the drum cartridge (m) needs to be replaced soon. Procedure replace the magenta drum cartridge (refer to section 6, machine consumables ). The prob- lem is corrected. Y n repla...

  • Page 235

    09/03 2-202 dc 3535/2240/1632, wc m24 9-654 initial issue status indicator raps 9-654 adc sensor the machine logic detected an adc sensor operation failure. Procedure the machine is a dc3535. Y n check adj 9.4 . The fail judgement of the adc sensor is ok. Y n there is +5vdc from p/j536 -a13 on the i...

  • Page 236

    09/03 2-203 dc 3535/2240/1632, wc m24 9-654 status indicator raps initial issue figure 1 9-654 rap circuit diagram - dc2240/1632 adc sensor figure 2 9-654 rap circuit diagram - dc3535 adc sensor.

  • Page 237

    09/03 2-204 dc 3535/2240/1632, wc m24 9-660, 9-661 initial issue status indicator raps 9-660 environment sensor temperature an incorrect value was detected by the environment sensor (temperature). Procedure disconnect p/j255 . There is 1 ohm or less measured between p255-3 and p255-4 on the environm...

  • Page 238

    09/03 2-205 dc 3535/2240/1632, wc m24 9-670, 9-671 status indicator raps initial issue 9-670 new toner cartridge (k) detected the machine logic detected that the toner cartridge has been replaced. This is a message fault only. Procedure switch the power off, then on. The message fault clears. Y n go...

  • Page 239

    09/03 2-206 dc 3535/2240/1632, wc m24 9-672, 9-673 initial issue status indicator raps 9-672 new toner cartridge (m) detected the machine logic detected that the toner cartridge has been replaced. This is a message fault only. Procedure switch the power off, then on. The message fault clears. Y n go...

  • Page 240

    09/03 2-207 dc 3535/2240/1632, wc m24 9-684 status indicator raps initial issue 9-684 adc shutter the machine logic detected an adc shutter operation failure. Procedure the machine is a dc3535. Y n enter dc330 [009-078] and press start. The adc shutter solenoid energized. Y n there is +24vdc from p/...

  • Page 241

    09/03 2-208 dc 3535/2240/1632, wc m24 9-684 initial issue status indicator raps figure 1 9-684 rap circuit diagram - dc2240/1632 adc sensor figure 2 9-684 rap circuit diagram - dc3535 adc sensor.

  • Page 242

    09/03 2-209 dc 3535/2240/1632, wc m24 9-910, 9-911 status indicator raps initial issue 9-910 drum (y) type mismatch drum type mismatch initial actions ensure that the correct drum type is installed. Ensure that nvm loc. 751 -168 is set correctly (80 for xc, xe, dmo). Procedure enter dc330 [009-151],...

  • Page 243

    09/03 2-210 dc 3535/2240/1632, wc m24 9-912, 9-913 initial issue status indicator raps 9-912 drum (c) type mismatch drum type mismatch initial actions ensure that the correct drum type is installed. Ensure that nvm loc. 751 -168 is set correctly (80 for xc, xe, dmo). Procedure enter dc330 [009-153] ...

  • Page 244

    09/03 2-211 dc 3535/2240/1632, wc m24 9-920, 9-921 status indicator raps initial issue 9-920 toner cartridge (y) empty the yellow toner cartridge is empty. This fault requires service only if the message appears before the toner cartridge is depleted. Note: continuous running of high density prints ...

  • Page 245

    09/03 2-212 dc 3535/2240/1632, wc m24 9-922, 9-923 initial issue status indicator raps 9-922 toner cartridge (c) empty the cyan toner cartridge is empty. This fault requires service only if the message appears before the toner cartridge is depleted. Note: continuous running of high density prints ca...

  • Page 246

    09/03 2-213 dc 3535/2240/1632, wc m24 9-924, 9-925 status indicator raps initial issue 9-924 waste toner cartridge full the waste toner cartridge is full. Initial actions replace the waste toner cartridge. Check the full toner sensor for contaminants. Procedure if the problem persists, go to the 9-3...

  • Page 247

    09/03 2-214 dc 3535/2240/1632, wc m24 9-926, 9-927 initial issue status indicator raps 9-926 drum cartridge (k) end of life the drum cartridge (k) needs to be replaced. Procedure replace the black drum cartridge (refer to section 6, machine consumables ). The problem is corrected. Y n replace the mc...

  • Page 248

    09/03 2-215 dc 3535/2240/1632, wc m24 9-928, 9-929 status indicator raps initial issue 9-928 drum cartridge (m) end of life the drum cartridge (m) needs to be replaced. Procedure replace the magenta drum cartridge (refer to section 6, machine consumables ). The prob- lem is corrected. Y n replace th...

  • Page 249

    09/03 2-216 dc 3535/2240/1632, wc m24 9-930, 9-931 initial issue status indicator raps 9-930 black drum cartridge not detected the machine logic detected that black drum cartridge is not installed. Initial actions • ensure black drum cartridge is installed correctly. • switch the power off, then on....

  • Page 250

    09/03 2-217 dc 3535/2240/1632, wc m24 9-932, 9-933 status indicator raps initial issue 9-932 magenta drum cartridge not detected the machine logic detected that magenta drum cartridge is not installed. Initial actions • ensure magenta drum cartridge is installed correctly. • switch the power off, th...

  • Page 251

    09/03 2-218 dc 3535/2240/1632, wc m24 9-932, 9-933 initial issue status indicator raps.

  • Page 252

    09/03 2-219 dc 3535/2240/1632, wc m24 10-110 status indicator raps initial issue 10-110 fuser exit switch on (duplex) the fuser exit switch did not energize. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • clean the fuser ex...

  • Page 253

    09/03 2-220 dc 3535/2240/1632, wc m24 10-111 initial issue status indicator raps 10-111 fuser exit switch off the fuser exit switch did not de-energize. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • clean the fuser exit ro...

  • Page 254

    09/03 2-221 dc 3535/2240/1632, wc m24 10-125 status indicator raps initial issue 10-125 duplex wait sensor on paper did not arrive at the duplex wait sensor within the specified period of time. Initial actions • check condition and specification of the paper supply. • check the paper path for obstru...

  • Page 255

    09/03 2-222 dc 3535/2240/1632, wc m24 10-125 initial issue status indicator raps figure 2 10-125 rap circuit diagram - duplex wait sensor figure 3 10-125 rap circuit diagram - duplex motor.

  • Page 256

    09/03 2-223 dc 3535/2240/1632, wc m24 10-125 status indicator raps initial issue figure 4 10-125 rap circuit diagram - inverter forward clutch figure 5 10-125 rap circuit diagram - inverter reverse clutch.

  • Page 257

    09/03 2-224 dc 3535/2240/1632, wc m24 10-348 initial issue status indicator raps 10-348 main heater over heat the front thermistor detected an overheat condition. Initial actions turn off the power, remove the fuser assembly, and allow it to cool down. Procedure note: if this fault is declared 3 tim...

  • Page 258

    09/03 2-225 dc 3535/2240/1632, wc m24 10-349, 10-350 status indicator raps initial issue 10-349 front thermistor open the machine logic detected an open circuit in the front thermistor. Initial actions turn off the power, remove the fuser assembly, and allow it to cool down. Procedure measure the re...

  • Page 259

    09/03 2-226 dc 3535/2240/1632, wc m24 10-350 initial issue status indicator raps figure 2 10-350 rap circuit diagram - main heater and sub heater.

  • Page 260

    09/03 2-227 dc 3535/2240/1632, wc m24 10-351, 10-352 status indicator raps initial issue 10-351 rear thermistor open the machine logic detected an open circuit in the rear thermistor. Initial actions turn off the power, remove the fuser assembly and allow it to cool down. Procedure measure the resis...

  • Page 261

    09/03 2-228 dc 3535/2240/1632, wc m24 10-352 initial issue status indicator raps figure 1 10-352 rap circuit diagram - front thermistor figure 2 10-352 rap circuit diagram - main heater and sub heater.

  • Page 262

    09/03 2-229 dc 3535/2240/1632, wc m24 10-353 status indicator raps initial issue 10-353 main heater on time the main heater remained on for more than the specified time. Initial actions turn off the power, remove the fuser assembly, and allow it to cool down. Procedure measure the resistance between...

  • Page 263

    09/03 2-230 dc 3535/2240/1632, wc m24 10-353 initial issue status indicator raps figure 2 10-353 rap circuit diagram - main heater and sub heater.

  • Page 264

    09/03 2-231 dc 3535/2240/1632, wc m24 10-354 status indicator raps initial issue 10-354 sub heater warm up the temperature did not reach the ready temperature. Initial actions turn off the power, remove the fuser assembly, and allow it to cool down. Procedure note: if this fault is declared 3 times ...

  • Page 265

    09/03 2-232 dc 3535/2240/1632, wc m24 10-354 initial issue status indicator raps figure 2 10-354 rap circuit diagram - main heater and sub heater.

  • Page 266

    09/03 2-233 dc 3535/2240/1632, wc m24 10-356 status indicator raps initial issue 10-356 sub heater on time the sub heater remained on for more than the specified time. Initial actions turn off the power, remove the fuser assembly, and allow it to cool down. Procedure measure the resistance between p...

  • Page 267

    09/03 2-234 dc 3535/2240/1632, wc m24 10-356 initial issue status indicator raps figure 2 10-356 rap circuit diagram - main heater and sub heater.

  • Page 268

    09/03 2-235 dc 3535/2240/1632, wc m24 10-398 status indicator raps initial issue 10-398 fan lock the machine logic detected a failure of the fuser fan, lvps fan or the rear fan. Procedure enter dc330 [004-050]. Press start. The fuser fan ( pl 8.1 ) revolves at high speed. Y n there is +24 vdc from p...

  • Page 269

    09/03 2-236 dc 3535/2240/1632, wc m24 10-398 initial issue status indicator raps figure 1 10-398 rap circuit diagram - fuser fan figure 2 10-398 rap circuit diagram - dc 2240/1632 rear fan figure 3 10-398 rap circuit diagram - dc 3535 rear fan figure 4 10-398 rap circuit diagram - dc 2240/1632 lvps ...

  • Page 270

    09/03 2-237 dc 3535/2240/1632, wc m24 10-398, 10-420 status indicator raps initial issue figure 5 10-398 rap circuit diagram - dc 3535 lvps fan 10-420 fuser near end of life replace the fuser assembly in x copies. Procedure the fuser assembly was replaced. Y n replace the fuser assembly ( pl 7.2 ) r...

  • Page 271

    09/03 2-238 dc 3535/2240/1632, wc m24 10-421 initial issue status indicator raps 10-421 fuser end of life fuser at end of life. Procedure the fuser assembly was replaced. Y n replace the fuser assembly ( pl 7.2 ). Run the dc135 [954-804]. The initial value is 0. Y n replace the mcu pwb ( pl 13.1 ). ...

  • Page 272

    09/03 2-239 dc 3535/2240/1632, wc m24 12-100 status indicator raps initial issue 12-100 h transport entrance sensor on the h transport entrance sensor does not detect paper after the registration clutch (in iot) energized. Initial actions • check condition and specification of the paper supply. • ch...

  • Page 273

    09/03 2-240 dc 3535/2240/1632, wc m24 12-100 initial issue status indicator raps figure 4 12-100 rap circuit diagram - finisher drive motor figure 5 finisher pwb.

  • Page 274

    09/03 2-241 dc 3535/2240/1632, wc m24 12-102 status indicator raps initial issue 12-102 h transport entrance sensor off paper did not deactuate the h transport entrance sensor. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. •...

  • Page 275

    09/03 2-242 dc 3535/2240/1632, wc m24 12-102 initial issue status indicator raps figure 3 12-102 rap circuit diagram - finisher drive motor.

  • Page 276

    09/03 2-243 dc 3535/2240/1632, wc m24 12-104 status indicator raps initial issue 12-104 h transport exit sensor on the h transport exit sensor did not detect paper within the specific time after the h transport entrance sensor has detected the paper. (the specified time differs depending on the pape...

  • Page 277

    09/03 2-244 dc 3535/2240/1632, wc m24 12-104 initial issue status indicator raps figure 3 12-104 rap circuit diagram - finisher drive motor figure 4 finisher pwb.

  • Page 278

    09/03 2-245 dc 3535/2240/1632, wc m24 12-106 status indicator raps initial issue 12-106 h transport exit sensor off paper did not deactuate the h transport exit sensor. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • clean t...

  • Page 279

    09/03 2-246 dc 3535/2240/1632, wc m24 12-106 initial issue status indicator raps figure 3 12-106 rap circuit diagram - finisher drive motor figure 4 12-106 rap circuit diagram - decurler cam home sensor figure 5 12-106 rap circuit diagram - decurler cam clutch figure 6 finisher pwb.

  • Page 280

    09/03 2-247 dc 3535/2240/1632, wc m24 12-120 status indicator raps initial issue 12-120 compiler entrance sensor on the compiler entrance sensor did not detect paper. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • clean the...

  • Page 281

    09/03 2-248 dc 3535/2240/1632, wc m24 12-122 initial issue status indicator raps 12-122 compiler entrance sensor off paper does not deactuate the compiler entrance sensor. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • clea...

  • Page 282

    09/03 2-249 dc 3535/2240/1632, wc m24 12-170 status indicator raps initial issue 12-170 set eject the compiler paper sensor did not deactuate after the eject motor energized. Initial actions • check condition and specification of the paper supply. • check for obstructions in the paper feed path. • c...

  • Page 283

    09/03 2-250 dc 3535/2240/1632, wc m24 12-170 initial issue status indicator raps figure 3 12-170 rap circuit diagram - eject motor figure 4 finisher pwb.

  • Page 284

    09/03 2-251 dc 3535/2240/1632, wc m24 12-241 status indicator raps initial issue 12-241 staple move sensor on • the staple sensor did not turn on after the stapler moved to the staple position. • the staple sensor did not actuate after the stapler is in position. Initial actions • check for obstruct...

  • Page 285

    09/03 2-252 dc 3535/2240/1632, wc m24 12-241 initial issue status indicator raps figure 3 12-241 rap circuit diagram - staple move motor figure 4 finisher pwb.

  • Page 286

    09/03 2-253 dc 3535/2240/1632, wc m24 12-242 status indicator raps initial issue 12-242 staple move sensor off • the staple move sensor did not turn off after the move to the staple position started. • the staple move sensor turned off after staple position has been fixed. • the staple move sensor d...

  • Page 287

    09/03 2-254 dc 3535/2240/1632, wc m24 12-242 initial issue status indicator raps figure 3 12-242 rap circuit diagram - staple move motor figure 4 finisher pwb.

  • Page 288

    09/03 2-255 dc 3535/2240/1632, wc m24 12-244 status indicator raps initial issue 12-244 staple home sensor the staple head home sensor did not actuate after the stapler motor energized to open the stapler. Procedure enter dc330 [012-207] and press start. Turn the staple motor gear manually to actuat...

  • Page 289

    09/03 2-256 dc 3535/2240/1632, wc m24 12-244 initial issue status indicator raps figure 4 finisher pwb.

  • Page 290

    09/03 2-257 dc 3535/2240/1632, wc m24 12-252 status indicator raps initial issue 12-252 front tamper • with the front tamper home sensor off the front tamper home sensor did not turn on after move to the front tamper home position began. • with the front tamper home sensor on, the front tamper senso...

  • Page 291

    09/03 2-258 dc 3535/2240/1632, wc m24 12-252 initial issue status indicator raps figure 3 12-252 rap circuit diagram - front tamper motor figure 4 finisher pwb.

  • Page 292

    09/03 2-259 dc 3535/2240/1632, wc m24 12-253 status indicator raps initial issue 12-253 rear tamper • with the rear tamper home sensor off the rear tamper home sensor did not turn on within 800ms after move to the rear tamper home position has begun. • with the rear tamper home sensor on: the rear t...

  • Page 293

    09/03 2-260 dc 3535/2240/1632, wc m24 12-253 initial issue status indicator raps figure 4 finisher pwb.

  • Page 294

    09/03 2-261 dc 3535/2240/1632, wc m24 12-254 status indicator raps initial issue 12-254 stacker tray • the stack height sensor did not detect that the tray went down after the stacker tray lowered at initialization. • the stack height sensor did not detect that the tray went up after the stacker mot...

  • Page 295

    09/03 2-262 dc 3535/2240/1632, wc m24 12-254 initial issue status indicator raps figure 3 12-254 rap circuit diagram - stacker motor figure 4 finisher pwb.

  • Page 296

    09/03 2-263 dc 3535/2240/1632, wc m24 12-255 status indicator raps initial issue 12-255 stacker tray upper limit • the system detected that the stacker tray upper limit sensor was turned on after the stacker tray had begun lifting up. • the system detected that the stacker tray upper limit sensor re...

  • Page 297

    09/03 2-264 dc 3535/2240/1632, wc m24 12-255 initial issue status indicator raps figure 3 12-255 rap circuit diagram - stack height sensor figure 4 12-255 rap circuit diagram - stacker motor figure 5 finisher pwb.

  • Page 298

    09/03 2-265 dc 3535/2240/1632, wc m24 12-256 status indicator raps initial issue 12-256 staple front corner sensor on • the stapler front corner sensor does not turn on within 2 sec. After starting to move to front corner. • the stapler front corner sensor remained on when starting to move to front ...

  • Page 299

    09/03 2-266 dc 3535/2240/1632, wc m24 12-256 initial issue status indicator raps figure 3 12-256 rap circuit diagram - stapler move motor figure 4 finisher pwb.

  • Page 300

    09/03 2-267 dc 3535/2240/1632, wc m24 12-257 status indicator raps initial issue 12-257 staple front corner sensor off • the staple front corner sensor does not turn off after the move from front corner has completed. • the staple front corner sensor does not turn off after starting to move from fro...

  • Page 301

    09/03 2-268 dc 3535/2240/1632, wc m24 12-257 initial issue status indicator raps figure 3 12-257 rap circuit diagram - staple move motor figure 4 finisher pwb.

  • Page 302

    09/03 2-269 dc 3535/2240/1632, wc m24 12-260 status indicator raps initial issue 12-260 eject clamp home sensor on the eject clamp home sensor does not turn on after the eject clamp up started. Initial actions • check for obstructions in the clamp area. Procedure remove the rear cover ( pl 17.5 ) an...

  • Page 303

    09/03 2-270 dc 3535/2240/1632, wc m24 12-260 initial issue status indicator raps figure 3 12-260 rap circuit diagram - eject motor figure 4 finisher pwb.

  • Page 304

    09/03 2-271 dc 3535/2240/1632, wc m24 12-262 status indicator raps initial issue 12-262 eject clamp home sensor off the eject clamp home sensor does not turn off within 200ms after the eject clamp down has started. Procedure remove the rear cover ( pl 17.5 ) and the eject clamp home sensor bracket (...

  • Page 305

    09/03 2-272 dc 3535/2240/1632, wc m24 12-262 initial issue status indicator raps figure 3 12-262 rap circuit diagram - eject motor figure 4 finisher pwb.

  • Page 306

    09/03 2-273 dc 3535/2240/1632, wc m24 12-267 status indicator raps initial issue 12-267 decurler the decurler cam home sensor did not actuate after the decurler cam clutch energized. Procedure remove the rear cover ( pl 17.5 ). Enter dc330 [012-217] and press start. Actuate the decurler cam home sen...

  • Page 307

    09/03 2-274 dc 3535/2240/1632, wc m24 12-267 initial issue status indicator raps figure 4 12-267 rap circuit diagram - finisher drive motor figure 5 finisher pwb.

  • Page 308

    09/03 2-275 dc 3535/2240/1632, wc m24 12-281 status indicator raps initial issue 12-281 set clamp the set clamp home sensor does not actuate after the set clamp started operation. Procedure remove the rear cover ( pl 17.5 ). Enter dc330 [012-211] and press start. Actuate the set clamp home sensor ( ...

  • Page 309

    09/03 2-276 dc 3535/2240/1632, wc m24 12-281 initial issue status indicator raps figure 4 12-281 rap circuit diagram - eject motor figure 5 finisher pwb.

  • Page 310

    09/03 2-277 dc 3535/2240/1632, wc m24 12-301 status indicator raps initial issue 12-301 top cover interlock the finisher top cover interlock is open. Procedure cheat the top cover interlock switch ( figure 1 ). 12-301 is cleared. Y n disconnect p/j851 on the finisher pwb. +5 vdc is measured between ...

  • Page 311

    09/03 2-278 dc 3535/2240/1632, wc m24 12-302 initial issue status indicator raps 12-302 front door interlock open the finisher front door interlock is open. Procedure cheat the front door interlock switch ( figure 1 ). 012-302 is cleared. Y n disconnect p/j851 on the finisher pwb. +5 vdc is measured...

  • Page 312

    09/03 2-279 dc 3535/2240/1632, wc m24 12-303 status indicator raps initial issue 12-303 h transport interlock open the h transport interlock sensor detected open. Procedure block the h transport interlock sensor with a sheet of paper ( figure 1 ). 012-303 is cleared. Y n +5 vdc is measured between t...

  • Page 313

    09/03 2-280 dc 3535/2240/1632, wc m24 12-305 initial issue status indicator raps 12-305 docking interlock open the docking interlock is open. Procedure block the docking interlock sensor with a sheet of paper ( figure 1 ). 012-305 is cleared. Y n +5 vdc is measured between the docking interlock sens...

  • Page 314

    09/03 2-281 dc 3535/2240/1632, wc m24 12-305 status indicator raps initial issue figure 3 finisher pwb.

  • Page 315

    09/03 2-282 dc 3535/2240/1632, wc m24 12-350 initial issue status indicator raps 12-350 finisher communication communication cannot be established between the mcu pwb and the finisher pwb. Procedure switch the power off then on. Cr7 on the finisher pwb is lit. Y n +24 vdc is measured between p/j844 ...

  • Page 316

    09/03 2-283 dc 3535/2240/1632, wc m24 12-399 status indicator raps initial issue 12-399 staple mode logic stapling cannot be selected for the size of paper in the tray. Procedure job can be reprogrammed with different staple setting or paper size. Y n redesign job. Reprogram job..

  • Page 317

    09/03 2-284 dc 3535/2240/1632, wc m24 12-901 initial issue status indicator raps 12-901 power on h transport entrance sensor the h transport entrance sensor detected a paper at power on, when all the interlock were closed, or at initialization. Procedure enter dc330 [012-103] and press start. Actuat...

  • Page 318

    09/03 2-285 dc 3535/2240/1632, wc m24 12-902 status indicator raps initial issue 12-902 power on h transport exit sensor the h transport exit sensor detected a paper at power on, when all the interlock were closed, or at initialization. Procedure enter dc330 [012-104] and press start. Actuate the h ...

  • Page 319

    09/03 2-286 dc 3535/2240/1632, wc m24 12-903 initial issue status indicator raps 12-903 power on compiler entrance sensor the compiler entrance sensor detected a paper at power on, when all the interlocks are closed, or at initialization. Procedure enter dc330 [012-101] and press start. Actuate the ...

  • Page 320

    09/03 2-287 dc 3535/2240/1632, wc m24 12-904 status indicator raps initial issue 12-904 power on compiler paper sensor • the compiler paper sensor continues to detect paper when the paper was output auto- matically due to the power on initialization. • the compiler paper sensor detected paper with n...

  • Page 321

    09/03 2-288 dc 3535/2240/1632, wc m24 12-910 initial issue status indicator raps 12-910 staple feed ready • at the staple preparation operation at initialization, the staple ready sensor does not go to ready (l) status after 13 ready attempts. • the stapler ready sensor is turned off (h) just before...

  • Page 322

    09/03 2-289 dc 3535/2240/1632, wc m24 12-910 status indicator raps initial issue figure 3 finisher pwb.

  • Page 323

    09/03 2-290 dc 3535/2240/1632, wc m24 12-911 initial issue status indicator raps 12-911 stacker lower safety warning the height alignment was not successful during stacker tray lowering while stacking. Initial actions check the stack height sensor actuator for disengagement, bending, obstruction and...

  • Page 324

    09/03 2-291 dc 3535/2240/1632, wc m24 12-914 status indicator raps initial issue 12-914 stacker tray staple set the staple set count of the stacker tray exceeded 50 sets at the staple set eject operation. Initial actions check the actuator of the stacker paper sensor for smooth operation ( figure 1 ...

  • Page 325

    09/03 2-292 dc 3535/2240/1632, wc m24 12-916 initial issue status indicator raps 12-916 stapling the staple head home sensor turned on by the open operation while the sensor failed to turn on (stapling was not available due to an error) after the staple head began to close. Procedure position paper ...

  • Page 326

    09/03 2-293 dc 3535/2240/1632, wc m24 12-916 status indicator raps initial issue figure 3 finisher pwb.

  • Page 327

    09/03 2-294 dc 3535/2240/1632, wc m24 12-960 initial issue status indicator raps 12-960 stacker tray full stack • the system detected small size paper full during the stacker tray height adjustment operation during lowering. • the system detected small size paper full during the stacker tray height ...

  • Page 328

    09/03 2-295 dc 3535/2240/1632, wc m24 12-960 status indicator raps initial issue figure 3 12-960 rap circuit diagram - stack b sensor figure 4 12-960 rap circuit diagram - stacker paper sensor figure 5 12-960 rap circuit diagram - stacker motor figure 6 finisher pwb.

  • Page 329

    09/03 2-296 dc 3535/2240/1632, wc m24 12-961 initial issue status indicator raps 12-961 mix full stack • compared to the maximum paper size that was loaded at the previous job, the paper size (either feed direction or width direction) of the next job is bigger. • staple mode has been changed while t...

  • Page 330

    09/03 2-297 dc 3535/2240/1632, wc m24 12-961 status indicator raps initial issue figure 3 12-961 rap circuit diagram - stack b sensor figure 4 12-961 rap circuit diagram - stacker paper sensor figure 5 12-961 rap circuit diagram - stacker motor figure 6 finisher pwb.

  • Page 331

    09/03 2-298 dc 3535/2240/1632, wc m24 12-965 initial issue status indicator raps 12-965 staple near empty • the low staple switch detected low staple at power on and interlock close. • the low staple switch detected low staple at staple head close. Procedure install a new staple cartridge loaded wit...

  • Page 332

    09/03 2-299 dc 3535/2240/1632, wc m24 12-966 status indicator raps initial issue 12-966 scratch sheet compile paper is output to the compiler that is not part of a print or copy job. Procedure clear the sheets in the stacker tray. The problem continues. Y n return to service call procedures. Rerun t...

  • Page 333

    09/03 2-300 dc 3535/2240/1632, wc m24 12-969 initial issue status indicator raps 12-969 iot top tray full the top tray full sensor has detected full status for 10 sec. Procedure enter dc330 [012-215] and press start. Position some paper near the top tray full sensor ( figure 1 ), then move the paper...

  • Page 334

    09/03 2-301 dc 3535/2240/1632, wc m24 15-362, 15-367 status indicator raps initial issue 15-362 x hard failure communication failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Check the connectors on the iit/ips pwb ( pl 18.3 ). If the chec...

  • Page 335

    09/03 2-302 dc 3535/2240/1632, wc m24 15-370, 15-371 initial issue status indicator raps 15-370 x pio initialization failure 1 communication failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Check the connectors on the iit/ips pwb ( pl 18....

  • Page 336

    09/03 2-303 dc 3535/2240/1632, wc m24 15-372, 15-375 status indicator raps initial issue 15-372 x pio initialization failure 3 communication failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Check the connectors on the iit/ips pwb ( pl 18....

  • Page 337

    09/03 2-304 dc 3535/2240/1632, wc m24 15-376, 15-377 initial issue status indicator raps 15-376 x pio non-match failure 1 communication failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Check the connectors on the iit/ips pwb ( pl 18.3 ) a...

  • Page 338

    09/03 2-305 dc 3535/2240/1632, wc m24 15-380 status indicator raps initial issue 15-380 ccd agc automatic gain control (agc) for ccd channel 1 red failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure switch the po...

  • Page 339

    09/03 2-306 dc 3535/2240/1632, wc m24 15-380 initial issue status indicator raps figure 3 15-380 rap circuit diagram - ccd.

  • Page 340

    09/03 2-307 dc 3535/2240/1632, wc m24 15-381 status indicator raps initial issue 15-381 ccd agc automatic gain control (agc) for ccd channel 2 red failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [...

  • Page 341

    09/03 2-308 dc 3535/2240/1632, wc m24 15-381 initial issue status indicator raps figure 3 15-381 rap circuit diagram - ccd.

  • Page 342

    09/03 2-309 dc 3535/2240/1632, wc m24 15-382 status indicator raps initial issue 15-382 ccd agc automatic gain control (agc) for ccd channel 3 green failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330...

  • Page 343

    09/03 2-310 dc 3535/2240/1632, wc m24 15-382 initial issue status indicator raps figure 3 15-382 rap circuit diagram - ccd.

  • Page 344

    09/03 2-311 dc 3535/2240/1632, wc m24 15-383 status indicator raps initial issue 15-383 ccd agc automatic gain control (agc) for ccd channel 4 green failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330...

  • Page 345

    09/03 2-312 dc 3535/2240/1632, wc m24 15-383 initial issue status indicator raps figure 3 15-383 rap circuit diagram - ccd.

  • Page 346

    09/03 2-313 dc 3535/2240/1632, wc m24 15-384 status indicator raps initial issue 15-384 ccd agc automatic gain control (agc) for ccd channel 5 blue failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 ...

  • Page 347

    09/03 2-314 dc 3535/2240/1632, wc m24 15-384 initial issue status indicator raps figure 3 15-384 rap circuit diagram - ccd.

  • Page 348

    09/03 2-315 dc 3535/2240/1632, wc m24 15-385 status indicator raps initial issue 15-385 ccd agc automatic gain control (agc) for ccd channel 6 blue failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 ...

  • Page 349

    09/03 2-316 dc 3535/2240/1632, wc m24 15-385 initial issue status indicator raps figure 3 15-385 rap circuit diagram - ccd.

  • Page 350

    09/03 2-317 dc 3535/2240/1632, wc m24 15-386 status indicator raps initial issue 15-386 ccd aoc1 automatic offset control (aoc) for ccd channel 1 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [6...

  • Page 351

    09/03 2-318 dc 3535/2240/1632, wc m24 15-387 initial issue status indicator raps 15-387 ccd aoc2 automatic offset control (aoc) for ccd channel 21 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [...

  • Page 352

    09/03 2-319 dc 3535/2240/1632, wc m24 15-388 status indicator raps initial issue 15-388 ccd aoc3 automatic offset control (aoc) for ccd channel 3 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [6...

  • Page 353

    09/03 2-320 dc 3535/2240/1632, wc m24 15-389 initial issue status indicator raps 15-389 ccd aoc4 automatic offset control (aoc) for ccd channel 4 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [6...

  • Page 354

    09/03 2-321 dc 3535/2240/1632, wc m24 15-390 status indicator raps initial issue 15-390 ccd aoc5 automatic offset control (aoc) for ccd channel 5 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [6...

  • Page 355

    09/03 2-322 dc 3535/2240/1632, wc m24 15-391 initial issue status indicator raps 15-391 ccd aoc6 automatic offset control (aoc) for ccd channel 6 failed. Initial actions • verify that the platen glass is installed correctly ( rep 6.2 ). • verify that nvm location 715-400 = 1 procedure enter dc330 [6...

  • Page 356

    09/03 2-323 dc 3535/2240/1632, wc m24 15-790 status indicator raps initial issue 15-790 x detail failure communication failure. Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Check the connectors on the iit/ips pwb ( pl 18.3 ). If the check is o...

  • Page 357

    09/03 2-324 dc 3535/2240/1632, wc m24 15-790 initial issue status indicator raps.

  • Page 358

    09/03 2-325 dc 3535/2240/1632, wc m24 16-311, 16-315 status indicator raps initial issue 16-311 scanner scanner not detected during power up. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Check connections between scanner and iot. Service as requir...

  • Page 359

    09/03 2-326 dc 3535/2240/1632, wc m24 16-316, 16-317 initial issue status indicator raps 16-316 page memory page memory not detected. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Check installation of page memory of the scanner. 16-317 page memory...

  • Page 360

    09/03 2-327 dc 3535/2240/1632, wc m24 16-318, 16-361 status indicator raps initial issue 16-318 optional page memory optional page memory error. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Replace optional page memory of the scanner. 16-361 iot/e...

  • Page 361

    09/03 2-328 dc 3535/2240/1632, wc m24 16-362, 16-363 initial issue status indicator raps 16-362 iot/ess communication failure 2 (extprt) ack not received after 2 resends because the sequence number of the message packet is incorrect. Initial actions switch the power off, then on. If the problem cont...

  • Page 362

    09/03 2-329 dc 3535/2240/1632, wc m24 16-364, 16-365 status indicator raps initial issue 16-364 iot/ess communication failure 4 (extprt) ack not received after 2 resends because the message length of the message packet is incor- rect. Initial actions switch the power off, then on. If the problem con...

  • Page 363

    09/03 2-330 dc 3535/2240/1632, wc m24 16-366, 16-367 initial issue status indicator raps 16-366 iot/ess communication failure 6 (extprt) ack not received after 2 resends because a parity error was declared by the iot hardware. Initial actions switch the power off, then on. If the problem continues, ...

  • Page 364

    09/03 2-331 dc 3535/2240/1632, wc m24 16-368, 16-369 status indicator raps initial issue 16-368 iot/ess communication failure 8 (extprt) ack not received after 2 resends because an overrun error was declared by the iot hard- ware. Initial actions switch the power off, then on. If the problem continu...

  • Page 365

    09/03 2-332 dc 3535/2240/1632, wc m24 16-371, 16-372 initial issue status indicator raps 16-371 dfe/ess communication failure 1 incorrect parameter set initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check that the ddi ca...

  • Page 366

    09/03 2-333 dc 3535/2240/1632, wc m24 16-373, 16-374 status indicator raps initial issue 16-373 dfe/ess communication failure 3 ack not received after 2 resends because the packet number of the message packet is incor- rect. Initial actions switch the power off, then on. If the problem continues, ch...

  • Page 367

    09/03 2-334 dc 3535/2240/1632, wc m24 16-375, 16-376 initial issue status indicator raps 16-375 dfe/ess communication failure 5 ack not received after 2 resends because the checksum of the message packet is incorrect. Initial actions switch the power off, then on. If the problem continues, check the...

  • Page 368

    09/03 2-335 dc 3535/2240/1632, wc m24 16-377, 16-378 status indicator raps initial issue 16-377 dfe/ess communication failure 7 ack not received after 2 resends because a framing error was declared by the iot hardware. Initial actions switch the power off, then on. If the problem continues, check th...

  • Page 369

    09/03 2-336 dc 3535/2240/1632, wc m24 16-379, 16-380 initial issue status indicator raps 16-379 dfe/ess communication failure 9 ack not received after 2 resends because an overrun error was declared by the iot hard- ware. Initial actions switch the power off, then on. If the problem continues, check...

  • Page 370

    09/03 2-337 dc 3535/2240/1632, wc m24 16-380, 16-381 status indicator raps initial issue 16-380 dfe/ess communication failure 10 nak-generated sequence number error. Initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check t...

  • Page 371

    09/03 2-338 dc 3535/2240/1632, wc m24 16-382, 16-383 initial issue status indicator raps 16-382 dfe/ess communication failure 12 nak-generated message length error. Initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check th...

  • Page 372

    09/03 2-339 dc 3535/2240/1632, wc m24 16-384, 16-385 status indicator raps initial issue 16-384 dfe/ess communication failure 14 nak-generated parity error. Initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check that the d...

  • Page 373

    09/03 2-340 dc 3535/2240/1632, wc m24 16-386, 16-387 initial issue status indicator raps 16-386 dfe/ess communication failure 16 nak-generated framing error. Initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check that the ...

  • Page 374

    09/03 2-341 dc 3535/2240/1632, wc m24 16-389, 16-390 status indicator raps initial issue 16-389 dfe/ess communication failure 19 nak-generated packet number error. Initial actions switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check tha...

  • Page 375

    09/03 2-342 dc 3535/2240/1632, wc m24 16-399, 16-450 initial issue status indicator raps 16-399 dfe not detected external controller is not connected or is not functioning. Procedure switch the power off, then on. If the problem continues, check the connections at the mcu pwb and the i/f pwb. Check ...

  • Page 376

    09/03 2-343 dc 3535/2240/1632, wc m24 16-452, 16-453 status indicator raps initial issue 16-452 ip address duplicated pc of the same ip address exists on a network. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Change the ip address. 16-453 ip addr...

  • Page 377

    09/03 2-344 dc 3535/2240/1632, wc m24 16-454, 16-460 initial issue status indicator raps 16-454 dynamic dns update dynamic dns update failed. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Again, switch power off then on 16-460 full status detected ...

  • Page 378

    09/03 2-345 dc 3535/2240/1632, wc m24 16-590, 16-591 status indicator raps initial issue 16-590 read error (partition a) a verify error occurred in the hdd partition a at pc-diag operation from pws. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Set...

  • Page 379

    09/03 2-346 dc 3535/2240/1632, wc m24 16-592, 16-593 initial issue status indicator raps 16-592 read error (partition c) a verify error occurred in the hdd partition c at pc-diag operation from pws. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Set...

  • Page 380

    09/03 2-347 dc 3535/2240/1632, wc m24 16-594, 16-595 status indicator raps initial issue 16-594 read error (partition e) a verify error occurred in the hdd partition e at pc-diag operation from pws. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Set...

  • Page 381

    09/03 2-348 dc 3535/2240/1632, wc m24 16-701, 16-702 initial issue status indicator raps 16-701 plw memory an insufficient memory is detected while using the art ex. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Decrease the resolution. Note: decre...

  • Page 382

    09/03 2-349 dc 3535/2240/1632, wc m24 16-703, 16-704 status indicator raps initial issue 16-703 e-mail to invalid box system detected an unopened or invalid mailbox and aborted a job when receiving an email. Procedure switch power off then on. The problem continues. Y n return to service call proced...

  • Page 383

    09/03 2-350 dc 3535/2240/1632, wc m24 16-705, 16-706 initial issue status indicator raps 16-705 security storage without hd registry for secure print has failed because security storage cannot be done due to no hdd available. Procedure switch power off then on. The problem continues. Y n return to s...

  • Page 384

    09/03 2-351 dc 3535/2240/1632, wc m24 16-709, 16-716 status indicator raps initial issue 16-709 plw command an art ex command error has occurred during plw processing. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Cancel the job and execute the com...

  • Page 385

    09/03 2-352 dc 3535/2240/1632, wc m24 16-721, 16-726 initial issue status indicator raps 16-721 other errors an error occurred during printing that is not defined. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Run the same job again to check the er...

  • Page 386

    09/03 2-353 dc 3535/2240/1632, wc m24 16-728, 16-729 status indicator raps initial issue 16-728 tiff data the data contains a tag that is not set in the image file expansion library. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Delete the unsuppor...

  • Page 387

    09/03 2-354 dc 3535/2240/1632, wc m24 16-730, 16-731 initial issue status indicator raps 16-730 art command art iv command invalid. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Delete the unsupported command from the data and retry printing. 16-73...

  • Page 388

    09/03 2-355 dc 3535/2240/1632, wc m24 16-735, 16-737 status indicator raps initial issue 16-735 job template the system tried to output the job template list while the job template was being updated. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Ru...

  • Page 389

    09/03 2-356 dc 3535/2240/1632, wc m24 16-739, 16-740 initial issue status indicator raps 16-739 job template path the specified path of the job template pool server cannot be found. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Set the resource of ...

  • Page 390

    09/03 2-357 dc 3535/2240/1632, wc m24 16-741, 16-742 status indicator raps initial issue 16-741 job template connection cannot connect to the job template pool server. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Connect the cable from the m/c to ...

  • Page 391

    09/03 2-358 dc 3535/2240/1632, wc m24 16-743, 16-744 initial issue status indicator raps 16-743 job template installation job template pool server installation error or job template pool server setting failure procedure switch power off then on. The problem continues. Y n return to service call proc...

  • Page 392

    09/03 2-359 dc 3535/2240/1632, wc m24 16-745, 16-748 status indicator raps initial issue 16-745 job template definition the job template pool server address cannot be solved (the dns address is not set) procedure switch power off then on. The problem continues. Y n return to service call procedures....

  • Page 393

    09/03 2-360 dc 3535/2240/1632, wc m24 16-749, 16-757 initial issue status indicator raps 16-749 xjcl syntax syntax error of the jcl command was detected. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Correct the command. 16-757 auditron user invali...

  • Page 394

    09/03 2-361 dc 3535/2240/1632, wc m24 16-758, 16-759 status indicator raps initial issue 16-758 auditron function an auditron function is disabled. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Consult the account administrator to add a right. Set ...

  • Page 395

    09/03 2-362 dc 3535/2240/1632, wc m24 16-760, 16-761 initial issue status indicator raps 16-760 decomposer error during decompose processing. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Resend the job. The execution environment/data check are req...

  • Page 396

    09/03 2-363 dc 3535/2240/1632, wc m24 16-762, 16-763 status indicator raps initial issue 16-762 decomposer the print language is not installed or an unsupported function (print language, print utility.) was required. The decomposer specified with pjl or auto sw is not installed. Procedure switch pow...

  • Page 397

    09/03 2-364 dc 3535/2240/1632, wc m24 16-764, 16-765 initial issue status indicator raps 16-764 server transmission smtp server connection error, result code: 421/451 procedure switch power off then on. The problem continues. Y n return to service call procedures. Retrieve e-mail in the server hd. R...

  • Page 398

    09/03 2-365 dc 3535/2240/1632, wc m24 16-766, 16-767 status indicator raps initial issue 16-766 server storage smtp server file system has a problem, result code: 552. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Contact the smtp server administra...

  • Page 399

    09/03 2-366 dc 3535/2240/1632, wc m24 16-768, 16-769 initial issue status indicator raps 16-768 mail from command mail from command, sending address incorrect, login error. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Check the settings of the sel...

  • Page 400

    09/03 2-367 dc 3535/2240/1632, wc m24 16-770, 16-771 status indicator raps initial issue 16-770 template processing the system aborted a job due to insufficient hdd capacity at job template processing. Procedure switch power off then on. The problem continues. Y n return to service call procedures. ...

  • Page 401

    09/03 2-368 dc 3535/2240/1632, wc m24 16-772, 16-773 initial issue status indicator raps 16-772 scan data repository the scan data repository address cannot be solved (response to the dns library error) procedure switch power off then on. The problem continues. Y n return to service call procedures....

  • Page 402

    09/03 2-369 dc 3535/2240/1632, wc m24 16-774, 16-775 status indicator raps initial issue 16-774 hdd compression hdd full has occurred when the s-formatter did the compression type conversion of the jbig compressed images into the mh system (partition #1). Procedure switch power off then on. The prob...

  • Page 403

    09/03 2-370 dc 3535/2240/1632, wc m24 16-776, 16-777 initial issue status indicator raps 16-776 image conversion an error has occurred due to other causes than hdd access during image conversion process by s-formatter. Procedure switch power off then on. The problem continues. Y n return to service ...

  • Page 404

    09/03 2-371 dc 3535/2240/1632, wc m24 16-778, 16-779 status indicator raps initial issue 16-778 hdd capacity the insufficient hdd capacity was detected during scanned image conversion process by i- formatter. Procedure switch power off then on. The problem continues. Y n return to service call proce...

  • Page 405

    09/03 2-372 dc 3535/2240/1632, wc m24 16-780, 16-781 initial issue status indicator raps 16-780 hdd access the hdd access error has occurred during scanned image conversion process by i-format- ter. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Rep...

  • Page 406

    09/03 2-373 dc 3535/2240/1632, wc m24 16-782, 16-783 status indicator raps initial issue 16-782 scan server login server login error during scanning. Cannot log in to the server during scan to server file transfer operation. Procedure switch power off then on. The problem continues. Y n return to se...

  • Page 407

    09/03 2-374 dc 3535/2240/1632, wc m24 16-784, 16-785 initial issue status indicator raps 16-784 server write write error at scanning. The server cannot be written to at the scan to server file transfer. Procedure switch power off then on. The problem continues. Y n return to service call procedures....

  • Page 408

    09/03 2-375 dc 3535/2240/1632, wc m24 16-786, 16-787 status indicator raps initial issue 16-786 hdd scan write internal hdd write error at scanning. A temporary file cannot be written to the internal hdd at the scan to server file transfer. Procedure switch power off then on. The problem continues. ...

  • Page 409

    09/03 2-376 dc 3535/2240/1632, wc m24 16-788, 16-793 i/o hd initial issue status indicator raps 16-788 mailbox to pc retrieval failed at scan to pc (via web browser. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Improve the connection status to a n...

  • Page 410

    09/03 2-377 dc 3535/2240/1632, wc m24 16-950, 16-951 status indicator raps initial issue 16-950 tray 1 empty tray 1 empty procedure switch power off then on. Add paper. The problem continues. Y n return to service call procedures. Go to the 3-950 rap. 16-951 tray 2 empty tray 2 empty procedure switc...

  • Page 411

    09/03 2-378 dc 3535/2240/1632, wc m24 16-952, 16-953 initial issue status indicator raps 16-952 tray 3 empty tray 3 empty procedure switch power off then on. Add paper. The problem continues. Y n return to service call procedures. Go to the 3-952 rap. 16-953 tray 4 empty tray 4 empty procedure switc...

  • Page 412

    09/03 2-379 dc 3535/2240/1632, wc m24 16-954, 16-958 status indicator raps initial issue 16-954 tray 5 empty tray 5 empty procedure switch power off then on. Add paper. The problem continues. Y n return to service call procedures. Go to the 3-954 rap. 16-958 tray 5 size tray 5 size mismatch procedur...

  • Page 413

    09/03 2-380 dc 3535/2240/1632, wc m24 16-959, 16-960 initial issue status indicator raps 16-959 tray 1 size tray 1 size mismatch procedure switch power off then on. The problem continues. Y n return to service call procedures. Load proper paper in the tray. If the problem continues, go to the 7-270 ...

  • Page 414

    09/03 2-381 dc 3535/2240/1632, wc m24 16-961, 16-962 status indicator raps initial issue 16-961 tray 3 size tray 3 size mismatch procedure switch power off then on. The problem continues. Y n return to service call procedures. Load proper paper in the tray. If the problem continues, go to the 7-276 ...

  • Page 415

    09/03 2-382 dc 3535/2240/1632, wc m24 16-965, 16-966 initial issue status indicator raps 16-965 ats/aps no paper aps/ats ng no paper. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Add paper. 16-966 ats/aps no destination ats/aps no destination, oth...

  • Page 416

    09/03 2-383 dc 3535/2240/1632, wc m24 16-981, 16-982 status indicator raps initial issue 16-981 full hdd full status was detected at hdd access. Full status was not cleared even during waiting for timing. One or more pages are already stored. Procedure switch power off then on. The problem continues...

  • Page 417

    09/03 2-384 dc 3535/2240/1632, wc m24 16-981, 16-982 initial issue status indicator raps.

  • Page 418

    09/03 2-385 dc 3535/2240/1632, wc m24 17-310, 17-941 status indicator raps initial issue 17-310 network controller software fail fatal error in nc software. Procedure refer to the network controller service documentation. 17-941 tray 1 not in position the network controller reports that tray 1 is no...

  • Page 419

    09/03 2-386 dc 3535/2240/1632, wc m24 17-942, 17-943 initial issue status indicator raps 17-942 tray 2 not in position the network controller reports that tray 2 is not in a ready condition. Procedure check that tray 2 is closed, and that the paper guides are set correctly. If this does not resolve ...

  • Page 420

    09/03 2-387 dc 3535/2240/1632, wc m24 17-944, 17-946 status indicator raps initial issue 17-944 tray 4 not in position the network controller reports that tray 1 is not in a ready condition. Procedure check that tray 4 is closed, and that the paper guides are set correctly. If this does not resolve ...

  • Page 421

    09/03 2-388 dc 3535/2240/1632, wc m24 17-947, 17-948 initial issue status indicator raps 17-947 tray 2 empty the network controller reports tray 2 empty. Procedure load tray 2. If this does not resolve the problem, go to the 3-951 rap 17-948 tray 3 empty the network controller reports tray 3 empty. ...

  • Page 422

    09/03 2-389 dc 3535/2240/1632, wc m24 17-949, 17-950 status indicator raps initial issue 17-949 tray 4 empty the network controller reports tray 4 empty. Procedure load tray 4. If this does not resolve the problem, go to the 3-953 rap 17-950 tray 5 empty the network controller reports tray 5 empty. ...

  • Page 423

    09/03 2-390 dc 3535/2240/1632, wc m24 17-951, 17-952 initial issue status indicator raps 17-951 tray 1 size mismatch the network controller reports that the paper detected in tray 1 does not match the size des- ignated for the print job. Procedure check the paper in tray 1. If it does not match the ...

  • Page 424

    09/03 2-391 dc 3535/2240/1632, wc m24 17-953, 17-954 status indicator raps initial issue 17-953 tray 3 size mismatch the network controller reports that the paper detected in tray 3 does not match the size des- ignated for the print job. Procedure check the paper in tray 3. If it does not match the ...

  • Page 425

    09/03 2-392 dc 3535/2240/1632, wc m24 17-955, 17-960 initial issue status indicator raps 17-955 ats/aps mismatch the network controller reports that, in auto tray select or auto paper select, no paper of the designated size could be located. Procedure check the paper in the trays. Ensure that the co...

  • Page 426

    09/03 2-393 dc 3535/2240/1632, wc m24 17-961, 17-963 status indicator raps initial issue 17-961 incorrect transparency type incorrect type of transparency detected by the ohp sensor. Initial actions • ensure that only approved transparencies (no white strip) are used. • check that the transparencies...

  • Page 427

    09/03 2-394 dc 3535/2240/1632, wc m24 17-965, 17-966 initial issue status indicator raps 17-965 stacker tray full the network controller reports that the stacker tray in the finisher is full. Procedure empty the stacker tray. If the problem continues, go to the 12-960 rap. 17-966 mix full stack the ...

  • Page 428

    09/03 2-395 dc 3535/2240/1632, wc m24 17-967, 17-968 status indicator raps initial issue 17-967staple near empty the network controller reports one of the following conditions: • the low staple switch detected low staple at power on and interlock close. • the low staple switch detected low staple at...

  • Page 429

    09/03 2-396 dc 3535/2240/1632, wc m24 17-969 initial issue status indicator raps 17-969top tray full (finisher) the network controller reports that the top tray full sensor in the h-transport has detected that the iot top tray is full, for longer than 10 sec. Procedure empty the top tray. If the pro...

  • Page 430

    09/03 2-397 dc 3535/2240/1632, wc m24 20-211, 20-212 status indicator raps initial issue 20-211 option slot 1 failure board failure of option slot 1. Procedure switch power off then on. 20-212 option slot 2 failure board failure of option slot 2. Procedure switch power off then on..

  • Page 431

    09/03 2-398 dc 3535/2240/1632, wc m24 20-340, 20-342 initial issue status indicator raps 20-340 fax control parameter invalid procedure switch power off then on. Re-try the fax job 20-342 fax pwb failure procedure switch power off then on. Re-try the fax job.

  • Page 432

    09/03 2-399 dc 3535/2240/1632, wc m24 20-500, 20-501 status indicator raps initial issue 20-500 dial data invalid procedure switch power off then on. Re-try the fax job 20-501 invalid extension request a non-existing extension was dialed. Procedure switch power off then on. Re-try the fax job.

  • Page 433

    09/03 2-400 dc 3535/2240/1632, wc m24 20-502, 20-503 initial issue status indicator raps 20-502 fax parameter error a required parameter (incoming call number, high layer consistency, icm board specification) is not set. Procedure switch power off then on. Re-try the fax job 20-503 fax parameter err...

  • Page 434

    09/03 2-401 dc 3535/2240/1632, wc m24 20-504, 20-505 status indicator raps initial issue 20-504 fax memory full control logic detects insufficient memory space for job. Procedure switch power off then on. Re-try the fax job 20-505 fax memory overrun control logic detects working memory overflow duri...

  • Page 435

    09/03 2-402 dc 3535/2240/1632, wc m24 20-506, 20-507 initial issue status indicator raps 20-506 unsupported function at destination the recipient machine does not have remote sort copy function. Procedure switch power off then on. Re-try the fax job 20-507 password check error password check error o...

  • Page 436

    09/03 2-403 dc 3535/2240/1632, wc m24 20-508, 20-509 status indicator raps initial issue 20-508 dtmf protocol error procedure-cancel signal is sent and communication is stopped. Procedure switch power off then on. Re-try the fax job 20-509 dtmf protocol error command rejection signal is sent and com...

  • Page 437

    09/03 2-404 dc 3535/2240/1632, wc m24 20-510, 20-511 initial issue status indicator raps 20-510 dtmf protocol error command rejection signal is received and communication is stopped. Procedure switch power off then on. Re-try the fax job 20-511 no file transfer ability at destination file transfer f...

  • Page 438

    09/03 2-405 dc 3535/2240/1632, wc m24 20-512, 20-513 status indicator raps initial issue 20-512 endless loop detected infinite loop is detected in remote relay broadcast. Procedure switch power off then on. Re-try the fax job 20-513 receive command error illegal command is received from remote termi...

  • Page 439

    09/03 2-406 dc 3535/2240/1632, wc m24 20-514, 20-515 initial issue status indicator raps 20-514 requested function unsupported remote maintenance function requested by remote terminal is not available. Procedure switch power off then on. Re-try the fax job 20-515 illegal command received dis receive...

  • Page 440

    09/03 2-407 dc 3535/2240/1632, wc m24 20-519, 20-520 status indicator raps initial issue 20-519 destination overflow total requested number of destinations has exceeded the specified limit (full dial request has exceeded 200 terminals). Procedure switch power off then on. Re-try the fax job 20-520 s...

  • Page 441

    09/03 2-408 dc 3535/2240/1632, wc m24 20-522, 20-523 initial issue status indicator raps 20-522 no line available no connected line available for manual communication procedure switch power off then on. Re-try the fax job 20-523 fax service disabled operation is disabled; service cannot be accepted....

  • Page 442

    09/03 2-409 dc 3535/2240/1632, wc m24 20-524, 20-525 status indicator raps initial issue 20-524 unable to cancel operation operation cannot be inhibited as applicable service is operating. Procedure switch power off then on. Re-try the fax job 20-525 chain-link number invalid specified chain-link do...

  • Page 443

    09/03 2-410 dc 3535/2240/1632, wc m24 20-526, 20-527 initial issue status indicator raps 20-526 illegal chain-link number chain-link value is out of scope. Procedure switch power off then on. Re-try the fax job 20-527 dial control error dialing request overflow. Procedure switch power off then on. R...

  • Page 444

    09/03 2-411 dc 3535/2240/1632, wc m24 20-528, 20-529 status indicator raps initial issue 20-528 cannot perform manual send manual communication was requested while dialing. Procedure switch power off then on. Re-try the fax job 20-529 no printable paper size the paper set during polled-data printing...

  • Page 445

    09/03 2-412 dc 3535/2240/1632, wc m24 20-530, 20-700 initial issue status indicator raps 20-530 dtmf i/f time-out operation was not conducted within specified time. Procedure switch power off then on. Re-try the fax job 20-700 gcp locked • (data task nortc ack); • g3 dicep time-out before idle statu...

  • Page 446

    09/03 2-413 dc 3535/2240/1632, wc m24 20-701, 20-702 status indicator raps initial issue 20-701 software reset procedure switch power off then on. Re-try the fax job 20-702 no destination specified unable to initiate call without address specified. Procedure switch power off then on. Re-try the fax ...

  • Page 447

    09/03 2-414 dc 3535/2240/1632, wc m24 20-703, 20-704 initial issue status indicator raps 20-703 d channel link disconnected dl-link open display received, link disconnected from the network. Procedure switch power off then on. Re-try the fax job 20-704 isdn d channel data link error • d channel link...

  • Page 448

    09/03 2-415 dc 3535/2240/1632, wc m24 20-705, 20-706 status indicator raps initial issue 20-705 isdn layer 1 stopped-power on isdn layer 1 deactivated, power supply on. Procedure switch power off then on. Re-try the fax job 20-706 isdn layer 1 stopped-power off isdn layer 1 deactivated, power supply...

  • Page 449

    09/03 2-416 dc 3535/2240/1632, wc m24 20-707, 20-708 initial issue status indicator raps 20-707 frmr received frmr received. Procedure switch power off then on. Re-try the fax job 20-708 illegal frame received n(r) frame received with n(r) error. Procedure switch power off then on. Re-try the fax jo...

  • Page 450

    09/03 2-417 dc 3535/2240/1632, wc m24 20-709, 20-710 status indicator raps initial issue 20-709 illegal frame received illegal frame received. Procedure switch power off then on. Re-try the fax job 20-710 dl link establishment received dl-link establish display received (link set from the network). ...

  • Page 451

    09/03 2-418 dc 3535/2240/1632, wc m24 20-711, 20-712 initial issue status indicator raps 20-711 wait data link establishment time-out time-out during wait status for link establishment; link setting failure; t.200 time-out has occurred n.200 times during wait status of link setting/ re-setting. Proc...

  • Page 452

    09/03 2-419 dc 3535/2240/1632, wc m24 20-713, 20-714 status indicator raps initial issue 20-713 wait call process time-out time-out during wait for calling acceptance (t303 2nd time). Procedure switch power off then on. Re-try the fax job 20-714 wait release time-out time-out during wait for line re...

  • Page 453

    09/03 2-420 dc 3535/2240/1632, wc m24 20-715, 20-716 initial issue status indicator raps 20-715 wait release complete time-out time-out during wait for line release completion (t308 2nd time). Procedure switch power off then on. Re-try the fax job 20-716 connection time-out time-out during wait for ...

  • Page 454

    09/03 2-421 dc 3535/2240/1632, wc m24 20-717, 20-718 status indicator raps initial issue 20-717 resume time-out time-out during wait for restart (t318). Procedure switch power off then on. Re-try the fax job 20-718 normal disconnection disconnection is recovered on receiving status display; normal d...

  • Page 455

    09/03 2-422 dc 3535/2240/1632, wc m24 20-719, 20-720 initial issue status indicator raps 20-719 no channel available no channel available, or channel not usable. Procedure switch power off then on. Re-try the fax job 20-720 guard timeout timeout of 60sec-guard timer: • t.330 timeout (timeout of rece...

  • Page 456

    09/03 2-423 dc 3535/2240/1632, wc m24 20-721, 20-722 status indicator raps initial issue 20-721 format errror upper layer primitive format error, content error. Procedure switch power off then on. Re-try the fax job 20-722 suspension timeout timeout in receiving the suspension check message. Procedu...

  • Page 457

    09/03 2-424 dc 3535/2240/1632, wc m24 20-723, 20-724 initial issue status indicator raps 20-723 no timer assigned no timer assigned. Procedure switch power off then on. Re-try the fax job 20-724 illegal sequence error sequence (unconformity of local terminal id setting). Procedure switch power off t...

  • Page 458

    09/03 2-425 dc 3535/2240/1632, wc m24 20-725, 20-726 status indicator raps initial issue 20-725 l3 task internal error l3 task internal error. Procedure switch power off then on. Re-try the fax job 20-726 hd81501 i/f buffer busy hd81501 i/f buffer busy. Procedure switch power off then on. Re-try the...

  • Page 459

    09/03 2-426 dc 3535/2240/1632, wc m24 20-727, 20-728 initial issue status indicator raps 20-727 no reply no response obtained from task after 3 sec or more from incoming 1300hz. Procedure switch power off then on. Re-try the fax job 20-728 invalid destination call cannot be completed due to dialing ...

  • Page 460

    09/03 2-427 dc 3535/2240/1632, wc m24 20-729, 20-730 status indicator raps initial issue 20-729 disconnected line line disconnected during transmission of in-channel pb. Procedure switch power off then on. Re-try the fax job 20-730 call conflict conflict between outgoing call and incoming call. Proc...

  • Page 461

    09/03 2-428 dc 3535/2240/1632, wc m24 20-731, 20-732 initial issue status indicator raps 20-731 set-up error set-up was disconnected by network. Procedure switch power off then on. Re-try the fax job 20-732 fax network timeout timeout of f-net disconnection monitor. Procedure switch power off then o...

  • Page 462

    09/03 2-429 dc 3535/2240/1632, wc m24 20-733, 20-734 status indicator raps initial issue 20-733 sequence error message incompatible with status of call. Procedure switch power off then on. Re-try the fax job 20-734 hi task internal error hi task internal error. Procedure switch power off then on. Re...

  • Page 463

    09/03 2-430 dc 3535/2240/1632, wc m24 20-735, 20-736 initial issue status indicator raps 20-735 connect only to d channel connection completion received after service of only d channel service. Procedure switch power off then on. Re-try the fax job 20-736 illegal network message incorrect message fr...

  • Page 464

    09/03 2-431 dc 3535/2240/1632, wc m24 20-737, 20-738 status indicator raps initial issue 20-737 incoming call response error no selection for incoming call response. Procedure switch power off then on. Re-try the fax job 20-738 layer 1 start up error timeout while waiting for startup. Procedure swit...

  • Page 465

    09/03 2-432 dc 3535/2240/1632, wc m24 20-739, 20-740 initial issue status indicator raps 20-739 layer 1 not synchronized timeout of synchronization monitor timer. Procedure switch power off then on. Re-try the fax job 20-740 frame transmission error timeout of monitor timer for frame transmission co...

  • Page 466

    09/03 2-433 dc 3535/2240/1632, wc m24 20-741, 20-742 status indicator raps initial issue 20-741 unable to send frame frame transmission disabled (frame transmission retry over). Procedure switch power off then on. Re-try the fax job 20-742 frame send underrun frame transmission underrun detected. Pr...

  • Page 467

    09/03 2-434 dc 3535/2240/1632, wc m24 20-743, 20-744 initial issue status indicator raps 20-743 abnormal frame error at end of frame transmission dma. Procedure switch power off then on. Re-try the fax job 20-744 unacceptable channel unacceptable channel. Procedure switch power off then on. Re-try t...

  • Page 468

    09/03 2-435 dc 3535/2240/1632, wc m24 20-745, 20-746 status indicator raps initial issue 20-745 duplicate call initiation calling initiated for channel which is already set. Procedure switch power off then on. Re-try the fax job 20-746 no channel available no circuit/channel available. Procedure swi...

  • Page 469

    09/03 2-436 dc 3535/2240/1632, wc m24 20-747, 20-748 initial issue status indicator raps 20-747 switching equipment congestion switching equipment congestion. Procedure switch power off then on. Re-try the fax job 20-748 channel not available requested line/channel cannot be used . Procedure switch ...

  • Page 470

    09/03 2-437 dc 3535/2240/1632, wc m24 20-749, 20-750 status indicator raps initial issue 20-749 network congestion error network congestion error. Procedure switch power off then on. Re-try the fax job 20-750 network error network error. Procedure switch power off then on. Re-try the fax job.

  • Page 471

    09/03 2-438 dc 3535/2240/1632, wc m24 20-751, 20-752 initial issue status indicator raps 20-751 temporary network error temporary failure, network out of order. Procedure switch power off then on. Re-try the fax job 20-752 user busy destination terminal busy. Procedure switch power off then on. Re-t...

  • Page 472

    09/03 2-439 dc 3535/2240/1632, wc m24 20-753, 20-754 status indicator raps initial issue 20-753 destination not responding no response from remote user. Procedure switch power off then on. Re-try the fax job 20-754 no response from destination no response during remote user calling. Procedure switch...

  • Page 473

    09/03 2-440 dc 3535/2240/1632, wc m24 20-755, 20-756 initial issue status indicator raps 20-755 call rejected remote terminal rejects communication. Procedure switch power off then on. Re-try the fax job 20-756 destination fault remote terminal in failure. Procedure switch power off then on. Re-try ...

  • Page 474

    09/03 2-441 dc 3535/2240/1632, wc m24 20-757, 20-758 status indicator raps initial issue 20-757 other fault others (normal, semi-normal classes). Procedure switch power off then on. Re-try the fax job 20-758 incorrect destination missing, unassigned, invalid, or incorrect dial number. Procedure swit...

  • Page 475

    09/03 2-442 dc 3535/2240/1632, wc m24 20-759, 20-760 initial issue status indicator raps 20-759 no relay network route no route to specified transit network. Procedure switch power off then on. Re-try the fax job 20-760 no line to destination no route to destination. Procedure switch power off then ...

  • Page 476

    09/03 2-443 dc 3535/2240/1632, wc m24 20-761, 20-762 status indicator raps initial issue 20-761 incorrect destination invalid number format (incomplete number). Procedure switch power off then on. Re-try the fax job 20-762 facility rejected facility rejected. Procedure switch power off then on. Re-t...

  • Page 477

    09/03 2-444 dc 3535/2240/1632, wc m24 20-763, 20-764 initial issue status indicator raps 20-763 communication disallowed communication capability not authorized. Procedure switch power off then on. Re-try the fax job 20-764 capability not configured communication capability presently not available. ...

  • Page 478

    09/03 2-445 dc 3535/2240/1632, wc m24 20-765, 20-766 status indicator raps initial issue 20-765 unspecified service resource unavailable. Request facility not contracted. Procedure switch power off then on. Re-try the fax job 20-766 capability not implemented undefined communication capability is se...

  • Page 479

    09/03 2-446 dc 3535/2240/1632, wc m24 20-767, 20-768 initial issue status indicator raps 20-767 channel type not implemented undefined channel type is selected. Procedure switch power off then on. Re-try the fax job 20-768 restricted digital info. Only restricted digital information is available. Pr...

  • Page 480

    09/03 2-447 dc 3535/2240/1632, wc m24 20-769, 20-771 status indicator raps initial issue 20-769 unspecified service service not implemented, requested facility not implemented. Procedure switch power off then on. Re-try the fax job 20-771 access information discarded access information discarded. Pr...

  • Page 481

    09/03 2-448 dc 3535/2240/1632, wc m24 20-772, 20-773 initial issue status indicator raps 20-772 unspecified inter-working connection error. Procedure switch power off then on. Re-try the fax job 20-773 invalid dial number invalid call number is used. Procedure switch power off then on. Re-try the fa...

  • Page 482

    09/03 2-449 dc 3535/2240/1632, wc m24 20-774, 20-775 status indicator raps initial issue 20-774 invalid line specified invalid channel number is used. Identified channel does not exist. Procedure switch power off then on. Re-try the fax job 20-775 invalid message class invalid message class. Procedu...

  • Page 483

    09/03 2-450 dc 3535/2240/1632, wc m24 20-776, 20-777 initial issue status indicator raps 20-776 insufficient required info. Mandatory information element is missing. Procedure switch power off then on. Re-try the fax job 20-777 undefined message type message type not available or not implemented. Pr...

  • Page 484

    09/03 2-451 dc 3535/2240/1632, wc m24 20-778, 20-779 status indicator raps initial issue 20-778 incorrect message or type call status and message are not identical, or message type is not defined. Procedure switch power off then on. Re-try the fax job 20-779 no information information element not av...

  • Page 485

    09/03 2-452 dc 3535/2240/1632, wc m24 20-780, 20-781 initial issue status indicator raps 20-780 invalid information invalid information element. Procedure switch power off then on. Re-try the fax job 20-781 call status/message mismatch message not compatible with call status. Procedure switch power ...

  • Page 486

    09/03 2-453 dc 3535/2240/1632, wc m24 20-782, 20-783 status indicator raps initial issue 20-782 recovery by timeout error cleared due to timeout. Procedure switch power off then on. Re-try the fax job 20-783 protocol error unspecified protocol error. Procedure switch power off then on. Re-try the fa...

  • Page 487

    09/03 2-454 dc 3535/2240/1632, wc m24 20-784, 20-785 initial issue status indicator raps 20-784 destination number changed remote terminal number changed. Initial actions check the phone number of the remote machine and transmit again. Procedure switch power off then on. Re-try the fax job note: cus...

  • Page 488

    09/03 2-455 dc 3535/2240/1632, wc m24 20-786, 20-787 status indicator raps initial issue 20-786 call identity not in use disconnection call identity number not in use is specified. Procedure switch power off then on. Re-try the fax job 20-787 call identity in use disconnection call identity number c...

  • Page 489

    09/03 2-456 dc 3535/2240/1632, wc m24 20-788, 20-789 initial issue status indicator raps 20-788 other causes display other causes procedure switch power off then on. Re-try the fax job 20-789 cg conversion timeout g4 presentation has received illegal event. Procedure switch power off then on. Re-try...

  • Page 490

    09/03 2-457 dc 3535/2240/1632, wc m24 20-790, 20-791 status indicator raps initial issue 20-790 line 1 not connected channel 1 external line is not connected. Procedure switch power off then on. Re-try the fax job 20-791 line 0 (extension) not connected channel 1 internal line is not connected. Proc...

  • Page 491

    09/03 2-458 dc 3535/2240/1632, wc m24 20-792, 20-793 initial issue status indicator raps 20-792 channel 2 not connected channel 2 not connected. Procedure switch power off then on. Re-try the fax job 20-793 channel 3 not connected channel 3 not connected. Procedure switch power off then on. Re-try t...

  • Page 492

    09/03 2-459 dc 3535/2240/1632, wc m24 20-794, 20-795 status indicator raps initial issue 20-794 channel 4 not connected channel 4 not connected. Procedure switch power off then on. Re-try the fax job 20-795 channel 5 not connected channel 5 not connected. Procedure switch power off then on. Re-try t...

  • Page 493

    09/03 2-460 dc 3535/2240/1632, wc m24 20-796, 20-797 initial issue status indicator raps 20-796 dial error incorrect fax number. Initial actions check the phone number of the remote machine and transmit again. Procedure switch power off then on. Re-try the fax job note: customers using g3 dp (dial p...

  • Page 494

    09/03 2-461 dc 3535/2240/1632, wc m24 20-798, 20-799 status indicator raps initial issue 20-798 data parameter error job error - communication data parameter has error. Procedure switch power off then on. Re-try the fax job 20-799 auto dial error auto dial is activated without dial data procedure sw...

  • Page 495

    09/03 2-462 dc 3535/2240/1632, wc m24 20-798, 20-799 initial issue status indicator raps.

  • Page 496

    09/03 2-463 dc 3535/2240/1632, wc m24 021-360 status indicator raps initial issue 021-360 foreign device failure the foreign device (3rd-party device such as vend station or mechanical auditron) failed its internal self-test, or the self-test result has not been returned from the foreign device at p...

  • Page 497

    09/03 2-464 dc 3535/2240/1632, wc m24 021-360 initial issue status indicator raps.

  • Page 498

    09/03 2-465 dc 3535/2240/1632, wc m24 33-340, 33-341 status indicator raps initial issue 33-340 fax parameter invalid parameter value is not appropriate (such as excessive length). Procedure switch power off then on. Re-try the fax job 33-341 fax parameter value invalid parameter value exceeds the s...

  • Page 499

    09/03 2-466 dc 3535/2240/1632, wc m24 33-342, 33-343 initial issue status indicator raps 33-342 fax read error designated data invalid (incorrect number or channel etc.) procedure switch power off then on. Re-try the fax job replace fax pwb pl 9.4 33-343 fax read error- invalid data data read error ...

  • Page 500

    09/03 2-467 dc 3535/2240/1632, wc m24 33-350, 33-351 status indicator raps initial issue 33-350 usb open failure usb open failure at initialization. Procedure switch power off then on. Re-try the fax job replace: • fax i/f pwb pl 13.1 • fax pwb pl 9.4 • usb cable pl 9.4 33-351 usb device fatal error...

  • Page 501

    09/03 2-468 dc 3535/2240/1632, wc m24 33-352, 33-353 initial issue status indicator raps 33-352 usb host fatal error usb host fatal error procedure switch power off then on. Re-try the fax job replace: • fax i/f pwb pl 13.1 • fax pwb pl 9.4 • usb cable pl 9.4 33-353 fax manager memory low fax manage...

  • Page 502

    09/03 2-469 dc 3535/2240/1632, wc m24 33-354, 33-354 status indicator raps initial issue 33-354 message library memory low fax message library short of memory procedure switch power off then on. Re-try the fax job 33-354 working memory low memory required for processing cannot be secured due to insu...

  • Page 503

    09/03 2-470 dc 3535/2240/1632, wc m24 33-360, 33-361 initial issue status indicator raps 33-360 fax controller s/w fail a problem in fax software processing prevents further processing. Procedure switch power off then on. Re-try the fax job. If the problem continues reload system software. 33-361 no...

  • Page 504

    09/03 2-471 dc 3535/2240/1632, wc m24 33-362, 33-363 status indicator raps initial issue 33-362 no response fax does not respond within the required period of time. Procedure switch power off then on. Re-try the fax job. If the problem continues replace the fax pwb (pl13.1). 33-363 fax pwb reset fax...

  • Page 505

    09/03 2-472 dc 3535/2240/1632, wc m24 33-364, 33-710 initial issue status indicator raps 33-364 version mismatch software level on fax pwb not compatible with system software procedure switch power off then on. Re-try the fax job. If the problem continues, reload software. 33-710 document error spec...

  • Page 506

    09/03 2-473 dc 3535/2240/1632, wc m24 33-711, 33-712 status indicator raps initial issue 33-711 page error specified page does not exist; or specified page has data error. Procedure switch power off then on. Re-try the fax job. 33-712 host memory full host memory full. Procedure switch power off the...

  • Page 507

    09/03 2-474 dc 3535/2240/1632, wc m24 33-713, 33-714 initial issue status indicator raps 33-713 chain-link fault no specified chain link; applicable chain-link does not exist. Procedure switch power off then on. Re-try the fax job. 33-714 scan error scan error (no specified doc). Data is not registe...

  • Page 508

    09/03 2-475 dc 3535/2240/1632, wc m24 33-715, 33-716 status indicator raps initial issue 33-715 cannot start job host status restriction. Not in the correct state to enable a job operation. Procedure switch power off then on. Re-try the fax job. 33-716 no mailbox specified mailbox does not exist. Pr...

  • Page 509

    09/03 2-476 dc 3535/2240/1632, wc m24 33-717, 33-718 initial issue status indicator raps 33-717 incorrect password verification result of specified password is ng. Procedure switch power off then on. Re-try the fax job. 33-718 no document in mailbox no document exists in polled send box or specified...

  • Page 510

    09/03 2-477 dc 3535/2240/1632, wc m24 33-720, 33-721 status indicator raps initial issue 33-720 document create failure specified document cannot be generated. Procedure switch power off then on. Re-try the fax job. 33-721 page create failure specified page cannot be created. Procedure switch power ...

  • Page 511

    09/03 2-478 dc 3535/2240/1632, wc m24 33-725, 33-726 initial issue status indicator raps 33-725 hard drive full insufficient disk space for fax receiving, formatting, report generating. Procedure switch power off then on. Re-try the fax job. 33-726 duplex print error duplex print is disabled on fax ...

  • Page 512

    09/03 2-479 dc 3535/2240/1632, wc m24 33-727, 33-728 status indicator raps initial issue 33-727 rotation error rotation disabled on fax receive (memory shortage). Procedure switch power off then on. Re-try the fax job. 33-728 auto print canceled fax manual print is input while formatting fax auto pr...

  • Page 513

    09/03 2-480 dc 3535/2240/1632, wc m24 33-730, 33-731 initial issue status indicator raps 33-730 fax recovery error fax job recovery error. Procedure switch power off then on. Re-try the fax job. 33-731 inconsistent instructions communication start from fax pwb and communication stop from controller ...

  • Page 514

    09/03 2-481 dc 3535/2240/1632, wc m24 33-732, 33-733 status indicator raps initial issue 33-732 forced polling receive print job cancelled by forced polling. Procedure switch power off then on. Re-try the fax job. 33-733 document number error cannot obtain the number of documents related to a job. P...

  • Page 515

    09/03 2-482 dc 3535/2240/1632, wc m24 33-734 initial issue status indicator raps 33-734 fax print suspension job stop due to simultaneous starts of fax print and fax auto report. Procedure switch power off then on. Re-try the fax job..

  • Page 516

    09/03 2-483 dc 3535/2240/1632, wc m24 83-700, 83-701 status indicator raps initial issue 83-700 hdlc frame transmission error cs is not off on modem control; procedure switch power off then on. Re-try the fax job. If the problem persists, replace the modem? 83-701 t1 transmission time-out dis is not...

  • Page 517

    09/03 2-484 dc 3535/2240/1632, wc m24 83-702, 83-703 initial issue status indicator raps 83-702 destination receive rejected dcn received for nss/dtc; receiving is rejected due to remote terminal selection receiving, etc. Initial actions the transmission was terminated by the other party. Contact th...

  • Page 518

    09/03 2-485 dc 3535/2240/1632, wc m24 83-704, 83-705 status indicator raps initial issue 83-704 destination polling error no polling function on sender side; polled documents are not set; no sending capability on remote terminal; no sending ability on remote terminal on polling; no stored documents....

  • Page 519

    09/03 2-486 dc 3535/2240/1632, wc m24 83-706, 83-707 initial issue status indicator raps 83-706 fallback error unable to fallback on nss transmission; waiting for auto resend. Procedure switch power off then on. Re-try the fax job 83-707 password error password not identical; or select-receive numbe...

  • Page 520

    09/03 2-487 dc 3535/2240/1632, wc m24 83-708, 83-709 status indicator raps initial issue 83-708 post-message re-transmission error no response to three attempts at post-message command, or dcn received. Procedure switch power off then on. Re-try the fax job line quality no good; receiver failure; sc...

  • Page 521

    09/03 2-488 dc 3535/2240/1632, wc m24 83-710, 83-711 initial issue status indicator raps 83-710 receive pin received pin procedure switch power off then on. Re-try the fax job line quality no good; calling an operator from receiver side; receiver side failure; sc board (modem) failure; ncu board fai...

  • Page 522

    09/03 2-489 dc 3535/2240/1632, wc m24 83-712, 83-713 status indicator raps initial issue 83-712 no nsc response no response after transmitting nsc 3 times procedure switch power off then on. Re-try the fax job incorrect password. No polled document on remote terminal; jam on remote terminal. 83-713 ...

  • Page 523

    09/03 2-490 dc 3535/2240/1632, wc m24 83-714, 83-715 initial issue status indicator raps 83-714 dcn received after nsc/dtc dcn received after transmitting nsc/dtc. Initial actions the transmission was terminated by the other party. Contact the other party and check the sta- tus of the other machine....

  • Page 524

    09/03 2-491 dc 3535/2240/1632, wc m24 83-716, 83-717 status indicator raps initial issue 83-716 post-message t2 time-out t2 time-out on t.30 receiver side timer waiting for command procedure switch power off then on. Re-try the fax job sender side failure; line quality no good; sc board (modem) fail...

  • Page 525

    09/03 2-492 dc 3535/2240/1632, wc m24 83-718, 83-719 initial issue status indicator raps 83-718 receive t1 time-out t1 time-out in receiving at phase b. Procedure switch power off then on. Re-try the fax job 83-719 busy tone busy tone detected at phase b. Procedure re-try the fax job.

  • Page 526

    09/03 2-493 dc 3535/2240/1632, wc m24 83-720, 83-721 status indicator raps initial issue 83-720 remote unable to receive nsf/dis nsc/dtc contents are invalid; no receiving capability on remote terminal. Procedure re-try the fax job 83-721 dcn at phase-b dcn detected at receiving phase b; no compatib...

  • Page 527

    09/03 2-494 dc 3535/2240/1632, wc m24 83-722, 83-723 initial issue status indicator raps 83-722 frame length error frame length has exceeded 3.45 sec. (300bps command / response) procedure remote terminal failure. Re-try the fax job 83-723 cd time-out cd not received within 3 minutes after receiving...

  • Page 528

    09/03 2-495 dc 3535/2240/1632, wc m24 83-724, 83-725 status indicator raps initial issue 83-724 dcn received after ftt dcn received after transmitting ftt. Procedure switch power off then on. Re-try the fax job sender side failure; line quality no good 83-725 no mailbox/relay destination has no mail...

  • Page 529

    09/03 2-496 dc 3535/2240/1632, wc m24 83-726, 83-727 initial issue status indicator raps 83-726 phase c time-out cannot receive phase c training within 10 secs procedure switch power off then on. Re-try the fax job line quality no good; sc board (modem) failure; ncu board failure. 83-727 50% error d...

  • Page 530

    09/03 2-497 dc 3535/2240/1632, wc m24 83-728, 83-729 status indicator raps initial issue 83-728 phase c eol time-out eol cannot be received within 10 sec.; normal line cannot be detected in 1min from the start of receiving image information in g3; eol cannot be detected for 13 sec. (default) while i...

  • Page 531

    09/03 2-498 dc 3535/2240/1632, wc m24 83-730, 83-731 initial issue status indicator raps 83-730 hdlc frame send error modem cs is not turned on in response to rs request during command transmission/high- speed training. Procedure switch power off then on. Re-try the fax job. If the problem persists,...

  • Page 532

    09/03 2-499 dc 3535/2240/1632, wc m24 83-732, 83-733 status indicator raps initial issue 83-732 v.34 pch cd off v.34 pch cd off. Procedure switch power off then on. Re-try the fax job 83-733 no v.34 c/p-ch cs no v.34 c/p-ch cs. Procedure switch power off then on. Re-try the fax job.

  • Page 533

    09/03 2-500 dc 3535/2240/1632, wc m24 83-734, 83-735 initial issue status indicator raps 83-734 polling error remote terminal has no document to be polled with v.8 protocol. Polled send operation was wrong on the remote terminal. Procedure switch power off then on. Re-try the fax job 83-735 no docum...

  • Page 534

    09/03 2-501 dc 3535/2240/1632, wc m24 83-736, 83-737 status indicator raps initial issue 83-736 no response to ctc no response is sent back to ctc transmission, or dcn is received. Procedure switch power off then on. Re-try the fax job (line quality no good; sc board (modem) failure; ncu board failu...

  • Page 535

    09/03 2-502 dc 3535/2240/1632, wc m24 83-738, 83-739 initial issue status indicator raps 83-738 no response to rr no response is sent back to rr transmission, or dcn is received with rr. Procedure switch power off then on. Re-try the fax job. Remote terminal failure. 83-739 t5 time-out t5 sec. Has p...

  • Page 536

    09/03 2-503 dc 3535/2240/1632, wc m24 83-740, 83-741 status indicator raps initial issue 83-740 abort sending after eor sending suspended after eor transmission; eor-q sent in ecm; procedure switch power off then on. Re-try the fax job. Line quality no good; sc board (modem) failure; ncu board failu...

  • Page 537

    09/03 2-504 dc 3535/2240/1632, wc m24 83-742, 83-743 initial issue status indicator raps 83-742 eor send or receive error response sent back with err after ecm eor send; eor-q is received at ecm reception. Procedure switch power off then on. Re-try the fax job. Line quality no good. 83-743 destinati...

  • Page 538

    09/03 2-505 dc 3535/2240/1632, wc m24 83-744, 83-745 status indicator raps initial issue 83-744 destination password error destination has no ability to receive password. Procedure switch power off then on. Re-try the fax job 83-745 destination sep error ptx terminal has no sep ability. Procedure sw...

  • Page 539

    09/03 2-506 dc 3535/2240/1632, wc m24 83-746, 83-747 initial issue status indicator raps 83-746 dial tone error one of the following has occurred: • dial tone cannot be detected before dialing. Dt1 cannot be detected. • busy tone is detected before dialing. Bt1 detected. • busy tone is detected befo...

  • Page 540

    09/03 2-507 dc 3535/2240/1632, wc m24 83-748, 83-749 status indicator raps initial issue 83-748 post-message re-transmission error no response to three attempts at post-message command, or dcn received. Procedure switch power off then on. Re-try the fax job line quality no good; receiver failure; sc...

  • Page 541

    09/03 2-508 dc 3535/2240/1632, wc m24 83-750 , 83-751 initial issue status indicator raps 83-750 power off error power off error during communication. The power switch was turned off, or the system was reset. Procedure re-try the fax job. 83-751 stop key error the stop key was pressed while a docume...

  • Page 542

    09/03 2-509 dc 3535/2240/1632, wc m24 83-752, 83-753 status indicator raps initial issue 83-752 job number limit error limited number of jobs error procedure switch power off then on. Re-try the fax job. 83-753 document image memory full image information memory full (file full, append record error)...

  • Page 543

    09/03 2-510 dc 3535/2240/1632, wc m24 83-754, 83-755 initial issue status indicator raps 83-754 file management area full file management area full procedure switch power off then on. Re-try the fax job. 83-755 file append record error file append record error procedure switch power off then on. Re-...

  • Page 544

    09/03 2-511 dc 3535/2240/1632, wc m24 83-756, 83-757 status indicator raps initial issue 83-756 file no additional data no additional file procedure switch power off then on. Re-try the fax job. 83-757 no received page no received page procedure switch power off then on. Re-try the fax job..

  • Page 545

    09/03 2-512 dc 3535/2240/1632, wc m24 83-758, 83-759 initial issue status indicator raps 83-758 file or page not specified no specified file or page procedure switch power off then on. Re-try the fax job. 83-759 no job error no appropriate job when the communication reservation was cleared. Procedur...

  • Page 546

    09/03 2-513 dc 3535/2240/1632, wc m24 83-760, 83-761 status indicator raps initial issue 83-760 file error invalid file. Time-out has occurred due to the comm file access, or the file handler did not return an error code momentarily when an error occurred. Procedure switch power off then on. Re-try ...

  • Page 547

    09/03 2-514 dc 3535/2240/1632, wc m24 83-762 initial issue status indicator raps 83-762 disconnect during isdn link establishment • the link is disconnected during its establishment. • the line has been disconnected during communication. (error only for isdn) procedure switch power off then on. Re-t...

  • Page 548

    09/03 2-515 dc 3535/2240/1632, wc m24 84-500, 84-501 status indicator raps initial issue 84-500 pdrp illegal parameter rdrp incorrect parameter procedure switch power off then on. Re-try the fax job. 84-501 pdpbp illegal parameter rdrp incorrect parameter procedure switch power off then on. Re-try t...

  • Page 549

    09/03 2-516 dc 3535/2240/1632, wc m24 84-502, 84-503 initial issue status indicator raps 84-502 pdpbn illegal parameter rdpbn incorrect parameter procedure switch power off then on. Re-try the fax job. 84-503 rdclp illegal parameter rdclp incorrect parameter procedure switch power off then on. Re-tr...

  • Page 550

    09/03 2-517 dc 3535/2240/1632, wc m24 84-504, 84-505 status indicator raps initial issue 84-504 rdclp illegal parameter rdgr incorrect parameter procedure switch power off then on. Re-try the fax job. 84-505 undefined response undefined response procedure switch power off then on. Re-try the fax job...

  • Page 551

    09/03 2-518 dc 3535/2240/1632, wc m24 84-506, 84-507 initial issue status indicator raps 84-506 negotiation disabled negotiation not available procedure switch power off then on. Re-try the fax job. 84-507 receive capability limit rdpbp received (receive capability limit) no record paper at the dest...

  • Page 552

    09/03 2-519 dc 3535/2240/1632, wc m24 84-508, 84-509 status indicator raps initial issue 84-508 terminal error rdpbn received. (terminal failure) procedure switch power off then on. Re-try the fax job. 84-509 unspecified error rdpbn received. Unspecified error (other than terminal failure). Procedur...

  • Page 553

    09/03 2-520 dc 3535/2240/1632, wc m24 84-510, 84-511 initial issue status indicator raps 84-510 received rdgr rdgr received. Procedure switch power off then on. Re-try the fax job. 84-511 illegal procedure incorrect procedure procedure switch power off then on. Re-try the fax job..

  • Page 554

    09/03 2-521 dc 3535/2240/1632, wc m24 84-512, 84-513 status indicator raps initial issue 84-512 cds illegal parameter cds incorrect parameter procedure switch power off then on. Re-try the fax job. 84-513 cdc illegal parameter cdc incorrect parameter procedure switch power off then on. Re-try the fa...

  • Page 555

    09/03 2-522 dc 3535/2240/1632, wc m24 84-514, 84-515 initial issue status indicator raps 84-514 cde illegal parameter cde incorrect parameter procedure switch power off then on. Re-try the fax job. 84-515 cdd illegal parameter cdd incorrect parameter procedure switch power off then on. Re-try the fa...

  • Page 556

    09/03 2-523 dc 3535/2240/1632, wc m24 84-516, 84-517 status indicator raps initial issue 84-516 cdr illegal parameter procedure switch power off then on. Re-try the fax job. 84-517 cdpb illegal parameter procedure switch power off then on. Re-try the fax job..

  • Page 557

    09/03 2-524 dc 3535/2240/1632, wc m24 84-518, 84-519 initial issue status indicator raps 84-518 cdcl illegal parameter procedure switch power off then on. Re-try the fax job. 84-519 undefined command procedure switch power off then on. Re-try the fax job..

  • Page 558

    09/03 2-525 dc 3535/2240/1632, wc m24 84-520, 84-521 status indicator raps initial issue 84-520 negotiation not available negotiation not available (cds indicating fax feature mismatch was received). Procedure switch power off then on. Re-try the fax job. 84-521 negotiation not available negotiation...

  • Page 559

    09/03 2-526 dc 3535/2240/1632, wc m24 84-522, 84-523 initial issue status indicator raps 84-522 terminal error cdd received (terminal failure). Procedure switch power off then on. Re-try the fax job. 84-523 unspecified error cdd received (other than terminal failure). Procedure switch power off then...

  • Page 560

    09/03 2-527 dc 3535/2240/1632, wc m24 84-524, 84-525 status indicator raps initial issue 84-524 terminal error cdr received (terminal failure). Procedure switch power off then on. Re-try the fax job. 84-525 unspecified error cdr received (other than terminal failure). Procedure switch power off then...

  • Page 561

    09/03 2-528 dc 3535/2240/1632, wc m24 84-526, 84-527 initial issue status indicator raps 84-526 cdui illegal parameter cdui incorrect parameter (normal document) procedure switch power off then on. Re-try the fax job. 84-527 cdui illegal parameter cdui incorrect parameter (operator document) procedu...

  • Page 562

    09/03 2-529 dc 3535/2240/1632, wc m24 84-528, 84-529 status indicator raps initial issue 84-528 cdui illegal parameter cdui incorrect parameter (control document) procedure switch power off then on. Re-try the fax job. 84-529 cdui illegal parameter cdui incorrect parameter (monitor document) procedu...

  • Page 563

    09/03 2-530 dc 3535/2240/1632, wc m24 84-530, 84-531 initial issue status indicator raps 84-530 illegal document cds was received (control document) indicating the mismatch of the recipient/sender of an illegal document. Procedure switch power off then on. Re-try the fax job. 84-531 dma channel 1 ab...

  • Page 564

    09/03 2-531 dc 3535/2240/1632, wc m24 84-532, 84-533 status indicator raps initial issue 84-532 dma channel 2 abnormal end procedure switch power off then on. Re-try the fax job. 84-533 data conversion error data conversion resource acquisition not available. Procedure switch power off then on. Re-t...

  • Page 565

    09/03 2-532 dc 3535/2240/1632, wc m24 84-534, 84-535 initial issue status indicator raps 84-534 decode error decoding failure while data conversion in progress, procedure switch power off then on. Re-try the fax job. 84-535 data conversion error while data conversion was in progress, white line tran...

  • Page 566

    09/03 2-533 dc 3535/2240/1632, wc m24 84-536, 84-537 status indicator raps initial issue 84-536 data conversion error while data conversion was in progress, white line transfer error to the decode dicep occurred. Procedure switch power off then on. Re-try the fax job. 84-537 data conversion error wh...

  • Page 567

    09/03 2-534 dc 3535/2240/1632, wc m24 84-538, 84-539 initial issue status indicator raps 84-538 document descriptor analysis error procedure switch power off then on. Re-try the fax job. 84-539 page descriptor analysis error procedure switch power off then on. Re-try the fax job..

  • Page 568

    09/03 2-535 dc 3535/2240/1632, wc m24 84-540, 84-541 status indicator raps initial issue 84-540 text unit analysis error procedure switch power off then on. Re-try the fax job. 84-541 no text unit page boundary without tu was received. Procedure switch power off then on. Re-try the fax job..

  • Page 569

    09/03 2-536 dc 3535/2240/1632, wc m24 84-701, 84-702 initial issue status indicator raps 84-701 receive status error receive status variable n (r) error procedure switch power off then on. Re-try the fax job. 84-702 ni over information frame size over (ni over) procedure switch power off then on. Re...

  • Page 570

    09/03 2-537 dc 3535/2240/1632, wc m24 84-703, 84-704 status indicator raps initial issue 84-703 supervisory/un-numbered frame error procedure switch power off then on. Re-try the fax job. 84-704 undefined command/response procedure switch power off then on. Re-try the fax job..

  • Page 571

    09/03 2-538 dc 3535/2240/1632, wc m24 84-705 , 84-709 initial issue status indicator raps 84-705 receive confirmation time-out successive time-out of the receive check timer (n2 time-out) procedure switch power off then on. Re-try the fax job. 84-709 forced link termination forced termination of the...

  • Page 572

    09/03 2-539 dc 3535/2240/1632, wc m24 84-710, 84-711 status indicator raps initial issue 84-710 receive frmr (z=1) procedure switch power off then on. Re-try the fax job. 84-711 receive frmr (y=1) procedure switch power off then on. Re-try the fax job..

  • Page 573

    09/03 2-540 dc 3535/2240/1632, wc m24 84-712, 84-713 initial issue status indicator raps 84-712 receive frmr (x=1) procedure switch power off then on. Re-try the fax job. 84-713 receive frmr (w=1) procedure switch power off then on. Re-try the fax job..

  • Page 574

    09/03 2-541 dc 3535/2240/1632, wc m24 84-714, 84-716 status indicator raps initial issue 84-714 received global address procedure switch power off then on. Re-try the fax job. 84-716 transmit busy time-out lsi transmit error (sending busy, time-out) procedure switch power off then on. Re-try the fax...

  • Page 575

    09/03 2-542 dc 3535/2240/1632, wc m24 84-717, 84-718 initial issue status indicator raps 84-717 illegal action lsi operation error procedure switch power off then on. Re-try the fax job. 84-718 wait disconnect time-out time-out while waiting for notification of disconnection (10sec.) procedure switc...

  • Page 576

    09/03 2-543 dc 3535/2240/1632, wc m24 84-719, 84-720 status indicator raps initial issue 84-719 c-line on error line c was turned on, but line i was not. Procedure switch power off then on. Re-try the fax job. 84-720 c-line off error line c was turned off, but line i was not. Procedure switch power ...

  • Page 577

    09/03 2-544 dc 3535/2240/1632, wc m24 84-721, 84-722 initial issue status indicator raps 84-721 i-line off error during communication, the line i was turned off. Procedure switch power off then on. Re-try the fax job. 84-722 disconnected call calling was disconnected during detection of the flag fro...

  • Page 578

    09/03 2-545 dc 3535/2240/1632, wc m24 84-723 , 84-724 status indicator raps initial issue 84-723 disconnected call after sending sabm, calling was disconnected at wait time for ua. Procedure switch power off then on. Re-try the fax job. 84-724 disconnected call calling was disconnected at wait time ...

  • Page 579

    09/03 2-546 dc 3535/2240/1632, wc m24 84-725 , 84-726 initial issue status indicator raps 84-725 disconnected call disc was received before the session was established. Procedure switch power off then on. Re-try the fax job. 84-726 illegal header illegal header received (line switching), incorrect p...

  • Page 580

    09/03 2-547 dc 3535/2240/1632, wc m24 84-727, 84-728 status indicator raps initial issue 84-727 illegal parameter - cc packet procedure switch power off then on. Re-try the fax job. 84-728 illegal parameter - cn packet procedure switch power off then on. Re-try the fax job..

  • Page 581

    09/03 2-548 dc 3535/2240/1632, wc m24 84-729, 84-730 initial issue status indicator raps 84-729 illegal parameter - dt packet procedure switch power off then on. Re-try the fax job. 84-730 illegal parameter - ri packet procedure switch power off then on. Re-try the fax job..

  • Page 582

    09/03 2-549 dc 3535/2240/1632, wc m24 84-731, 84-732 status indicator raps initial issue 84-731 illegal parameter - it packet procedure switch power off then on. Re-try the fax job. 84-732 illegal parameter - ci packet procedure switch power off then on. Re-try the fax job..

  • Page 583

    09/03 2-550 dc 3535/2240/1632, wc m24 84-733, 84-734 initial issue status indicator raps 84-733 illegal parameter - cf packet procedure switch power off then on. Re-try the fax job. 84-734 undefined packet received procedure switch power off then on. Re-try the fax job..

  • Page 584

    09/03 2-551 dc 3535/2240/1632, wc m24 84-735, 84-736 status indicator raps initial issue 84-735 wait cc time-out procedure switch power off then on. Re-try the fax job. 84-736 wait cf time-out procedure switch power off then on. Re-try the fax job..

  • Page 585

    09/03 2-552 dc 3535/2240/1632, wc m24 84-738, 84-739 initial issue status indicator raps 84-738 dt packet error p (s), p (r) error in the dt packet procedure switch power off then on. Re-try the fax job. 84-739 rr/rnr packet error p (s) error in the rr or rnr packet procedure switch power off then o...

  • Page 586

    09/03 2-553 dc 3535/2240/1632, wc m24 84-740, 84-741 status indicator raps initial issue 84-740 busy time-out procedure switch power off then on. Re-try the fax job. 84-741 receive si error si received during communication procedure switch power off then on. Re-try the fax job..

  • Page 587

    09/03 2-554 dc 3535/2240/1632, wc m24 84-742, 84-743 initial issue status indicator raps 84-742 receive sf error sf received during communication procedure switch power off then on. Re-try the fax job. 84-743 d-bit error in dt packet procedure switch power off then on. Re-try the fax job..

  • Page 588

    09/03 2-555 dc 3535/2240/1632, wc m24 84-747, 84-748 status indicator raps initial issue 84-747 receive fast select fast select receive that limits the responses. Procedure switch power off then on. Re-try the fax job. 84-748 remote charge request received procedure switch power off then on. Re-try ...

  • Page 589

    09/03 2-556 dc 3535/2240/1632, wc m24 84-749, 84-750 initial issue status indicator raps 84-749 lcgn error procedure switch power off then on. Re-try the fax job. 84-750 illegal procedure procedure switch power off then on. Re-try the fax job..

  • Page 590

    09/03 2-557 dc 3535/2240/1632, wc m24 84-751, 84-752 status indicator raps initial issue 84-751 illegal parameter - tca procedure switch power off then on. Re-try the fax job. 84-752 illegal parameter - tcr procedure switch power off then on. Re-try the fax job..

  • Page 591

    09/03 2-558 dc 3535/2240/1632, wc m24 84-753, 84-754 initial issue status indicator raps 84-753 illegal parameter - tcc procedure switch power off then on. Re-try the fax job. 84-754 illegal parameter - tbr procedure switch power off then on. Re-try the fax job..

  • Page 592

    09/03 2-559 dc 3535/2240/1632, wc m24 84-755, 84-756 status indicator raps initial issue 84-755 illegal parameter - tdt procedure switch power off then on. Re-try the fax job. 84-756 undefined transport block received procedure switch power off then on. Re-try the fax job..

  • Page 593

    09/03 2-560 dc 3535/2240/1632, wc m24 84-757, 84-758 initial issue status indicator raps 84-757 wait tca time-out procedure switch power off then on. Re-try the fax job. 84-758 wait tcr time-out procedure switch power off then on. Re-try the fax job..

  • Page 594

    09/03 2-561 dc 3535/2240/1632, wc m24 84-759, 84-760 status indicator raps initial issue 84-759 wait tcc time-out procedure switch power off then on. Re-try the fax job. 84-760 wait tbr time-out procedure switch power off then on. Re-try the fax job..

  • Page 595

    09/03 2-562 dc 3535/2240/1632, wc m24 84-761, 84-763 initial issue status indicator raps 84-761 tdt block size error procedure switch power off then on. Re-try the fax job. 84-763 illegal procedure procedure switch power off then on. Re-try the fax job..

  • Page 596

    09/03 2-563 dc 3535/2240/1632, wc m24 84-764, 84-765 status indicator raps initial issue 84-764 illegal parameter - css procedure switch power off then on. Re-try the fax job. 84-765 illegal parameter - cse procedure switch power off then on. Re-try the fax job..

  • Page 597

    09/03 2-564 dc 3535/2240/1632, wc m24 84-766, 84-767 initial issue status indicator raps 84-766 illegal parameter - csa procedure switch power off then on. Re-try the fax job. 84-767 illegal parameter - csui procedure switch power off then on. Re-try the fax job..

  • Page 598

    09/03 2-565 dc 3535/2240/1632, wc m24 84-768, 84-769 status indicator raps initial issue 84-768 illegal parameter - cscc procedure switch power off then on. Re-try the fax job. 84-769 illegal parameter - rssp procedure switch power off then on. Re-try the fax job..

  • Page 599

    09/03 2-566 dc 3535/2240/1632, wc m24 84-770, 84-771 initial issue status indicator raps 84-770 illegal parameter - rssn procedure switch power off then on. Re-try the fax job. 84-771 illegal parameter - rsep procedure switch power off then on. Re-try the fax job..

  • Page 600

    09/03 2-567 dc 3535/2240/1632, wc m24 84-772, 84-773 status indicator raps initial issue 84-772 illegal parameter - rsap procedure switch power off then on. Re-try the fax job. 84-773 illegal parameter - rsui procedure switch power off then on. Re-try the fax job..

  • Page 601

    09/03 2-568 dc 3535/2240/1632, wc m24 84-774, 84-775 initial issue status indicator raps 84-774 illegal parameter - rsccp procedure switch power off then on. Re-try the fax job. 84-775 undefined command/response procedure switch power off then on. Re-try the fax job..

  • Page 602

    09/03 2-569 dc 3535/2240/1632, wc m24 84-776, 84-777 status indicator raps initial issue 84-776 received rssn procedure switch power off then on. Re-try the fax job. 84-777 wait disconnect time-out time-out after waiting for notification of disconnection (10sec) procedure switch power off then on. R...

  • Page 603

    09/03 2-570 dc 3535/2240/1632, wc m24 84-778, 84-779 initial issue status indicator raps 84-778 terminal error csa received. (terminal failure). Procedure switch power off then on. Re-try the fax job. 84-779 unspecified error csa received (other than terminal failure). Procedure switch power off the...

  • Page 604

    09/03 2-571 dc 3535/2240/1632, wc m24 84-780, 84-781 status indicator raps initial issue 84-780 wait css time-out procedure switch power off then on. Re-try the fax job. 84-781 wait rssp time-out procedure switch power off then on. Re-try the fax job..

  • Page 605

    09/03 2-572 dc 3535/2240/1632, wc m24 84-782, 84-783 initial issue status indicator raps 84-782 wait rsap time-out procedure switch power off then on. Re-try the fax job. 84-783 wait rsep time-out time-out after waiting for rsep procedure switch power off then on. Re-try the fax job..

  • Page 606

    09/03 2-573 dc 3535/2240/1632, wc m24 84-784, 84-785 status indicator raps initial issue 84-784 wait rsccp time-out time-out after waiting for rsccp procedure switch power off then on. Re-try the fax job. 84-785 wait csui/rsui time-out time-out after waiting for csui/rsui procedure switch power off ...

  • Page 607

    09/03 2-574 dc 3535/2240/1632, wc m24 84-786, 84-787 initial issue status indicator raps 84-786 receive rssn (password mismatch) the destination machine returned "mismatch of password" with rssn. Initial actions communication could not take place because the id of the remote machine and the password...

  • Page 608

    09/03 2-575 dc 3535/2240/1632, wc m24 84-788, 84-789 status indicator raps initial issue 84-788 receive rssp (no document) the destination machine returned "no polling sending document" with rssp. Procedure switch power off then on. Re-try the fax job. 84-789 receive rssp (no password) rssp indicati...

  • Page 609

    09/03 2-576 dc 3535/2240/1632, wc m24 84-790, 84-791 initial issue status indicator raps 84-790 receive rssp (sending rights) rssp indicating that sending right is not required was received at polling receive operation. Procedure switch power off then on. Re-try the fax job. 84-791 receive rssn (pas...

  • Page 610

    09/03 2-577 dc 3535/2240/1632, wc m24 84-792, 84-793 status indicator raps initial issue 84-792 received cse after transmitting rssp procedure switch power off then on. Re-try the fax job. 84-793 select communication error procedure switch power off then on. Re-try the fax job..

  • Page 611

    09/03 2-578 dc 3535/2240/1632, wc m24 84-795, 84-796 initial issue status indicator raps 84-795 disconnected call disconnected because the destination machine does not have multi-copying capability. Procedure switch power off then on. Re-try the fax job. 84-796 normal sending alert normal sending wa...

  • Page 612

    09/03 2-579 dc 3535/2240/1632, wc m24 84-797, 84-798 status indicator raps initial issue 84-797 illegal procedure procedure switch power off then on. Re-try the fax job. 84-798 illegal parameter - rdep procedure switch power off then on. Re-try the fax job..

  • Page 613

    09/03 2-580 dc 3535/2240/1632, wc m24 84-799 initial issue status indicator raps 84-799 illegal parameter - rddp procedure switch power off then on. Re-try the fax job..

  • Page 614

    09/03 2-581 dc 3535/2240/1632, wc m24 102-200, 102-201 status indicator raps initial issue 102-200 receive buffer overflow the data received from the controller exceeded the buffer amount of the destination in the panel. Procedure switch power off then on. The problem continues. Y n return to servic...

  • Page 615

    09/03 2-582 dc 3535/2240/1632, wc m24 102-202, 102-203 initial issue status indicator raps 102-202 request queue full the event that requires more than the processing capability for the request arising in the panel has occurred. Procedure switch power off then on. The problem continues. Y n return t...

  • Page 616

    09/03 2-583 dc 3535/2240/1632, wc m24 102-204, 102-205 status indicator raps initial issue 102-204 sio parameter serial communication failure. Incorrect message size at sio receiving request, or incorrect mailbox id when a message is sent. Procedure switch power off then on. The problem continues. Y...

  • Page 617

    09/03 2-584 dc 3535/2240/1632, wc m24 102-206, 102-207 initial issue status indicator raps 102-206 sio status serial communication failure. A header status error of the rx packet or a message status error of the rx packet has occurred. Procedure switch power off then on. The problem continues. Y n r...

  • Page 618

    09/03 2-585 dc 3535/2240/1632, wc m24 102-208, 102-209 status indicator raps initial issue 102-208 communication manager command serial communication failure. A command error has occurred when receiving from sio. Procedure switch power off then on. The problem continues. Y n return to service call p...

  • Page 619

    09/03 2-586 dc 3535/2240/1632, wc m24 102-310, 102-311 initial issue status indicator raps 102-310 send queue full over the upper limit of the processing capability to send data from the panel to the controller. Procedure switch power off then on. The problem continues. Y n return to service call pr...

  • Page 620

    09/03 2-587 dc 3535/2240/1632, wc m24 102-312, 102-313 status indicator raps initial issue 102-312 evm uses wrong api illegal use of api by evm. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-313 as uses ...

  • Page 621

    09/03 2-588 dc 3535/2240/1632, wc m24 102-314, 102-315 initial issue status indicator raps 102-314 wait event time out time-out of the event waiting timer. The response message from the controller was not noti- fied for a specified time. Procedure switch power off then on. The problem continues. Y n...

  • Page 622

    09/03 2-589 dc 3535/2240/1632, wc m24 102-316, 102-317 status indicator raps initial issue 102-316 send request queue full sio over the upper limit of the processing capability to send data from the panel to the controller. Procedure switch power off then on. The problem continues. Y n return to ser...

  • Page 623

    09/03 2-590 dc 3535/2240/1632, wc m24 102-318, 102-319 initial issue status indicator raps 102-318 receive finish queue full the data received from the controller exceeded the upper limit of the processing capability in the panel. Procedure switch power off then on. The problem continues. Y n return...

  • Page 624

    09/03 2-591 dc 3535/2240/1632, wc m24 102-320, 102-321 status indicator raps initial issue 102-320 polling serial communication failure. Communication failure (polling error) procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of ...

  • Page 625

    09/03 2-592 dc 3535/2240/1632, wc m24 102-322, 102-323 initial issue status indicator raps 102-322 target serial communication failure. Target error. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-323 add...

  • Page 626

    09/03 2-593 dc 3535/2240/1632, wc m24 102-324, 102-325 status indicator raps initial issue 102-324 size serial communication failure. Size error procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-325 object c...

  • Page 627

    09/03 2-594 dc 3535/2240/1632, wc m24 102-326, 102-327 initial issue status indicator raps 102-326 memory overflow memory overflow. The memory in the guam exceeded the upper limit. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Expand the memory in ...

  • Page 628

    09/03 2-595 dc 3535/2240/1632, wc m24 102-328, 102-329 status indicator raps initial issue 102-328 ui internal with out of area i/f failure in the ui. The coordination value out of the area of the displayed screen was detected (w x h = 640 x 240) procedure switch power off then on. The problem conti...

  • Page 629

    09/03 2-596 dc 3535/2240/1632, wc m24 102-330, 102-331 initial issue status indicator raps 102-330 interface with invalid parameter lcd interface failure. Incorrect parameter was detected at the drv. I/f between the dm and lcd. Procedure switch power off then on. The problem continues. Y n return to...

  • Page 630

    09/03 2-597 dc 3535/2240/1632, wc m24 102-332, 102-333 status indicator raps initial issue 102-332 interface with invalid parameter cp interface failure. Incorrect parameter was detected at the drv. I/f between the dm and cp. Procedure switch power off then on. The problem continues. Y n return to s...

  • Page 631

    09/03 2-598 dc 3535/2240/1632, wc m24 102-334, 102-335 initial issue status indicator raps 102-334 interface with receiving error key code interface failure. Invalid key code was received from the control panel. Procedure switch power off then on. The problem continues. Y n return to service call pr...

  • Page 632

    09/03 2-599 dc 3535/2240/1632, wc m24 102-336, 102-337 status indicator raps initial issue 102-336 interface dm - acd drv. I/f interface failure. Incorrect parameter was detected at the drv. I/f between the dm and acd. Procedure switch power off then on. The problem continues. Y n return to service ...

  • Page 633

    09/03 2-600 dc 3535/2240/1632, wc m24 102-338, 102-339 initial issue status indicator raps 102-338 frame data error offset address out of scope invalid frame data was detected. The offset address out of range was extracted from the frame id. Procedure switch power off then on. The problem continues....

  • Page 634

    09/03 2-601 dc 3535/2240/1632, wc m24 102-340, 102-341 status indicator raps initial issue 102-340 interface guam - dm i/f interface failure. Incorrect parameter was detected at the i/f between the guam and dm. Procedure switch power off then on. The problem continues. Y n return to service call pro...

  • Page 635

    09/03 2-602 dc 3535/2240/1632, wc m24 102-342, 102-343 initial issue status indicator raps 102-342 event queue empty event queue empty procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, ...

  • Page 636

    09/03 2-603 dc 3535/2240/1632, wc m24 102-344, 102-345 status indicator raps initial issue 102-344 invalid type invalid type procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace th...

  • Page 637

    09/03 2-604 dc 3535/2240/1632, wc m24 102-346, 102-347 initial issue status indicator raps 102-346 invalid timer number invalid timer number procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem conti...

  • Page 638

    09/03 2-605 dc 3535/2240/1632, wc m24 102-348, 102-349 status indicator raps initial issue 102-348 command access exception exceptional command access procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the pro...

  • Page 639

    09/03 2-606 dc 3535/2240/1632, wc m24 102-350, 102-351 initial issue status indicator raps 102-350 privilege command privilege command procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, ...

  • Page 640

    09/03 2-607 dc 3535/2240/1632, wc m24 102-352, 102-353 status indicator raps initial issue 102-352 address alignment address mis-alignment procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continu...

  • Page 641

    09/03 2-608 dc 3535/2240/1632, wc m24 102-354, 102-355 initial issue status indicator raps 102-354 tag overflow tag overflow procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace th...

  • Page 642

    09/03 2-609 dc 3535/2240/1632, wc m24 102-356, 102-357 status indicator raps initial issue 102-356 short of area insufficient area procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, repl...

  • Page 643

    09/03 2-610 dc 3535/2240/1632, wc m24 102-358, 102-359 initial issue status indicator raps 102-358 time out time-out procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace the contro...

  • Page 644

    09/03 2-611 dc 3535/2240/1632, wc m24 102-360, 102-361 status indicator raps initial issue 102-360 context context error procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace the co...

  • Page 645

    09/03 2-612 dc 3535/2240/1632, wc m24 102-362, 102-363 initial issue status indicator raps 102-362 no object object non-existence procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, repla...

  • Page 646

    09/03 2-613 dc 3535/2240/1632, wc m24 102-364, 102-365 status indicator raps initial issue 102-364 parameter parameter error procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace th...

  • Page 647

    09/03 2-614 dc 3535/2240/1632, wc m24 102-366, 102-367 initial issue status indicator raps 102-366 reserve function code code number for reserve function procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the ...

  • Page 648

    09/03 2-615 dc 3535/2240/1632, wc m24 102-368, 102-369 status indicator raps initial issue 102-368 short of ui memory insufficient memory, or connection failure procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. ...

  • Page 649

    09/03 2-616 dc 3535/2240/1632, wc m24 102-370, 102-371 initial issue status indicator raps 102-370 interface length interface length failure. The parameter notified from the controller was incorrect. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Pe...

  • Page 650

    09/03 2-617 dc 3535/2240/1632, wc m24 102-372, 102-373 status indicator raps initial issue 102-372 interface sequence interface sequence failure. The initial command from the controller was not notified within a specified time. Initial actions • switch power off then on. • remove and reseat the nvm ...

  • Page 651

    09/03 2-618 dc 3535/2240/1632, wc m24 102-374, 102-375 initial issue status indicator raps 102-374 invalid user job id incorrect user job id. The job id parameter notified from the controller was incorrect. Procedure switch power off then on. The problem continues. Y n return to service call procedu...

  • Page 652

    09/03 2-619 dc 3535/2240/1632, wc m24 102-376, 102-377 status indicator raps initial issue 102-376 internal memory internal memory failure. Panel-sw failure. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102...

  • Page 653

    09/03 2-620 dc 3535/2240/1632, wc m24 102-378, 102-379 initial issue status indicator raps 102-378 interface format interface format failure. The data format notified from the controller was incorrect. Procedure switch power off then on. The problem continues. Y n return to service call procedures. ...

  • Page 654

    09/03 2-621 dc 3535/2240/1632, wc m24 102-380, 102-382 status indicator raps initial issue 102-380 copy interface copy interface failure procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-382 scanner interfac...

  • Page 655

    09/03 2-622 dc 3535/2240/1632, wc m24 102-383, 102-384 initial issue status indicator raps 102-383 report interface report interface failure procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-384 server acces...

  • Page 656

    09/03 2-623 dc 3535/2240/1632, wc m24 102-385, 102-386 status indicator raps initial issue 102-385 service object overflow service object overflow procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-386 invali...

  • Page 657

    09/03 2-624 dc 3535/2240/1632, wc m24 102-387, 102-388 initial issue status indicator raps 102-387 invalid service object attribute invalid service object attribute procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the softwa...

  • Page 658

    09/03 2-625 dc 3535/2240/1632, wc m24 102-389, 102-390 status indicator raps initial issue 102-389 argument argument error procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-390 job parameter job parameter ar...

  • Page 659

    09/03 2-626 dc 3535/2240/1632, wc m24 102-391, 102-392 initial issue status indicator raps 102-391 job actual parameter job execution argument error procedure switch power off then on. The problem continues. Y n return to service call procedures. Again, switch power off then on. 102-392 auditron inv...

  • Page 660

    09/03 2-627 dc 3535/2240/1632, wc m24 102-393, 102-394 status indicator raps initial issue 102-393 ep software failure procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-394 file access invalid file access pr...

  • Page 661

    09/03 2-628 dc 3535/2240/1632, wc m24 102-395, 102-396 initial issue status indicator raps 102-395 nvm nvm failure procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-396 ff ff error procedure switch power off...

  • Page 662

    09/03 2-629 dc 3535/2240/1632, wc m24 102-397, 102-398 status indicator raps initial issue 102-397 mgr mgr error. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. 102-398 delay release queue full delay release ...

  • Page 663

    09/03 2-630 dc 3535/2240/1632, wc m24 102-399 initial issue status indicator raps 102-399 internal internal error. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Perform re-installation of the software. If the problem continues, replace the control ...

  • Page 664

    09/03 2-631 dc 3535/2240/1632, wc m24 103-203, 103-204 status indicator raps initial issue 103-203 machine code failure product number failure (not initialized). Procedure caution during this procedure, do not make any prints or any copies until clear the fault. If the configu- ration sheet is enabl...

  • Page 665

    09/03 2-632 dc 3535/2240/1632, wc m24 103-207, 103-208 initial issue status indicator raps 103-207 all machine codes mismatch at least one of the three product codes are mismatched. Procedure caution during this procedure, do not make any prints or any copies until clear the fault. If the configu- r...

  • Page 666

    09/03 2-633 dc 3535/2240/1632, wc m24 103-320, 103-321 status indicator raps initial issue 103-320 rom failure a write error has occurred in the rom on the ess pwb. Procedure switch the power off then on. The fault is cleared. Y n replace the ess pwb ( pl 13.1 ). Return to service call procedures. 1...

  • Page 667

    09/03 2-634 dc 3535/2240/1632, wc m24 103-330, 103-331 initial issue status indicator raps 103-330 ess rom dimm #3 check failure an ess rom dimm #3 check failure was detected. Procedure switch the power off then on. The fault is cleared. Y n remove and replace the ess rom dimm #3. If the problem con...

  • Page 668

    09/03 2-635 dc 3535/2240/1632, wc m24 103-332, 103-333 status indicator raps initial issue 103-332 ess standard rom error an error was detected in the ess built-in standard rom. Procedure switch the power off then on. The fault is cleared. Y n remove and replace the ess built-in standard rom. If the...

  • Page 669

    09/03 2-636 dc 3535/2240/1632, wc m24 103-334, 103-335 initial issue status indicator raps 103-334 standard post script font rom error an error was detected in the standard built-in post script font rom. Procedure switch the power off then on. The fault is cleared. Y n replace the post script font r...

  • Page 670

    09/03 2-637 dc 3535/2240/1632, wc m24 103-336, 103-337 status indicator raps initial issue 103-336 ess ram dimm #3 w/r check failure a failure was detected during read/write check of the ess ram dimm #3. Procedure switch the power off then on. The fault is cleared. Y n remove and replace the ess ram...

  • Page 671

    09/03 2-638 dc 3535/2240/1632, wc m24 103-338, 103-339 initial issue status indicator raps 103-338 same post script font roms found the system detected that the same post script font rom was installed. Procedure switch the power off then on. The fault is cleared. Y n install the appropriate post scr...

  • Page 672

    09/03 2-639 dc 3535/2240/1632, wc m24 103-372, 103-701 status indicator raps initial issue 103-372 iot sc soft failure iot controller software failure was detected. Initial actions check fault history ( dc122 ) for faults (especially tray module faults) that occurred at the same time as this fault. ...

  • Page 673

    09/03 2-640 dc 3535/2240/1632, wc m24 103-702 initial issue status indicator raps 103-702 changed output bin: finisher to center the output tray was changed (finisher tray to center output tray). Procedure switch the power off then on. The problem continues. Y n return to service call procedures. Ag...

  • Page 674

    09/03 2-641 dc 3535/2240/1632, wc m24 116-200, 116-201 status indicator raps initial issue 116-200 main pwba ic an error was detected in the ic in the ess pwb. Initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem cont...

  • Page 675

    09/03 2-642 dc 3535/2240/1632, wc m24 116-206, 116-207 initial issue status indicator raps 116-206 timer a timer error was detected. Initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continues, reload system softwa...

  • Page 676

    09/03 2-643 dc 3535/2240/1632, wc m24 116-209, 116-310 status indicator raps initial issue 116-209 ess ps-1 rom check a failure was detected when the ess ps-1 rom was checked. Initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure pull out and inser...

  • Page 677

    09/03 2-644 dc 3535/2240/1632, wc m24 116-311, 116-314 initial issue status indicator raps 116-311 ess font rom dimm #3 check a failure was detected when the ess font rom dimm #3 was checked. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Pull out a...

  • Page 678

    09/03 2-645 dc 3535/2240/1632, wc m24 116-315, 116-316 status indicator raps initial issue 116-315 ess ram dimm #1 w/r check a failure was detected during w/r of the ess ram dimm #1. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Pull out and insert...

  • Page 679

    09/03 2-646 dc 3535/2240/1632, wc m24 116-317, 116-318 initial issue status indicator raps 116-317 standard rom dimm check an error was detected when the standard rom dimm was checked. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Pull out and inse...

  • Page 680

    09/03 2-647 dc 3535/2240/1632, wc m24 116-319, 116-320 status indicator raps initial issue 116-319 serial there is no serial board at the serial board initialization failure. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Reinstall the serial board....

  • Page 681

    09/03 2-648 dc 3535/2240/1632, wc m24 116-321, 116-323 initial issue status indicator raps 116-321 system software due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem persists, continue with the proc...

  • Page 682

    09/03 2-649 dc 3535/2240/1632, wc m24 116-324, 116-325 status indicator raps initial issue 116-324 exception error cpu exceptional error. Initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continues, reload system s...

  • Page 683

    09/03 2-650 dc 3535/2240/1632, wc m24 116-326, 116-327 initial issue status indicator raps 116-326 ess rom dimm #1 flash a failure was detected in the ess rom dimm #1 flash. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Pull out and insert the ess ...

  • Page 684

    09/03 2-651 dc 3535/2240/1632, wc m24 116-328, 116-329 status indicator raps initial issue 116-328 l2 cache a l2 cache failure was detected. Initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continues, reload syste...

  • Page 685

    09/03 2-652 dc 3535/2240/1632, wc m24 116-330, 116-332 initial issue status indicator raps 116-330 hdd file system the system detected that the an error has occurred or the hdd was not formatted during hdd check at power on. Procedure switch power off then on. The problem continues. Y n return to se...

  • Page 686

    09/03 2-653 dc 3535/2240/1632, wc m24 116-333, 116-335 status indicator raps initial issue 116-333 localtalk software due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem persists, continue with the p...

  • Page 687

    09/03 2-654 dc 3535/2240/1632, wc m24 116-336, 116-337 initial issue status indicator raps 116-336 redirector hd hd failure to be detected by redirector procedure switch power off then on. The problem continues. Y n return to service call procedures. Set up the hdd ( adj 9.8 ). If the problem contin...

  • Page 688

    09/03 2-655 dc 3535/2240/1632, wc m24 116-340, 116-341 status indicator raps initial issue 116-340 short of memory when the system detected that the memory was insufficient. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Add memory pull out postscri...

  • Page 689

    09/03 2-656 dc 3535/2240/1632, wc m24 116-342, 116-344 initial issue status indicator raps 116-342 jt monitor fatal errors to be detected by the jt monitor initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continue...

  • Page 690

    09/03 2-657 dc 3535/2240/1632, wc m24 116-345, 116-346 status indicator raps initial issue 116-345 token ring board token ring control ic access error procedure switch power off then on. The problem continues. Y n return to service call procedures. Go to the 116-900 rap. 116-346 formatter fatal erro...

  • Page 691

    09/03 2-658 dc 3535/2240/1632, wc m24 116-348, 116-349 initial issue status indicator raps 116-348 redirector fatal errors detected by redirector initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continues, reload ...

  • Page 692

    09/03 2-659 dc 3535/2240/1632, wc m24 116-350, 116-351 status indicator raps initial issue 116-350 appletalk software overall fatal errors of the appletalk due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the...

  • Page 693

    09/03 2-660 dc 3535/2240/1632, wc m24 116-352, 116-353 initial issue status indicator raps 116-352 netware software fatal error related to the netware due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the prob...

  • Page 694

    09/03 2-661 dc 3535/2240/1632, wc m24 116-355, 116-356 status indicator raps initial issue 116-355 snmp agent software fatal error related to the snmp agent due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If th...

  • Page 695

    09/03 2-662 dc 3535/2240/1632, wc m24 116-357, 116-358 initial issue status indicator raps 116-357 ps software ps fatal system error due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem persists, cont...

  • Page 696

    09/03 2-663 dc 3535/2240/1632, wc m24 116-359, 116-360 status indicator raps initial issue 116-359 plw software fatal error in plw due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem persists, contin...

  • Page 697

    09/03 2-664 dc 3535/2240/1632, wc m24 116-361, 116-365 initial issue status indicator raps 116-361 spool fatal hd fatal error of the spl hd the spool cont detected an error at hdd access. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Run the hdd di...

  • Page 698

    09/03 2-665 dc 3535/2240/1632, wc m24 116-366, 116-367 status indicator raps initial issue 116-366 report generator software an operation failure of the report generator. Due to an error during the software processing, the subsequent processes cannot be performed. Initial actions switch power off th...

  • Page 699

    09/03 2-666 dc 3535/2240/1632, wc m24 116-368, 116-370 initial issue status indicator raps 116-368 dump print fatal error of dump print. Due to an error during the software processing, the subsequent pro- cesses cannot be performed. Initial actions switch power off then on. If the problem persists, ...

  • Page 700

    09/03 2-667 dc 3535/2240/1632, wc m24 116-372, 116-373 status indicator raps initial issue 116-372 p-formatter fatal error of p-formatter. Due to an error during the software processing, the subsequent pro- cesses cannot be performed. Initial actions switch power off then on. If the problem persists...

  • Page 701

    09/03 2-668 dc 3535/2240/1632, wc m24 116-374, 116-375 initial issue status indicator raps 116-374 auto switch fatal error of auto sw. Due to an error during the software processing, the subsequent pro- cesses cannot be performed. Initial actions switch power off then on. If the problem persists, co...

  • Page 702

    09/03 2-669 dc 3535/2240/1632, wc m24 116-376, 116-377 status indicator raps initial issue 116-376 port 9100 software [port 9100 software fail initial actions switch power off then on. If the problem persists, continue with the procedure. Procedure perform gp 3 . If the problem continues, reload sys...

  • Page 703

    09/03 2-670 dc 3535/2240/1632, wc m24 116-378, 116-379 initial issue status indicator raps 116-378 mcr software fatal error of mcr (mail contents requester) procedure switch power off then on. The problem continues. Y n return to service call procedures. Again, switch power off then on. 116-379 mcc ...

  • Page 704

    09/03 2-671 dc 3535/2240/1632, wc m24 116-380, 116-381 status indicator raps initial issue 116-380 mf ui cont software fatal error of mf ui cont due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem pe...

  • Page 705

    09/03 2-672 dc 3535/2240/1632, wc m24 116-382, 116-388 initial issue status indicator raps 116-382 panel application layer command error on ui controller - mf ui panel: command error at the application level a necessary parameter was not sent from the panel, an length error was detected in a variabl...

  • Page 706

    09/03 2-673 dc 3535/2240/1632, wc m24 116-389, 116-390 status indicator raps initial issue 116-389 no add-on ram the necessary expansion ram was not installed. Though the system has the configuration requiring the installation of the expansion ram (with the hd), it detected that the expansion ram wa...

  • Page 707

    09/03 2-674 dc 3535/2240/1632, wc m24 116-395, 116-396 initial issue status indicator raps 116-395 usb software fatal error related to usb. Due to an error during the software processing, the subsequent pro- cesses cannot be performed. Initial actions switch power off then on. If the problem persist...

  • Page 708

    09/03 2-675 dc 3535/2240/1632, wc m24 116-398, 116-399 status indicator raps initial issue 116-398 ipp software fatal error related to ipp due to an error during the software processing, the subsequent processes cannot be per- formed. Initial actions switch power off then on. If the problem persists...

  • Page 709

    09/03 2-676 dc 3535/2240/1632, wc m24 116-701, 116-702 initial issue status indicator raps 116-701 execute forced separation of two sides due to insufficient memory, 2-sided print is impossible. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Expand ...

  • Page 710

    09/03 2-677 dc 3535/2240/1632, wc m24 116-703, 116-710 status indicator raps initial issue 116-703 ps interpret error an error has occurred in language analysis procedure switch power off then on. The problem continues. Y n return to service call procedures. Correct the job data. 116-710 hp-gl spool...

  • Page 711

    09/03 2-678 dc 3535/2240/1632, wc m24 116-711, 116-712 initial issue status indicator raps 116-711 plw form synthesis error synthesis is impossible because the size/orientation of the plw form's drawing is different from that of the paper. Procedure switch power off then on. The problem continues. Y...

  • Page 712

    09/03 2-679 dc 3535/2240/1632, wc m24 116-714, 116-715 status indicator raps initial issue 116-714 a hp-gl command error was detected [hp-gl/2 command error procedure switch power off then on. The problem continues. Y n return to service call procedures. Correct or remove the data in the print data ...

  • Page 713

    09/03 2-680 dc 3535/2240/1632, wc m24 116-718, 116-737 initial issue status indicator raps 116-718 plw form synthesis error the specified form is not registered. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Use a registered form, or register a nec...

  • Page 714

    09/03 2-681 dc 3535/2240/1632, wc m24 116-738, 116-739 status indicator raps initial issue 116-738 form synthesis error synthesis is impossible because the size/orientation of the form's drawing is different from that of the paper. Procedure switch power off then on. The problem continues. Y n retur...

  • Page 715

    09/03 2-682 dc 3535/2240/1632, wc m24 116-740, 116-741 initial issue status indicator raps 116-740 value calculation error the number calculated in the interpreter exceeded the limit value. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Remove the d...

  • Page 716

    09/03 2-683 dc 3535/2240/1632, wc m24 116-742, 116-743 status indicator raps initial issue 116-742 logo registry error the logo data cannot be registered because of the restriction of the number of logos. Procedure switch power off then on. The problem continues. Y n return to service call procedure...

  • Page 717

    09/03 2-684 dc 3535/2240/1632, wc m24 116-745, 116-746 initial issue status indicator raps 116-745 art command error the decomposer checks the syntax error and excess of each limit value at decomposing. Procedure switch power off then on. The problem continues. Y n return to service call procedures....

  • Page 718

    09/03 2-685 dc 3535/2240/1632, wc m24 116-747, 116-748 status indicator raps initial issue 116-747 white page detected after subtracting the paper margin from the valid coordinate area, the result of the calculation will be negative. Procedure switch power off then on. The problem continues. Y n ret...

  • Page 719

    09/03 2-686 dc 3535/2240/1632, wc m24 116-780, 116-790 initial issue status indicator raps 116-780 attached document failure of e-mail to xxx attached document e-mail failure. Procedure switch power off then on. The problem continues. Y n return to service call procedures. Attached document failure ...

  • Page 720

    09/03 2-687 dc 3535/2240/1632, wc m24 116-900 status indicator raps initial issue 116-900 token ring rap initial actions • ensure that the token ring pwba is connected to a good wall drop using a good network cable. • print a system settings list. With the assistance of the systems administrator ver...

  • Page 721

    09/03 2-688 dc 3535/2240/1632, wc m24 116-900 initial issue status indicator raps.

  • Page 722

    09/03 2-689 dc 3535/2240/1632, wc m24 121-310, 121-333 status indicator raps initial issue 121-310 foreign interface/foreign device communication fail communication cannot be established between the foreign interface and the foreign device (3rd-party device such as vend station or mechanical auditro...

  • Page 723

    09/03 2-690 dc 3535/2240/1632, wc m24 121-333, 121-334 initial issue status indicator raps figure 1 121-333 rap circuit diagram 121-334 foreign interface login fail the enquiry result of the login information was an error at wake up answer. Procedure caution do not attempt to troubleshoot this circu...

  • Page 724

    09/03 2-691 dc 3535/2240/1632, wc m24 121-335, 121-336 status indicator raps initial issue 121-335 foreign interface wake up answer fail the wake up answer cannot be received. Procedure caution do not attempt to troubleshoot this circuit by jumpering the transmit data or receive data lines (p343 pin...

  • Page 725

    09/03 2-692 dc 3535/2240/1632, wc m24 121-337, 121-338 initial issue status indicator raps 121-337 foreign device self diag fail the self diagnostics result of the connected foreign device was an error at wake up answer. Procedure switch the power off, then on. The problem continues. Y n check for l...

  • Page 726

    09/03 2-693 dc 3535/2240/1632, wc m24 121-350 status indicator raps initial issue 121-350 foreign interface logic fail due to an error during the software processing, the subsequent processes cannot be per- formed. Procedure caution do not attempt to troubleshoot this circuit by jumpering the transm...

  • Page 727

    09/03 2-694 dc 3535/2240/1632, wc m24 121-350 initial issue status indicator raps.

  • Page 728

    09/03 2-695 dc 3535/2240/1632, wc m24 202-399 status indicator raps initial issue 202-399 internal timer procedure switch the power off then on. The fault is cleared. Y n reload system software. Return to service call procedures..

  • Page 729

    09/03 2-696 dc 3535/2240/1632, wc m24 202-399 initial issue status indicator raps.

  • Page 730

    09/03 2-697 dc 3535/2240/1632, wc m24 of 1-1, of 1-2 status indicator raps initial issue of 1-1 +3.3 vdc use this rap to troubleshoot a failure with the +3.3 vdc. Procedure perform the following: • remove the rear cover ( rep 14.2 ). • tilt out the hvps chassis ( rep 1.6 ). Check that power is switc...

  • Page 731

    09/03 2-698 dc 3535/2240/1632, wc m24 of 1-3 initial issue status indicator raps of 1-3 +24 vdc enable use this rap to determine why the +24v lvps is not enabled. Procedure the machine is a dc 3535. Y n refer to figure 1 . +3.3 vdc is measured between p/j505 -3 (+) on the 24v lvps and gnd (-). Y n +...

  • Page 732

    09/03 2-699 dc 3535/2240/1632, wc m24 of 1-4 status indicator raps initial issue of 1-4 ac power ac power failure initial actions check circuit breaker. Procedure refer to figure 1 . Ac line voltage is measured between the noise filter pwb fs75 and fs74 ( pl 9.2 ). Y n ac line voltage is measured be...

  • Page 733

    09/03 2-700 dc 3535/2240/1632, wc m24 of 1-5 initial issue status indicator raps of 1-5 ac power off rap note: normal operation for the printer when the power is switched off is for ac power to remain applied to all power supplies for approximately 6 seconds for dc 2240/1632 and 25 seconds for the d...

  • Page 734

    09/03 2-701 dc 3535/2240/1632, wc m24 of 2-1 status indicator raps initial issue of 2-1 dark / blank display ui display is dark with minimal legibility, or no text or graphics are visible. Initial actions ensure all external cables and power cords are connected. Procedure note: if a status code is d...

  • Page 735

    09/03 2-702 dc 3535/2240/1632, wc m24 of 2-1 initial issue status indicator raps figure 1 of 2-1 rap circuit diagram.

  • Page 736

    09/03 2-703 dc 3535/2240/1632, wc m24 of 17-1 status indicator raps initial issue of 17-1 fax module checkout rap use this rap to troubleshoot failures on the fax module. Initial actions • ensure that all cables are properly connected. • check cables for wear or damage. • ensure that the machine is ...

  • Page 737

    09/03 2-704 dc 3535/2240/1632, wc m24 of 17-1 initial issue status indicator raps figure 1 fax module rap cd.

  • Page 738

    09/03 2-705 dc 3535/2240/1632, wc m24 of 99-1 status indicator raps initial issue of 99-1 reflective sensor rap sensors consist of a light-emitting diode and a photo transistor. When energized, the light from the led causes the photo transistor to conduct, drawing current through a pull-up resistor....

  • Page 739

    09/03 2-706 dc 3535/2240/1632, wc m24 of 99-2 initial issue status indicator raps of 99-2 transmissive sensor sensors consist of a light-emitting diode and a photo transistor. When energized, the light from the led causes the photo transistor to conduct, drawing current through a pull-up resistor. T...

  • Page 740

    09/03 2-707 dc 3535/2240/1632, wc m24 of 99-3 status indicator raps initial issue of 99-3 switch procedure enter dc330 [xxx-xxx]. Actuate the switch. The display changed. Y n refer to figure 1 . There is +3.5 / 5vdc measured between pin 2(+) of the switch and gnd(-). Y n check the wire between the s...

  • Page 741

    09/03 2-708 dc 3535/2240/1632, wc m24 of 99-4 initial issue status indicator raps of 99-4 generic solenoid/clutch rap solenoids and electric clutches are essentially electromagnets. Typically, a positive voltage is applied to one end of a coil, and a current driver is connected to the other end. Con...

  • Page 742

    09/03 2-709 dc 3535/2240/1632, wc m24 of 99-6, of 99-7 status indicator raps initial issue of 99-6 2 wire motor open procedure note: before performing this rap, ensure that the motor is free to rotate. Enter dc330 [xxx-xxx]. Refer to figure 1 . There is +24vdc measured between pin 3(+) of the pwb an...

  • Page 743

    09/03 2-710 dc 3535/2240/1632, wc m24 of 99-8 initial issue status indicator raps of 99-8 set gate solenoid open procedure refer to figure 1 . There is +24vdc measured between the nip/release solenoid pin 1 (+) and gnd (-). Y n there is +24vdc measured between the pwb pin 5 (+) and gnd(-). Y n check...

  • Page 744: 3 Image Quality

    09/03 3-1 dc 3535/2240/1632, wc m24 image quality initial issue 3 image quality image quality raps iq1 iot image quality entry rap .................................................................................. 3-3 iq2 iit image quality entry rap .....................................................

  • Page 745

    09/03 3-2 dc 3535/2240/1632, wc m24 initial issue image quality.

  • Page 746

    09/03 3-3 dc 3535/2240/1632, wc m24 iq1 image quality initial issue iq1 iot image quality entry rap the purpose of this rap is to serve as the entrance vehicle into the image quality raps sec- tion. All image quality raps must be accessed through this rap. The rap will have you evaluate the copies m...

  • Page 747

    09/03 3-4 dc 3535/2240/1632, wc m24 iq1 initial issue image quality high frequency bands repeating interval bands that are most noticeable in low density (20-30%) halftone areas of the copy. These bands run perpendicular to process direction. Go to the iq14 rap ibt cleaner streak multi-color streaks...

  • Page 748

    09/03 3-5 dc 3535/2240/1632, wc m24 iq2 image quality initial issue iq2 iit image quality entry rap this rap is for troubleshooting iit (scanner/adf) problems only. Before proceeding, verify that the defect is present in copy mode only. If the defect is present in print mode, go to the iq1 rap. Init...

  • Page 749

    09/03 3-6 dc 3535/2240/1632, wc m24 iq3, iq4 initial issue image quality iq3 low image density rap this rap troubleshoots the causes of output images showing image density lower than speci- fication. Initial actions • perform iq1 iot image quality entry rap first. • clean the ros windows. • replace ...

  • Page 750

    09/03 3-7 dc 3535/2240/1632, wc m24 iq5 image quality initial issue iq5 residual image (ghosting) rap initial actions • check the end-of-life counter for the drum cartridge. If the unit is at or near end-of-life, replace the drum cartridge (see machine consumables in section 6). Note: some ghosting ...

  • Page 751

    09/03 3-8 dc 3535/2240/1632, wc m24 iq5 initial issue image quality figure 1 iq5 rap circuit diagram.

  • Page 752

    09/03 3-9 dc 3535/2240/1632, wc m24 iq6 image quality initial issue iq6 iot background rap initial actions • perform iq1 iot image quality entry rap first. • perform max setup ( adj 9.1 ). If this does not resolve the problem, continue with this rap. Note: some background is unavoidable on certain m...

  • Page 753

    09/03 3-10 dc 3535/2240/1632, wc m24 iq7 initial issue image quality iq7 deletions rap initial actions reload with fresh, dry paper of the correct specifications. Paper contaminants (such as fibers or other particles) may cause spot deletions by interfering with the second transfer. If the prob- lem...

  • Page 754

    09/03 3-11 dc 3535/2240/1632, wc m24 iq7 image quality initial issue figure 1 iq7 rap circuit diagram.

  • Page 755

    09/03 3-12 dc 3535/2240/1632, wc m24 iq8 initial issue image quality iq8 color-to-color misregistration rap initial actions adjust the color registration ( adj 9.6 ). If the problem remains, continue with this procedure. Check the fault history for 4-640 , 4-641 , or 4-642 faults. Procedure the prob...

  • Page 756

    09/03 3-13 dc 3535/2240/1632, wc m24 iq9 image quality initial issue iq9 skew/misregistration rap this rap is used when skew, system registration, or magnification are out of specification. For color-to-color-misregistration, go to the iq8 rap. Initial actions load some new, dry 24 lb. 11x17/a3 xero...

  • Page 757

    09/03 3-14 dc 3535/2240/1632, wc m24 iq12 initial issue image quality iq12 process direction bands, streaks, and smears rap initial actions • clean the fuser. Check the metal stripper baffle in the fuser for contamination. • check the 2nd btr and the detack sawtooth for toner contamination. Procedur...

  • Page 758

    09/03 3-15 dc 3535/2240/1632, wc m24 iq13, iq14 image quality initial issue iq13 unfused copy/toner offset rap initial actions • replace the paper in use with fresh, dry paper of the correct specification. • check the post-fuser transport areas for dirt. • ensure that the media being used matches th...

  • Page 759

    09/03 3-16 dc 3535/2240/1632, wc m24 iq15 initial issue image quality iq15 mottle rap this rap troubleshoots the causes of output images showing image density that varies from inboard to outboard edges, or randomly throughout the print. Initial actions • replace the paper in use with fresh, dry pape...

  • Page 760

    09/03 3-17 dc 3535/2240/1632, wc m24 iq15 image quality initial issue note: performing the adjustments in the following table may not eliminate mottle completely, and/or may introduce other iq problems; the intent is to reach the best compromise. Table 1 heavyweight mottle options (dc 2240/1632 only...

  • Page 761

    09/03 3-18 dc 3535/2240/1632, wc m24 iq15 initial issue image quality table 2 2nd btr transfer remote locations - dc 2240/1632 default paper name user iq default nvm (side 1) nvm (side 2) plain paper a (bond) 1 746-059 746-076 plain paper b (plain) 2 746-060 746-076 plain paper c (recycled) 4 746-06...

  • Page 762

    09/03 3-19 dc 3535/2240/1632, wc m24 iq16, iq17 image quality initial issue iq16 spots rap initial actions ensure that the paper in use is fresh, dry, and within specification for weight and quality. Check print driver and copier control panel settings to ensure the media is being run in the proper ...

  • Page 763

    09/03 3-20 dc 3535/2240/1632, wc m24 iq20 initial issue image quality iq20 1st btr checkout rap procedure make a copy of the color test pattern. If the high density gradation patches (100%, 85%, and 70%) for one or more of c, y, m, or k appear to be light, perform the following: • refer to figure 1 ...

  • Page 764

    09/03 3-21 dc 3535/2240/1632, wc m24 iq20 image quality initial issue figure 1 iq20 rap circuit diagram.

  • Page 765

    09/03 3-22 dc 3535/2240/1632, wc m24 iq21 initial issue image quality iq21 developer bias rap procedure warning high voltage! Exercise caution when performing the voltage checks in this procedure. Enter dc140 [09-026]. Check the voltage at p/j580 for the affected color(s). There should be approximat...

  • Page 766

    09/03 3-23 dc 3535/2240/1632, wc m24 iq21 image quality initial issue figure 1 iq21 rap circuit diagram.

  • Page 767

    09/03 3-24 dc 3535/2240/1632, wc m24 iq22 initial issue image quality iq22 2nd btr checkout rap to isolate mechanical failure and out-of range voltages/current for the 2nd btr assembly. Caution high voltage! Exercise caution when performing the voltage checks in this procedure. Initial actions • per...

  • Page 768

    09/03 3-25 dc 3535/2240/1632, wc m24 iq22 image quality initial issue figure 1 iq22 rap circuit diagram.

  • Page 769

    09/03 3-26 dc 3535/2240/1632, wc m24 iq23 initial issue image quality iq23 bcr checkout rap use this procedure to troubleshoot edge-to-edge, very dense, single-color background procedure swap the drum cartridge that creates the high single-color background with any of the other drum cartridges and m...

  • Page 770

    09/03 3-27 dc 3535/2240/1632, wc m24 iq23 image quality initial issue figure 1 iq23 rap circuit diagram.

  • Page 771

    09/03 3-28 dc 3535/2240/1632, wc m24 initial issue image quality image quality specifications the following steps are used to set up the machine for the purpose of making test pattern cop- ies to judge output image color density, balance, and registration. 1. Set the following customer mode settings...

  • Page 772

    09/03 3-29 dc 3535/2240/1632, wc m24 image quality initial issue • original type - photo & text / halftone • lighter/darker - auto contrast • color saturation - normal • variable color balance - normal • sharpness - normal 2. Place test pattern 82e8220 on the platen and 24# xerox color xpressions 11...

  • Page 773

    09/03 3-30 dc 3535/2240/1632, wc m24 initial issue image quality figure 2 color and geometric test patterns.

  • Page 774

    09/03 3-31 dc 3535/2240/1632, wc m24 background image quality initial issue image defect samples the following figures contain examples of defects and their possible causes. • background • color misregistration • debris-centered deletions • deletions • high frequency bands • irregular process direct...

  • Page 775

    09/03 3-32 dc 3535/2240/1632, wc m24 color misregistration , debris-centered deletions initial issue image quality color misregistration figure 1 color misregistration defect sample cause failure of the ros or ibt “walking” from rear to front or front to rear. Mechanical problem in the ibt assembly....

  • Page 776

    09/03 3-33 dc 3535/2240/1632, wc m24 deletions, high frequency bands image quality initial issue deletions figure 1 deletions defect sample cause defective ibt belt, damp paper, uneven charge. Corrective action go to the iq7 rap. High frequency bands figure 1 high freq. Bands defect sample cause fau...

  • Page 777

    09/03 3-34 dc 3535/2240/1632, wc m24 irregular process direction streak , low image densi- initial issue image quality irregular process direction streak figure 1 streak defect sample cause clog in developer housing trim bar, malfunction of ibt cleaner assembly, contaminated ros window. Corrective a...

  • Page 778

    09/03 3-35 dc 3535/2240/1632, wc m24 moire, mottle image quality initial issue moire figure 1 moire defect sample cause the halftone screen used on the original interferes with the halftone screen used by the copier. Corrective action go to the iq2 rap. Mottle figure 1 mottle defect sample cause dam...

  • Page 779

    09/03 3-36 dc 3535/2240/1632, wc m24 newton rings, regular (repeating) bands, streaks, initial issue image quality newton rings figure 1 newton rings defect sample cause highly reflective surfaces on a glossy photograph. Corrective action perform the following: • clean the document glass • place a t...

  • Page 780

    09/03 3-37 dc 3535/2240/1632, wc m24 residual image, streak deletion in process direc- image quality initial issue residual image figure 1 residual image defect sample cause improper ibt cleaning and/or defective ibt belt. Corrective action go to the iq5 rap. Streak deletion in process direction fig...

  • Page 781

    09/03 3-38 dc 3535/2240/1632, wc m24 wrinkled image, cloud defect initial issue image quality wrinkled image figure 1 wrinkled image defect sample cause non-uniform paper buckle between ibt and fuser; fuser “tenting” of paper. Actual wrinkling of the paper itself can also occur. Corrective action go...

  • Page 782

    09/03 3-39 dc 3535/2240/1632, wc m24 ibt cleaner streak image quality initial issue ibt cleaner streak figure 1 ibt cleaner streak defect sample cause damage or wear to ibt cleaner assembly corrective action go to the iq12 rap. Inboard edge lead edge.

  • Page 783

    09/03 3-40 dc 3535/2240/1632, wc m24 ibt cleaner streak initial issue image quality.

  • Page 784: 4 Repairs &adjustments

    09/03 4-1 dc 3535/2240/1632, wc m24 repairs and adjustments initial issue 4 repairs &adjustments repairs electrical rep 1.1 lvps bracket ................................................................................................... 4-3 rep 1.2 mcu pwb ..............................................

  • Page 785

    09/03 4-2 dc 3535/2240/1632, wc m24 initial issue repairs and adjustments rep 9.7 toner dispenser ............................................................................................... 4-78 rep 9.8 plate assembly .................................................................................

  • Page 786

    09/03 4-3 dc 3535/2240/1632, wc m24 rep 1.1 repairs and adjustments initial issue rep 1.1 lvps bracket parts list on pl 9.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Caution p...

  • Page 787

    09/03 4-4 dc 3535/2240/1632, wc m24 rep 1.2 initial issue repairs and adjustments rep 1.2 mcu pwb parts list on pl 13.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Gather all...

  • Page 788

    09/03 4-5 dc 3535/2240/1632, wc m24 rep 1.4, rep 1.5 repairs and adjustments initial issue rep 1.4 3.3 v lvps or 5 v lvps parts list on pl 9.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the...

  • Page 789

    09/03 4-6 dc 3535/2240/1632, wc m24 rep 1.6, rep 1.7 initial issue repairs and adjustments rep 1.6 high voltage power supply chassis parts list on pl 9.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power app...

  • Page 790

    09/03 4-7 dc 3535/2240/1632, wc m24 rep 1.8 repairs and adjustments initial issue rep 1.8 i/f (interface) pwb parts list on pl 9.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1....

  • Page 791

    09/03 4-8 dc 3535/2240/1632, wc m24 rep 1.9, rep 1.10 initial issue repairs and adjustments rep 1.9 24 v lvps chassis parts list on pl 9.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mac...

  • Page 792

    09/03 4-9 dc 3535/2240/1632, wc m24 rep 1.11 repairs and adjustments initial issue rep 1.11 ac drive pwb parts list on pl 9.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remo...

  • Page 793

    09/03 4-10 dc 3535/2240/1632, wc m24 rep 1.12 initial issue repairs and adjustments rep 1.12 ess pwb parts list on pl 13.1 removal 1. Gather all available settings information. This includes the nvm log, the machine settings floppy, configuration report, etc. If possible save the current machine set...

  • Page 794

    09/03 4-11 dc 3535/2240/1632, wc m24 rep 1.12 repairs and adjustments initial issue figure 2 removing guide bracket and plate 8. Remove the chassis assembly riser ( figure 3 ). Figure 3 removing the chassis assembly riser caution pwbs can be damaged by electrostatic discharge. Observe all esd proced...

  • Page 795

    09/03 4-12 dc 3535/2240/1632, wc m24 rep 1.12 initial issue repairs and adjustments figure 4 removing ess pwb replacement 1. Reinstall the nvm pwb and the rom/ram/eproms that were removed from the original pwb. Discard the mac rom from the new ess pwb and install the mac rom removed from the old ess...

  • Page 796

    09/03 4-13 dc 3535/2240/1632, wc m24 rep 1.13 repairs and adjustments initial issue rep 1.13 ess nvm pwb parts list on pl 13.1 removal 1. Gather all available settings information. This includes the machine nvm log, the machine settings floppy disk, copies of the configuration report, etc. If possib...

  • Page 797

    09/03 4-14 dc 3535/2240/1632, wc m24 rep 1.14 initial issue repairs and adjustments rep 1.14 ps-1 rom, ps-2 rom parts list on pl 13.1 removal 1. Gather all available settings information. This includes the machine nvm log, the machine settings floppy disk, copies of the configuration report, etc. If...

  • Page 798

    09/03 4-15 dc 3535/2240/1632, wc m24 rep 1.15 repairs and adjustments initial issue rep 1.15 mcu nvm pwb parts list on pl 13.1 removal 1. Gather all available settings information. This includes the machine nvm log, the machine settings floppy disk, copies of the configuration report, etc. If possib...

  • Page 799

    09/03 4-16 dc 3535/2240/1632, wc m24 rep 1.17 initial issue repairs and adjustments rep 1.17 vsel pwb parts list on pl 13.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine caution pw...

  • Page 800

    09/03 4-17 dc 3535/2240/1632, wc m24 rep 1.17, rep 1.18 repairs and adjustments initial issue figure 4 removing the vsel pwb rep 1.18 fax module parts list on pl 9.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electric...

  • Page 801

    09/03 4-18 dc 3535/2240/1632, wc m24 rep 1.19 initial issue repairs and adjustments rep 1.19 one-touch panel parts list on pl 18.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1....

  • Page 802

    09/03 4-19 dc 3535/2240/1632, wc m24 rep 4.1 repairs and adjustments initial issue rep 4.1 main drive motor assembly parts list on pl 1.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mach...

  • Page 803

    09/03 4-20 dc 3535/2240/1632, wc m24 rep 4.2, rep 4.3 initial issue repairs and adjustments rep 4.2 ibt motor assembly parts list on pl 1.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ma...

  • Page 804

    09/03 4-21 dc 3535/2240/1632, wc m24 rep 4.4 repairs and adjustments initial issue rep 4.4 drum motor assembly parts list on pl 1.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. C...

  • Page 805

    09/03 4-22 dc 3535/2240/1632, wc m24 rep 4.4 initial issue repairs and adjustments.

  • Page 806

    09/03 4-23 dc 3535/2240/1632, wc m24 rep 5.1 repairs and adjustments initial issue rep 5.1 dadf parts list on pl 20.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Disconnect c...

  • Page 807

    09/03 4-24 dc 3535/2240/1632, wc m24 rep 5.2 initial issue repairs and adjustments rep 5.2 registration gate solenoid parts list on pl 20.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ma...

  • Page 808

    09/03 4-25 dc 3535/2240/1632, wc m24 rep 5.3 repairs and adjustments initial issue rep 5.3 left/right counterbalance parts list on pl 20.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mac...

  • Page 809

    09/03 4-26 dc 3535/2240/1632, wc m24 rep 5.4, rep 5.5 initial issue repairs and adjustments rep 5.4 dadf control pwb parts list on pl pl 20.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ...

  • Page 810

    09/03 4-27 dc 3535/2240/1632, wc m24 rep 5.6 repairs and adjustments initial issue rep 5.6 nudger roll parts list on pl 20.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remov...

  • Page 811

    09/03 4-28 dc 3535/2240/1632, wc m24 rep 5.7 initial issue repairs and adjustments rep 5.7 feed roll assembly parts list on pl 20.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1...

  • Page 812

    09/03 4-29 dc 3535/2240/1632, wc m24 rep 5.8, rep 5.9 repairs and adjustments initial issue rep 5.8 lower chute assembly parts list on pl 20.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the...

  • Page 813

    09/03 4-30 dc 3535/2240/1632, wc m24 rep 5.10 initial issue repairs and adjustments rep 5.10 set gate solenoid assembly parts list on pl 20.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ...

  • Page 814

    09/03 4-31 dc 3535/2240/1632, wc m24 rep 5.10 repairs and adjustments initial issue 2. Install set gate solenoid assembly ( figure 3 ). Figure 3 installing set gate solenoid assembly 1 position solenoid on screws 2 move solenoid as shown and tighten screws (2) 3 connect and secure harness in clip.

  • Page 815

    09/03 4-32 dc 3535/2240/1632, wc m24 rep 5.11 initial issue repairs and adjustments rep 5.11 registration sensor parts list on pl 20.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 816

    09/03 4-33 dc 3535/2240/1632, wc m24 rep 5.12, rep 5.13 repairs and adjustments initial issue rep 5.12 size sensors 1/2 (rear/front) parts list on pl 20.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power ap...

  • Page 817

    09/03 4-34 dc 3535/2240/1632, wc m24 rep 5.14 initial issue repairs and adjustments rep 5.14 duplex sensor parts list on pl 20.7 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. R...

  • Page 818

    09/03 4-35 dc 3535/2240/1632, wc m24 rep 5.15 repairs and adjustments initial issue rep 5.15 registration pinch roll parts list on pl 20.8 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mac...

  • Page 819

    09/03 4-36 dc 3535/2240/1632, wc m24 rep 5.15 initial issue repairs and adjustments 3. Remove gate ( figure 2 ). Figure 2 removing gate 4. Remove registration pinch roll ( figure 3 ). Figure 3 removing registration pinch roll 1 observe position of springs 2 remove screws (2) 3 remove gate while cont...

  • Page 820

    09/03 4-37 dc 3535/2240/1632, wc m24 rep 5.16, rep 5.17 repairs and adjustments initial issue rep 5.16 exit motor assembly parts list on pl 20.9 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to t...

  • Page 821

    09/03 4-38 dc 3535/2240/1632, wc m24 rep 5.18 initial issue repairs and adjustments rep 5.18 rear cover parts list on pl 20.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Caution...

  • Page 822

    09/03 4-39 dc 3535/2240/1632, wc m24 rep 5.19 repairs and adjustments initial issue rep 5.19 platen belt parts list on pl 20.10 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Re...

  • Page 823

    09/03 4-40 dc 3535/2240/1632, wc m24 rep 5.19 initial issue repairs and adjustments figure 3 install platen belt 3. Connect power cord and switch on power. 4. Enter dc330 [005-055]. Press start. Rotate platen belt for 15 seconds. Press stop. Check the belt position. If the belt moved to either side,...

  • Page 824

    09/03 4-41 dc 3535/2240/1632, wc m24 rep 6.1 repairs and adjustments initial issue rep 6.1 ros parts list on pl 3.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remove right c...

  • Page 825

    09/03 4-42 dc 3535/2240/1632, wc m24 rep 6.2 initial issue repairs and adjustments rep 6.2 platen glass parts list on pl 18.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Open...

  • Page 826

    09/03 4-43 dc 3535/2240/1632, wc m24 rep 6.3, rep 6.4 repairs and adjustments initial issue rep 6.3 iit top cover removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remove dadf ( re...

  • Page 827

    09/03 4-44 dc 3535/2240/1632, wc m24 rep 6.5 initial issue repairs and adjustments rep 6.5 iit/ips pwb parts list on pl 18.3 removal 1. Gather all available settings information. This includes the machine nvm log, the machine settings floppy disk, copies of the configuration report, etc. If possible...

  • Page 828

    09/03 4-45 dc 3535/2240/1632, wc m24 rep 6.6 repairs and adjustments initial issue rep 6.6 ui pwb parts list on pl 18.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Caution pwbs ...

  • Page 829

    09/03 4-46 dc 3535/2240/1632, wc m24 rep 6.11 initial issue repairs and adjustments rep 6.11 carriage cables parts list on pl 18.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. No...

  • Page 830

    09/03 4-47 dc 3535/2240/1632, wc m24 rep 6.11 repairs and adjustments initial issue 7. Remove the carriage cable ( figure 3 ). Figure 3 removing carriage cable replacement 1. Install the carriage cable. A. Orient the cable as shown and insert the middle carriage cable ball into the detente in the ca...

  • Page 831

    09/03 4-48 dc 3535/2240/1632, wc m24 rep 6.11 initial issue repairs and adjustments b. Prepare the spring/hook end for installation ( figure 5 ). Figure 5 preparing the spring/hook end c. Prepare the ball end for installation ( figure 6 ). Figure 6 preparing the ball end 1 hold the capstan ball in p...

  • Page 832

    09/03 4-49 dc 3535/2240/1632, wc m24 rep 6.11 repairs and adjustments initial issue d. Check orientation of the ends and number of carriage cable windings ( figure 7 ). Reconfigure as required. Figure 7 carriage cable orientation 2. Install carriage cable (ball end) ( figure 8 ). Figure 8 installing...

  • Page 833

    09/03 4-50 dc 3535/2240/1632, wc m24 rep 6.11 initial issue repairs and adjustments 3. Install carriage cable (spring/hook end) ( figure 9 ). Note: cable orientation for all pulleys used at the spring/hook end are fed across the pulleys from bottom-to-top. Figure 9 installing carriage cable (spring/...

  • Page 834

    09/03 4-51 dc 3535/2240/1632, wc m24 rep 6.12 repairs and adjustments initial issue rep 6.12 carriage motor parts list on pl 18.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. ...

  • Page 835

    09/03 4-52 dc 3535/2240/1632, wc m24 rep 6.13 initial issue repairs and adjustments rep 6.13 exposure lamp parts list on pl 18.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Caut...

  • Page 836

    09/03 4-53 dc 3535/2240/1632, wc m24 rep 6.14 repairs and adjustments initial issue rep 6.14 lamp wire harness parts list on pl 18.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. ...

  • Page 837

    09/03 4-54 dc 3535/2240/1632, wc m24 rep 6.14 initial issue repairs and adjustments 6. Remove lamp wire harness from full rate carriage ( figure 3 ). A. Turn the full rate carriage upside down. Figure 3 removing lamp wire harness replacement after reinstalling parts, adjust positions of full rate/ha...

  • Page 838

    09/03 4-55 dc 3535/2240/1632, wc m24 rep 7.1 repairs and adjustments initial issue rep 7.1 tray 5 parts list on pl 2.12 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remove the...

  • Page 839

    09/03 4-56 dc 3535/2240/1632, wc m24 rep 7.2 initial issue repairs and adjustments rep 7.2 tray 5 feed roll parts list on pl 2.14 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. ...

  • Page 840

    09/03 4-57 dc 3535/2240/1632, wc m24 rep 7.3, rep 7.4 repairs and adjustments initial issue rep 7.3 tray 1 feeder parts list on pl 2.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 841

    09/03 4-58 dc 3535/2240/1632, wc m24 rep 7.5, rep 7.6 initial issue repairs and adjustments rep 7.5 tray 1 paper size sensor parts list on pl 2.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to ...

  • Page 842

    09/03 4-59 dc 3535/2240/1632, wc m24 rep 7.7, rep 7.8 repairs and adjustments initial issue rep 7.7 tray 4 (ttm) parts list on pl 16.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 843

    09/03 4-60 dc 3535/2240/1632, wc m24 rep 7.9 initial issue repairs and adjustments rep 7.9 tray 2 (ttm) parts list on pl 16.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Pull...

  • Page 844

    09/03 4-61 dc 3535/2240/1632, wc m24 rep 7.10 repairs and adjustments initial issue rep 7.10 tray 2 feeder (ttm) parts list on pl 16.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 845

    09/03 4-62 dc 3535/2240/1632, wc m24 rep 7.11 initial issue repairs and adjustments rep 7.11 tray 3 feeder (ttm) parts list on pl 16.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 846

    09/03 4-63 dc 3535/2240/1632, wc m24 rep 7.12 repairs and adjustments initial issue rep 7.12 tray 4 feeder (ttm) parts list on pl 16.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 847

    09/03 4-64 dc 3535/2240/1632, wc m24 rep 7.12 initial issue repairs and adjustments 5. Remove the tray 4 feeder guides ( figure 3 ). Figure 3 removing the guides 6. Remove brackets from tray 4 feeder assembly ( figure 4 ). Figure 4 removing the brackets 1 remove screws (2) and upper guide 2 remove s...

  • Page 848

    09/03 4-65 dc 3535/2240/1632, wc m24 rep 7.13, rep 7.14 repairs and adjustments initial issue rep 7.13 tray 2 (3tm) parts list on pl 15.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mach...

  • Page 849

    09/03 4-66 dc 3535/2240/1632, wc m24 rep 7.15, rep 7.16 initial issue repairs and adjustments rep 7.15 tray 4 (3tm) parts list on pl 15.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mach...

  • Page 850

    09/03 4-67 dc 3535/2240/1632, wc m24 rep 7.17, rep 7.18 repairs and adjustments initial issue rep 7.17 tray 3 feeder (3tm) parts list on pl 15.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to t...

  • Page 851

    09/03 4-68 dc 3535/2240/1632, wc m24 rep 7.19 initial issue repairs and adjustments rep 7.19 tray module pwb parts list on pl 15.9 (3tm), pl 16.15 (ttm) removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power appl...

  • Page 852

    09/03 4-69 dc 3535/2240/1632, wc m24 rep 8.1 repairs and adjustments initial issue rep 8.1 left cover assembly parts list on pl 2.9 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1...

  • Page 853

    09/03 4-70 dc 3535/2240/1632, wc m24 rep 8.1 initial issue repairs and adjustments 8. Remove left cover assembly ( figure 2 ). Figure 2 removing left cover assembly replacement install left cover assembly on hinge pins, manually align marks on motion damper, then tip up transport to engage motion da...

  • Page 854

    09/03 4-71 dc 3535/2240/1632, wc m24 rep 8.2 repairs and adjustments initial issue rep 8.2 duplex chute parts list on pl 2.8 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remov...

  • Page 855

    09/03 4-72 dc 3535/2240/1632, wc m24 rep 8.3, rep 8.5 initial issue repairs and adjustments rep 8.3 duplex transport assembly parts list on pl 12.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied t...

  • Page 856

    09/03 4-73 dc 3535/2240/1632, wc m24 rep 8.6 repairs and adjustments initial issue rep 8.6 registration transport assembly parts list on pl 2.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to th...

  • Page 857

    09/03 4-74 dc 3535/2240/1632, wc m24 rep 8.7 initial issue repairs and adjustments rep 8.7 exit transport assembly parts list on pl 2.11 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 858

    09/03 4-75 dc 3535/2240/1632, wc m24 rep 9.1, rep 9.2 repairs and adjustments initial issue rep 9.1 drum cartridge parts list on pl 4.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machin...

  • Page 859

    09/03 4-76 dc 3535/2240/1632, wc m24 rep 9.3, rep 9.4 initial issue repairs and adjustments rep 9.3 waste toner cartridge cover parts list on pl 4.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied ...

  • Page 860

    09/03 4-77 dc 3535/2240/1632, wc m24 rep 9.5, rep 9.6 repairs and adjustments initial issue rep 9.5 full toner sensor parts list on pl 4.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mac...

  • Page 861

    09/03 4-78 dc 3535/2240/1632, wc m24 rep 9.7 initial issue repairs and adjustments rep 9.7 toner dispenser parts list on pl 6.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Op...

  • Page 862

    09/03 4-79 dc 3535/2240/1632, wc m24 rep 9.8 repairs and adjustments initial issue rep 9.8 plate assembly parts list on pl 4.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Rem...

  • Page 863

    09/03 4-80 dc 3535/2240/1632, wc m24 rep 9.8 initial issue repairs and adjustments 10. Disconnect developer housing harnesses ( figure 2 ). A. Open harness clip and remove harness from clip. B. Disconnect harness p/j’s (3). C. Remove screw from inner cover and remove cover. D. Remove developer housi...

  • Page 864

    09/03 4-81 dc 3535/2240/1632, wc m24 rep 9.9 repairs and adjustments initial issue rep 9.9 developer housing parts list on pl 6.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. ...

  • Page 865

    09/03 4-82 dc 3535/2240/1632, wc m24 rep 9.10 initial issue repairs and adjustments rep 9.10 developer parts list on pl 6.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Remove...

  • Page 866

    09/03 4-83 dc 3535/2240/1632, wc m24 rep 9.10, rep 9.11 repairs and adjustments initial issue figure 4 installing developer 2. Install developer housing. A. Ensure pin at rear of developer housing engages hole in rear frame of machine. B. Reassemble machine. C. Perform dc921 atc sensor setup ( adj 9...

  • Page 867

    09/03 4-84 dc 3535/2240/1632, wc m24 rep 9.12, rep 9.13 initial issue repairs and adjustments rep 9.12 ibt steering motor assembly parts list on pl 1.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power appli...

  • Page 868

    09/03 4-85 dc 3535/2240/1632, wc m24 rep 9.14, rep 9.15 repairs and adjustments initial issue rep 9.14 mob sensor assembly parts list on pl 1.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to th...

  • Page 869

    09/03 4-86 dc 3535/2240/1632, wc m24 rep 9.16, rep 9.17 initial issue repairs and adjustments rep 9.16 ibt cleaner assembly parts list on pl 5.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to t...

  • Page 870

    09/03 4-87 dc 3535/2240/1632, wc m24 rep 9.18 repairs and adjustments initial issue rep 9.18 lever assembly parts list on pl 5.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. O...

  • Page 871

    09/03 4-88 dc 3535/2240/1632, wc m24 rep 9.19, rep 9.20 initial issue repairs and adjustments rep 9.19 left hinge/right hinge parts list on pl 5.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to...

  • Page 872

    09/03 4-89 dc 3535/2240/1632, wc m24 rep 9.20, rep 9.21 repairs and adjustments initial issue 11. Remove right lift assembly ( figure 2 ). A. Remove auger mounting screws (2). B. Remove lift position screw. C. Remove secondary position screw. D. Remove lower screws (2). E. Remove right lift assembly...

  • Page 873

    09/03 4-90 dc 3535/2240/1632, wc m24 rep 9.21 initial issue repairs and adjustments figure 1 removing left lift assembly replacement 1. Install lift assembly. A. Position lift assembly in frame. B. Raise or lower xerographic frame as required and push in or pull out lift assembly actuator as require...

  • Page 874

    09/03 4-91 dc 3535/2240/1632, wc m24 rep 9.22 repairs and adjustments initial issue rep 9.22 transfer belt parts list on pl 5.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Cauti...

  • Page 875

    09/03 4-92 dc 3535/2240/1632, wc m24 rep 9.22 initial issue repairs and adjustments 6. Position support ( figure 4 ) figure 4 positioning latch 7. Install stand plate ( figure 5 ). Figure 5 installing stand plate 1 remove screw and support 2 install sup- port and screw.

  • Page 876

    09/03 4-93 dc 3535/2240/1632, wc m24 rep 9.22 repairs and adjustments initial issue 8. Place stand plate below and stand ibt belt assembly. 9. Relax tension of belt on both sides ( figure 6 ). Figure 6 relaxing belt tension 10. Remove brackets ( figure 7 ). Figure 7 removing bracket 1 forcefully pus...

  • Page 877

    09/03 4-94 dc 3535/2240/1632, wc m24 rep 9.22 initial issue repairs and adjustments 11. Pull out backup roll housing from hole below and rotate ( figure 8 ). Figure 8 pulling out backup roll housing 12. Remove transfer belt ( figure 9 ). Figure 9 removing transfer belt 1 lift backup roll hous- ing t...

  • Page 878

    09/03 4-95 dc 3535/2240/1632, wc m24 rep 9.22 repairs and adjustments initial issue replacement 1. Install transfer belt with reflector at rear ( figure 10 ). Figure 10 installing transfer belt 2. After installing transfer belt, move it to center of ibt frame so that exposed parts of ibt drive roll ...

  • Page 879

    09/03 4-96 dc 3535/2240/1632, wc m24 rep 9.22 initial issue repairs and adjustments 3. If transfer belt is skewed or wrinkled, perform following steps: ( figure 12 ). A. Relax tension of belt. B. Rotate gear in arrow direction and move transfer belt. Figure 12 re-positioning transfer belt 1 relax be...

  • Page 880

    09/03 4-97 dc 3535/2240/1632, wc m24 rep 9.23, rep 9.24 repairs and adjustments initial issue rep 9.23 1st btr roll parts list on pl 5.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 881

    09/03 4-98 dc 3535/2240/1632, wc m24 rep 9.25, rep 9.26 initial issue repairs and adjustments rep 9.25 erase lamp/rail (k,y,m,c) parts list on pl 4.2 replacement warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power app...

  • Page 882

    09/03 4-99 dc 3535/2240/1632, wc m24 rep 9.26 repairs and adjustments initial issue 12. Remove atc sensor ( figure 2 ). Figure 2 removing atc sensor replacement 1. Remove atc sensor setup data tag from new sensor. On tag, highlight k, c, m, or y as required for color of developer housing. Raise xero...

  • Page 883

    09/03 4-100 dc 3535/2240/1632, wc m24 rep 9.27 initial issue repairs and adjustments rep 9.27 retract shaft parts list on pl 5.4 replacement align camand flag as shown (both on the same side) ( figure 1 ). Figure 1 cam and flag alignment correct alignment incorrect alignment.

  • Page 884

    09/03 4-101 dc 3535/2240/1632, wc m24 rep 10.1, rep 10.2 repairs and adjustments initial issue rep 10.1 fuser parts list on pl 7.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. Wa...

  • Page 885

    09/03 4-102 dc 3535/2240/1632, wc m24 rep 10.3 initial issue repairs and adjustments rep 10.3 main/sub heater rod parts list on pl 7.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 886

    09/03 4-103 dc 3535/2240/1632, wc m24 rep 12.1 repairs and adjustments initial issue rep 12.1 h transport assembly parts list on pl 17.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 887

    09/03 4-104 dc 3535/2240/1632, wc m24 rep 12.2 initial issue repairs and adjustments rep 12.2 h transport belt parts list on pl 17.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. ...

  • Page 888

    09/03 4-105 dc 3535/2240/1632, wc m24 rep 12.3 repairs and adjustments initial issue rep 12.3 entrance sensor and top tray full sensor parts list on pl 17.4 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power ...

  • Page 889

    09/03 4-106 dc 3535/2240/1632, wc m24 rep 12.4 initial issue repairs and adjustments rep 12.4 finisher parts list on pl 17.5 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Separ...

  • Page 890

    09/03 4-107 dc 3535/2240/1632, wc m24 rep 12.5 repairs and adjustments initial issue rep 12.5 stack height sensor assembly parts list on pl 17.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to t...

  • Page 891

    09/03 4-108 dc 3535/2240/1632, wc m24 rep 12.6 initial issue repairs and adjustments rep 12.6 eject roll assembly parts list on pl 17.6 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machin...

  • Page 892

    09/03 4-109 dc 3535/2240/1632, wc m24 rep 12.6 repairs and adjustments initial issue 4. Remove the thumbscrews (2) ( figure 3 ). Figure 3 removing thumbscrews 5. Remove the tray guide ( figure 4 ). Figure 4 removing tray guide 1 remove screws (4) 2 remove fastener and cable clamp 3 remove cable from...

  • Page 893

    09/03 4-110 dc 3535/2240/1632, wc m24 rep 12.6 initial issue repairs and adjustments 6. Remove the home sensor ( figure 5 ). Figure 5 remove home sensor 7. Remove eject roll ( figure 6 ). Figure 6 removing eject roll disconnect harness and remove home sensor 1 remove clip, actuator, and clutch 2 rem...

  • Page 894

    09/03 4-111 dc 3535/2240/1632, wc m24 rep 12.6 repairs and adjustments initial issue 8. Remove eject shaft ( figure 7 ). Figure 7 removing eject shaft replacement 1. When replacing feed roll or eject shaft, replace them simultaneously. 2. When installing the clutch, be sure to insert the pawl into c...

  • Page 895

    09/03 4-112 dc 3535/2240/1632, wc m24 rep 12.6 initial issue repairs and adjustments 3. Make sure when installing the plate, that the cable tie (strain relief) is inside the bracket and the cable is routed through the notch ( figure 9 ). Figure 9 routing the cable notch cable tie (strain relief) bra...

  • Page 896

    09/03 4-113 dc 3535/2240/1632, wc m24 rep 12.7 repairs and adjustments initial issue rep 12.7 decurler roll parts list on pl 17.7 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. ...

  • Page 897

    09/03 4-114 dc 3535/2240/1632, wc m24 rep 12.8 initial issue repairs and adjustments rep 12.8 finisher drive motor parts list on pl 17.7 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 898

    09/03 4-115 dc 3535/2240/1632, wc m24 rep 12.9, rep 12.10 repairs and adjustments initial issue rep 12.9 belt parts list on pl 17.7 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1...

  • Page 899

    09/03 4-116 dc 3535/2240/1632, wc m24 rep 12.10 initial issue repairs and adjustments 3. Remove stapler assembly ( figure 2 ). Figure 2 removing stapler assembly 4. Remove the pwb cover ( figure 3 ). Figure 3 removing the pwb cover remove screws (2), ground wire (1) and stapler remove screws (10) an...

  • Page 900

    09/03 4-117 dc 3535/2240/1632, wc m24 rep 12.10 repairs and adjustments initial issue 5. Move the pwb chassis down ( figure 4 ). Figure 4 moving pwb chassis down 6. Remove rear rail mounting screws (2) ( figure 5 ). Figure 5 removing rear rail mounting screws 1 disconnect p848 and remove from guide ...

  • Page 901

    09/03 4-118 dc 3535/2240/1632, wc m24 rep 12.10 initial issue repairs and adjustments 7. Remove front rail mounting screws (2) ( figure 6 ). Figure 6 removing front rail mounting screws 8. Remove the rail assembly ( figure 7 ). Figure 7 removing rail assembly 2 remove screws (2) 1 disconnect connect...

  • Page 902

    09/03 4-119 dc 3535/2240/1632, wc m24 rep 12.10 repairs and adjustments initial issue 9. Remove the carriage assembly ( figure 8 ). Figure 8 removing the carriage assembly 10. Remove screws (5) and remove rail ( figure 9 ). Figure 9 removing rail screws (5).

  • Page 903

    09/03 4-120 dc 3535/2240/1632, wc m24 rep 12.11 initial issue repairs and adjustments rep 12.11 stapler assembly parts list on pl 17.9 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine...

  • Page 904

    09/03 4-121 dc 3535/2240/1632, wc m24 rep 12.11 repairs and adjustments initial issue replacement insert stapler assembly tab into slot ( figure 3 ). Figure 3 inserting tab into slot tab slot.

  • Page 905

    09/03 4-122 dc 3535/2240/1632, wc m24 rep 12.12 initial issue repairs and adjustments rep 12.12 compiler tray assembly parts list on pl 17.10 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ...

  • Page 906

    09/03 4-123 dc 3535/2240/1632, wc m24 rep 12.12 repairs and adjustments initial issue 4. Remove thumbscrews (2) ( figure 3 ). Figure 3 removing thumbscrews (2) 5. Remove the tray guide ( figure 4 ). Figure 4 removing tray guide 1 remove screws (4) 2 remove fastener and cable clamp 3 remove cable fro...

  • Page 907

    09/03 4-124 dc 3535/2240/1632, wc m24 rep 12.12 initial issue repairs and adjustments 6. Release compiler tray harness ( figure 5 ). Figure 5 releasing compiler tray harness 7. Remove the screw on the inboard side ( figure 6 ). Figure 6 removing screw on inboard side 1 disconnect and remove from gui...

  • Page 908

    09/03 4-125 dc 3535/2240/1632, wc m24 rep 12.12 repairs and adjustments initial issue 8. Remove the compiler tray assembly ( figure 7 ). Figure 7 removing compiler tray assembly replacement 1. Make sure when installing the plate, that the cable tie (strain relief) is inside the bracket and the cable...

  • Page 909

    09/03 4-126 dc 3535/2240/1632, wc m24 rep 12.13 initial issue repairs and adjustments rep 12.13 stacker motor assembly parts list on pl 17.11 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ...

  • Page 910

    09/03 4-127 dc 3535/2240/1632, wc m24 rep 12.14 repairs and adjustments initial issue rep 12.14 front elevator bracket parts list on pl 17.11 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ...

  • Page 911

    09/03 4-128 dc 3535/2240/1632, wc m24 rep 12.14 initial issue repairs and adjustments 4. Remove the thumbscrews (2) ( figure 3 ). Figure 3 removing thumbscrews 5. Remove the tray guide ( figure 4 ). Figure 4 removing tray guide 1 remove screws (4) 2 remove fastener and cable clamp 3 remove cable fro...

  • Page 912

    09/03 4-129 dc 3535/2240/1632, wc m24 rep 12.14 repairs and adjustments initial issue 6. Move pwb chassis ( figure 5 ). Figure 5 moving pwb chassis 7. Remove front elevator bracket ( figure 6 ). Figure 6 removing elevator bracket assembly 1 release wires from clamp 2 loosen screw 2 remove screws (2)...

  • Page 913

    09/03 4-130 dc 3535/2240/1632, wc m24 rep 12.14 initial issue repairs and adjustments replacement 1. Make sure when installing the plate, that the cable tie (strain relief) is inside the bracket and the cable is routed through the notch ( figure 7 ). Figure 7 routing the cable notch cable tie (strai...

  • Page 914

    09/03 4-131 dc 3535/2240/1632, wc m24 rep 12.15 repairs and adjustments initial issue rep 12.15 paddle gear shaft parts list on pl 17.12 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 915

    09/03 4-132 dc 3535/2240/1632, wc m24 rep 12.15 initial issue repairs and adjustments 5. Remove the paddle gear shaft ( figure 3 ). Figure 3 removing paddle gear shaft.

  • Page 916

    09/03 4-133 dc 3535/2240/1632, wc m24 rep 12.16 repairs and adjustments initial issue rep 12.16 finisher pwb parts list on pl 17.13 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. C...

  • Page 917

    09/03 4-134 dc 3535/2240/1632, wc m24 rep 12.16 initial issue repairs and adjustments 5. Remove the finisher pwb ( figure 3 ). Figure 3 removing finisher pwb replacement install the retained rom removed in step 3 of the removal procedure on the new finisher pwb. Before attempting to install the pwb ...

  • Page 918

    09/03 4-135 dc 3535/2240/1632, wc m24 rep 12.17 repairs and adjustments initial issue rep 12.17 entrance upper cover parts list on pl 17.3 removal 1. Remove the h transport assembly ( rep 12.1 ). 2. Remove the following: a. H transport front cover ( pl 17.3 ) b. H transport rear cover ( pl 17.3 ) 3....

  • Page 919

    09/03 4-136 dc 3535/2240/1632, wc m24 rep 12.17 initial issue repairs and adjustments 5. Remove the entrance upper cover ( figure 3 ) figure 3 removing the entrance upper cover 1 remove screws (4) 2 remove entrance upper cover.

  • Page 920

    09/03 4-137 dc 3535/2240/1632, wc m24 rep 12.18 repairs and adjustments initial issue rep 12.18 cam bracket assembly parts list on pl 17.8 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mac...

  • Page 921

    09/03 4-138 dc 3535/2240/1632, wc m24 rep 12.18 initial issue repairs and adjustments 4. Remove the cam bracket assembly ( figure 3 ). Figure 3 removing the cam bracket assembly replacement 1. Reinstall the cam bracket assembly ( figure 4 ). Figure 4 inserting axle of cam bracket assembly into hole ...

  • Page 922

    09/03 4-139 dc 3535/2240/1632, wc m24 rep 12.18 repairs and adjustments initial issue 2. Engage the solenoid pawl ( figure 5 ). Figure 5 engaging pawl with slot rotate cam so pawl engages slot.

  • Page 923

    09/03 4-140 dc 3535/2240/1632, wc m24 rep 12.19 initial issue repairs and adjustments rep 12.19 finisher rack assembly parts list on pl 17.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the m...

  • Page 924

    09/03 4-141 dc 3535/2240/1632, wc m24 rep 12.19 repairs and adjustments initial issue 4. Remove rear rack ( figure 3 ). Figure 3 removing rear rack 5. Remove front rack ( figure 4 ). Figure 4 removing front rack 1 remove thumbscrew 2 lift to remove rack 1 remove thumbscrew 2 lift to remove rack.

  • Page 925

    09/03 4-142 dc 3535/2240/1632, wc m24 rep 12.20 initial issue repairs and adjustments rep 12.20 lowering stacker tray parts list on pl 17.11 removal if the need arises to lower the stacker tray quickly or without power applied perform following: warning to avoid personal injury or shock, do not perf...

  • Page 926

    09/03 4-143 dc 3535/2240/1632, wc m24 rep 14.1 repairs and adjustments initial issue rep 14.1 top cover parts list on pl 10.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. With...

  • Page 927

    09/03 4-144 dc 3535/2240/1632, wc m24 rep 14.2, rep 14.3 initial issue repairs and adjustments rep 14.2 rear cover (iot) parts list on pl 10.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the...

  • Page 928

    09/03 4-145 dc 3535/2240/1632, wc m24 rep 14.3, rep 14.4 repairs and adjustments initial issue figure 2 removing right cover rep 14.4 rear left middle cover parts list on pl 10.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch o...

  • Page 929

    09/03 4-146 dc 3535/2240/1632, wc m24 rep 14.5, rep 14.6 initial issue repairs and adjustments rep 14.5 rear left upper cover parts list on pl 10.3 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied t...

  • Page 930

    09/03 4-147 dc 3535/2240/1632, wc m24 rep 14.7 repairs and adjustments initial issue rep 14.7 front cover assembly parts list on pl 10.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machi...

  • Page 931

    09/03 4-148 dc 3535/2240/1632, wc m24 rep 14.8, rep 14.9 initial issue repairs and adjustments rep 14.8 fuser cover parts list on pl 10.2 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the mach...

  • Page 932

    09/03 4-149 dc 3535/2240/1632, wc m24 rep 14.10, rep 14.11 repairs and adjustments initial issue rep 14.10 inner cover parts list on pl 8.1 removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the ma...

  • Page 933

    09/03 4-150 dc 3535/2240/1632, wc m24 rep 14.12 initial issue repairs and adjustments rep 14.12 left lower cover parts list on pl 16.16 (ttm), pl 15.11 (3tm) removal warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power...

  • Page 934

    09/03 4-151 dc 3535/2240/1632, wc m24 adj 5.1 repairs and adjustments initial issue adj 5.1 dadf side registration purpose align image scanned from document with left side edge of paper. Check 1. Make two copies from the platen glass to be used as dadf originals. A. Register test chart 82e8220 on pl...

  • Page 935

    09/03 4-152 dc 3535/2240/1632, wc m24 adj 5.1 initial issue repairs and adjustments adjustment 1. Adjust side 1 dadf side registration. A. Enter nvm rear/write ( dc131 ) [715-015]. Note: increasing value moves side edge metrics se1 through se4 toward edge. B. If b is more than a, increase the nvm va...

  • Page 936

    09/03 4-153 dc 3535/2240/1632, wc m24 adj 5.2 repairs and adjustments initial issue adj 5.2 dadf counterbalance purpose correct dadf opening and closing action. Check 1. Check dadf opening and closing action. A. Raise dadf and check that it remains in fully raised position. B. Check that the dadf cl...

  • Page 937

    09/03 4-154 dc 3535/2240/1632, wc m24 adj 5.3 initial issue repairs and adjustments adj 5.3 dadf parallelism purpose enable parallel document placement and image scan. Check warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electric...

  • Page 938

    09/03 4-155 dc 3535/2240/1632, wc m24 adj 5.4 repairs and adjustments initial issue adj 5.4 document transport height purpose enable document feed at the correct speed and free of skew. Check warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power swi...

  • Page 939

    09/03 4-156 dc 3535/2240/1632, wc m24 adj 5.4 initial issue repairs and adjustments 3. Adjust document transport height ( figure 3 ). Figure 3 adjusting document transport height 4. Repeat check. Lower document transport frame raise docu- ment trans- port frame 2 adjust screw 1 lower dadf 3 raise da...

  • Page 940

    09/03 4-157 dc 3535/2240/1632, wc m24 adj 5.5 repairs and adjustments initial issue adj 5.5 dadf top registration purpose align image scanned from document with top edge of paper. Check 1. Make two dadf originals. A. Register test chart 82e8220 on platen with lead edge metrics le1 through le3 agains...

  • Page 941

    09/03 4-158 dc 3535/2240/1632, wc m24 adj 5.5 initial issue repairs and adjustments • 1 copy iii. Press the start button. C. Check that top edge metrics are same distance from edge of paper for both copies. If the difference is greater than 1 mm, go to step 2 of the adjustment. Otherwise dadf side r...

  • Page 942

    09/03 4-159 dc 3535/2240/1632, wc m24 adj 5.6 repairs and adjustments initial issue adj 5.6 dadf document calibration purpose this procedure calibrates the document size detection circuitry in the dadf. Perform this adjustment whenever any the following occur: • replacement of the dadf. • when an er...

  • Page 943

    09/03 4-160 dc 3535/2240/1632, wc m24 adj 5.7 initial issue repairs and adjustments adj 5.7 dadf non-standard document custom registration purpose preliminary-document sizes other than dadf detectable document size (non-standard size) are registered and transported as standard document size. Hence, ...

  • Page 944

    09/03 4-161 dc 3535/2240/1632, wc m24 adj 6.1 repairs and adjustments initial issue adj 6.1 full/half rate carriage purpose establish full rate and half rate carriage position. Check warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or...

  • Page 945

    09/03 4-162 dc 3535/2240/1632, wc m24 adj 6.1 initial issue repairs and adjustments 4. Install alignment tool in front end of half rate carriage ( figure 3 ). Figure 3 installing alignment tool in front end of half rate carriage 5. Check that tool will install in other end of carriage. If the tool i...

  • Page 946

    09/03 4-163 dc 3535/2240/1632, wc m24 adj 6.1 repairs and adjustments initial issue 6. Check that alignment tool can be installed through frame into alignment hole in full rate carriage ( figure 5 ). If alignment tool fits through frame hole into full rate carriage alignment hole, perform the same c...

  • Page 947

    09/03 4-164 dc 3535/2240/1632, wc m24 adj 6.1 initial issue repairs and adjustments.

  • Page 948

    09/03 4-165 dc 3535/2240/1632, wc m24 adj 9.1 repairs and adjustments initial issue adj 9.1 max setup purpose to conduct a check of the machine and set it up so that excellent copy quality can be consis- tently obtained by stabilizing the development potential and copy density. Adjustment max setup ...

  • Page 949

    09/03 4-166 dc 3535/2240/1632, wc m24 adj 9.2 initial issue repairs and adjustments adj 9.2 atc sensor setup (dc921) purpose caution this procedure should only be performed when the atc sensor or developer housing is being replaced, or when there is reason to believe that the calibration values in n...

  • Page 950

    09/03 4-167 dc 3535/2240/1632, wc m24 adj 9.3, adj 9.4 repairs and adjustments initial issue adj 9.3 trc control/toner density setup (dc922) purpose to check the output of atc sensor and to determine if tc control performed normally. Allows manual adjustment of tc if control is not functioning. Chec...

  • Page 951

    09/03 4-168 dc 3535/2240/1632, wc m24 adj 9.5 initial issue repairs and adjustments adj 9.5 trc adjust (dc924) purpose caution perform this adjustment only to correct a strong customer complaint. Altering the setpoints will affect both print and copy modes. Also, there is quite a bit of overlap amon...

  • Page 952

    09/03 4-169 dc 3535/2240/1632, wc m24 adj 9.6 repairs and adjustments initial issue adj 9.6 color registration (dc685) purpose to establish correct horizontal and vertical positioning of the four primary color images the procedure consists of the following steps, which must be performed in the liste...

  • Page 953

    09/03 4-170 dc 3535/2240/1632, wc m24 adj 9.6 initial issue repairs and adjustments 4. Select the center setup button. 5. Select start. Caution make sure not to hook the wiring harness when moving the mob sensor. 6. If center setup is ok, dc685 is complete. Use the cleaning tool to pull the mob sens...

  • Page 954

    09/03 4-171 dc 3535/2240/1632, wc m24 adj 9.7, adj 9.8 repairs and adjustments initial issue adj 9.7 iit calibration (dc945) purpose • to calculate and set up the white reference correction coefficient. • to correct the iit sensitivity dispersion (ccd calibration). • adjust the light axis correction...

  • Page 955

    09/03 4-172 dc 3535/2240/1632, wc m24 adj 9.9 initial issue repairs and adjustments adj 9.9 iot registration series (dc129) purpose the purpose is to adjust the position of the printed image on the page. This is done by chang- ing the value in the appropriate nvm location in dc129. This controls whe...

  • Page 956

    09/03 4-173 dc 3535/2240/1632, wc m24 adj 9.9 repairs and adjustments initial issue side edge registration for paper trays 1 - 5 purpose note: each paper tray has a separate setting for side edge registration. To correctly position the side edge of the image in relation to the outboard edge of the p...

  • Page 957

    09/03 4-174 dc 3535/2240/1632, wc m24 adj 9.9, adj 9.10 initial issue repairs and adjustments lead edge registration for tray 5 (msi) purpose to correctly set the lead edge of the image in relation to the edge of the paper. Check 1. Load tray 5 with 8.5x11”/a4 lef paper. Depending on ess software ve...

  • Page 958

    09/03 4-175 dc 3535/2240/1632, wc m24 adj 9.10, adj 9.11 repairs and adjustments initial issue adjustment 1. Enter dc131 [715-301]. 2. Change the value: • each bit represents 0.036 mm • increase the value to move the image toward the lead edge. • decrease the value to move the image away from the le...

  • Page 959

    09/03 4-176 dc 3535/2240/1632, wc m24 adj 9.11, adj 9.12 initial issue repairs and adjustments 4. If the value is not within the specified range, perform the adjustment: adjustment 1. Enter dc131 [715-014]. 2. Change the value: • each bit represents 0.036 mm • increase the value to move the image to...

  • Page 960

    09/03 4-177 dc 3535/2240/1632, wc m24 adj 9.12 repairs and adjustments initial issue figure 1 checking horizontal magnification lead edge 200mm +/-1mm.

  • Page 961

    09/03 4-178 dc 3535/2240/1632, wc m24 adj 9.12 initial issue repairs and adjustments 4. Check vertical magnification ( figure 2 ): measure the 300mm line running from near le1 to the trail edge of the 1.8lp ladder. If the dimension is not 300mm ± 1.5mm, perform the adjustment. Figure 2 checking vert...

  • Page 962

    09/03 4-179 dc 3535/2240/1632, wc m24 adj 9.13 repairs and adjustments initial issue adj 9.13 ui display calibration purpose adjust the display by making the buttons on the display correspond to the touch panel, so that users can correctly select the content indicated on the display. Perform this ad...

  • Page 963

    09/03 4-180 dc 3535/2240/1632, wc m24 adj 9.14 initial issue repairs and adjustments adj 9.14 inboard/outboard density purpose caution perform this adjustment only to correct a customer complaint. Altering settings to correct for a specific condition may have unintended effects in other situations. ...

  • Page 964

    09/03 4-181 dc 3535/2240/1632, wc m24 adj 9.14 repairs and adjustments initial issue figure 2 pattern #1 figure 3 pattern #2 figure 4 pattern #3 figure 5 pattern #4.

  • Page 965

    09/03 4-182 dc 3535/2240/1632, wc m24 adj 9.14 initial issue repairs and adjustments figure 6 pattern #5 figure 7 pattern #6 figure 8 pattern #7 figure 9 pattern #8.

  • Page 966

    09/03 4-183 dc 3535/2240/1632, wc m24 adj 9.14 repairs and adjustments initial issue figure 10 pattern #9 figure 11 pattern #10 figure 12 pattern #11 figure 13 pattern #12.

  • Page 967

    09/03 4-184 dc 3535/2240/1632, wc m24 adj 9.14 initial issue repairs and adjustments figure 14 pattern #13 figure 15 pattern #14 figure 16 pattern #15 figure 17 pattern #16.

  • Page 968

    09/03 4-185 dc 3535/2240/1632, wc m24 adj 9.14 repairs and adjustments initial issue figure 18 pattern #17 figure 19 pattern #18 figure 20 pattern #19.

  • Page 969

    09/03 4-186 dc 3535/2240/1632, wc m24 adj 9.15 initial issue repairs and adjustments adj 9.15 light image setup purpose caution perform this adjustment only to correct a customer complaint. Altering settings to correct for a specific condition may have unintended effects in other situations. Make as...

  • Page 970

    09/03 4-187 dc 3535/2240/1632, wc m24 adj 9.15 repairs and adjustments initial issue 7. Perform an auto gradation for copy-text, copy-photo, print-text and print-photo (for dc3535, copy text, copy-photo, print, network controller 1). Check for the following: • prints improved but copies did not - ad...

  • Page 971

    09/03 4-188 dc 3535/2240/1632, wc m24 adj 9.15 initial issue repairs and adjustments.

  • Page 972

    09/03 4-189 dc 3535/2240/1632, wc m24 adj 12.1 repairs and adjustments initial issue adj 12.1 finisher alignment purpose align iot copy output with entrance to finisher h transport. Adjustment warning to avoid personal injury or shock, do not perform repair or adjustment activities with the power sw...

  • Page 973

    09/03 4-190 dc 3535/2240/1632, wc m24 adj 12.1 initial issue repairs and adjustments.

  • Page 974: 5 Parts List

    09/03 5-1 dc 3535/2240/1632, wc m24 parts list initial issue 5 parts list overview introduction ..................................................................................................................... 5-3 subsystem information ...............................................................

  • Page 975

    09/03 5-2 dc 3535/2240/1632, wc m24 initial issue parts list pl 16.11 tray 4 feeder: 1 of 2 ....................................................................................... 5-71 pl 16.12 tray 4 feeder: 2 of 2 .......................................................................................

  • Page 976

    09/03 5-3 dc 3535/2240/1632, wc m24 introduction parts list initial issue introduction overview the parts list section identifies all part numbers and the corresponding location of all spared subsystem components. Organization parts lists each item number in the part number listing corresponds to an...

  • Page 977

    09/03 5-4 dc 3535/2240/1632, wc m24 subsystem information initial issue parts list subsystem information use of the term “assembly” the term “assembly” will be used for items in the part number listing that include other itemized parts in the part number listing. When the word “assembly” is found in...

  • Page 978

    09/03 5-5 dc 3535/2240/1632, wc m24 symbology parts list initial issue symbology a tag number within a circle pointing to an item number shows that the part has been changed by the tag number within the circle (figure 1). Information on the modification is in the change tag index. Figure 1 with tag ...

  • Page 979

    09/03 5-6 dc 3535/2240/1632, wc m24 symbology initial issue parts list a tag number within a circle with no apex shows that the entire drawing has been changed by the tag number within the circle (figure 3). Information on the modification is in the change tag index. Figure 3 entire drawing with tag...

  • Page 980

    09/03 5-7 dc 3535/2240/1632, wc m24 pl 1.1 parts list initial issue pl 1.1 drive unit item part description 1 007k87370 drum motor assembly (dc3535) (rep 4.4) – 007k85750 drum motor assembly (dc2240/1632/wc24) (rep 4.4) 2 – drum motor (p/o pl 1.1 item 1) 3 – gear bracket (p/o pl 1.1 item 1) 4 007k87...

  • Page 981

    09/03 5-8 dc 3535/2240/1632, wc m24 pl 1.2 initial issue parts list pl 1.2 main drive motor assembly item part description 1 – friction clutch (not spared) 2 – shaft (not spared) 3 – gear (32t) (not spared) 4 – gear (28t) (not spared) 5 – bearing (not spared) 6 – shaft (not spared) 7 – gear (20t) (n...

  • Page 982

    09/03 5-9 dc 3535/2240/1632, wc m24 pl 1.3 parts list initial issue pl 1.3 ibt steering motor and mob sensor item part description 1 007k85580 ibt steering drive assembly (rep 9.12) 2 – ibt steering motor (p/o pl 1.3 item 1) 3 – plate (p/o pl 1.3 item 1) 4 130k60865 mob sensor assembly (rep 9.14,adj...

  • Page 983

    09/03 5-10 dc 3535/2240/1632, wc m24 pl 2.1 initial issue parts list pl 2.1 tray 1: 1 of 2 item part description 1 003e23672 stop 2 014e42850 spacer 3 110k08541 tray 1 paper size sensor (rep 7.5) 4 050k48981 tray 1 (dc3535/wc24) (rep 7.8) – 050k48171 tray 1 (dc2240/1632) (rep 7.8) 5 – cover (not spa...

  • Page 984

    09/03 5-11 dc 3535/2240/1632, wc m24 pl 2.2 parts list initial issue pl 2.2 tray 1: 2 of 2 item part description 1 892e90351 instruction label (dc3535/wc24) – 892e13310 instruction label (dc2240/1632) 2 – pad (not spared) 3 – max label (not spared) 4 – tray (not spared) 5 – side guide (not spared) 6...

  • Page 985

    09/03 5-12 dc 3535/2240/1632, wc m24 pl 2.3 initial issue parts list pl 2.3 tray 1 feeder and left lower cover assembly item part description 1 059k15573 tray 1 feeder (rep 7.3) 2 802k13193 left lower cover assembly (rep 14.6) 3 – left lower cover (p/o pl 2.3 item 2) 4 029e31600 rivet 5 – bracket (p...

  • Page 986

    09/03 5-13 dc 3535/2240/1632, wc m24 pl 2.4 parts list initial issue pl 2.4 tray 1 feeder: 1 of 2 item part description 1 127k23230 tray 1 feed/lift motor (rep 7.4) 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 – s...

  • Page 987

    09/03 5-14 dc 3535/2240/1632, wc m24 pl 2.5 initial issue parts list pl 2.5 tray 1 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared) 8 ...

  • Page 988

    09/03 5-15 dc 3535/2240/1632, wc m24 pl 2.6 parts list initial issue pl 2.6 registration transport item part description 1 059k24661 registration transport assembly (rep 8.6) 2 – bearing (p/o pl 2.6 item 1) 3 – bearing (p/o pl 2.6 item 1) 4 – takeaway roll (p/o pl 2.6 item 1) 5 – gear (22t) (p/o pl ...

  • Page 989

    09/03 5-16 dc 3535/2240/1632, wc m24 pl 2.7 initial issue parts list pl 2.7 left cover unit item part description 1 007e64740 damper gear (11/23t) 2 – stud (not spared) 3 004e11831 damper (white) 4 – left upper cover (not spared) 5 802k45492 left cover assembly 6 – left cover (p/o pl 2.7 item 5) 7 –...

  • Page 990

    09/03 5-17 dc 3535/2240/1632, wc m24 pl 2.8 parts list initial issue pl 2.8 left cover assembly: 1 of 2 item part description 1 054k22410 registration chute 2 – holder (not spared) 3 604k07070 2nd btr (rep 9.24) 4 809e26070 spring 5 015k48381 support 6 – left cover (not spared) 7 007e62630 gear (22t...

  • Page 991

    09/03 5-18 dc 3535/2240/1632, wc m24 pl 2.9 initial issue parts list pl 2.9 left cover assembly: 2 of 2 item part description 1 – bearing (not spared) 2 007k87440 gear 3 127k29511 2nd btr retract motor 4 130e82190 2nd btr retract sensor 5 – bracket (not spared) 6 130e84300 pob sensor 7 – bracket (no...

  • Page 992

    09/03 5-19 dc 3535/2240/1632, wc m24 pl 2.11 parts list initial issue pl 2.11 exit transport assembly item part description 1 059k29560 exit transport assembly (rep 8.7) 2 – exit transport cover (part of item 1) 3 – bearing (part of item 1) 4 – pin (part of item 1) 5 – exit roll (part of item 1) 6 1...

  • Page 993

    09/03 5-20 dc 3535/2240/1632, wc m24 pl 2.12 initial issue parts list pl 2.12 tray 5: 1 of 2 item part description 1 059k24802 tray 5 (dc2240/1632) (rep 7.1) – 059k25581 tray 5 (dc3535) (rep 7.1).

  • Page 994

    09/03 5-21 dc 3535/2240/1632, wc m24 pl 2.13 parts list initial issue pl 2.13 tray 5: 2 of 2 item part description 1 – spring (not spared) 2 – bracket (not spared) 3 – gear (not spared) 4 – spring (not spared) 5 050k48182 tray 5 assembly (dc2240/1632) – 050k48861 tray 5 assembly (dc3535) 6 – upper f...

  • Page 995

    09/03 5-22 dc 3535/2240/1632, wc m24 pl 2.14 initial issue parts list pl 2.14 tray 5 feed assembly item part description 1 038e23560 paper guide 2 – takeaway roll (not spared) 3 – bearing (not spared) 4 – gear (not spared) 5 – pick-up gear (not spared) 6 – cam gear (not spared) 7 – stop lever (not s...

  • Page 996

    09/03 5-23 dc 3535/2240/1632, wc m24 pl 2.15 parts list initial issue pl 2.15 tray 5 assembly item part description 1 – lower tray (not spared) 2 – cover (not spared) 3 – paper size sensor (not spared) 4 – side guide (not spared) 5 – attention label (not spared) 6 – instruction label (not spared) 7 ...

  • Page 997

    09/03 5-24 dc 3535/2240/1632, wc m24 pl 3.1 initial issue parts list pl 3.1 ros assembly item part description 1 – bracket (not spared) 2 062k10881 ros (dc2240/1632/wc24) (rep 6.1,adj 9.6) – 062k11421 ros (dc3535) (rep 6.1,adj 9.6) 3 – seal glass (y) (not spared) 4 – seal glass (m) (not spared) 5 – ...

  • Page 998

    09/03 5-25 dc 3535/2240/1632, wc m24 pl 4.1 parts list initial issue pl 4.1 xerographic module: 1 of 2 item part description 1 802k47090 waste toner cartridge cover (rep 9.3) 2 – waste toner cartridge (not spared) (rep 9.4) 3 003k86122 sensor holder assembly 4 – lever (p/o pl 4.1 item 3) 5 – waste t...

  • Page 999

    09/03 5-26 dc 3535/2240/1632, wc m24 pl 4.2 initial issue parts list pl 4.2 xerographic module: 2 of 2 item part description 1 015k52320 plate assembly (rep 9.8) 2 – wire harness (p/o pl 4.2 item 1) 3 – xero plate (p/o pl 4.2 item 1) 4 – block (m, c, k) (p/o pl 4.2 item 1) 5 – block (y) (p/o pl 4.2 ...

  • Page 1000

    09/03 5-27 dc 3535/2240/1632, wc m24 pl 5.1 parts list initial issue pl 5.1 lift unit item part description 1 001k70542 left lift assembly (rep 9.21) 2 001k70551 right lift assembly (rep 9.20) 3 – bearing (not spared) 4 – washer (not spared) 5 – plate (not spared) 6 003k12881 latch assembly 7 003e52...

  • Page 1001

    09/03 5-28 dc 3535/2240/1632, wc m24 pl 5.2 initial issue parts list pl 5.2 ibt unit item part description 1 604k07052 ibt belt assembly (rep 9.15,adj 9.6) 2 003k12650 removal support 3 – bearing (not spared) 4 007e61910 gear (14t) 5 007e61890 gear (18t) 6 – shaft (not spared) 7 802k12950 auger asse...

  • Page 1002

    09/03 5-29 dc 3535/2240/1632, wc m24 pl 5.3 parts list initial issue pl 5.3 ibt belt assembly item part description 1 – ibt belt cleaner assembly (p/o pl 5.2 item 1) (rep 9.16) 2 – blade (p/o pl 5.3 item 1) 3 – seal (p/o pl 5.3 item 1) 4 – screw (p/o pl 5.3 item 1) 5 – spring (p/o pl 5.3 item 1) 6 –...

  • Page 1003

    09/03 5-30 dc 3535/2240/1632, wc m24 pl 5.4 initial issue parts list pl 5.4 ibt frame assembly: 1 of 2 item part description 1 – frame (not spared) 2 130e84270 ibt home sensor (adj 9.6) 3 – spring (not spared) 4 – clamp (not spared) 5 130k60830 ibt edge sensor (adj 9.6) 6 162k56020 connector (c, k) ...

  • Page 1004

    09/03 5-31 dc 3535/2240/1632, wc m24 pl 5.5 parts list initial issue pl 5.5 ibt frame assembly: 2 of 2 item part description 1 – handle (not spared) 2 – spring (not spared) 3 – gear (not spared) 4 – plate (not spared) 5 – gear (not spared) 6 – bracket (not spared) 7 – top roll (not spared) 8 – front...

  • Page 1005

    09/03 5-32 dc 3535/2240/1632, wc m24 pl 5.6 initial issue parts list pl 5.6 ibt elevator item part description 1 809e26330 spring 2 015k49480 rear plunger 3 015k49310 front plunger 4 – frame (not spared) 5 014e43150 spacer.

  • Page 1006

    09/03 5-33 dc 3535/2240/1632, wc m24 pl 6.1 parts list initial issue pl 6.1 developer unit: 1 of 2 item part description 1 802k28810 toner dispenser (wc24) (rep 9.7) – 802k45910 toner dispenser (y) (dc3535/2240/1632) (rep 9.7) 2 – toner cartridge (not spared) 3 802k28820 toner dispenser (wc24) (rep ...

  • Page 1007

    09/03 5-34 dc 3535/2240/1632, wc m24 pl 6.2 initial issue parts list pl 6.2 developer unit: 2 of 2 item part description 1 802k28891 developer housing (y, m, k, c) (rep 9.9,adj 9.1) 2 – developer housing (p/o pl 6.2 item 1) 3 130k63000 atc sensor (y, m, k, c) (rep 9.26,adj 9.1) 4 035e65010 seal 5 60...

  • Page 1008

    09/03 5-35 dc 3535/2240/1632, wc m24 pl 7.1 parts list initial issue pl 7.1 fuser assembly: 1 of 2 item part description 1 126k14893 fuser (220v) (dc2240/1632) (rep 10.1) – 126k13943 fuser (120v) (dc2240/1632) (rep 10.1) – 008r12904 fuser (110v) (dc3535/wc24) (rep 10.1) – 008r12905 fuser (220v) (dc3...

  • Page 1009

    09/03 5-36 dc 3535/2240/1632, wc m24 pl 7.2 initial issue parts list pl 7.2 fuser assembly: 2 of 2 item part description 1 – front cover (not spared) 2 – rear cover (not spared) 3 – front lamp bracket (not spared) 4 126k13950 main heater rod (110v) (rep 10.3) – 126k13980 main heater rod (220v) (rep ...

  • Page 1010

    09/03 5-37 dc 3535/2240/1632, wc m24 pl 8.1 parts list initial issue pl 8.1 air system item part description 1 127k32730 ros shutter motor (rep 9.2) 2 – link (not spared) 3 – spring (not spared) 4 – inner cover (not spared) (rep 14.10) 5 – duct (not spared) 6 127k29340 fuser fan (rep 10.2) 7 – duct ...

  • Page 1011

    09/03 5-38 dc 3535/2240/1632, wc m24 pl 9.1 initial issue parts list pl 9.1 electrical components: 1 of 3 item part description 1 105k18772 dev/btr2/dts hvps (dc2240/1632/wc24) (rep 1.6 rep 1.7) – 105k20061 dev/btr2/dts hvps (dc3535) (rep 1.6 rep 1.7) 2 105e09981 bcr hvps (dc2240/1632/ wc24) (rep 1....

  • Page 1012

    09/03 5-39 dc 3535/2240/1632, wc m24 pl 9.2 parts list initial issue pl 9.2 electrical components: 2 of 3 item part description 1 101k38982 ac power chassis assembly (220v) (dc2240/1632/wc24) – 101k38812 ac power chassis assembly (110v) (dc2240/1632/wc24) – 101k39401 ac power chassis assembly (220v)...

  • Page 1013

    09/03 5-40 dc 3535/2240/1632, wc m24 pl 9.3 initial issue parts list pl 9.3 electrical components: 3 of 3 item part description 1 014k81604 developer block 2 162k62110 wire harness 3 162k55941 wire harness (y, m) 4 162k55971 wire harness (c, k) 5 162k56000 2nd wire harness 6 113k82310 dts connector ...

  • Page 1014

    09/03 5-41 dc 3535/2240/1632, wc m24 pl 9.4 parts list initial issue pl 9.4 fax module item part description 1 962k03981 wire harness 2 117k34640 usb cable 3 – stopper (not spared) 4 – fax module cover (not spared) 5 962k03500 wire harness 6 962k03490 wire harness 7 130k62980 speaker 8 160k88150 fax...

  • Page 1015

    09/03 5-42 dc 3535/2240/1632, wc m24 pl 10.1 initial issue parts list pl 10.1 front cover item part description 1 891e75951 logo plate (dc2240/1632) – 892e89060 logo plate (dc3535/wc24) 2 892e78280 name plate (16/32) (dc1632) – 892e78290 name plate (22/40) (dc2240) 3 802k46050 front cover assembly (...

  • Page 1016

    09/03 5-43 dc 3535/2240/1632, wc m24 pl 10.2 parts list initial issue pl 10.2 top covers and inner covers item part description 1 802k29611 top cover assembly (dc2240/1632) (rep 14.1) – 802k49801 top cover assembly (dc3535) (rep 14.1) – 802k49800 top cover assembly (wc24) (rep 14.1) 2 – top cover (p...

  • Page 1017

    09/03 5-44 dc 3535/2240/1632, wc m24 pl 10.3 initial issue parts list pl 10.3 rear cover item part description 1 – data plate (not spared) 2 802e12480 blind cover (dc2240/1632/wc24) – 802e33910 blind cover (dc3535) 3 802k28110 rear cover assembly 4 – rear cover (p/o pl 10.3 item 3) (rep 14.2) 5 802e...

  • Page 1018

    09/03 5-45 dc 3535/2240/1632, wc m24 pl 11.1 parts list initial issue pl 11.1 inverter transport: 1 of 2 item part description 1 059k16742 inverter transport (rep 8.5).

  • Page 1019

    09/03 5-46 dc 3535/2240/1632, wc m24 pl 11.2 initial issue parts list pl 11.2 inverter transport: 2 of 2 item part description 1 – cover (not spared) 2 015k45802 clutch assembly 3 – wire harness (not spared) 4 121k22870 reverse clutch 5 011e10711 interlock actuator 6 – gear (23t) (p/o pl 11.2 item 2...

  • Page 1020

    09/03 5-47 dc 3535/2240/1632, wc m24 pl 12.1 parts list initial issue pl 12.1 duplex transport assembly: 1 of 2 item part description 1 – duplex transport upper cover (not spared) 2 059k18714 duplex transport assembly (rep 8.3) 3 – one-way pulley (p/o pl 12.1 item 2) 4 – bearing (p/o pl 12.1 item 2)...

  • Page 1021

    09/03 5-48 dc 3535/2240/1632, wc m24 pl 12.2 initial issue parts list pl 12.2 duplex transport assembly: 2 of 2 item part description 1 – spring (not spared) 2 059k23470 pinch roll 3 – cover (not spared) 4 160k66860 duplex transport pwb 5 – wire harness (not spared) 6 – bracket (not spared) 7 130k61...

  • Page 1022

    09/03 5-49 dc 3535/2240/1632, wc m24 pl 13.1 parts list initial issue pl 13.1 ess item part description 1 160k74231 ess pwb (dc2240/1632/wc24) (rep 1.12) – 160k90570 ess pwb (dc3535) (rep 1.12) 2 160k99070 mcu pwb (wc24) (rep 1.2) – – mcu pwb (p/o pl 13.1 item 35) (dc2240/1632) (rep 1.2) – 160k91963...

  • Page 1023

    09/03 5-50 dc 3535/2240/1632, wc m24 pl 15.1 initial issue parts list pl 15.1 tray 2/3/4 feeder item part description 1 050k48840 tray 2/3/4 (rep 7.13 rep 7.14 rep 7.15) – 050k48980 tray 2 (wc24) (rep 7.13 rep 7.14 rep 7.15) 2 892e89190 label (tray 2) – 892e89200 label (tray 3) – 892e89210 label (tr...

  • Page 1024

    09/03 5-51 dc 3535/2240/1632, wc m24 pl 15.2 parts list initial issue pl 15.2 tray assembly item part description 1 892e90351 instruction label (dc3535/wc24) – 892e13310 instruction label (dc2240/1632) 2 – pad (not spared) 3 – max label (not spared) 4 – tray (not spared) 5 – side guide (not spared) ...

  • Page 1025

    09/03 5-52 dc 3535/2240/1632, wc m24 pl 15.3 initial issue parts list pl 15.3 tray 2 feeder: 1 of 2 item part description 1 127k23230 tray 2 feed/lift motor (rep 7.4) 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 –...

  • Page 1026

    09/03 5-53 dc 3535/2240/1632, wc m24 pl 15.4 parts list initial issue pl 15.4 tray 2 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared) ...

  • Page 1027

    09/03 5-54 dc 3535/2240/1632, wc m24 pl 15.5 initial issue parts list pl 15.5 tray 3 feeder: 1 of 2 item part description 1 127k23230 tray 3 feed/lift motor (rep 7.4) 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 –...

  • Page 1028

    09/03 5-55 dc 3535/2240/1632, wc m24 pl 15.6 parts list initial issue pl 15.6 tray 3 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared) ...

  • Page 1029

    09/03 5-56 dc 3535/2240/1632, wc m24 pl 15.7 initial issue parts list pl 15.7 tray 4 feeder: 1 of 2 item part description 1 127k23230 tray 4 feed/lift motor (rep 7.4) 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 –...

  • Page 1030

    09/03 5-57 dc 3535/2240/1632, wc m24 pl 15.8 parts list initial issue pl 15.8 tray 4 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared) ...

  • Page 1031

    09/03 5-58 dc 3535/2240/1632, wc m24 pl 15.9 initial issue parts list pl 15.9 electrical components and casters item part description 1 – left connecting bracket (not spared) 2 – right connecting bracket (not spared) 3 017k92350 caster 4 017k92360 caster 5 – foot (not spared) 6 – bracket (not spared...

  • Page 1032

    09/03 5-59 dc 3535/2240/1632, wc m24 pl 15.10 parts list initial issue pl 15.10 left cover assembly item part description 1 802k25721 left cover assembly (rep 14.11) 2 003e53700 shaft 3 003e53710 hook 4 011e10800 handle 5 – left cover (p/o pl 15.10 item 1) 6 – support (p/o pl 15.10 item 1) 7 – cover...

  • Page 1033

    09/03 5-60 dc 3535/2240/1632, wc m24 pl 15.11 initial issue parts list pl 15.11 covers item part description 1 802e23950 front upper cover 2 802e23960 front lower cover 3 802e23941 right cover 4 802e23930 left lower cover (rep 14.12) 5 802k50490 rear cover (rep 14.9).

  • Page 1034

    09/03 5-61 dc 3535/2240/1632, wc m24 pl 16.1 parts list initial issue pl 16.1 tray 2/3/4 assembly item part description 1 891e49060 label (tray 2) (dc2240/1632) – 892e89190 label (tray 2) (dc3535/wc24) 2 050k48171 tray 2 (dc2240/1632) (rep 7.9) – 050k48981 tray 2 (dc3535/wc24) (rep 7.9) 3 003e23672 ...

  • Page 1035

    09/03 5-62 dc 3535/2240/1632, wc m24 pl 16.2 initial issue parts list pl 16.2 tray 2 item part description 1 892e74500 instruction label 2 – pad (not spared) 3 – max label (not spared) 4 – tray (not spared) 5 – side guide (not spared) 6 – end guide (not spared) 7 – link (not spared) 8 – stop (not sp...

  • Page 1036

    09/03 5-63 dc 3535/2240/1632, wc m24 pl 16.3 parts list initial issue pl 16.3 tray 3 item part description 1 802e23990 tray 3 cover 2 – pulley (not spared) 3 – lift shaft (not spared) 4 – bearing (not spared) 5 – pulley (not spared) 6 – pulley (not spared) 7 – cable guide (not spared) 8 020e93120 pu...

  • Page 1037

    09/03 5-64 dc 3535/2240/1632, wc m24 pl 16.4 initial issue parts list pl 16.4 tray 4 item part description 1 802e23980 tray 4 cover 2 – tray front frame (not spared) 3 – lift shaft (not spared) 4 – lift gear (not spared) 5 – bearing (not spared) 6 – brake (not spared) 7 – pulley (not spared) 8 – cab...

  • Page 1038

    09/03 5-65 dc 3535/2240/1632, wc m24 pl 16.5 parts list initial issue pl 16.5 paper feeder: 1 of 2 item part description 1 – spacer (not spared) 2 – guide (not spared) 3 – stop (not spared) 4 059k21790 tray 4 transport assembly 5 – upper chute (p/o pl 16.5 item 4) 6 – takeaway roll (p/o pl 16.5 item...

  • Page 1039

    09/03 5-66 dc 3535/2240/1632, wc m24 pl 16.6 initial issue parts list pl 16.6 paper feeder: 2 of 2 item part description 1 059k18900 takeaway roll 2 – bearing (not spared) 3 – chute (not spared) 4 – cover (not spared) 5 130k61510 takeaway sensor 6 162k62810 wire harness 7 059k15573 tray 2/tray 3 fee...

  • Page 1040

    09/03 5-67 dc 3535/2240/1632, wc m24 pl 16.7 parts list initial issue pl 16.7 tray 2 feeder: 1 of 2 item part description 1 127k23230 tray 2 feed/lift motor 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 – shaft (no...

  • Page 1041

    09/03 5-68 dc 3535/2240/1632, wc m24 pl 16.8 initial issue parts list pl 16.8 tray 2 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared) ...

  • Page 1042

    09/03 5-69 dc 3535/2240/1632, wc m24 pl 16.9 parts list initial issue pl 16.9 tray 3 feeder: 1 of 2 item part description 1 127k23230 tray 3 feed/lift motor 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 – shaft (no...

  • Page 1043

    09/03 5-70 dc 3535/2240/1632, wc m24 pl 16.10 initial issue parts list pl 16.10 tray 3 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared...

  • Page 1044

    09/03 5-71 dc 3535/2240/1632, wc m24 pl 16.11 parts list initial issue pl 16.11 tray 4 feeder: 1 of 2 item part description 1 127k23230 tray 4 feed/lift motor 2 – bracket (not spared) 3 005k83081 one-way clutch 4 007k85730 one-way gear 5 – gear (13t) (not spared) 6 – bearing (not spared) 7 – shaft (...

  • Page 1045

    09/03 5-72 dc 3535/2240/1632, wc m24 pl 16.12 initial issue parts list pl 16.12 tray 4 feeder: 2 of 2 item part description 1 – spring (not spared) 2 600k78460 roll kit (3 rolls/kit) 3 005k05890 one-way clutch 4 – gear (not spared) 5 – shaft (not spared) 6 – chute (not spared) 7 – spring (not spared...

  • Page 1046

    09/03 5-73 dc 3535/2240/1632, wc m24 pl 16.13 parts list initial issue pl 16.13 left cover assembly item part description 1 802k25731 left cover assembly (rep 14.11) 2 003e53700 shaft 3 003e53710 hook 4 011e10800 handle 5 – left cover (p/o pl 16.13 item 1) 6 – support (p/o pl 16.13 item 1) 7 – cover...

  • Page 1047

    09/03 5-74 dc 3535/2240/1632, wc m24 pl 16.14 initial issue parts list pl 16.14 tray 3/4 lift gear assembly item part description 1 – transport guide (not spared) 2 015k49460 gear assembly (tray 3) 3 015k49450 gear assembly (tray 4) 4 007e66080 lift gear 5 011k96790 coupling 6 – bearing (not spared).

  • Page 1048

    09/03 5-75 dc 3535/2240/1632, wc m24 pl 16.15 parts list initial issue pl 16.15 electrical components and casters item part description 1 007e66060 gear (23/46t) 2 007e66070 gear (46t) 3 007e66050 gear (33t) 4 127k31840 takeaway motor 2 5 127k36020 takeaway motor 1 6 – left coupling (not spared) 7 –...

  • Page 1049

    09/03 5-76 dc 3535/2240/1632, wc m24 pl 16.16 initial issue parts list pl 16.16 covers item part description 1 – right cover (not spared) 2 802e23950 front upper cover 3 802e23960 front lower cover 4 802k36580 rear cover (rep 14.9) 5 802e23930 left lower cover (rep 14.12).

  • Page 1050

    09/03 5-77 dc 3535/2240/1632, wc m24 pl 17.1 parts list initial issue pl 17.1 finisher item part description 1 802k49900 gate assembly 2 801k03600 h-transport assembly (rep 12.1) 3 – stapler finisher (not spared) 4 003k12090 thumbscrew 5 – rack assembly (not spared) (rep 12.19) 6 – right cover (not ...

  • Page 1051

    09/03 5-78 dc 3535/2240/1632, wc m24 pl 17.2 initial issue parts list pl 17.2 gate assembly item part description 1 – gate cover (not spared) 2 – bearing (not spared) 3 – chute (not spared) 4 – in gate (not spared) 5 – in gate lever (not spared) 6 – gate bracket (not spared) 7 – link assembly (not s...

  • Page 1052

    09/03 5-79 dc 3535/2240/1632, wc m24 pl 17.3 parts list initial issue pl 17.3 h-transport assembly: 1 of 2 item part description 1 802k28600 h-transport cover assembly 2 – h-transport cover (p/o pl 17.3 item 1) 3 – screw (p/o pl 17.3 item 1) 4 121e89780 magnet 5 – guide (p/o pl 17.3 item 1) 6 – roll...

  • Page 1053

    09/03 5-80 dc 3535/2240/1632, wc m24 pl 17.4 initial issue parts list pl 17.4 h-transport assembly: 2 of 2 item part description 1 – h-transport roll (in) (not spared) 2 – h-transport roll (out) (not spared) 3 023e20020 h-transport belt (rep 12.2) 4 – roll (not spared) 5 – support (not spared) 6 – b...

  • Page 1054

    09/03 5-81 dc 3535/2240/1632, wc m24 pl 17.5 parts list initial issue pl 17.5 covers item part description 1 802e28560 front cover 2 802e28520 rear cover 3 802e28530 top cover 4 802e50710 left cover 5 802e28550 front cover door 6 802e28570 left panel 7 – hinge (not spared) 8 121e88470 magnet.

  • Page 1055

    09/03 5-82 dc 3535/2240/1632, wc m24 pl 17.6 initial issue parts list pl 17.6 top cover and eject roll item part description 1 802k28571 top cover 2 – arm (not spared) 3 – bearing (not spared) 4 – bracket (not spared) 5 – spring (not spared) 6 830e81670 support 7 – bracket (not spared) 8 – shaft (no...

  • Page 1056

    09/03 5-83 dc 3535/2240/1632, wc m24 pl 17.7 parts list initial issue pl 17.7 paper transportation: 1 of 2 item part description 1 120e20690 actuator 2 121k24610 decurler cam clutch 3 008e94070 cam 4 – shaft (not spared) 5 – bearing (not spared) 6 031e94030 arm 7 059k20210 decurler roll (rep 12.7) 8...

  • Page 1057

    09/03 5-84 dc 3535/2240/1632, wc m24 pl 17.8 initial issue parts list pl 17.8 paper transportation: 2 of 2 item part description 1 604k11150 finisher dr repair kit 2 020e34970 pulley 3 007e67780 gear (15z) 4 423w28054 belt 5 007e67810 gear (30z) 6 – collar (p/o pl 17.8 item 1) 7 – gear pulley (p/o p...

  • Page 1058

    09/03 5-85 dc 3535/2240/1632, wc m24 pl 17.9 parts list initial issue pl 17.9 stapler unit item part description 1 041k94260 carriage assembly 2 – bracket (p/o pl 17.9 item 1) 3 127k32860 staple move motor 4 – gear (p/o pl 17.9 item 1) 5 130e82530 staple move sensor 6 – roll (p/o pl 17.9 item 1) 7 –...

  • Page 1059

    09/03 5-86 dc 3535/2240/1632, wc m24 pl 17.10 initial issue parts list pl 17.10 compiler tray assembly item part description 1 050k43880 compiler tray assembly (rep 12.12) 2 127k32850 front/rear tamper motor 3 – plate (p/o pl 17.10 item 1) 4 130e82530 front/rear tamper home sensor 5 – rack (p/o pl 1...

  • Page 1060

    09/03 5-87 dc 3535/2240/1632, wc m24 pl 17.11 parts list initial issue pl 17.11 elevator item part description 1 127k33420 stacker motor assembly (rep 12.13) 2 015k50680 front elevator bracket (rep 12.14) 3 019e50340 clamp 4 – bearing (not spared) 5 007e67830 rear gear 6 – actuator (not spared) 7 00...

  • Page 1061

    09/03 5-88 dc 3535/2240/1632, wc m24 pl 17.12 initial issue parts list pl 17.12 exit assembly item part description 1 007e72080 gear (48z) 2 – bearing (not spared) 3 006k21720 exit shaft 4 – collar (not spared) 5 007e72070 gear (32z/18t) 6 – bearing (not spared) 7 006k21970 paddle gear shaft (rep 12...

  • Page 1062

    09/03 5-89 dc 3535/2240/1632, wc m24 pl 17.13 parts list initial issue pl 17.13 electrical components item part description 1 – pwb cover (not spared) 2 160k76660 finisher pwb (rep 12.16) 3 537k65040 rom (dc2240/1632) – 537k64130 rom (dc3535) 4 – pwb bracket (not spared) 5 962k10120 dc harness 6 962...

  • Page 1063

    09/03 5-90 dc 3535/2240/1632, wc m24 pl 17.14 initial issue parts list pl 17.14 rack assembly item part description 1 802k36660 front rack assembly 2 – front cover (p/o pl 17.14 item 1) 3 003k12090 knob screw 4 – screw (p/o pl 17.14 item 1,pl 17.14 item 11) 5 – bracket (p/o pl 17.14 item 1,pl 17.14 ...

  • Page 1064

    09/03 5-91 dc 3535/2240/1632, wc m24 pl 18.2 parts list initial issue pl 18.2 control panel item part description 1 802k58860 control panel assembly (xe) (wc24) – 802k58870 control panel assembly (xcl) (wc24) – 802k46027 control panel assembly (dc2240/1632) (w/ tag d3) – 802k47297 control panel asse...

  • Page 1065

    09/03 5-92 dc 3535/2240/1632, wc m24 pl 18.3 initial issue parts list pl 18.3 platen glass, iit/ips pwb item part description 1 – right side plate (not spared) 2 090k92820 platen glass (dc2240/1632) (rep 6.2) – 090k02290 platen glass (dc3535) (rep 6.2) 3 050k43070 registration gate (dc2240/1632) – 0...

  • Page 1066

    09/03 5-93 dc 3535/2240/1632, wc m24 pl 18.4 parts list initial issue pl 18.4 ccd pwb, sensor item part description 1 127k33160 ips fan 2 – bracket (not spared) 3 130k62000 iit registration sensor 4 – bracket (not spared) 5 110k08471 platen open switch 6 130k62580 platen angle sensor assembly 7 107e...

  • Page 1067

    09/03 5-94 dc 3535/2240/1632, wc m24 pl 18.5 initial issue parts list pl 18.5 carriage cable/ motor item part description 1 063e94040 tape 2 – frame (not spared) 3 020e99590 pulley 4 012k94110 front carriage cable (rep 6.11) 5 012k94120 rear carriage cable (rep 6.11) 6 063e94050 tape 7 020e32740 tim...

  • Page 1068

    09/03 5-95 dc 3535/2240/1632, wc m24 pl 18.6 parts list initial issue pl 18.6 full/half rate carriage item part description 1 – harness guard (not spared) 2 041k94050 full-rate carriage assembly (adj 6.1) 3 – full-rate carriage (p/o pl 18.6 item 2) 4 117e19780 lamp wire harness (rep 6.14) 5 – no 1 m...

  • Page 1069

    09/03 5-96 dc 3535/2240/1632, wc m24 pl 19.1 initial issue parts list pl 19.1 rack (dc2240/1632/wc24) item part description 1 – rack (not spared) (dc2240/1632/wc24) 2 017e94710 swivel caster (dc2240/1632/wc24) 3 017e94730 stationary caster (dc2240/1632/wc24) 4 017e94700 foot (dc2240/1632/wc24).

  • Page 1070

    09/03 5-97 dc 3535/2240/1632, wc m24 pl 19.2 parts list initial issue pl 19.2 rack (dc3535) item part description 1 – plate assembly (not spared) (dc3535) 2 017e10700 swivel caster (dc3535) 3 017e10710 rear caster (dc3535) 4 017e10840 foot (dc3535) 5 – end cap (not spared) (dc3535) 6 – base support ...

  • Page 1071

    09/03 5-98 dc 3535/2240/1632, wc m24 pl 20.1 initial issue parts list pl 20.1 front/rear cover, entrance tray item part description 1 048k76181 rear cover assembly (rep 5.18) 2 – rear cover (p/o pl 20.1 item 1) 3 140k60480 led pwb 4 – wire harness (p/o pl 20.1 item 1) 5 891e65180 label (display) 6 0...

  • Page 1072

    09/03 5-99 dc 3535/2240/1632, wc m24 pl 20.2 parts list initial issue pl 20.2 top cover, registration gate solenoid item part description 1 054k13622 top cover assembly 2 – top cover (p/o pl 20.2 item 1) 3 015e48890 front magnet plate 4 809e11130 spring 5 059k11880 pinch roll 6 015e48900 front magne...

  • Page 1073

    09/03 5-100 dc 3535/2240/1632, wc m24 pl 20.3 initial issue parts list pl 20.3 counterbalance, dadf control pwb item part description 1 003k91881 thumbscrew 2 036k91431 right counterbalance (rep 5.3) 3 – counterbalance (p/o pl 20.3 item 2) (adj 5.2 adj 5.3 adj 5.4) 4 – dadf interlock switch (p/o pl ...

  • Page 1074

    09/03 5-101 dc 3535/2240/1632, wc m24 pl 20.4 parts list initial issue pl 20.4 document feed chute (upper), feed motor item part description 1 054k13600 document feed upper chute assembly 2 059k11840 feed roll assembly 3 – upper baffle (p/o pl 20.4 item 1) 4 – drive shaft (p/o pl 20.4 item 1) 5 – ge...

  • Page 1075

    09/03 5-102 dc 3535/2240/1632, wc m24 pl 20.5 initial issue parts list pl 20.5 document feed chute (lower) item part description 1 054k18780 lower chute assembly (rep 5.8) 2 – lower chute (p/o pl 20.5 item 1) 3 – spring (p/o pl 20.5 item 1) 4 059k19720 retard roll (rep 5.9) 5 – spring plate (p/o pl ...

  • Page 1076

    09/03 5-103 dc 3535/2240/1632, wc m24 pl 20.6 parts list initial issue pl 20.6 dadf belt motor, duplex roll item part description 1 127k32690 dadf belt motor assembly (rep 5.13) 2 – dadf belt motor (p/o pl 20.6 item 1) 3 – damper (p/o pl 20.6 item 1) 4 – bracket (p/o pl 20.6 item 1) 5 – pulley (p/o ...

  • Page 1077

    09/03 5-104 dc 3535/2240/1632, wc m24 pl 20.7 initial issue parts list pl 20.7 duplex chute item part description 1 – duplex chute (not spared) 2 – wire harness (not spared) 3 130k60600 duplex sensor (rep 5.14) 4 050k46690 gate 5 – screw (not spared) 6 – screw (not spared) 7 054k18790 lower chute as...

  • Page 1078

    09/03 5-105 dc 3535/2240/1632, wc m24 pl 20.8 parts list initial issue pl 20.8 registration roll item part description 1 – spacer (not spared) 2 007k81120 gear pulley 3 – bearing (not spared) 4 059k19750 registration roll 5 012e09760 link 6 809e04210 rear spring 7 005e80250 clip 8 013e94561 bearing ...

  • Page 1079

    09/03 5-106 dc 3535/2240/1632, wc m24 pl 20.9 initial issue parts list pl 20.9 exit motor/chute item part description 1 127k32640 exit motor assembly (rep 5.16) 2 – exit motor (p/o pl 20.9 item 1) 3 – pulley (p/o pl 20.9 item 1) 4 – damper (p/o pl 20.9 item 1) 5 – bracket (p/o pl 20.9 item 1) 6 – sp...

  • Page 1080

    09/03 5-107 dc 3535/2240/1632, wc m24 pl 20.10 parts list initial issue pl 20.10 document transport, platen belt item part description 1 – damper (not spared) 2 – static eliminator (not spared) 3 007e66340 gear 4 – collar (not spared) 5 013e80970 bearing 6 049e91070 tension plate 7 022k39710 idler r...

  • Page 1081

    09/03 5-108 dc 3535/2240/1632, wc m24 pl 20.11 initial issue parts list pl 20.11 platen glass, registration gate, exit tray item part description 1 090k92820 platen glass (dc2240/1632) (rep 6.2) – 090k02290 platen glass (dc3535) (rep 6.2) 2 050k43070 registration gate (dc2240/1632) – 050k48890 regis...

  • Page 1082

    09/03 5-109 dc 3535/2240/1632, wc m24 common hardware parts list initial issue common hardware item part description a 112w27651 screw (m3x6) b 112w27659 screw (m3x6) c 112w27851 screw (m3x8) d 112w28451 screw (m3x14) e 113w20457 screw (m3x4) f 113w20651 screw (m3x6) g 113w20857 screw (m3x8) h 113w2...

  • Page 1083

    09/03 5-110 dc 3535/2240/1632, wc m24 part number index initial issue parts list part number index table 1 part number index part number part list 001e59600 pl 17.9 001e60050 pl 17.14 001k70542 pl 5.1 001k70551 pl 5.1 003k12090 pl 17.1 pl 17.14 003k12650 pl 5.2 003k12881 pl 5.1 003e23672 pl 15.1 pl ...

  • Page 1084

    09/03 5-111 dc 3535/2240/1632, wc m24 part number index parts list initial issue pl 15.5 pl 16.7 pl 16.9 pl 2.4 007k85750 pl 1.1 007k86400 pl 1.1 007k86700 pl 20.6 007k86910 pl 17.6 007k86921 pl 1.1 007k86931 pl 2.9 007k87220 pl 1.1 007k87360 pl 1.1 007k87370 pl 1.1 007k87440 pl 2.9 007k87600 pl 1.1...

  • Page 1085

    09/03 5-112 dc 3535/2240/1632, wc m24 part number index initial issue parts list 019k97540 pl 5.4 019k97550 pl 5.4 019k98190 pl 5.4 019k98200 pl 5.4 020e21050 pl 20.6 020e25090 pl 18.5 020e32740 pl 18.5 020e34970 pl 17.8 020k91230 pl 20.6 020e93120 pl 16.3 020e93230 pl 20.9 020k94970 pl 18.6 020e995...

  • Page 1086

    09/03 5-113 dc 3535/2240/1632, wc m24 part number index parts list initial issue 054k22410 pl 2.8 055k19260 pl 20.5 055k26060 pl 20.9 059k11821 pl 20.9 059k11840 pl 20.4 059k11860 pl 20.9 059k11880 pl 20.2 059k15573 pl 15.1 pl 16.6 pl 2.3 059k15612 pl 2.8 059k16742 pl 11.1 059k18283 pl 16.5 059k1871...

  • Page 1087

    09/03 5-114 dc 3535/2240/1632, wc m24 part number index initial issue parts list 110e93440 pl 12.2 110e94770 pl 10.1 110e97990 pl 10.1 pl 17.13 113k82310 pl 9.3 116k90810 pl 6.1 117e19780 pl 18.6 117e20840 pl 18.3 117k30960 pl 18.4 117k31400 pl 9.2 117k34640 pl 9.4 117e94370 pl 9.2 118e12090 pl 18.6...

  • Page 1088

    09/03 5-115 dc 3535/2240/1632, wc m24 part number index parts list initial issue 130k60851 pl 2.3 130k60865 pl 1.3 130k61020 pl 7.2 130k61250 pl 12.2 130k61510 pl 15.10 pl 16.6 130k61920 pl 17.6 130k62000 pl 18.4 130k62360 pl 17.4 130k62580 pl 18.4 130k62980 pl 9.4 130k63000 pl 6.2 130e80890 pl 20.5...

  • Page 1089

    09/03 5-116 dc 3535/2240/1632, wc m24 part number index initial issue parts list 160k93514 pl 18.2 160k94002 pl 18.3 160k98020 pl 18.3 160k98890 pl 18.2 160k99040 pl 18.2 160k99050 pl 18.2 160k99070 pl 13.1 162k55941 pl 9.3 162k55971 pl 9.3 162k56000 pl 9.3 162k56020 pl 5.4 162k56031 pl 9.3 162k5659...

  • Page 1090

    09/03 5-117 dc 3535/2240/1632, wc m24 part number index parts list initial issue 802e28550 pl 17.5 802e28560 pl 17.5 802e28570 pl 17.5 802k28571 pl 17.6 802k28580 pl 17.4 802k28590 pl 17.3 802k28600 pl 17.3 802k28810 pl 6.1 802k28820 pl 6.1 802k28830 pl 6.1 802k28840 pl 6.1 802k28891 pl 6.2 802k2961...

  • Page 1091

    09/03 5-118 dc 3535/2240/1632, wc m24 part number index initial issue parts list pl 16.1 892e89310 pl 20.1 892e89340 pl 20.1 892e90351 pl 15.2 pl 2.2 908w01200 pl 9.2 960k11380 pl 10.3 962k03490 pl 9.4 962k03500 pl 9.4 962k03981 pl 9.4 962k05900 pl 18.4 962k05910 pl 18.4 962k07440 pl 17.9 962k08641 ...

  • Page 1092

    09/03 6-1 dc 3535/2240/1632, wc m24 general procedures and information initial issue 6 general procedures & information diagnostics (dc100-dc129) entering diagnostic mode using the pws ...................................................................... 6-3 ui diagnostic mode ........................

  • Page 1093

    09/03 6-2 dc 3535/2240/1632, wc m24 initial issue general procedures and information.

  • Page 1094

    09/03 6-3 dc 3535/2240/1632, wc m24 entering diagnostic mode using the pws general procedures and information initial issue entering diagnostic mode using the pws procedure the following procedure describe how to enter the diagnostics mode with the pws. 1. Inform the customer that the machine will b...

  • Page 1095

    09/03 6-4 dc 3535/2240/1632, wc m24 ui diagnostic mode initial issue general procedures and information ui diagnostic mode diagnostic routines are mainly instructed/executed through the pws. The ui diagnostic mode is provided for simple tasks that do not require connection with the pws. Procedure ac...

  • Page 1096

    09/03 6-5 dc 3535/2240/1632, wc m24 dc quick general procedures and information initial issue dc quick (code number list) once in the service mode, dc routines can be selected by dc number or by selecting the appropriate tabs starting at the service entry screen. Procedure 1. Enter the diagnostic mo...

  • Page 1097

    09/03 6-6 dc 3535/2240/1632, wc m24 dc quick, dc100 initial issue general procedures and information dc100 service entry when entering diagnostics, this routine allows you to view faults in progress, non-zero jams and hfsi items requiring replacement. Service entry allows you to view product informa...

  • Page 1098

    09/03 6-7 dc 3535/2240/1632, wc m24 dc118, dc120 general procedures and information initial issue dc118 jam counter purpose displays the number of occurrences of jams from time of previous complete closeout on ser- vice exit until present. Note: this procedure does not count jams detected while in t...

  • Page 1099

    09/03 6-8 dc 3535/2240/1632, wc m24 dc122, dc129 initial issue general procedures and information dc122 shutdown history purpose to display the last 40 faults (history). Note: 1. Faults detected while in service mode are not counted. 2. An interlock open while the machine is stopped is not counted. ...

  • Page 1100

    09/03 6-9 dc 3535/2240/1632, wc m24 dc131 general procedures and information initial issue dc131 nvm read/write purpose reads, sets or changes the nvm data. Procedure module selection 1. Enter the diagnostic mode. Refer to entering diagnostic mode using the pws . 2. Select adjustments in the service...

  • Page 1101

    09/03 6-10 dc 3535/2240/1632, wc m24 700-xxx ess configuration nvm list initial issue general procedures and information 700-xxx ess configuration nvm list table 1 chain 700 chain-link name default range description 700-006 configuration - 0~8 [p, sp, csp, cfsp] set up at factory production. It allo...

  • Page 1102

    09/03 6-11 dc 3535/2240/1632, wc m24 700-xxx ess configuration nvm list general procedures and information initial issue 700-130 sleep mode timer 60 15~240 15~240min (in increments of 1 min.) 700-131 sleep mode available 1 0~1 0=disable; 1=enable 700-132 operation panel ok beep 2 0~3 0=off; 1=low vo...

  • Page 1103

    09/03 6-12 dc 3535/2240/1632, wc m24 700-xxx ess configuration nvm list initial issue general procedures and information 700-176 fax report language #1 2 1~13 1 = japanese, 2 = english, 3 = french, 4 = german, 5 = italian, 6 = spanish, 7 = portuguese, 8 = russian, 9 = chinese, 10 = korean, 11 = thai...

  • Page 1104

    09/03 6-13 dc 3535/2240/1632, wc m24 700-xxx ess configuration nvm list general procedures and information initial issue 700-321 seeprom product # (1st digit) - - alphanumeric (ascii) 700-322 seeprom product # (2nd digit) - - alphanumeric (ascii) 700-323 seeprom product # (3rd digit) - - alphanumeri...

  • Page 1105

    09/03 6-14 dc 3535/2240/1632, wc m24 700-xxx ess configuration nvm list initial issue general procedures and information 700-357 ui control rom major - - (auto setting) 700-358 ui control rom minor - - (auto setting) 700-359 ui control rom revision - - (auto setting) 700-360 product code (1st digit)...

  • Page 1106

    09/03 6-15 dc 3535/2240/1632, wc m24 701--xxx image quality setting nvm list, 710-xxx general procedures and information initial issue 701--xxx image quality setting nvm list 710-xxx dadf nvm list table 1 chain 701 chain-link name default range description 701-912 adc gradation compensation validity...

  • Page 1107

    09/03 6-16 dc 3535/2240/1632, wc m24 710-xxx dadf nvm list initial issue general procedures and information 710-803 adf document input sensor static jam count since reset 0 0~65535 cumulative jam counter at the previous clearing (write not permitted) 710-804 adf registration sensor static jam count ...

  • Page 1108

    09/03 6-17 dc 3535/2240/1632, wc m24 715-xxx iit nvm list general procedures and information initial issue 715-xxx iit nvm list table 1 chain 715 chain-link name default range description 715-001 preips fail bypass 0 0~1 0=fail bypass is not available; 1=fail bypass is available 715-004 acs detectio...

  • Page 1109

    09/03 6-18 dc 3535/2240/1632, wc m24 715-xxx iit nvm list initial issue general procedures and information 715-214 undercolor data for b/w 0 0~255 speed priority ae/fixed background color data in b/w register mode 715-215 undercolor data for color 0 0~255 speed priority ae/fixed background color dat...

  • Page 1110

    09/03 6-19 dc 3535/2240/1632, wc m24 715-xxx iit nvm list general procedures and information initial issue 715-247 b/w-offset for text/image dadf single side mode (real time ae) 13 0~255 for ae offset data dadf single side document text/photo in b/w model 715-248 b/w-offset for text dadf single side...

  • Page 1111

    09/03 6-20 dc 3535/2240/1632, wc m24 715-xxx iit nvm list initial issue general procedures and information 715-804 eeprom failure count overall total 0 0~65535 cumulative fail counter (write not permitted) 715-805 eeprom failure count since reset 0 0~65535 cumulative fail counter at the previous cle...

  • Page 1112

    09/03 6-21 dc 3535/2240/1632, wc m24 715-xxx iit nvm list general procedures and information initial issue 715-829 platen agc channel 4 fail count since reset 0 0~65535 cumulative fail counter at the previous clearing (write not permitted) 715-830 platen agc channel 5 fail count overall total 0 0~65...

  • Page 1113

    09/03 6-22 dc 3535/2240/1632, wc m24 715-xxx iit nvm list, 719--xxx iit/dadf software initial issue general procedures and information 719--xxx iit/dadf software nvm list 720-xxx ess meter/counter nvm list 715-859 dadf ram check failures since reset 0 0~65535 cumulative fail counter at the previous ...

  • Page 1114

    09/03 6-23 dc 3535/2240/1632, wc m24 720-xxx ess meter/counter nvm list, 740--xxx iot general procedures and information initial issue 740--xxx iot manager nvm list 741--xxx drive nvm list 720-016 backup1 copy-full color - 0~1999999 read only 720-017 backup1 copy-color2 - 0~1999999 read only 720-018...

  • Page 1115

    09/03 6-24 dc 3535/2240/1632, wc m24 741--xxx drive nvm list initial issue general procedures and information 741-112 3535 only ibt motor reverse switch 1 0~1 switch to reverse ibt motor rotation at job end 0=disable; 1=enable 741-113 3535 only pr motor reverse switch 0 0~1 switch to reverse pr moto...

  • Page 1116

    09/03 6-25 dc 3535/2240/1632, wc m24 742--xxx paper handling nvm list general procedures and information initial issue 742--xxx paper handling nvm list table 1 chain 742 chain-link name default range description 742-001 invert clutch cw off timing 91 0~163 paper inversion position adjustment (p spee...

  • Page 1117

    09/03 6-26 dc 3535/2240/1632, wc m24 742--xxx paper handling nvm list initial issue general procedures and information 742-026 adjust side regi (tray 5) 20 0~50 side regi adjustment (tray 5) (1bit=0.211mm) 742-027 adjust side regi (dup) * 0~50 side regi adjustment (dup) (1bit=0.211mm) *default=18 fo...

  • Page 1118

    09/03 6-27 dc 3535/2240/1632, wc m24 742--xxx paper handling nvm list general procedures and information initial issue 742-058 pre-t/a start timing ttm-tray 2 10 0~16 adjusts the time between pre-t/a starts and standard signal (iot) (1bit=2.4462 msec.) 742-059 pre-t/a start timing ttm-tray 3 74 0~11...

  • Page 1119

    09/03 6-28 dc 3535/2240/1632, wc m24 742--xxx paper handling nvm list initial issue general procedures and information 742-094 dc3535 pre-t/a start timing 3tm-tray 3 118 0~183 adjusts the time between pre-t/a starts and standard signal (iot) (365~865 msec.) (1bit=1.5418 msec.) 742-095 dc2240/1632 pr...

  • Page 1120

    09/03 6-29 dc 3535/2240/1632, wc m24 742--xxx paper handling nvm list general procedures and information initial issue 742-110 pre-t/a start timing ttm-tray 4 (half) 37 0~58 adjusts the time between pre-t/a starts and standard signal (iot) (431~931 msec.) (1bit=4.8924 msec.) 742-111 main feed start ...

  • Page 1121

    09/03 6-30 dc 3535/2240/1632, wc m24 744--xxx fuser nvm list initial issue general procedures and information 744--xxx fuser nvm list table 1 chain 744 chain-link name default range description 744-001 sts-1 cont temp- low pwr mode 80 0~160 (1 bit=1 deg. C) main-lamp temperature control in low-power...

  • Page 1122

    09/03 6-31 dc 3535/2240/1632, wc m24 744--xxx fuser nvm list general procedures and information initial issue 744-050 dc3535 only sts-2 target run temperature#22 140 100~200 for optimization of temperature distribution - transparency sef (1 bit=1 deg.C). 744-051 environment temperature correction 3 ...

  • Page 1123

    09/03 6-32 dc 3535/2240/1632, wc m24 744--xxx fuser nvm list initial issue general procedures and information 744-196 dc2240/1632 only plain paper s setting temperature 2 0~2 0=light weight paper (55~63gsm) 1=plain paper (64~80gsm) 2=bond (81~105gsm) 744-197 104mm/sec. Ohp pitch adjustment value 0 0...

  • Page 1124

    09/03 6-33 dc 3535/2240/1632, wc m24 744--xxx fuser nvm list general procedures and information initial issue 744-239 dc3535 only applied time for 104mm/sec. Ohp skip modetarget run temp.(t[run#4]) 6 1~100 (1 bit=5 sec.) 744-239 dc3535 only applied time for 104mm/sec. Ohp skip modetarget run temp.(t...

  • Page 1125

    09/03 6-34 dc 3535/2240/1632, wc m24 746--xxx xero transfer nvm list initial issue general procedures and information 746--xxx xero transfer nvm list table 1 chain 746 chain-link name default range description 746-006 dc2240/1632 2nd resistance detection calculation results 245 102~921 (1bit=-4.888v...

  • Page 1126

    09/03 6-35 dc 3535/2240/1632, wc m24 746--xxx xero transfer nvm list general procedures and information initial issue 746-028 1st btr output remote half-speed fc k 36 0~200 (1bit=1%) for primary transfer output adjustment of k color at fc52mmsec. Displays the multiplication value in primary transfer...

  • Page 1127

    09/03 6-36 dc 3535/2240/1632, wc m24 746--xxx xero transfer nvm list initial issue general procedures and information 746-072 remote for transparency side1 100 0~200 (1bit=1%) for secondary transfer output adjustment of transparency side 1. Displays the multiplication value in second- ary transfer r...

  • Page 1128

    09/03 6-37 dc 3535/2240/1632, wc m24 746--xxx xero transfer nvm list general procedures and information initial issue 746-091 plain paper s control nvm1 (bw side1) 0 0~1 0=control -s-7 (for bw side 1 of plain paper a~g) 1=control -s-8 (for bw side 1 of paper applicable to the above) 746-092 plain pa...

  • Page 1129

    09/03 6-38 dc 3535/2240/1632, wc m24 746--xxx xero transfer nvm list initial issue general procedures and information 746-967 1st btr vmonitor y 36 4~178 displays the voltage at primary transfer resistance detection (100~5000v - 1bit=28.01v) 746-968 1st btr vmonitor m 36 4~178 displays the voltage a...

  • Page 1130

    09/03 6-39 dc 3535/2240/1632, wc m24 747--xxx transfer nvm list general procedures and information initial issue 747--xxx transfer nvm list (dc 3535 only) table 1 chain 747 chain- link name default range description 747-417 dts present output 818 0~818 display environment * remote (3.666v/bit) 747-4...

  • Page 1131

    09/03 6-40 dc 3535/2240/1632, wc m24 747--xxx transfer nvm list initial issue general procedures and information 747-441 2nd btr output remote/normal speed/ side1/heavy paper 1b 100 0~200 for 2nd transfer output adjustment for heavy paper 1b side1. (multiply by 2nd transfer resistance calculation re...

  • Page 1132

    09/03 6-41 dc 3535/2240/1632, wc m24 747--xxx transfer nvm list general procedures and information initial issue 747-462 high speed 1st transfer b/w k ecc #4 1000 0~2000 environment control coefficient of 1st transfer output for k ex.: in case of 1000: µa=((value in 746-020)+(value in 746-303))x(val...

  • Page 1133

    09/03 6-42 dc 3535/2240/1632, wc m24 747--xxx transfer nvm list, 751--xxx procon nvm initial issue general procedures and information 751--xxx procon nvm list 747-483 low speed 1st transfer b/w k ecc #7 1000 0~2000 environment control coefficient of 1st transfer output for k ex.: in case of 1000: µa...

  • Page 1134

    09/03 6-43 dc 3535/2240/1632, wc m24 752-xxx procon nvm list general procedures and information initial issue 752-xxx procon nvm list table 1 chain 752 chain-link name default range description 752-027 vdark average 0 0~1023 adc average detected value at expansion led off. 752-028 vref average 0 0~1...

  • Page 1135

    09/03 6-44 dc 3535/2240/1632, wc m24 752-xxx procon nvm list initial issue general procedures and information 752-081 atc average [y] 0 0~1023 atc average detected value after sensor sensitivity correction 752-082 atc average [m] 0 0~1023 atc average detected value after sensor sensitivity correctio...

  • Page 1136

    09/03 6-45 dc 3535/2240/1632, wc m24 752-xxx procon nvm list general procedures and information initial issue 752-156 atc control nominal value [y] 500 0~1023 [set atc control nominal value]+[atc environment correction value]+[atc deterioration correction value]+[atc nominal value offset] 752-157 at...

  • Page 1137

    09/03 6-46 dc 3535/2240/1632, wc m24 752-xxx procon nvm list initial issue general procedures and information 752-441 warn ld light amount setting [c] 0 0~1 warning when the laser diode light quantity reached upper or lower limit. 752-442 warn ld light amount setting [k] 0 0~1 warning when the laser...

  • Page 1138

    09/03 6-47 dc 3535/2240/1632, wc m24 752-xxx procon nvm list general procedures and information initial issue 752-873 dc3535 only sw charge potential control on/off 0 0~1 0=control vh (add delta-vh to vh according to ld illumination; 1=no control for vh (delta-vh=0) 752-934 dc3535 only radc nominal ...

  • Page 1139

    09/03 6-48 dc 3535/2240/1632, wc m24 753-xxx procon 2 nvm list initial issue general procedures and information 753-xxx procon 2 nvm list table 1 chain 753 chain-link name default range description 753-001 adc tone correction switch 0 0~1 2 patch adc gradation correction. On/off switch (0=on, 1=off)...

  • Page 1140

    09/03 6-49 dc 3535/2240/1632, wc m24 753-xxx procon 2 nvm list general procedures and information initial issue 753-029 trc target radc [k] [b] * 0~1023 target radc for gradation correction *default=310 for dc2240/1632; 460 for dc3535 753-030 trc current radc [y] [a] * 0~1023 current radc for gradat...

  • Page 1141

    09/03 6-50 dc 3535/2240/1632, wc m24 753-xxx procon 2 nvm list initial issue general procedures and information 753-840 dc3535 only trc_target radc [y] [fc] 0 0~1023 current radc for tone calibration 753-841 dc3535 only trc_target radc [m] [c] 0 0~1023 current radc for tone calibration 753-842 dc353...

  • Page 1142

    09/03 6-51 dc 3535/2240/1632, wc m24 755-xxx crum nvm list general procedures and information initial issue 755-xxx crum nvm list table 1 chain 755 chain-link name default range description 755-001 #y_drum life count - kcy 0 * to determine drum life * range=0~3000 for dc 2240/1632; 0~65535 for dc 35...

  • Page 1143

    09/03 6-52 dc 3535/2240/1632, wc m24 755-xxx crum nvm list initial issue general procedures and information 755-036 #m_shutdown count - full color 0 0~65535 accumulates the # of shutdowns during fc jobs. 755-037 #m_shutdown count - black 0 0~65535 accumulates the # of shutdowns during b/w jobs. 755-...

  • Page 1144

    09/03 6-53 dc 3535/2240/1632, wc m24 755-xxx crum nvm list general procedures and information initial issue 755-083 #k_drum cycle count - total 0 0~ 4294967295 cumulative # of p/r cycles (1bit=0.1cycle) 755-084 #k_dc drum cycle count 0 0~ 4294967295 cumulative # of dc charge current p/r cycles (1bit...

  • Page 1145

    09/03 6-54 dc 3535/2240/1632, wc m24 755-xxx crum nvm list initial issue general procedures and information 755-210 dc3535 only #y_area coverage count, 4c (51- 100%) 0 0~65535 area coverage counter for 4c (51-100%) (1 bit=1 page) 755-211 dc3535 only #y_cru install - color 0 0~4 y=1; m=2; 3=c; 4=k 75...

  • Page 1146

    09/03 6-55 dc 3535/2240/1632, wc m24 755-xxx crum nvm list general procedures and information initial issue 755-410 dc3535 only #c_area coverage count, 4c (51- 100%) 0 0~65535 area coverage counter for 4c (51-100%) (1 bit=1 page) 755-411 dc3535 only #c_cru install - color 0 0~4 y=1; m=2; 3=c; 4=k 75...

  • Page 1147

    09/03 6-56 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list initial issue general procedures and information 760-xxx regicon nvm list table 1 chain 760 chain-link name default range description 760-001 dc3535 lposi 3004 0~3004 permissible misregistration between the center of optical axis of mob s...

  • Page 1148

    09/03 6-57 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list general procedures and information initial issue 760-026 k-yso 237 0~474 adjusts the slow scan direction write start position by the #. Of ls signal counts from the ros/image/patch start signal. (1 pixel/bit) 760-027 regi con/circum. Leng...

  • Page 1149

    09/03 6-58 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list initial issue general procedures and information 760-050 m-xbi 0 0~3 adjusts fast scan direction write start position by switching the video clock phase from sos signal. (dc 2240/1632=1 pixel/bit; dc 3535=1/5 pixel/bit) 760-051 c-xbi 0 0~...

  • Page 1150

    09/03 6-59 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list general procedures and information initial issue 760-060 k-olxbi 0 0~3 adjust writing-start position in fs direction in open loop, by switching video lock phase from sos signal, based on temperature detection results, separately from norm...

  • Page 1151

    09/03 6-60 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list initial issue general procedures and information 760-069 dc3535 skew alarm threshold 30 0~255 threshold of skew amount; if this value is exceeded, it is registered as a failure. (2µm/bit) 760-070 y-ld light volume at last regicon 0 0~1023...

  • Page 1152

    09/03 6-61 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list general procedures and information initial issue 760-101 dc3535 m-y margin speed switch variation 138 0~200 (y margin variation amount when the speed is switched from 104 or 52mm/sec. To 165mm/sec.)-100, for magenta (1 µm/bit) 760-102 dc3...

  • Page 1153

    09/03 6-62 dc 3535/2240/1632, wc m24 760-xxx regicon nvm list initial issue general procedures and information 760-122 dc3535 register set value for yso-ros at y 165mm/s 237 0~474 ps register set value; for debugging 760-123 dc3535 register set value for yso-ros at m 165mm/s 237 0~474 ps register se...

  • Page 1154

    09/03 6-63 dc 3535/2240/1632, wc m24 762-xxx developer nvm list general procedures and information initial issue 762-xxx developer nvm list table 1 chain 762 chain-link name default range description 762-002 #ymc normal vm1 value 351 0~1023 (1bit=-0.684v) vm1 developer dc energized voltage at ymc co...

  • Page 1155

    09/03 6-64 dc 3535/2240/1632, wc m24 762-xxx developer nvm list initial issue general procedures and information 762-061 ac bias normal test value 0 0~100 ac voltage test value at normal speed 762-062 ac bias normal frequency 60 0~127 ac voltage frequency at normal speed 762-064 #ym_db ac half-speed...

  • Page 1156

    09/03 6-65 dc 3535/2240/1632, wc m24 762-xxx developer nvm list general procedures and information initial issue 762-102 #m_db dc vm1 off half speed timing 92 0~255 fall timing from vm1 to vm0 for m color half speed. (1bit=4.8924 msec.) 762-103 #c_db dc vm1 off half speed timing 92 0~255 fall timing...

  • Page 1157

    09/03 6-66 dc 3535/2240/1632, wc m24 762-xxx developer nvm list, 764-xxx output (finish- initial issue general procedures and information 764-xxx output (finisher) nvm list 762-232 #ym_db ac hi-speed output phase value 65 0~127 ac energized voltage phase value at ym color high speed. 762-233 #ck_db ...

  • Page 1158

    09/03 6-67 dc 3535/2240/1632, wc m24 762-xxx developer nvm list, 764-xxx output (fin- general procedures and information initial issue.

  • Page 1159

    09/03 6-68 dc 3535/2240/1632, wc m24 770-xxx ess io port/protocol setting nvm list initial issue general procedures and information 770-xxx ess io port/protocol setting nvm list table 1 chain 770 chain-link name default range description 770-001 parallel port enable 1 0~1 0=stop 1=start up 770-002 p...

  • Page 1160

    09/03 6-69 dc 3535/2240/1632, wc m24 770-xxx ess io port/protocol setting nvm list general procedures and information initial issue 770-090 ipp port enable 1 0~1 0=stop; 1=start up 770-091 ipp print mode type 1 - 1=auto; 3=hpgl2; 5=postscript; 8=escp; 10=tiff; 16=art; 17=plw; 23=dump 770-092 ipp jcl...

  • Page 1161

    09/03 6-70 dc 3535/2240/1632, wc m24 780-xxx ess print frame setting nvm list initial issue general procedures and information 780-xxx ess print frame setting nvm list table 1 chain 780 chain-link name default range description 780-013 dc2240/1632 paper type for tray 1 22 1~27 1=plain paper; 2=trans...

  • Page 1162

    09/03 6-71 dc 3535/2240/1632, wc m24 780-xxx ess print frame setting nvm list general procedures and information initial issue 780-036 image quality control category - heavy weight 2 paper 27 4~31 27=heavy weight 2a; 28=gloss 1c; 29=gloss 1a; 30=coated 1 gloss; 31=heavy weight 2s 780-037 image quali...

  • Page 1163

    09/03 6-72 dc 3535/2240/1632, wc m24 785-xxx ess fax setting nvm list initial issue general procedures and information 785-xxx ess fax setting nvm list table 1 chain 785 chain-link name default range description 785-002 acs separate level 3 0~5 1= black, 2: towards black, 3: normal, 4: towards color...

  • Page 1164

    09/03 6-73 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list general procedures and information initial issue 790-xxx ess panel display setting nvm list table 1 chain 790 chain-link name default range description 790-001 startup display setting 0 0~2 0=features programming screen;...

  • Page 1165

    09/03 6-74 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list initial issue general procedures and information 790-013 tray 5 paper sizes _8 13 0~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef; 13=a3sef; 14=postca...

  • Page 1166

    09/03 6-75 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list general procedures and information initial issue 790-092 default dual color selection (“vivid” color) 0 0~12 1~6=fixed registered color 1~6; 7~12=user registered color 1~6 790-093 default dual color selection (chro- mati...

  • Page 1167

    09/03 6-76 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list initial issue general procedures and information 790-132 fixed size 2 of copy document size input 15 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef; ...

  • Page 1168

    09/03 6-77 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list general procedures and information initial issue 790-141 fixed size 11 of copy document size input 28 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef;...

  • Page 1169

    09/03 6-78 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list initial issue general procedures and information 790-211 fixed size 2 of fax scan size input 10 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef; 13=a3...

  • Page 1170

    09/03 6-79 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list general procedures and information initial issue 790-220 fixed size 11 of fax scan size input 18 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef; 13=a...

  • Page 1171

    09/03 6-80 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list initial issue general procedures and information 790-236 fixed size 6 of scan document size input 22 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4lef; 12=b4sef; ...

  • Page 1172

    09/03 6-81 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list general procedures and information initial issue 790-265 fixed size 8 slow scan null 15~432 15~432mm 790-266 fixed size 9 fast scan null 15~297 15~297mm 790-267 fixed size 9 slow scan null 15~432 15~432mm 790-268 fixed s...

  • Page 1173

    09/03 6-82 dc 3535/2240/1632, wc m24 790-xxx ess panel display setting nvm list, 800-xxx initial issue general procedures and information 800-xxx ess print service setting 790-287 output size 8 7 1~50 1=postcard; 2=a6sef; 3=a6lef; 4=b6sef; 5=b6lef; 6=a5sef; 7=a5lef; 8=b5sef; 9=b5lef; 10=a4sef; 11=a4...

  • Page 1174

    09/03 6-83 dc 3535/2240/1632, wc m24 810-xxx ess copy service setting general procedures and information initial issue 810-xxx ess copy service setting table 1 chain 810 chain/link name default range description 810-002 fixed preset color1 (red) y component 102 (80%) 0~128 0%~100%; 0.78%/bit 810-003...

  • Page 1175

    09/03 6-84 dc 3535/2240/1632, wc m24 810-xxx ess copy service setting initial issue general procedures and information 810-027 user preset color 3 - m component 0 0~128 0%~100%; 0.78%/bit 810-028 user preset color 3 - c component 0 0~128 0%~100%; 0.78%/bit 810-029 user preset color 4 - y component 0...

  • Page 1176

    09/03 6-85 dc 3535/2240/1632, wc m24 810-xxx ess copy service setting general procedures and information initial issue 810-063 color balance (m high density) meri- hari copy 6 0~6 0=lighter 3; 1=lighter 2; 2=lighter 1; 3=normal; 4=darker 1; 5=darker 2; 6=darker 3 810-064 color balance (c low density...

  • Page 1177

    09/03 6-86 dc 3535/2240/1632, wc m24 810-xxx ess copy service setting initial issue general procedures and information 810-088 color shift - ruddiness 2 0~4 0=-20 degrees; 1=-10 degrees; 2=0 degrees; 3=+10 degrees; 4=+20 degrees 810-089 color saturation - ruddiness 2 0~4 0=higher 2; 1=higher 1; 2=no...

  • Page 1178

    09/03 6-87 dc 3535/2240/1632, wc m24 810-xxx ess copy service setting general procedures and information initial issue 810-128 operation when memory overflow occurs 0 0~1 0=stop; 1=print 810-129 max. No. Of copy sheets accumulated 999 1~999 1-999=[1~999 pages] 810-130 build job setup menu display 1 ...

  • Page 1179

    09/03 6-88 dc 3535/2240/1632, wc m24 820-xxx ess fax service function setting nvm list initial issue general procedures and information 820-xxx ess fax service function setting nvm list table 1 chain 820 chain/link name default range description 820-003 full dial disable 0 0~1 0 = enable; 1 = disabl...

  • Page 1180

    09/03 6-89 dc 3535/2240/1632, wc m24 823-xxx ess fax service device setting nvm list general procedures and information initial issue 823-xxx ess fax service device setting nvm list table 1 chain 823 chain/link name default range description 823-001 receive mode setting 0 0~1 0 = auto receive (auto ...

  • Page 1181

    09/03 6-90 dc 3535/2240/1632, wc m24 823-xxx ess fax service device setting nvm list, initial issue general procedures and information 825-xxx ess fax service protocol setting nvm list 823-041 line type for ch5 0 0~2 0 = pstn (public telephone network); 1 = pbx (private branch exchange); 2 = direct ...

  • Page 1182

    09/03 6-91 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm general procedures and information initial issue 825-054 pb send level (high-pass - low-pass (db)) for ch2 0 0~15 0=2.0; 1=2.5; 2=3.0; 3=3.5; 4=4.0; 5=4.5; 6=5.0; 7=5.5; 8=-2.0; 9=-1.5; 10=-1.0; 11=-0.5; 12=0; 13=0.5;1...

  • Page 1183

    09/03 6-92 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm list initial issue general procedures and information 825-076 timing of tone detection before dialing for ch5 10 0~255 0 ~ 255 (sec) 825-077 call restriction for ch0 0 0~2 0= outgoing/incoming call; 1= outgoing call on...

  • Page 1184

    09/03 6-93 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm general procedures and information initial issue 825-165 fsk detection before image information is received 0 0~1 0= off; 1= on 825-166 g3m csi send 0 0~1 transmit=0; off=1. Csi = notification signal to the sender of t...

  • Page 1185

    09/03 6-94 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm list initial issue general procedures and information 825-194 ecm ctc speed shift down for ch3 1 0~1 0 = no shift; 1 = shift down. (ctc= instructs to continue resending for the same block and to change the trans- missi...

  • Page 1186

    09/03 6-95 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm general procedures and information initial issue 825-223 g3 modem rx communication speed capability (v.34) for channel 2 14 1~14 14 = 33600 bps (1110); 31200 bps (1101); 28800 bps (1100); 26400 bps (1011); 24000 bps (1...

  • Page 1187

    09/03 6-96 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm list initial issue general procedures and information 825-241 g3 modem tx communication speed capability (v.34) for channel 2 14 1~14 14 = 33600 bps (1110); 31200 bps (1101); 28800 bps (1100); 26400 bps (1011); 24000 b...

  • Page 1188

    09/03 6-97 dc 3535/2240/1632, wc m24 825-xxx ess fax service protocol setting nvm general procedures and information initial issue 825-261 g3 tsi/cig send tsi for ch4 0 0~255 0 = auto; 1 = forced transmit; 10 = not transmit. Notification signal of the sender id by the signal for the csi signal from ...

  • Page 1189

    09/03 6-98 dc 3535/2240/1632, wc m24 830-xxx ess i-fax service control nvm list, 840-xxx initial issue general procedures and information 830-xxx ess i-fax service control nvm list 840-xxx ess scan setting nvm list table 1 chain 830 chain/link name default range description 830-001 email to print (i...

  • Page 1190

    09/03 6-99 dc 3535/2240/1632, wc m24 840-xxx ess scan setting nvm list general procedures and information initial issue 840-012 med. Soft contrast (slightly low) 75 0~200 0~200=[-100~100] 840-013 soft contrast (low) 50 0~200 0~200=[-100~100] 840-014 scan to e-mail enable (wc 24 only) 0 0~1 0=disable...

  • Page 1191

    09/03 6-100 dc 3535/2240/1632, wc m24 850-xxx ess foreign interface nvm list initial issue general procedures and information 850-xxx ess foreign interface nvm list table 1 chain 840 chain/link name default range description 850-001 foreign interface enable 0 0~1 0 = enable; 1 = disable 850-009 prin...

  • Page 1192

    09/03 6-101 dc 3535/2240/1632, wc m24 870-xxx ess diagnosis setting nvm list general procedures and information initial issue 870-xxx ess diagnosis setting nvm list table 1 chain 870 chain/link name default range description 870-001 tbd normal - normal, diag (auto setting) 870-010 cru #1 pr wear pre...

  • Page 1193

    09/03 6-102 dc 3535/2240/1632, wc m24 870-xxx ess diagnosis setting nvm list initial issue general procedures and information.

  • Page 1194

    09/03 6-103 dc 3535/2240/1632, wc m24 dc132, dc135 general procedures and information initial issue dc132 serial number/billing meter synchronization purpose checks the billing meters and sets the machine serial number when fault 103-208 occurs. This routine also reads the billing meters and can be ...

  • Page 1195

    09/03 6-104 dc 3535/2240/1632, wc m24 dc140, dc188 initial issue general procedures and information dc140 analog monitor purpose monitors the analog values of the a/d converter sensors by driving each component (e.G.;, c.C). Temporary change of output values is possible. Output component check is al...

  • Page 1196

    09/03 6-105 dc 3535/2240/1632, wc m24 dc301 general procedures and information initial issue dc301 nvm initialization purpose this procedure may be needed when the machine cannot recover for some unknown reasons, including problems such as producing blank copies/prints, continuously declaring system...

  • Page 1197

    09/03 6-106 dc 3535/2240/1632, wc m24 dc305, dc330 initial issue general procedures and information dc305 ui component check purpose checks the operations of the ui screen and control panel buttons. Procedure 1. Enter the diagnostic mode. Refer to entering diagnostic mode using the pws . 2. Select t...

  • Page 1198

    09/03 6-107 dc 3535/2240/1632, wc m24 dc330 general procedures and information initial issue note: when exiting dc330, the machine resets and communication between the pws and the machine is momentarily lost. The pws will reconnect automatically. Table 1 input component control codes code name descr...

  • Page 1199

    09/03 6-108 dc 3535/2240/1632, wc m24 dc330 initial issue general procedures and information 009-101 toner_y new cru connection of color is open (the cru in use is present, or it is not present). Low=new, high=old 009-102 toner_m new cru connection of color is open (the cru in use is present, or it ...

  • Page 1200

    09/03 6-109 dc 3535/2240/1632, wc m24 dc330 general procedures and information initial issue 004-011 drum motor ymc (52mm/sec.) rotate at low speed. Remove all drum car- tridges before energizing to prevent belt damage. 004-003 004-012 ibt motor (52mm/ sec.) rotate at low speed. Operate with the ibt...

  • Page 1201

    09/03 6-110 dc 3535/2240/1632, wc m24 dc330 initial issue general procedures and information 008-011 dup motor (200.1mm/sec.) long 8-009, 010, 012, 053, 054, 055, 056 008-012 dup motor (104mm/sec.) long 8-009, 010,011, 053, 054, 055, 056 008-021 3tm ta motor (52mm/sec.) start operation. Switches off...

  • Page 1202

    09/03 6-111 dc 3535/2240/1632, wc m24 dc330 general procedures and information initial issue 009-002 #m_disp mot m color disp. Mot turns on, and switches off automatically after 5sec. - 009-003 #c_disp mot c color disp. Mot turns on, and switches off automatically after 5sec. - 009-004 #k_disp mot k...

  • Page 1203

    09/03 6-112 dc 3535/2240/1632, wc m24 dc330 initial issue general procedures and information 012-011 rear tamper motor middle front on/off switches off automatically after 100pulses. 012-010, 012- 012, 012-013, 012-014, 012- 015 012-012 rear tamper motor high front on/off switches off automatically ...

  • Page 1204

    09/03 6-113 dc 3535/2240/1632, wc m24 dc330, dc351 general procedures and information initial issue dc351 nvm background processing purpose consists of 5 subroutines: • machine settings - this routine saves the current machine settings or restores the previ- ously-saved machine settings. • special b...

  • Page 1205

    09/03 6-114 dc 3535/2240/1632, wc m24 dc351, dc355 initial issue general procedures and information • chain 746 • chains 751 -753 • chain 760 • chain 762 • chain 764 • chain 769 b. If iit is selected machine settings in nvm chains 710 and 715 will be restored. C. If iot is selected, machine settings...

  • Page 1206

    09/03 6-115 dc 3535/2240/1632, wc m24 dc371, dc527 general procedures and information initial issue dc371 configuration page purpose allows easy viewing and set-up of machine configuration. Procedure 1. Enter the diagnostic mode. Refer to entering diagnostic mode using the pws . 2. Select adjustment...

  • Page 1207

    09/03 6-116 dc 3535/2240/1632, wc m24 dc612 initial issue general procedures and information dc612 color test pattern print purpose prints the test patterns in the machine, to help identify image quality problems. Procedure 1. Enter the diagnostic mode. Refer to entering diagnostic mode using the pw...

  • Page 1208

    09/03 6-117 dc 3535/2240/1632, wc m24 dc612 general procedures and information initial issue 13-0 binary highlight pg (highlight gradation check) gradation pattern for highlight adjustment lut: ctrax off; iot off in the gradation reproducibility of primary color/secondary color/ter- tiary color, the...

  • Page 1209

    09/03 6-118 dc 3535/2240/1632, wc m24 dc612 initial issue general procedures and information 35-0 multi-level_process control pg gradation pattern for density control lut: ctrax off; iot off the primary color/secondary color/tertiary color gradation reproduc- ibility can be checked by crossing over ...

  • Page 1210

    09/03 6-119 dc 3535/2240/1632, wc m24 dc685, dc921 general procedures and information initial issue dc685 color registration purpose note: for details on dc685 color registration, see adjustments section 4: adj 9.6 . Dc921 tc/atc sensor setup purpose note: for details on dc921 tc/atc sensor setup, s...

  • Page 1211

    09/03 6-120 dc 3535/2240/1632, wc m24 dc922, dc924 initial issue general procedures and information dc922 trc control purpose note: for details on dc922 trc control, see adjustments section 4: adj 9.3 dc922 trc control adjustment. Dc924 trc adjust purpose to manually fine adjust the low/medium/high ...

  • Page 1212

    09/03 6-121 dc 3535/2240/1632, wc m24 dc929, dc934 general procedures and information initial issue dc929 max setup purpose note: for the execution sequence of the max setup functions, see adjustments section 4: adj 9.1 . Dc934 adc/agc setup purpose automatically adjusts the adc sensor gain. Note: f...

  • Page 1213

    09/03 6-122 dc 3535/2240/1632, wc m24 dc945, dc956 initial issue general procedures and information dc945 iit calibration purpose functional details: • computes and sets the white reference correction coefficient. • corrects the iit sensitivity dispersion. Note: for details on dc945 iit calibration,...

  • Page 1214

    09/03 6-123 dc 3535/2240/1632, wc m24 gp 1 general procedures and information initial issue gp 1 network printing simulation purpose this procedure details a method of troubleshooting network printing problems. Caution this procedure was written based on pre-release data. The software installation p...

  • Page 1215

    09/03 6-124 dc 3535/2240/1632, wc m24 gp 2, gp 3 initial issue general procedures and information gp 2 machine startup troubleshooting purpose this procedure describes methods of recovering from failure of the machine to successfully complete the self-test/startup procedure. Description when power i...

  • Page 1216

    09/03 6-125 dc 3535/2240/1632, wc m24 gp 3, gp 4 general procedures and information initial issue to execute: simultaneously press and hold the 3, the stop, and the power save buttons on the control panel while switching on the power. Hold the buttons down until the boot up screen (5 circles) appear...

  • Page 1217

    09/03 6-126 dc 3535/2240/1632, wc m24 gp 4, gp 5 initial issue general procedures and information • wires chafing against components of the machine, especially against moving com- ponents • misaligned, misadjusted, or incorrectly installed components • slow or slipping clutches; slow or binding sole...

  • Page 1218

    09/03 6-127 dc 3535/2240/1632, wc m24 gp 5 general procedures and information initial issue 016 tonal signal output 1850hz 017 tonal signal output 2100hz 019 dtmf signal output dual tone 1 020 dtmf signal output dual tone 2 021 dtmf signal output dual tone 3 022 dtmf signal output dual tone 4 023 dt...

  • Page 1219

    09/03 6-128 dc 3535/2240/1632, wc m24 gp 5, gp 6 initial issue general procedures and information gp 6 resetting the administrator password purpose the purpose of this procedure is to allow the cse to recover the administrator password in sit- uations where the customer has changed the password from...

  • Page 1220

    09/03 6-129 dc 3535/2240/1632, wc m24 gp 10, gp 12 general procedures and information initial issue gp 10 replacing billing pwbs purpose this procedure is used to maintain serial number and billing data integrity when billing pwbs must be replaced. Procedure caution to maintain the integrity of the ...

  • Page 1221

    09/03 6-130 dc 3535/2240/1632, wc m24 gp 10, gp 12 initial issue general procedures and information.

  • Page 1222

    09/03 6-131 dc 3535/2240/1632, wc m24 space requirements general procedures and information initial issue space requirements installation space requirements are shown in figure 1 (dc 1632/2240 w/out finisher), figure 2 (dc 1632/2240 w/finisher), figure 3 , (dc 3535 w/out finisher), and figure 4 , (d...

  • Page 1223

    09/03 6-132 dc 3535/2240/1632, wc m24 space requirements initial issue general procedures and information figure 3 space requirement - wc 24, dc 3535 w/out finisher figure 4 space requirement - wc 24, dc 3535 w/finisher 50 mm 2 in. 254 mm 10 in. 1585 mm 62.4 in 508 mm 20 in. 2540 mm 100 in. (hallway...

  • Page 1224

    09/03 6-133 dc 3535/2240/1632, wc m24 product specs. General procedures and information initial issue product specs..

  • Page 1225

    09/03 6-134 dc 3535/2240/1632, wc m24 product specs. Initial issue general procedures and information product codes component weights paper capacities table 1 product codes dc 2240/1632 item product code docucolor 1632 iot 120 vac lve docucolor 1632 iot 220 vac lvf scanner/ui/dadf (xc) 120 vac lvm s...

  • Page 1226

    09/03 6-135 dc 3535/2240/1632, wc m24 product specs. General procedures and information initial issue copy speed workcentre m24 • b/w (plain paper; simplex; fed from tray 1) – letter size lef: 24 ppm – letter size sef: 20 ppm – legal size: 17 ppm – a3/11x17 in.: 15 ppm • color (plain paper; simplex;...

  • Page 1227

    09/03 6-136 dc 3535/2240/1632, wc m24 product specs. Initial issue general procedures and information • b/w - 4.6 sec. Max (dc 2240/1632); 8.2 sec (dc 3535) first print output time (does not include ess process time for prints); 8.5” x 11” (a4); tray 1; • color - 11.8 sec. Max (dc 2240/1632); 9.0 se...

  • Page 1228

    09/03 6-137 dc 3535/2240/1632, wc m24 common tools, product tools and test patterns general procedures and information initial issue common tools product tools and test patterns table 1 common tools description part number screw driver (-) 3 x 50 600t40205 screw driver (+) 6 x 100 600t1989 screw dri...

  • Page 1229

    09/03 6-138 dc 3535/2240/1632, wc m24 cleaning materials, glossary of terms initial issue general procedures and information cleaning materials machine consumables glossary of terms table 1 cleaning materials description nasg part number esg part number cleaning fluid (8oz., formula a) 43p48 8r90034...

  • Page 1230

    09/03 6-139 dc 3535/2240/1632, wc m24 glossary of terms general procedures and information initial issue mf multi-function mn multinational nic network interface card nvm non volatile memory oem original equipment manufacturer ogm on-going maintenance pc personal computer pl parts list po part of (a...

  • Page 1231

    09/03 6-140 dc 3535/2240/1632, wc m24 glossary of terms initial issue general procedures and information.

  • Page 1232

    09/03 6-141 dc 3535/2240/1632, wc m24 change tag introduction, dc 2240/1632 iot/pro- general procedures and information initial issue change tag introduction important modifications to the copier are identified by a tag number which is recorded on a tag matrix. The tag matrix for the iot (processor)...

  • Page 1233

    09/03 6-142 dc 3535/2240/1632, wc m24 dc 3535 iot/processor (p) tags, dc 3535 iot/pro- initial issue general procedures and information tag: p4 class: o use: all mfg serial numbers: lve: 186274 lvf:311 208685x name: v5.7 software maintenance release purpose: update ess rom to 2.41.5; mcu to 2.0.4 ki...

  • Page 1234

    09/03 6-143 dc 3535/2240/1632, wc m24 wc m24 iot/processor (p) tags, dc 2240/1632 iit/ general procedures and information initial issue wc m24 iot/processor (p) tags there are no tags assigned to this product dc 2240/1632 iit/document handler (d) tags the following iit change tags have been issued: ...

  • Page 1235

    09/03 6-144 dc 3535/2240/1632, wc m24 dc 3535 iit/document handler (d) tags, wc m24 iit/ initial issue general procedures and information dc 3535 iit/document handler (d) tags tag: d1 class: o use: all mfg serial numbers: mwd: 279863 mwe: 311 294689x name: software release purpose: update iiss s/w t...

  • Page 1236

    09/03 6-145 dc 3535/2240/1632, wc m24 wc m24 iit/document handler (d) tags general procedures and information initial issue wc m24 iit/document handler (d) tags there are no tags assigned to this product.

  • Page 1237

    09/03 6-146 dc 3535/2240/1632, wc m24 wc m24 iit/document handler (d) tags initial issue general procedures and information.

  • Page 1238: 7 Wiring Data

    09/03 7-1 dc 3535/2240/1632, wc m24 wiring data initial issue 7 wiring data plug/jack locations plug/jack locations ........................................................................................................ 7-3 wirenets ac wirenets .........................................................

  • Page 1239

    09/03 7-2 dc 3535/2240/1632, wc m24 initial issue wiring data.

  • Page 1240

    09/03 7-3 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue plug/jack locations how to use the plug/jack location list the plug/jack location list below is provided to locate plugs, jacks, or other terminating devices. Locate the desired termination device in the first column (...

  • Page 1241

    09/03 7-4 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data p/j235 figure 17 2 developer motor, tray 1 size switch p/j237 figure 11 3 ibt belt assembly p/j240 figure 5 2 registration transport assembly p/j251 figure 3 6 inverter transport assembly p/j255 figure 2 4 mob sensor a...

  • Page 1242

    09/03 7-5 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue p/j549 figure 25 13 tt module (rear) p/j549 figure 26 8 3t module (rear) p/j550 figure 16 3 i/f pwb, main motor, lvps p/j550 figure 29 5 dadf (2 of 2) p/j551 figure 16 25 i/f pwb, main motor, lvps p/j551 figure 29 4 da...

  • Page 1243

    09/03 7-6 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data p/j646 figure 17 8 developer motor, tray 1 size switch p/j668 figure 12 15 hvps, +24v lvps p/j669 figure 12 16 hvps, +24v lvps p/j670 figure 20 9 tt module (tray 2,3 feeder) p/j670 figure 21 12 3t module (tray 2,3,4 fe...

  • Page 1244

    09/03 7-7 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue p/j842 figure 21 9 3t module (tray 2,3,4 feeder) p/j843 figure 35 9 finisher pwb p/j844 figure 35 8 finisher pwb p/j845 figure 35 5 finisher pwb p/j846 figure 35 6 finisher pwb p/j847 figure 35 7 finisher pwb p/j848 fi...

  • Page 1245

    09/03 7-8 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data fs41 figure 18 4 ac drive pwb, noise filter pwb, delay pwb fs45 figure 18 9 ac drive pwb, noise filter pwb, delay pwb fs47 figure 18 7 ac drive pwb, noise filter pwb, delay pwb fs48 figure 18 8 ac drive pwb, noise filt...

  • Page 1246

    09/03 7-9 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue plug/jack illustrations figure 1 xerographics.

  • Page 1247

    09/03 7-10 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 2 mob sensor assembly.

  • Page 1248

    09/03 7-11 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 3 inverter transport assembly.

  • Page 1249

    09/03 7-12 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 4 duplex transport assembly.

  • Page 1250

    09/03 7-13 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 5 registration transport assembly.

  • Page 1251

    09/03 7-14 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 6 fuser assembly.

  • Page 1252

    09/03 7-15 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 7 exit transport assembly (oct).

  • Page 1253

    09/03 7-16 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 8 tray 5.

  • Page 1254

    09/03 7-17 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 9 toner dispense motor (y,m,c,k), main switch.

  • Page 1255

    09/03 7-18 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 10 ros assembly.

  • Page 1256

    09/03 7-19 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 11 ibt belt assembly.

  • Page 1257

    09/03 7-20 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 12 hvps, +24v lvps.

  • Page 1258

    09/03 7-21 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 13 outlet panel assembly, fuser pwb.

  • Page 1259

    09/03 7-22 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 14 ess assembly.

  • Page 1260

    09/03 7-23 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 15 mcu pwb.

  • Page 1261

    09/03 7-24 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 16 i/f pwb, main motor, lvps.

  • Page 1262

    09/03 7-25 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 17 developer motor, tray 1 size switch.

  • Page 1263

    09/03 7-26 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 18 ac drive pwb, noise filter pwb, delay pwb.

  • Page 1264

    09/03 7-27 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 19 left lower assembly, tray 1 feeder.

  • Page 1265

    09/03 7-28 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 20 tt module (tray 2, 3 feeder) tandem tray module.

  • Page 1266

    09/03 7-29 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 21 3t module (tray 2, 3,4 feeder) 3 tray module.

  • Page 1267

    09/03 7-30 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 22 tt module (tray 4 feeder) tandem tray module.

  • Page 1268

    09/03 7-31 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 23 tt module (tray 2,3,4 paper size switches) tandem tray module.

  • Page 1269

    09/03 7-32 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 24 3t module (tray 2,3,4 paper size switches) 3 tray module.

  • Page 1270

    09/03 7-33 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 25 tt module (rear) tandem tray module (rear).

  • Page 1271

    09/03 7-34 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 26 3t module (rear) 3 tray module (rear).

  • Page 1272

    09/03 7-35 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 27 control panel.

  • Page 1273

    09/03 7-36 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 28 dadf (1 of 2).

  • Page 1274

    09/03 7-37 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 29 dadf (2 of 2).

  • Page 1275

    09/03 7-38 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 30 iit (front).

  • Page 1276

    09/03 7-39 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 31 iit (rear).

  • Page 1277

    09/03 7-40 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 32 h - transport assembly.

  • Page 1278

    09/03 7-41 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 33 tamper unit, staple unit.

  • Page 1279

    09/03 7-42 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 34 finisher (rear).

  • Page 1280

    09/03 7-43 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 35 finisher pwb.

  • Page 1281

    09/03 7-44 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data figure 36 vsel assembly.

  • Page 1282

    09/03 7-45 dc 3535/2240/1632, wc m24 plug/jack locations wiring data initial issue figure 37 fax module.

  • Page 1283

    09/03 7-46 dc 3535/2240/1632, wc m24 plug/jack locations initial issue wiring data.

  • Page 1284

    09/03 7-47 dc 3535/2240/1632, wc m24 ac wirenets wiring data initial issue ac wirenets figure 1 ach wirenet.

  • Page 1285

    09/03 7-48 dc 3535/2240/1632, wc m24 ac wirenets initial issue wiring data figure 2 acn wirenet.

  • Page 1286

    09/03 7-49 dc 3535/2240/1632, wc m24 +3.3 vdc / +3.3vdc rtn wirenets wiring data initial issue +3.3 vdc / +3.3vdc rtn wirenets figure 1 +3.3vdc wirenet (1 of 2 -dc 2240/1632).

  • Page 1287

    09/03 7-50 dc 3535/2240/1632, wc m24 +3.3 vdc / +3.3vdc rtn wirenets initial issue wiring data figure 2 +3.3vdc wirenet (2 of 2 -dc 3535).

  • Page 1288

    09/03 7-51 dc 3535/2240/1632, wc m24 +3.3 vdc / +3.3vdc rtn wirenets wiring data initial issue figure 3 3.3v rtn wirenet (1 of 2 -dc 2240/1632).

  • Page 1289

    09/03 7-52 dc 3535/2240/1632, wc m24 +3.3 vdc / +3.3vdc rtn wirenets initial issue wiring data figure 4 +3.3v rtn wirenet (2 of 2 -dc 3535).

  • Page 1290

    09/03 7-53 dc 3535/2240/1632, wc m24 +5 vdc wirenets wiring data initial issue +5 vdc wirenets figure 1 +5 vdc wirenet (1 of 6).

  • Page 1291

    09/03 7-54 dc 3535/2240/1632, wc m24 +5 vdc wirenets initial issue wiring data figure 2 +5 vdc wirenet (2 of 6 - dc 2240/1632).

  • Page 1292

    09/03 7-55 dc 3535/2240/1632, wc m24 +5 vdc wirenets wiring data initial issue figure 3 +5 vdc wirenet (3 of 6 - dc 2240/1632).

  • Page 1293

    09/03 7-56 dc 3535/2240/1632, wc m24 +5 vdc wirenets initial issue wiring data figure 4 +5 vdc wirenet (4 of 6).

  • Page 1294

    09/03 7-57 dc 3535/2240/1632, wc m24 +5 vdc wirenets wiring data initial issue figure 5 +5vdc wirenet (5 of 6 - dc3535).

  • Page 1295

    09/03 7-58 dc 3535/2240/1632, wc m24 +5 vdc wirenets initial issue wiring data figure 6 +5vdc wirenet (6 of 6 - dc3535).

  • Page 1296

    09/03 7-59 dc 3535/2240/1632, wc m24 +5 vdc rtn wirenets wiring data initial issue +5 vdc rtn wirenets figure 1 5v rtn (1 of 4) wirenet.

  • Page 1297

    09/03 7-60 dc 3535/2240/1632, wc m24 +5 vdc rtn wirenets initial issue wiring data figure 2 5v rtn (2 of 4) wirenet.

  • Page 1298

    09/03 7-61 dc 3535/2240/1632, wc m24 +5 vdc rtn wirenets wiring data initial issue figure 3 5v rtn (3 of 4) wirenet.

  • Page 1299

    09/03 7-62 dc 3535/2240/1632, wc m24 +5 vdc rtn wirenets initial issue wiring data figure 4 5v rtn (4 of 4) wirenet.

  • Page 1300

    09/03 7-63 dc 3535/2240/1632, wc m24 +24 vdc wirenets wiring data initial issue +24 vdc wirenets figure 1 +24vdc (1 of 5) wirenet.

  • Page 1301

    09/03 7-64 dc 3535/2240/1632, wc m24 +24 vdc wirenets initial issue wiring data figure 2 +24vdc (2 of 5) wirenet.

  • Page 1302

    09/03 7-65 dc 3535/2240/1632, wc m24 +24 vdc wirenets wiring data initial issue figure 3 +24vdc (3 of 5) wirenet.

  • Page 1303

    09/03 7-66 dc 3535/2240/1632, wc m24 +24 vdc wirenets initial issue wiring data figure 4 +24vdc (4 of 5) wirenet.

  • Page 1304

    09/03 7-67 dc 3535/2240/1632, wc m24 +24 vdc wirenets wiring data initial issue figure 5 +24vdc (5 of 5) wirenet.

  • Page 1305

    09/03 7-68 dc 3535/2240/1632, wc m24 +24 vdc rtn wirenets initial issue wiring data +24 vdc rtn wirenets figure 1 24v rtn (1 of 2) wirenet.

  • Page 1306

    09/03 7-69 dc 3535/2240/1632, wc m24 +24 vdc rtn wirenets wiring data initial issue figure 2 24v rtn (2 of 2) wirenet.

  • Page 1307

    09/03 7-70 dc 3535/2240/1632, wc m24 iit wirenets initial issue wiring data iit wirenets figure 1 iit +3.3vdc & 3.3v rtn wirenets.

  • Page 1308

    09/03 7-71 dc 3535/2240/1632, wc m24 iit wirenets wiring data initial issue figure 2 iit +5vdc & 5v rtn wirenets.

  • Page 1309

    09/03 7-72 dc 3535/2240/1632, wc m24 iit wirenets initial issue wiring data figure 3 iit +24vdc wirenet.

  • Page 1310

    09/03 7-73 dc 3535/2240/1632, wc m24 iit wirenets wiring data initial issue figure 4 iit 24v rtn.

  • Page 1311

    09/03 7-74 dc 3535/2240/1632, wc m24 dadf wirenets initial issue wiring data dadf wirenets figure 1 dadf +5vdc wirenet.

  • Page 1312

    09/03 7-75 dc 3535/2240/1632, wc m24 dadf wirenets wiring data initial issue figure 2 dadf 5v rtn.

  • Page 1313

    09/03 7-76 dc 3535/2240/1632, wc m24 dadf wirenets initial issue wiring data figure 3 dadf +24vdc wirenet.

  • Page 1314

    09/03 7-77 dc 3535/2240/1632, wc m24 finisher wirenets wiring data initial issue finisher wirenets figure 1 finisher +5vdc (1 of 2) wirenet.

  • Page 1315

    09/03 7-78 dc 3535/2240/1632, wc m24 finisher wirenets initial issue wiring data figure 2 +5vdc (2 of 2) wirenet.

  • Page 1316

    09/03 7-79 dc 3535/2240/1632, wc m24 finisher wirenets wiring data initial issue figure 3 5v rtn (1 of 2) wirenet.

  • Page 1317

    09/03 7-80 dc 3535/2240/1632, wc m24 finisher wirenets initial issue wiring data figure 4 5v rtn (2 of 2) wirenet.

  • Page 1318

    09/03 7-81 dc 3535/2240/1632, wc m24 finisher wirenets wiring data initial issue figure 5 finisher +24vdc wirenet.

  • Page 1319

    09/03 7-82 dc 3535/2240/1632, wc m24 finisher wirenets initial issue wiring data figure 6 finisher 24v rtn wirenet.

  • Page 1320

    09/03 7-83 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue chain 01 main power figure 1 bsd 1.1a main power on (1 of 2).

  • Page 1321

    09/03 7-84 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 2 bsd 1.1b main power on (2 of 2).

  • Page 1322

    09/03 7-85 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 3 bsd 1.2 lvps control (dc 2240/1632, wc 24).

  • Page 1323

    09/03 7-86 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 4 bsd 1.2 lvps control (dc 3535).

  • Page 1324

    09/03 7-87 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 5 bsd 1.3 dc power generation - +3.3vdc (dc 2240/1632, wc 24).

  • Page 1325

    09/03 7-88 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 6 bsd 1.3 dc power generation - +3.3vdc (dc 3535).

  • Page 1326

    09/03 7-89 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 7 bsd 1.4 dc power generation - +5 vdc (dc 2240/1632, wc 24).

  • Page 1327

    09/03 7-90 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 8 bsd 1.4 dc power generation - +5 vdc (dc 3535).

  • Page 1328

    09/03 7-91 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 9 bsd 1.5 dc power generation - +24vdc (dc 2240/1632, wc 24).

  • Page 1329

    09/03 7-92 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 10 bsd 1.5 dc power generation - +24vdc (dc 3535).

  • Page 1330

    09/03 7-93 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 11 bsd 1.6 dc power generation (iit lvps).

  • Page 1331

    09/03 7-94 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 12 bsd 1.7 power interlock switching (dc 2240/1632).

  • Page 1332

    09/03 7-95 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 13 bsd 1.7 power interlock switching (dc 3535).

  • Page 1333

    09/03 7-96 dc 3535/2240/1632, wc m24 chain 01 main power initial issue wiring data figure 14 bsd 1.8 tray module power interlock switching.

  • Page 1334

    09/03 7-97 dc 3535/2240/1632, wc m24 chain 01 main power wiring data initial issue figure 15 bsd 1.9 monitoring.

  • Page 1335

    09/03 7-98 dc 3535/2240/1632, wc m24 chain 02 mode selection initial issue wiring data chain 02 mode selection figure 1 bsd 2.1 control panel.

  • Page 1336

    09/03 7-99 dc 3535/2240/1632, wc m24 chain 02 mode selection wiring data initial issue figure 2 bsd 2.2 lcd control.

  • Page 1337

    09/03 7-100 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data chain 03 printer communication figure 1 bsd 3.1 pwb communication (1 of 7 - dc 2240/1632, wc 24).

  • Page 1338

    09/03 7-101 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 2 bsd 3.1 pwb communication (2 of 7 - dc 3535).

  • Page 1339

    09/03 7-102 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 3 bsd 3.1 pwb communication (3 of 7).

  • Page 1340

    09/03 7-103 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 4 bsd 3.1 pwb communication (4 of 7).

  • Page 1341

    09/03 7-104 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 5 bsd 3.1 pwb communication (5 of 7 - dc2240/1632, wc 24).

  • Page 1342

    09/03 7-105 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 6 bsd 3.1 pwb communication (6 of 7 - dc3535).

  • Page 1343

    09/03 7-106 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 7 bsd 3.1 pwb communication (7 of 7 - wc 24 w/fax only).

  • Page 1344

    09/03 7-107 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 8 bsd 3.2 option device detection.

  • Page 1345

    09/03 7-108 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 9 bsd 3.3 foreign interface.

  • Page 1346

    09/03 7-109 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 10 bsd 3.42 pws interface.

  • Page 1347

    09/03 7-110 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 11 bsd 3.5 electric billing.

  • Page 1348

    09/03 7-111 dc 3535/2240/1632, wc m24 chain 03 printer communication wiring data initial issue figure 12 bsd 3.6a monitoring (1 of 2).

  • Page 1349

    09/03 7-112 dc 3535/2240/1632, wc m24 chain 03 printer communication initial issue wiring data figure 13 bsd 3.6 monitoring (2 of 2).

  • Page 1350

    09/03 7-113 dc 3535/2240/1632, wc m24 chain 04 print power wiring data initial issue figure 1 bsd 4.1a main drive control (1 of 2).

  • Page 1351

    09/03 7-114 dc 3535/2240/1632, wc m24 chain 04 print power initial issue wiring data figure 2 bsd 4.1b main drive control (2 of 2).

  • Page 1352

    09/03 7-115 dc 3535/2240/1632, wc m24 chain 05 document handler wiring data initial issue chain 05 document handler figure 1 bsd 5.1 dadf dc power and interlocks.

  • Page 1353

    09/03 7-116 dc 3535/2240/1632, wc m24 chain 05 document handler initial issue wiring data figure 2 bsd 5.2 pwbs communications.

  • Page 1354

    09/03 7-117 dc 3535/2240/1632, wc m24 chain 05 document handler wiring data initial issue figure 3 bsd 5.3 document setting and feeding.

  • Page 1355

    09/03 7-118 dc 3535/2240/1632, wc m24 chain 05 document handler initial issue wiring data figure 4 bsd 5.4 document transportation.

  • Page 1356

    09/03 7-119 dc 3535/2240/1632, wc m24 chain 05 document handler wiring data initial issue figure 5 bsd 5.5 document transport.

  • Page 1357

    09/03 7-120 dc 3535/2240/1632, wc m24 chain 05 document handler initial issue wiring data figure 6 bsd 5.6 document exit transportation.

  • Page 1358

    09/03 7-121 dc 3535/2240/1632, wc m24 chain 05 document handler wiring data initial issue figure 7 bsd 5.7 dadf monitoring.

  • Page 1359

    09/03 7-122 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data chain 06 imaging figure 1 bsd 6.1 document illumination.

  • Page 1360

    09/03 7-123 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 2 bsd 6.2 image input.

  • Page 1361

    09/03 7-124 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 3 bsd 6.3 platen document setting.

  • Page 1362

    09/03 7-125 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 4 bsd 6.4 carriage control.

  • Page 1363

    09/03 7-126 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 5 bsd 6.5 (1 of 3) laser and scanning control - yellow (dc 2240/1632, wc 24).

  • Page 1364

    09/03 7-127 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 6 bsd 6.5 (2 of 3) laser and scanning control - yellow (dc 3535).

  • Page 1365

    09/03 7-128 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 7 bsd 6.5 (3 of 3) laser and scanning control - yellow.

  • Page 1366

    09/03 7-129 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 8 bsd 6.6 (1 of 3) laser and scanning control - magenta (dc 2240/1632, wc 24).

  • Page 1367

    09/03 7-130 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 9 bsd 6.6 (2 of 3) laser and scanning control - magenta (dc 3535).

  • Page 1368

    09/03 7-131 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 10 bsd 6.6 (3 of 3) laser and scanning control - magenta.

  • Page 1369

    09/03 7-132 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 11 bsd 6.7 (1 of 3) laser and scanning control - cyan (dc 2240/1632, wc 24).

  • Page 1370

    09/03 7-133 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 12 bsd 6.7 (2 of 3) laser and scanning control - cyan (dc 3535).

  • Page 1371

    09/03 7-134 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 13 bsd 6.7 (3 of 3) laser and scanning control - cyan.

  • Page 1372

    09/03 7-135 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 14 bsd 6.8 (1 of 3) laser and scanning control - black (dc 2240/1632, wc 24).

  • Page 1373

    09/03 7-136 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 15 bsd 6.8 (2 of 3) laser and scanning control - black (dc 3535).

  • Page 1374

    09/03 7-137 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 16 bsd 6.8 (3 of 3) laser and scanning control - black.

  • Page 1375

    09/03 7-138 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 17 bsd 6.9 laser scan drive control.

  • Page 1376

    09/03 7-139 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 18 bsd 6.10 ros shutter control.

  • Page 1377

    09/03 7-140 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 19 6.11 color registration control.

  • Page 1378

    09/03 7-141 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 20 bsd 6.12a image monitoring (1 of 3).

  • Page 1379

    09/03 7-142 dc 3535/2240/1632, wc m24 chain 06 imaging initial issue wiring data figure 21 bsd 6.12b image monitoring (2 of 3).

  • Page 1380

    09/03 7-143 dc 3535/2240/1632, wc m24 chain 06 imaging wiring data initial issue figure 22 bsd 6.12c image monitoring (3 of 3).

  • Page 1381

    09/03 7-144 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data chain 07 paper supply figure 1 bsd 7.1 tray 1 paper size sensing.

  • Page 1382

    09/03 7-145 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 2 bsd 7.2 tray 2 paper size sensing ttm.

  • Page 1383

    09/03 7-146 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 3 bsd 7.2 tray 2 paper size sensing 3tm.

  • Page 1384

    09/03 7-147 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 4 bsd 7.3 tray 3 paper size sensing ttm.

  • Page 1385

    09/03 7-148 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 5 bsd 7.3 tray 3 paper size sensing 3tm.

  • Page 1386

    09/03 7-149 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 6 bsd 7.4 tray 4 paper size sensing ttm.

  • Page 1387

    09/03 7-150 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 7 bsd 7.4 tray 4 paper size sensing 3tm.

  • Page 1388

    09/03 7-151 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 8 bsd 7.5 tray 1 paper stacking.

  • Page 1389

    09/03 7-152 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 9 bsd 7.6 tray 2 paper stacking ttm.

  • Page 1390

    09/03 7-153 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 10 bsd 7.6 tray 2 paper stacking 3tm.

  • Page 1391

    09/03 7-154 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 11 bsd 7.7 tray 3 paper stacking ttm.

  • Page 1392

    09/03 7-155 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 12 bsd 7.7 tray 3 paper stacking 3tm.

  • Page 1393

    09/03 7-156 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 13 bsd 7.8 tray 4 paper stacking ttm.

  • Page 1394

    09/03 7-157 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 14 bsd 7.8 tray 4 paper stacking 3tm.

  • Page 1395

    09/03 7-158 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 15 bsd 7.9 tray 5 paper stacking (dc 2240/1632, wc 24).

  • Page 1396

    09/03 7-159 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 16 bsd 7.9 tray 5 paper stacking (dc 3535).

  • Page 1397

    09/03 7-160 dc 3535/2240/1632, wc m24 chain 07 paper supply initial issue wiring data figure 17 bsd 7.10a paper feed monitoring (1 of 2).

  • Page 1398

    09/03 7-161 dc 3535/2240/1632, wc m24 chain 07 paper supply wiring data initial issue figure 18 bsd 7.10b paper feed monitoring (2 of 2).

  • Page 1399

    09/03 7-162 dc 3535/2240/1632, wc m24 chain 08 paper registration initial issue wiring data chain 08 paper registration figure 1 bsd 8.1 tray 1 - 5 paper feeding.

  • Page 1400

    09/03 7-163 dc 3535/2240/1632, wc m24 chain 08 paper registration wiring data initial issue figure 2 bsd 8.2 iot paper transportation.

  • Page 1401

    09/03 7-164 dc 3535/2240/1632, wc m24 chain 08 paper registration initial issue wiring data figure 3 bsd 8.3 tray module paper transportation ttm.

  • Page 1402

    09/03 7-165 dc 3535/2240/1632, wc m24 chain 08 paper registration wiring data initial issue figure 4 bsd 8.3 tray module paper transportation 3tm.

  • Page 1403

    09/03 7-166 dc 3535/2240/1632, wc m24 chain 08 paper registration initial issue wiring data figure 5 bsd 8.4 tray module paper transportation drive control ttm.

  • Page 1404

    09/03 7-167 dc 3535/2240/1632, wc m24 chain 08 paper registration wiring data initial issue figure 6 bsd 8.4 tray module paper transportation drive control 3tm.

  • Page 1405

    09/03 7-168 dc 3535/2240/1632, wc m24 chain 08 paper registration initial issue wiring data figure 7 bsd 8.5 registration.

  • Page 1406

    09/03 7-169 dc 3535/2240/1632, wc m24 chain 08 paper registration wiring data initial issue figure 8 bsd 8.6 monitoring.

  • Page 1407

    09/03 7-170 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data chain 09 xerographics figure 1 bsd 9.1 drum drive control (y, m, c) (dc 2240/1632, wc 24).

  • Page 1408

    09/03 7-171 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 2 bsd 9.1 drum drive control (y,m,c) (dc 3535).

  • Page 1409

    09/03 7-172 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 3 bsd 9.2 drum drive control (k) (dc 2240/1632, wc 24).

  • Page 1410

    09/03 7-173 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 4 bsd 9.2 drum drive control (k) (dc 3535).

  • Page 1411

    09/03 7-174 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 5 bsd 9.3 drum life control (y,m).

  • Page 1412

    09/03 7-175 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 6 bsd 9.4 drum life control (c,k).

  • Page 1413

    09/03 7-176 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 7 bsd 9.5 charging and exposure (y).

  • Page 1414

    09/03 7-177 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 8 bsd 9.6 charging and exposure (m).

  • Page 1415

    09/03 7-178 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 9 bsd 9.7 charging and exposure (c).

  • Page 1416

    09/03 7-179 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 10 bsd 9.8 charging and exposure (k).

  • Page 1417

    09/03 7-180 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 11 bsd 9.9 developer drive control (dc 2240/1632, wc 24).

  • Page 1418

    09/03 7-181 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 12 bsd 9.9 developer drive control (dc 3535).

  • Page 1419

    09/03 7-182 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 13 bsd 9.10 development (y).

  • Page 1420

    09/03 7-183 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 14 bsd 9.11 development (m).

  • Page 1421

    09/03 7-184 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 15 9.12 development (c).

  • Page 1422

    09/03 7-185 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 16 bsd 9.13a development (k) (1 of 2).

  • Page 1423

    09/03 7-186 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 17 bsd 9.13b development (k) (2 of 2).

  • Page 1424

    09/03 7-187 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 18 bsd 9.14 new toner cartridge detection.

  • Page 1425

    09/03 7-188 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 19 bsd 9.15 toner dispense control.

  • Page 1426

    09/03 7-189 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 20 bsd 9.16 adc and environment sensing (dc 2240/1632, wc 24).

  • Page 1427

    09/03 7-190 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 21 bsd 9.16 adc and environment sensing (dc 3535).

  • Page 1428

    09/03 7-191 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 22 bsd 9.17 ibt drive control.

  • Page 1429

    09/03 7-192 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 23 bsd 9.18 1st btr contact retract control.

  • Page 1430

    09/03 7-193 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 24 bsd 9.19 ibt positioning.

  • Page 1431

    09/03 7-194 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 25 bsd 9.20 image transfer to ibt (y).

  • Page 1432

    09/03 7-195 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 26 bsd 9.21 image transfer to ibt (m).

  • Page 1433

    09/03 7-196 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 27 bsd 9.22 image transfer to ibt (c).

  • Page 1434

    09/03 7-197 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 28 bsd 9.23 image transfer to ibt (k).

  • Page 1435

    09/03 7-198 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 29 bsd 9.24a image transfer to paper (1 of 2).

  • Page 1436

    09/03 7-199 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 30 bsd 9.24b image transfer to paper (2 of 2).

  • Page 1437

    09/03 7-200 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 31 bsd 9.25 stripping.

  • Page 1438

    09/03 7-201 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 32 bsd 9.26 drum cleaning (y,m).

  • Page 1439

    09/03 7-202 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 33 bsd 9.27 drum cleaning (c,k).

  • Page 1440

    09/03 7-203 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 34 bsd 9.28 ibt cleaning.

  • Page 1441

    09/03 7-204 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 35 bsd 9.29 waste toner disposal.

  • Page 1442

    09/03 7-205 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 36 bsd 9.30 rear fan control (dc 2240/1632, wc 24).

  • Page 1443

    09/03 7-206 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 37 bsd 9.30 rear fan control (dc 3535).

  • Page 1444

    09/03 7-207 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 38 bsd 9.31a monitoring (1 of 5).

  • Page 1445

    09/03 7-208 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 39 bsd 9.31b monitoring (2 of 5).

  • Page 1446

    09/03 7-209 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 40 bsd 9.31c monitoring (3 of 5).

  • Page 1447

    09/03 7-210 dc 3535/2240/1632, wc m24 chain 09 xerographics initial issue wiring data figure 41 bsd 9.31d monitoring (4 of 5).

  • Page 1448

    09/03 7-211 dc 3535/2240/1632, wc m24 chain 09 xerographics wiring data initial issue figure 42 bsd 9.31e monitoring (5 of 5).

  • Page 1449

    09/03 7-212 dc 3535/2240/1632, wc m24 chain 10 fusing and output initial issue wiring data chain 10 fusing and output figure 1 bsd 10.1 fusing heat control (1 of 2).

  • Page 1450

    09/03 7-213 dc 3535/2240/1632, wc m24 chain 10 fusing and output wiring data initial issue figure 2 bsd 10.1 fusing heat control (2 of 2).

  • Page 1451

    09/03 7-214 dc 3535/2240/1632, wc m24 chain 10 fusing and output initial issue wiring data figure 3 bsd 10.2 fusing.

  • Page 1452

    09/03 7-215 dc 3535/2240/1632, wc m24 chain 10 fusing and output wiring data initial issue figure 4 bsd 10.3a inverter (1 of 2).

  • Page 1453

    09/03 7-216 dc 3535/2240/1632, wc m24 chain 10 fusing and output initial issue wiring data figure 5 bsd 10.3b inverter (2 of 2).

  • Page 1454

    09/03 7-217 dc 3535/2240/1632, wc m24 chain 10 fusing and output wiring data initial issue figure 6 bsd 10.4 duplex drive control.

  • Page 1455

    09/03 7-218 dc 3535/2240/1632, wc m24 chain 10 fusing and output initial issue wiring data figure 7 bsd 10.5 duplex drive.

  • Page 1456

    09/03 7-219 dc 3535/2240/1632, wc m24 chain 10 fusing and output wiring data initial issue figure 8 bsd 10.6 offset drive.

  • Page 1457

    09/03 7-220 dc 3535/2240/1632, wc m24 chain 10 fusing and output initial issue wiring data figure 9 bsd 10.7 monitoring.

  • Page 1458

    09/03 7-221 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue chain 12 finisher figure 1 bsd 12.1 dc power and interlocks.

  • Page 1459

    09/03 7-222 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 2 bsd 12.2 pwb communications.

  • Page 1460

    09/03 7-223 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 3 bsd 12.3 copy and drive delivery.

  • Page 1461

    09/03 7-224 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 4 bsd 12.4 horizontal transportation.

  • Page 1462

    09/03 7-225 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 5 bsd 12.5 decurler and paper transportation.

  • Page 1463

    09/03 7-226 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 6 bsd 12.6 tamping and offset.

  • Page 1464

    09/03 7-227 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 7 bsd 12.7 staple positioning.

  • Page 1465

    09/03 7-228 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 8 bsd 12.8 staple control.

  • Page 1466

    09/03 7-229 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 9 bsd 12.9 set eject.

  • Page 1467

    09/03 7-230 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 10 bsd 12.10a stacker tray control (1 of 2).

  • Page 1468

    09/03 7-231 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 11 bsd 12.10b stacker tray control (2 of 2).

  • Page 1469

    09/03 7-232 dc 3535/2240/1632, wc m24 chain 12 finisher initial issue wiring data figure 12 bsd 12.11a monitoring (1 of 2).

  • Page 1470

    09/03 7-233 dc 3535/2240/1632, wc m24 chain 12 finisher wiring data initial issue figure 13 bsd 12.11 monitoring (2 of 2).

  • Page 1471

    09/03 7-234 dc 3535/2240/1632, wc m24 chain 16 ess initial issue wiring data chain 16 ess figure 1 bsd 16.1 ess pwb.

  • Page 1472

    09/03 7-235 dc 3535/2240/1632, wc m24 chain 16 ess wiring data initial issue figure 2 bsd 13.2a ess monitoring (1 of 3).

  • Page 1473

    09/03 7-236 dc 3535/2240/1632, wc m24 chain 16 ess initial issue wiring data figure 3 bsd 13.2b ess monitoring (2 of 3).

  • Page 1474

    09/03 7-237 dc 3535/2240/1632, wc m24 chain 16 ess wiring data initial issue figure 4 bsd 13.2c ess monitoring (3 of 3).

  • Page 1475

    09/03 7-238 dc 3535/2240/1632, wc m24 chain 17 fax initial issue wiring data chain 17 fax figure 1 bsd 17.1 fax.

  • Page 1476: 9 Installation

    09/03 9-1 dc 3535/2240/1632, wc m24 installation initial issue 9 installation installation / completion checklist (nasg)..................................................................... 9-3 token ring installation (dc2240/1632 only) ..................................................................

  • Page 1477

    09/03 9-2 dc 3535/2240/1632, wc m24 initial issue installation.

  • Page 1478

    09/03 9-3 dc 3535/2240/1632, wc m24 installation / completion checklist (nasg) installation initial issue installation / completion checklist (nasg) checklist 1. Ensure that all packing material is removed and input / output accessories and options are properly installed. 2. Check space and power. 3...

  • Page 1479

    09/03 9-4 dc 3535/2240/1632, wc m24 token ring installation initial issue installation token ring installation (dc2240/1632 only) purpose the purpose of this kit is to enable the machine to use the token ring network. Caution use esd protection during the installation. Kit contents check kit content...

  • Page 1480

    09/03 9-5 dc 3535/2240/1632, wc m24 token ring installation installation initial issue 10. Place the new chassis assembly riser over the ess pwb and align the holes in the chassis with the screw holes in the ess pwb. Align the connector on the bottom of the assembly with the matching connector on th...

  • Page 1481

    09/03 9-6 dc 3535/2240/1632, wc m24 token ring installation initial issue installation figure 5 token ring pwb 23. The led indicates a successful network connection. If the led is off, call for network assistance. Green led.

  • Page 1482

    09/03 9-7 dc 3535/2240/1632, wc m24 foreign interface installation installation initial issue foreign interface installation purpose the purpose of this kit is install a plug and play foreign interface accessory that will enable the customer to attach a third-party vending device such as a debit mac...

  • Page 1483

    09/03 9-8 dc 3535/2240/1632, wc m24 fax kit installation initial issue installation fax kit installation purpose the purpose of this kit is install a fax module on workcentre 24 machines. Kit contents check the kit contents against the following list: figure 1 kit contents procedure installing the r...

  • Page 1484

    09/03 9-9 dc 3535/2240/1632, wc m24 fax kit installation installation initial issue figure 4 installing guide bracket and plate 11. Insert the fax i/f pwb into the lower slot, ensuring the connectors mate correctly. 12. Tighten the thumbscrews on the front of the pwb. 13. Reinstall the ess top cover...

  • Page 1485

    09/03 9-10 dc 3535/2240/1632, wc m24 fax kit installation initial issue installation figure 8 preparing tray module cover 6. Reinstall the tray module rear cover. Installing the one-touch panel 1. Remove the control panel ( figure 9 ). Figure 9 removing the control panel 2. Remove the left panel. Re...

  • Page 1486

    09/03 9-11 dc 3535/2240/1632, wc m24 fax kit installation installation initial issue figure 12 installing fax cables 2. Reconnect the iit and iot ( figure 13 ). Figure 13 iot/iit interconnection 3. Switch on the power. 4. Enter dc131 in ui diagnostic mode , and ensure that nvm loc. [700-165] is set ...

  • Page 1487

    09/03 9-12 dc 3535/2240/1632, wc m24 fax kit installation initial issue installation g3 option kit installation 1. Switch off the machine and disconnect the power cord. 2. Remove the rear cover (tray module) ( rep 14.9 ). 3. Remove the fax module cover ( figure 14 ). Figure 14 removing the fax modul...

  • Page 1488

    09/03 9-13 dc 3535/2240/1632, wc m24 fax kit installation installation initial issue figure 16 installing the g3 pwb (optional line) 6. Reinstall the fax module cover and the rear cover (tray module). Align the g3 pwb connec- tor and add port pwb con- nector and slide the g3 pwb in place.

  • Page 1489

    09/03 9-14 dc 3535/2240/1632, wc m24 fax kit installation initial issue installation.