Zelmer sb1000 User Manual - page 47
53
SB1000-001_v05
you feel the resistance. The control panel illumination will
go on.
6
Run the appliance.
We recommend you to use the “TURBO”
programme or set the appliance at the
maximum speed.
Set the lowest speed to obtained the best
results of grinding nuts.
Use the mill to grind one type of product only.
Grinding of various products immediately one
after another without careful washing may
result in diffusion of odour and/or flavour from
one product to another one.
The grinder should not be running
continuously for more than 30 seconds. Switch
the appliance off after 30 seconds, and wait
another 30 seconds before you run it again.
7
When the grinding has been finished, switch the
appliance off pressing the ON/OFF button
. Unplug the
appliance from the mains socket.
8
Turn the grinder anticlockwise so that the protruding
element in the grinder lid fits in the cut-out in the motor unit.
9
Remove the grinder from the motor unit.
●
Open the grinder, following the instructions set forth in
section 3 , but in a reverse order.
Always wash the grinder container and the
base with blade unit in warm water with
washing-up liquid immediately after use. Wipe
the grinder sealing ring with a damp cloth.
Cleaning and maintenance
Clean the appliance immediately after use to
prevent the deposits inside the blender jug.
●
Pour approx. 750 ml of water into the blender jug (5) and
start the appliance for about 10 seconds by pressing and
holding the “TURBO” button.
●
Remove the water from the blender jug (5), turn it upside
down and allow it to dry.
●
Wash the jug (5), lid (7), stopper (9) and blade unit (10)
in warm water with washing-up liquid, if necessary.
●
Rinse it under the stream of clean, running water, and
dry it.
●
If you left the pitcher for a long time without cleaning and
the pieces of mixed ingredients stuck to the inside of the
pitcher, use a nylon brush.
●
Do not wash the blender jug (5), lid (7), stopper (9),
coffee grinder (12) or blade unit (10) in a dishwasher.
Aggressive cleaning agents may damage the surface of
the accessories.
Always pour some water into the jug before
you start crushing ice.
Immediately after the crushing of ice or use
a mixer with loads of ice do not wash the
blender pitcher in hot water, because a large
temperature difference can break the glass.
After operation
When the appliance is no longer in use, switch it off pushing
the ON/OFF button
.
●
Use one hand to hold the motor unit (1) and the other
one to grab the jug holder (6).
●
Turn the jug anticlockwise, so that the protruding element
on the jug base fits in the cut-out in the motor unit.
Remove the blender jug from the motor unit.
●
Remove the lid (7) from the blender jug (5), pulling the
locked stopper with level indication.
●
Unplug the appliance from the mains socket if you do not
intend to use it any longer.
Grinder
C
The grinder has been designated for grinding and milling
of such ingredients as pepper, coffee beans, rice, wheat,
sesame seeds, nuts (shelled), etc., as well as for chopping
meat.
The grinder has not been designated for
grinding down very hard ingredients such as
ice cubes or nutmeg.
Never use the grinder for grinding sugar as this
may damage the appliance.
Before chopping, remove the veins,
membranes and fat from the meat, and then
chop it into pieces of approx. 2x2 cm in size.
1
Put the ingredients into the grinder container.
Do not exceed the maximum content level
indicated on the grinder container.
2
Put the grinder base (15) with blade unit into the grinder
container (13). Make sure that the grinder base sealing ring
is fixed tightly to the narrowing in the grinder container.
3
Grab the clutch cover, and turn the grinder base with
blade unit anticlockwise, until you feel the resistance.
The twisting direction is shown at the bottom
of the grinder base with blade unit.
4
Turn the grinder upside down, and mount it onto the
motor unit (1), so that one of the protruding elements in the
grinder lid fits in the cut-out in the motor unit.
5
Turn the grinder (12) clockwise to lock it in place, until