Zelmer sb1000 User Manual - Suggestion
51
SB1000-001_v05
Appliance elements
A
1
Motor unit
2
Control panel
3
Anti-slip foot
4
Cord storage compartment
5
Blender jug with level indication
6
Jug handle
7
Jug lid
8
Jug base
9
Lid stopper with level indication
10
Blade unit
11
Sealing ring
12
Grinder
13
Grinder container
14
Grinder sealing ring
15
Grinder base with blade unit
CONTROL PANEL
a
ON/OFF button
b
“–” and “+” buttons
c
“PULSE” button – enables the user to run the
momentary blending programme at a preset speed
d
“TURBO” button – enables the user to run the blending
programme at a maximum speed
e
“ICE” button – enables the user to run the ice-crushing
programme
f
Blade rotation speed indicator
The number of illuminated diodes depends on a blade
rotation speed (the higher the rotation speed, the more
diodes will be on).
Controls and Operation
B
PREPARING THE APPLIANCE FOR OPERATION
Wash the blender jug (5), lid (7) and stopper (9) in warm
water with washing-up liquid, rinse thoroughly and dry before
the first use (or after the stand blender was stored unused for
a long period of time).
Be careful with the sharp blades.
CONTROL PANEL
The blender has an illuminated control panel, which goes on
after the blender jug has been mounted (the cord is plugged
into the mains socket). When the panel illumination is on, the
appliance is ready for use.
You can use “–” and “+” to select one of 5 available blade
rotation speeds. Blade rotation speed indicator shows the
selected rotation speed, displaying 1 to 5 illuminating diodes
depending on the rotation speed. Press the ON/OFF button
to run the appliance at the chosen speed.
●
Keep the stand blender and supplying cord away from
hot surfaces and burners.
●
If it is possible, store the stand blender away from
direct sun radiation and glow-like light.
●
Never store the blender with the lid on the jug. Moisten
the lid sealing ring with water, and place the lid on the
blender jug before use.
●
Do not fill the jug over 1500 ml mark – in such case,
the content of the jug can lift the lid when the motor
starts up.
●
Do not overflow the jug. In case the liquid gets under
the motor housing, it can be vacuumed into the motor,
causing its damage.
●
After 2 minutes of work stop operation of appliance for
at least 1 minute, allowing the engine to cool down.
The process of mixing can have a maximum of ten
two-minute work cycles.
●
Do not operate when the jug is empty, as it can get
overheated.
●
The temperature of mixed ingredients should not
exceed 60°C.
SUGGESTION
Information on the product and
suggestions for its use
●
The stand blender is intended for domestic usage only.
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
●
During first start-up the appliances can emit some
odours. It is a normal phenomenon, which should be
over after a time.
Technical specification
Technical parameters are indicated on the nameplate of the
product.
Admissible time of uninterrupted operation: 2 minutes.
The time interval between two successive processes of
mixing: 10 minutes.
Maximum noise level: 85 dB/A.
The stand blender is built in 2nd isolation class. It does not
require connection to the socket equipped with grounding pin.
The stand blender meets the requirements of standards in
force.
The appliance meets the requirements of the directives:
–
Electrical equipment designed for use within specific
voltage limits (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) – 2004/108/EC.
The product is marked with CE mark on the nameplate.
For CE marking declaration of conformity please visit the
manufacturer’s website at www.zelmer.com.