Zelmer CK1004 User Manual - page 28
29
GW17-061_v03
Technical data
The technical parameters are given on the data plate of the
product.
1.7 liter capacity.
Zelmer electric kettles are built in I class insulation and they
are equipped with supplying cord with grounding wire and
grounding plug.
The ZELMER kettle meets the requirements of the standards
in force.
The appliance is compliant with the requirements of the
following directives:
The Low Voltage Directive (LVD) – 2006/95/EC.
–
Electromagnetic Compatibility (EMC) – 2004/108/EC.
–
The product is afixed with a CE Mark on the data plate.
Structure of the kettle
(Fig. A)
1
Lid
2
Spout
3
Water level indicator
4
Handle
5
Lid opening button
6
Power base
7
ON/OFF button
8
Program selection button
9
+/– temperature adjustment buttons
10
Display
11
Storage space for the connecting cord
12
Antideposit ilter
Preparation of the electric kettle for
operation
Before the irst use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”), ill it with water up to the “max”
level, and let it boil four times (use fresh water
each time) and wash again.
Operating instructions
of the electric kettle
(Fig. B)
1
Press the lid opening button to open the lid. Place the
ilter in the kettle, if it was removed earlier.
2
Remove the kettle from its power base and ill it with
desired amount of water (the water level is shown on the
indicator).
Do not boil the water if it is below the minimum
level or beyond the maximum level on the
indicator (3).
3
After plugging the power base into the mains the display
show the letter “E”, meaning the power base is connected
appropriately, and the kettle is removed from the power
base.
4
Close the lid, and put the kettle on the stand. The LCD
shows current water temperature.
5
Press the ON/OFF button without activating any other
functions. The kettle will start boiling water until it reaches
100°C
, and then will automatically turn itself off, informing
about it by a sound signal.
6
For heating water up press the program selector button.
Singular push changes temperature. Temperature range is:
40°C, 60°C, 80°C, 90°C, 100°C
, and KEEP WARM mode at
70°C
. The given temperature will be displayed accordingly.
After setting a program, press the ON/OFF button to switch
off boiling – the display will show the correct sign.
7
When desired temperature is reached, the kettle switches
off. If the temperature programming function is used the LED
on the display will blink. Then, by pressing the ON/OFF
button it is possible to reactivate the water heating on the
previously selected program.
8
In case of KEEP WARM mode, the light display shows
70°C
. Press the “+” or “–” adjustment buttons to set the
desired temperature. The temperature is increased or
decreased by every 5°C. The available temperature range
is 50°C to 95°C. In order to start the process of maintaining
temperature on a previously selected level press the ON/
OFF button. In order to cancel the process of maintaining
temperature, press the ON/OFF button again to turn the
kettle off. Otherwise, it shall maintain temperature at
a selected level.
When in working mode, the appliance will
switch into the standby mode if no operation
has been performed by the user for 2 hours
or after pressing and holding the ON/OFF
button for 5 seconds. To return into working
mode, press and hold the ON/OFF button for
5 seconds (you will hear a single beep).
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
Be careful not to ill up with water beyond the
nominal capacity when pouring water into the
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the ilter
slowing down the speed of the low. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.