Zelmer sb1000 User Manual - page 46
52
SB1000-001_v05
Do not start the stand blender without the lid
stopper (9) in place, especially if you want
to blend solid ingredients, as they might be
ejected through the opening.
10
Select the required blade rotation speed using “–” and
“+” buttons. 1 to 5 diodes will illuminate depending on the
selected speed.
11
Start the appliance, pressing the ON/OFF button
.
The button will start blinking.
After 2 minutes of work stop operation of
appliance for at least 1 minute, allowing the
engine to cool down. The process of mixing
can have a maximum of ten two-minute work
cycles.
12
When the appliance is no longer in use, switch it off
using the ON/OFF button
.
QUICK START PROGRAMMES
Press the required button to use one of
the three available quick start programmes
(“PULSE”, “ICE”, “TURBO”).
13
“PULSE”
Pressing the “PULSE” button will cause the appliance to
run in the momentary work mode (it will run in cycles for
6-7 seconds with 6-7-second intervals) at a preset speed.
To stop the appliance, press the “PULSE” button again.
14
“TURBO”
The appliance will start processing ingredients at a maximum
speed, if the “TURBO” button is pressed and held. To stop
the appliance, release the “TURBO” button. The appliance
will stop immediately.
15
“ICE”
You can use the “ICE” programme to crush ice. This function
allows to obtain small pieces of ice of similar size.
Make sure that the stand blender is clean before
using it to crush ice. Should it be dirty, wash it
thoroughly with clean water. Any washing-up
liquid residues may affect the taste of the
crushed ice and the taste of a drink, to which
such ice will be added.
To obtain the best results of running the appliance in the
“ICE” mode, use 10-25 ice cubes per load (the cubes
should not be bigger than 2 cm in size). Add also ca. 15
ml (1 teaspoonful) of cold, fresh water. Place the jug lid
and insert the stopper, and then press the “ICE” button to
run the appliance in the momentary work mode (it will run
in cycles for 6-7 seconds with 6-7-second intervals). When
the appliance has completed ca. 5 crushing cycles, press
the “ICE” button again to stop the appliance. If you are still
dissatisfied with the results of crushing, because you want
the ice to look like snow, press and hold the “TURBO”
button for a couple of seconds.
The appliance has been equipped with quick start
programmes for user comfort. You can choose between
three programmes: “PULSE”, “ICE” and “TURBO”, using
appropriate buttons on the control panel.
ENERGY SAVING MODE
If no actions are taken for 1 minute in the stand-by mode or
when the appliance is no longer in use, the stand blender
will go to the energy saving mode (control panel illumination
goes out). If any button is pressed, the appliance will return
to the normal working mode (the control panel illumination
goes on).
CONTROLS AND OPERATION
A stand blender is designed for chopping
and mixing various kinds of products. It can
be used to prepare soups, sauces and milk
shakes, you can also mix vegetables, fruits and
meat, as well as pound cooked ingredients into
food for the infants.
1
Place the motor unit (1) on a dry, level and stable surface
near a mains socket. Make sure that the motor unit is placed
out of the reach of children.
Do not let the cord hang over the edge of
a table or work surface to prevent accidental
pulling or catching.
2
Plug the cord into the mains socket.
3
Mount the blender jug (5) onto the motor unit so that the
protruding element in the jug base fits in the cut-out in the
motor unit (1).
4
Turn the blender jug clockwise (5) to lock it in place.
5
Control panel illumination goes on.
6
Put ingredients into the blender jug (5). Do not exceed
the 1500 ml line on the blender jug. If the line is exceeded,
the content of the jug may raise jug lid (7) when the motor
is on.
The way you insert the ingredients into
a blender’s jug is free, but better results are
obtained by adding the hard components at
first.
7
Place the lid (7) onto the jug (5) before use so that its
protruding element fits in the cut-out in the jug. Press the lid
hard.
Moisten the sealing ring with water before
placing the lid (7).
8
Insert the lid stopper (9) into the opening in the lid.
Protruding elements on the lid stopper must fit in the cut-outs
in the jug lid.
9
Turn the cover cap (9) in the clockwise direction until it is
locked.