Yamaha PM1D Manager V2 Supplementary Manual - page 13
Temporary monaural setting for paired input channels/ST IN channels
13
If PAN is changed:
*1:
PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN.
*2:
This is the operation that occurs when the PAN MODE is changed in the screen. If it is changed by a scene recall, it will follow the stored PAN/BALANCE setting.
If PAIR is changed:
*1:
PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN.
*1:
PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN.
*2:
This is the operation that will occur when pairing settings are changed in the screen or panel. If pairing settings were changed as a result of a scene recall, the stored
PAN/BALANCE status will be followed.
*3:
“Parameters” refers to parameters that are linked when channels are paired.
*1:
PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN.
*2:
This is the operation that will occur when pairing settings are changed in the screen or panel. If pairing settings were changed as a result of a scene recall, the stored
PAN/BALANCE status will be followed.
*3:
“Parameters” refers to parameters that are linked when channels are paired.
PAN
*
1
→
BALANCE
BALANCE
→
PAN
.*
1
MONO mode
• BALANCE will be CENTER.*
2
• The PAN that is sent to a MIX bus that is both
paired and VARI-type will change to BALANCE,
and set to CENTER.
• The L channel PAN will be set to far left, and the
R channel PAN will be set to far right.*
2
• The BALANCE that is sent to a paired VARI-type
MIX bus will change to PAN, and panned to left
and right as above.
PAIR mode
PAIR
L-MONO
R-MONO
Cancel pairing
→
Specify pairing
Paired
→
Pairing defeated
PAN
*1
• PAN setting remains as is.
BALANCE
Paired
→
L-MONO
L-MONO
→
Paired
PAN
*1
• The PAN value of the L/R channels and the PAN
MODE setting will be temporarily preserved.
• The L/R channel PAN will be CENTER.*
2
• PAN to a paired VARI-type MIX bus will also be
set to CENTER.
• The R channel ON/OFF will be turned OFF, and
cannot be turned ON.
• The PAN/BALANCE value of the L/R channels
and the PAN MODE will return to the settings
that were in effect when the channels were
paired.*
2
• PAN to a paired VARI-type MIX bus will change
to PAN or BALANCE, and will be set to the same
value as the temporarily preserved PAN value
for TO ST.
• R-channel parameters other than PAN will be
set identically to the L channel.*
3
BALANCE
• The BALANCE value of the L/R channels and
the PAN MODE setting will be temporarily pre-
served.
• The L/R channel PAN will be CENTER.*
2
• BALANCE to a paired VARI-type MIX bus will
change to PAN, and set to CENTER.
• The R channel ON/OFF will be turned OFF.
(Cannot be turned ON.)
• PAN MODE will be set to INDIVIDUAL PAN.
Paired
→
R-MONO
R-MONO
→
Paired
PAN
*1
• The PAN value of the L/R channels and the PAN
MODE setting will be temporarily preserved.
• The L/R channel PAN will be CENTER.*
2
• PAN to a paired VARI-type MIX bus will also be
set to CENTER.
• The L channel ON/OFF will be turned OFF, and
cannot be turned ON.
• The PAN/BALANCE value of the L/R channels
and the PAN MODE will return to the settings
that were in effect when the channels were
paired.*
2
• PAN to a paired VARI-type MIX bus will change
to PAN or BALANCE, and will be set to the same
value as the temporarily preserved PAN value
for TO ST.
• L-channel parameters other than PAN will be set
identically to the R channel.*
3
BALANCE
• The BALANCE value of the L/R channels and
the PAN MODE setting will be temporarily pre-
served.
• The L/R channel PAN will be CENTER.*
2
• BALANCE to a paired VARI-type MIX bus will
change to PAN, and set to CENTER.
• The L channel ON/OFF will be turned OFF.
(Cannot be turned ON.)
• PAN MODE will be set to INDIVIDUAL PAN.