Yvc-1000 to use a wired handheld microphone by connecting to yvc-1000 ......................................................1 to use line 6 xd-v35 by connecting to yvc-1000...........................6 to use revolabs hd single/dual by connecting to yvc-1000 ... 11 contents.
1 to use a wired handheld microphone by connecting to yvc-1000 you can connect up to two handheld microphones to yvc-1000, and use them as external microphones. Voice through the external microphone is output not only to a communication partner, but also from the connected yvc-1000 speaker. With the...
2 step 1: how to connect 1. Connect the yvc-1000 audio input terminal (rca pin) and a handheld microphone with a commercially available audio cable. Before connecting the handheld microphone, turn off yvc-1000. Prepare a proper audio cable for the handheld microphone connecting terminal. Operability...
3 step 2: how to set to connect the handheld microphone to yvc-1000 for use, you have to change the yvc-1000 settings. Use the application software "yvc-1000 configurator" to change the settings. Memo this manual explains how to change the settings with a pc. Please refer to the yvc-1000 user’s manu...
4 5. Select "pa microphone" in "mode" of the terminal to which the handheld microphone is connected. 6. Select "microphone" in "signal level." 7. Test to check sound of the handheld microphone. If there is a problem, change the sound volume and tone with "yvc-1000 configurator." note voice through t...
5 ■ how to change the sound volume and tone on the assumption that the distance between the handheld microphone and your mouth is 3cm, the following values are recommended. Based on these values, change the settings according to your operation environment. Gain ：0db eq ：thru gain adjust the sensitiv...
6 to use line 6 xd-v35 by connecting to yvc-1000 you can connect up to two units of line 6 xd-v35 (digital wireless handheld mic system) to yvc-1000, and use them as external microphones. Voice through the external microphone is output not only to a communication partner, but also from the connected...
7 1. Connect the yvc-1000 audio input terminal (rca pin) and the xd-v35 receiver with a commercially available audio cable. Before connecting the xd-v35 receiver, turn off yvc-1000. Prepare a proper audio cable for the xd-v35 receiver's connecting terminal. Unbalanced 1/4 inch audio output connector...
8 4. In the "yvc-1000 configurator" window, select the "audio in" tab. 5. Set "pa microphone" in "mode" of the terminal to which the xd-v35 receiver is connected..
9 6. Select "microphone" in "signal level." 7. Test to check sound of the wireless microphone. If there is a problem, change the sound volume and tone with "yvc-1000 configurator." note voice through the wireless microphone is output not only to a communication partner, but also from the yvc-1000 sp...
10 ■ how to change the sound volume and tone on the assumption that the distance between the wireless microphone and your mouth is 3cm, the following values are recommended. Based on these values, change the settings according to your operation environment. Gain：0db eq：thru gain adjust the sensitivi...
11 to use revolabs hd single/dual by connecting to yvc-1000 you can connect one unit of revolabs hd single/dual to yvc-1000 and use it as an external microphone. Voice through the external microphone is output not only to a communication partner, but also from the connected yvc-1000 speaker. With th...
12 1. Turn off all dip switches of revolabs hd base station. 2. Connect the yvc-1000 audio input terminal (rca pin) and the out (ch1/ch2) terminal of revolabs hd base station with a commercially available audio cable. Before connecting revolabs hd base station, turn off yvc-1000. Prepare an "rca pin...
13 4. In the "yvc-1000 configurator" window, select the "audio in" tab. 5. Select "pa microphone" in "mode". Change the settings of the terminal to which the audio cable is connected..
14 6. Select "line" in "signal level." 7. Change the setting of "gain." wearable microphone: -6db handheld microphone with dedicated adapter: +6db 8. Test to check sound of the wireless microphone. If there is a problem, change the sound volume and tone with "yvc-1000 configurator." note voice throu...
15 ■ how to change the sound volume and tone based on the following recommended values, change the settings according to your operation environment. Wearable microphone: on the assumption that the distance between the wireless microphone and your mouth is 10cm, the following values are recommended: ...
