Xray T1R Racer Instruction Manual - page 19
18
8. FRONT FINAL ASSEMBLY
309333
308300
309345
307464
309336
301320
301217
301220
309393
309452
301201
309346
309346
1
1.. Place a #309393 (N M3) nut into the hex recess atop the #301201
lower bumper.
2
2.. Place the lower bumper onto the front of the chassis.
3
3.. Thread a #309345 (SFH M3x10) screw up through the bottom of the
chassis, through the bumper, and into the M3 nut.
4
4.. Thread two #309346 (SFH M3x12) screws up through the bottom of the
chassis and into the lower bumper.
30 1201
IMPACT ABSORBING FRONT BUMPER
30 1217
COMPOSITE UPPER BUMPER SUPPORT
30 1320
FRONT BODY MOUNTS ( SET )
30 7464
PIVOT BALL 5.8 MM DOUBLE BEVEL SHOULDERS (10)
30 9333
HEX SCREW SH M3x6 (10)
30 9336
HEX SCREW SH M3x12 (10)
30 9345
HEX SCREW SFH M3x10 (10)
30 9346
HEX SCREW SFH M3x12 (10)
30 9393
NUT M3 (10)
30 9452
PIN 2x10 (10)
30 1220
FOAM BUMPER
30 8300
XRAY SHOCK ABSORBER-SET 4-STEP (2)
➊
➋
BAG
08
309345
SFH M3x10
309346
SFH M3x12
309346
SFH M3x12
309393
N M3
Attach TWO front shocks by performing the following steps.
1
1.. Attach the top of the front shock to the front shock tower.
Pass a #309336 (SH M3x12) screw through a #307464 pivot ball and shock
upper mount, and thread into the indicated hole in the front shock tower.
Tighten until the pivot ball snaps into the shock upper mount, and then
tighten the whole assembly.
2
2.. Attach the bottom of the front shock to the front lower arm.
Pass a #309336 (SH M3x12) screw through a #307464 pivot ball and shock
lower ball joint, and thread into the indicated hole in the front lower arm.
Tighten until the pivot ball snaps into the shock lower ball joint, and then
tighten the whole assembly.
309336
SH M3x12
➊
➋
➌
➍
➎
➑
➐
1
1.. Insert the front body posts into the holes of the #301217 upper bumper
support.
2
2.. Slide the #301220 foam bumper up onto the body posts; the posts should
extend down through the foam bumper.
3
3.. Position the bumper assembly onto the lower bumper.
4
4.. Secure the body posts to the lower bumper by threading two #309346
(SFH M3x12) screws upward through lower bumper into the bodyposts.
5
5.. Secure the upper bumper support to the front bulkheads with two #309333
(SH M3x6) screws.
6
6.. Glue rubber washers to the tops of the plastic body supports.
7
7.. Insert a #309452 (P 2x10) pin into a hole in a front body post. Insert the other
pin into the same hole in the other body post.
8
8.. Slide the body supports into the body posts, and snap onto the pins.
CA GLUE
➏
➊
➋
➌
➍
➍
307464
PB 5.8 mm
309333
SH M3x6
309452
P 2x10
FRONT SHOCK
(Violet spring)
FRONT SHOCK TOWER
FRONT LOWER ARM
Refer to the Set-Up Book to gain
a better understanding of different
shock mounting locations.
INITIAL POSITION