- DL manuals
- Cabletron Systems
- Switch
- CyberSWITCH CSX400
- Installation Manual
Cabletron Systems CyberSWITCH CSX400 Installation Manual
Summary of CyberSWITCH CSX400
Page 1
Cyberswitch csx400 and csx400-dc installation guide 9032692.
Page 3: Notice
Cyberswitch csx400 and csx400-dc installation guide i notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes ha...
Page 4: Industry Canada Notice
Notice ii cyberswitch csx400 and csx400-dc installation guide industry canada notice this digital apparatus does not exceed the class a limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the canadian department of communications. Le présent appar...
Page 5
Notice cyberswitch csx400 and csx400-dc installation guide iii exclusion of warranty and disclaimer of liability 1. Exclusion of warranty. Except as may be specifically provided by cabletron in writing, cabletron makes no warranty, expressed or implied, concerning the program (including its document...
Page 6: Declaration of Conformity
Notice iv cyberswitch csx400 and csx400-dc installation guide declaration of conformity application of council directive(s): 89/336/eec 73/23/eec 91/263/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative ...
Page 7: Contents
Cyberswitch csx400 and csx400-dc installation guide v contents chapter 1 introduction related documentation ...................................................................................1-1 how to use this guide ......................................................................................
Page 8
Contents vi cyberswitch csx400 and csx400-dc installation guide bridging and routing ..............................................................................2-15 bridging and routing protocol filtering................................................2-16 system passwords ..........................
Page 9
Contents cyberswitch csx400 and csx400-dc installation guide vii chapter 5 troubleshooting troubleshooting csx400 hardware ...............................................................5-4 power (pwr) led is off ..........................................................................5-4 processor...
Page 10
Contents viii cyberswitch csx400 and csx400-dc installation guide appendix a epim specifications introduction ..................................................................................................... A-1 epim-t ................................................................................
Page 11
Contents cyberswitch csx400 and csx400-dc installation guide ix appendix c modem settings for rs-232 dial-up ppp backup answer side modem configuration............................................................... C-3 appendix d specifications and standards compliance csx400, csx400-dc, and wpim en...
Page 12
Contents x cyberswitch csx400 and csx400-dc installation guide.
Page 13: Introduction
Cyberswitch csx400 and csx400-dc installation guide 1-1 1 introduction welcome to the cabletron systems cyberswitch csx400 and csx400-dc installation guide . This guide provides basic configuration information, hardware specifications and troubleshooting tips for the csx400 and csx400-dc. This guide...
Page 14: How to Use This Guide
Chapter 1: introduction 1-2 cyberswitch csx400 and csx400-dc installation guide how to use this guide this guide along with the read me first! Document, the quickset configuration guide and the quickset local management guide provide the necessary information to install and configure the csx400. Rea...
Page 15: Document Conventions
Document conventions cyberswitch csx400 and csx400-dc installation guide 1-3 document conventions the following conventions are used throughout this guide: note note symbol. Calls the reader’s attention to any item of information that may be of special importance. Tip tip symbol. Conveys helpful hin...
Page 16: Getting Help
Chapter 1: introduction 1-4 cyberswitch csx400 and csx400-dc installation guide getting help if you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact the cabletron systems global call center: before calling the cabl...
Page 17: About The Csx400
Cyberswitch csx400 and csx400-dc installation guide 2-1 2 about the csx400 the csx400 ( figure 2-1 ) is an access device that provides ethernet local area network (lan) connectivity via two ethernet port interface modules (epims), and offers high-speed wide area network (wan) access to remote sites ...
Page 18
Chapter 2: about the csx400 2-2 cyberswitch csx400 and csx400-dc installation guide • the wpim-sync provides a synchronous serial connection of up to 2.048 mbps to external communications equipment (e.G., a multiplexer or csu/dsu). The wpim-sync uses a subminiature 26-pin connector that supports the...
Page 19: Ethernet Lan Connection
Remote management capabilities cyberswitch csx400 and csx400-dc installation guide 2-3 • the wpim-t1/dds provides both a t1 and dds interface that allows you to easily switch between the two interfaces by changing the physical cabling and reconfiguring quickset for the desired interface. The wpim-t1...
Page 20: Optional Features
Chapter 2: about the csx400 2-4 cyberswitch csx400 and csx400-dc installation guide optional features rack mounting capabilities — the csx400 can be installed in a 19-inch rack with the included mounting brackets and screws. Refer to chapter 4 , installation , for complete rack mounting instructions...
Page 21: Firmware Data Compression
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-5 • network address translation (nat) routing as defined by rfc 1631 • point-to-point protocol (lcp) as defined by rfc 1661 • point-to-point protocol (bncp) as defined by rfc 1638 • point-to-point protocol (ipcp) as define...
Page 22: Inverse Multiplexing (Imux)
Chapter 2: about the csx400 2-6 cyberswitch csx400 and csx400-dc installation guide inverse multiplexing (imux) cabletron systems inverse multiplexing (imux) feature provides enhanced throughput for users by doing each of the following: • the imux function evenly distributes a data packet stream fro...
Page 23: Dhcp and Nat
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-7 dhcp and nat the dynamic host configuration protocol (dhcp) and network address translation (nat) method eliminates the expense of purchasing limited public ip addresses for each client on a local network, and the need t...
Page 24: Frame Relay Protocol
Chapter 2: about the csx400 2-8 cyberswitch csx400 and csx400-dc installation guide frame relay protocol frame relay can be defined as a “packet mode” service, organizing data into individually addressed units known as “frames”. Frame relay eliminates all layer 3 processing. Only a few layer 2 funct...
Page 25: Pap and Chap Security
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-9 point-to-point protocol (ppp) ppp is a data link layer industry standard wan protocol for transferring multi-protocol data traffic over point-to-point connections. It is suitable for both high-speed synchronous ports as ...
Page 26: Lqm
Chapter 2: about the csx400 2-10 cyberswitch csx400 and csx400-dc installation guide the peer device challenges the authenticator device by generating a chap challenge, and the challenge contains an md5 algorithm with a random number that has your encrypted password and system name. The authenticato...
Page 27: Isdn Back-Up
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-11 a network terminator device (nt1) provides the interface between isdn terminal (router) equipment and the isdn service provider. In the u.S., the nt1 is provided by the customer; outside the u.S., the nt1 is provided by...
Page 28: The Ip-Ospf Routing Protocol
Chapter 2: about the csx400 2-12 cyberswitch csx400 and csx400-dc installation guide input idle time-out — input idle time-out allows you to determine the amount of time necessary for data packets to be received, before the interface is automatically disconnected. Output idle time-out — output idle ...
Page 29
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-13 every autonomous system within an ospf routing domain must have a backbone. An ospf backbone distributes routing information between areas in an autonomous system and consists of all area border routers, any networks no...
Page 30: Hdsl
Chapter 2: about the csx400 2-14 cyberswitch csx400 and csx400-dc installation guide the designated router is chosen from the list of eligible routers. If a one or more routers have declared itself to be the dr in their hello packets, the one with the highest router priority becomes the dr. If no ro...
Page 31: Bridging and Routing
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-15 bridging and routing bridging — bridging connects two or more separate networks together. The bridge examines a portion of each network frame called the header. This header contains control information for the frame. Th...
Page 32
Chapter 2: about the csx400 2-16 cyberswitch csx400 and csx400-dc installation guide ieee 802.1d bridging — the csx400 supports the ieee 802.1d standard for lan to lan bridging. Bridging is provided over ppp and frame relay as well as adjacent lan ports. The bridging software uses transparent bridgi...
Page 33: System Passwords
Csx400 firmware support cyberswitch csx400 and csx400-dc installation guide 2-17 bridge filtering — bridge filtering allows a network administrator to control the flow of packets across the csx400. Bridge filtering can be used to “deny” or “allow” packets based on a “matched pattern” using a specifi...
Page 34: Redundancy Vs Backup
Chapter 2: about the csx400 2-18 cyberswitch csx400 and csx400-dc installation guide redundancy vs backup cabletron wan devices with more than one wan channel offer two forms of recovery from failure on one of the wan channels. These two forms of recovery can best be categorized as “redundant” and “...
Page 35
Redundancy vs backup cyberswitch csx400 and csx400-dc installation guide 2-19 table 2-1 , below, shows the supported configurations at the initial release of the backup feature. Simple network management protocol (snmp) the csx400 provides snmp agent support for the following: standard and enterpris...
Page 36
Chapter 2: about the csx400 2-20 cyberswitch csx400 and csx400-dc installation guide • ppp bncp mib rfc1474 (bridge network control protocol) • ipxcp mib rfc1552 • frame relay dte mib rfc2115 • security mib rfc1472 (ccp, pap, and chap) • rs-232 mib rfc1317 • lqm mib rfc1989 • ppp mp mib rfc1990 • fr...
Page 37
Redundancy vs backup cyberswitch csx400 and csx400-dc installation guide 2-21 • environmental temperature hot trap type code #282(0x11a) rrev4-mib • environmental temperature normal trap type code #284(0x11c) rrev4-mib • ip event log change trap type code #1280(0x500) ctip-mib the following is a lis...
Page 38
Chapter 2: about the csx400 2-22 cyberswitch csx400 and csx400-dc installation guide • ipx mtu size has been changed on interface # • ipx framing type has been changed on interface # • ipx has detected link up on interface # • ipx has detected link down on interface # • ipx primary address has been ...
Page 39: Network Requirements
Cyberswitch csx400 and csx400-dc installation guide 3-1 3 ethernet cabling requirements this chapter contains general networking guidelines. Before attempting to install the csx400 or any additional epims or wpims, review the requirements and specifications outlined in this chapter. Network requirem...
Page 40
Chapter 3: ethernet cabling requirements 3-2 cyberswitch csx400 and csx400-dc installation guide 10base-t twisted pair network when connecting a 10base-t segment to either of the csx400 ethernet interfaces (twisted pair ethernet port interface module [epim-t]), ensure that the network meets the foll...
Page 41
Network requirements cyberswitch csx400 and csx400-dc installation guide 3-3 temperature — multi-pair pvc 24 awg telephone cables typically have an attenuation of approximately 8–10 db/100 m at 20 ° c (68 ° f). The attenuation of pvc insulated cable varies significantly with temperature. At temperat...
Page 42
Chapter 3: ethernet cabling requirements 3-4 cyberswitch csx400 and csx400-dc installation guide single mode fiber optic network when connecting a single mode fiber optic link segment to the csx400 (using an epim-f3), ensure that the network meets the following requirements: cable type — fiber optic...
Page 43: Transceiver Requirements
Network requirements cyberswitch csx400 and csx400-dc installation guide 3-5 connectors — you can use up to 29 t-connectors throughout the length of the cable segment for host connections. Ensure that all connections are spaced 0.5 meters or more from one another or from terminators. If you use an e...
Page 44
Chapter 3: ethernet cabling requirements 3-6 cyberswitch csx400 and csx400-dc installation guide.
Page 45: Installation
Cyberswitch csx400 and csx400-dc installation guide 4-1 4 installation this chapter outlines the procedure for attaching the csx400 to the network. Ensure that the network meets the guidelines and requirements outlined in chapter 3 , ethernet cabling requirements , before installing the csx400. To i...
Page 46: Installing Interface Modules
Chapter 4: installation 4-2 cyberswitch csx400 and csx400-dc installation guide • in a shelf installation, the shelf must be able to support 13.6 kg (30 lb) of static weight for each device on the shelf. • maintain a temperature of between 5°c (41°f) and 40°c (104°f) at the installation site with fl...
Page 47
Installing interface modules cyberswitch csx400 and csx400-dc installation guide 4-3 to install an epim, perform the following steps: 1. Attach the disposable grounding strap to your wrist (refer to the instructions outlined on the disposable grounding strap package). 2. Remove the coverplate or the...
Page 48: Removing The Csx400 Cover
Chapter 4: installation 4-4 cyberswitch csx400 and csx400-dc installation guide removing the csx400 cover this section describes how to remove the csx400 chassis cover. The cover must be removed to install a wan port interface module. To remove the chassis cover, proceed as follows: 1. Disconnect th...
Page 49: Removing The Csx400-Dc Cover
Installing interface modules cyberswitch csx400 and csx400-dc installation guide 4-5 removing the csx400-dc cover this section describes how to remove the csx400-dc chassis cover. The cover must be removed to install a wan port interface module (wpim). To remove the chassis cover, proceed as follows...
Page 50
Chapter 4: installation 4-6 cyberswitch csx400 and csx400-dc installation guide installing wan port interface modules (wpims) to install a wpim into the csx400, refer to figure 4-3 and complete the following steps: 1. Attach the disposable grounding strap to your wrist (refer to the instructions out...
Page 51
Installing interface modules cyberswitch csx400 and csx400-dc installation guide 4-7 figure 4-3 installing wpims wpim wpim screws standoffs wpim connector pins wpim connector.
Page 52: Csx-Comp/encr Installation
Chapter 4: installation 4-8 cyberswitch csx400 and csx400-dc installation guide csx-comp/encr installation this section contains instructions on how to install the csx-comp/encr into the csx400 motherboard. To help eliminate any potential problems during or after installation, read and understand al...
Page 53: Installing The Csx400
Installing the csx400 cyberswitch csx400 and csx400-dc installation guide 4-9 figure 4-4 csx-comp/encr installing the csx400 the csx400 may be installed on a tabletop, shelf or in a 19-inch rack. Refer to tabletop and shelf installations for information concerning a tabletop or shelf installation. C...
Page 54
Chapter 4: installation 4-10 cyberswitch csx400 and csx400-dc installation guide 2. Peel the paper backing off the round rubber feet, and adhere them to the bottom of the csx400. Place one rubber foot near each of the four corners of the csx400, and evenly space the remaining two near the center. Fi...
Page 55
Installing the csx400 cyberswitch csx400 and csx400-dc installation guide 4-11 materials required the following parts are included with the csx400: • left (p/n 8501242-01) and right (p/n 8501241-01) rackmount brackets ( figure 4-6 ). • 6-32 x 1/4 inch flat-head screws (4) figure 4-6 csx400 and csx40...
Page 56
Chapter 4: installation 4-12 cyberswitch csx400 and csx400-dc installation guide 3. Using the four 6-32 x 1/4 inch flat-head screws, attach the rackmount brackets to the sides of the csx400 as shown in figure 4-7 . Figure 4-7 installing the rackmount brackets 4. Position the csx400 between the verti...
Page 57
Installing the csx400 cyberswitch csx400 and csx400-dc installation guide 4-13 4. Locate the four 6-32 x 3/8-inch flathead cover replacement screws in the rackmount kit. Use these screws to attach the rackmount brackets to the csx400-dc as shown in figure 4-8 . Figure 4-8 installing the rackmount br...
Page 58
Chapter 4: installation 4-14 cyberswitch csx400 and csx400-dc installation guide connecting the csx400 to the power source to connect the csx400 to the power source, perform the following steps: 1. Plug the power cord into the back panel of the csx400. 2. Plug the other end of the power cord into a ...
Page 59
Connecting the csx400-dc to the power source cyberswitch csx400 and csx400-dc installation guide 4-15 connecting the csx400-dc to the power source th csx400-dc requires either a 48 vdc or 60 vdc (48/60 vdc), 3.5 a (maximum), external power source supplied by three 18 awg (american wire gauge) copper...
Page 60
Chapter 4: installation 4-16 cyberswitch csx400 and csx400-dc installation guide figure 4-10 48/60 vdc power supply connections 1. Connect the ground terminal of the dc input power strip to an appropriate earth ground (green wire from power supply). 2. Refer to figure 4-10 for the proper connections...
Page 61: Troubleshooting
Cyberswitch csx400 and csx400-dc installation guide 5-1 5 troubleshooting use this chapter in conjunction with the lanview status monitoring and diagnostic leds on the csx400 to diagnose power failures, collisions, cable faults and link problems. Figure 5-1 shows the front panel leds. Table 5-1 , ta...
Page 62
Chapter 5: troubleshooting 5-2 cyberswitch csx400 and csx400-dc installation guide table 5-2 csx400 lan led states led color state receive (rcv) off port enabled, no activity amber (flashing) receiving traffic collision (cln) off normal red collision link (lnk) off power off or failure green normal,...
Page 63
Troubleshooting cyberswitch csx400 and csx400-dc installation guide 5-3 table 5-4 csx400 wan led states for sts 1 wpim color state t1, di, and e1 off normal or port disabled red red alarm dds off normal or port disabled amber out of service (oos) sync off inactive or disabled green request to send (...
Page 64: Power (Pwr) Led Is Off
Chapter 5: troubleshooting 5-4 cyberswitch csx400 and csx400-dc installation guide troubleshooting csx400 hardware power (pwr) led is off • check that the power connection is firmly attached to the back panel of the csx400, and the other end to an active power source. Processor (cpu) led is off if t...
Page 65: Troubleshooting The Wan
Troubleshooting the wan cyberswitch csx400 and csx400-dc installation guide 5-5 troubleshooting the wan link (lnk) led is off the wan interface is not configured for operation. • use quickset or local management to make sure that the wan interface is configured correctly. Link (lnk) led is red the w...
Page 66: Status 1 (Sts1) Led Is Red
Chapter 5: troubleshooting 5-6 cyberswitch csx400 and csx400-dc installation guide wpim-sync installed in csx400 the port is operating normally. If it is not, and this led is off the port may be disabled or rts may be inactive. • use quickset or local management to make sure that the wan interface o...
Page 67: Status 1 (Sts1) Led Is Amber
Troubleshooting the wan cyberswitch csx400 and csx400-dc installation guide 5-7 wpim-hdsl installed in csx400 wpim-hdsl is configured for either full or fractional t1 and the wpim is not able to establish synchronization on loop 1 with the remote hdsl circuit. • use quickset or local management to v...
Page 68: Status 2 (Sts2) Led Is Off
Chapter 5: troubleshooting 5-8 cyberswitch csx400 and csx400-dc installation guide wpim-hdsl is installed in csx400 the port is operating normally, loop 1 has synchronized with the hdsl circuit at the remote end. Wpim-s/t is installed in csx400 the port is operating normally, isdn bri channel b1 or ...
Page 69: Status 2 (Sts2) Led Is Amber
Troubleshooting the wan cyberswitch csx400 and csx400-dc installation guide 5-9 status 2 (sts 2) led is red wpim-hdsl installed in csx400 wpim-hdsl is configured for either full t1 and the wpim is not able to establish synchronization on loop 2 with the remote hdsl circuit. • verify using quickset o...
Page 70
Chapter 5: troubleshooting 5-10 cyberswitch csx400 and csx400-dc installation guide wpim-hdsl installed in csx400 the port is operating normally, loop 2 has synchronized with the hdsl circuit at the remote end (full t1 mode only). Wpim-s/t installed in csx400 the port is operating normally, isdn bri...
Page 71
Investigating software configuration problems cyberswitch csx400 and csx400-dc installation guide 5-11 user cannot communicate with remote network station if bridging, • check that the bridging default destination is set. • check that bridging to/from the remote router is set on. • be sure to reboot...
Page 72
Chapter 5: troubleshooting 5-12 cyberswitch csx400 and csx400-dc installation guide synchronous polling messages — the t391 timer for the ansi/itu frame relay forms the basis for polling between the fr switch and the fr dte (us). We transmit a status enquiry every t391 seconds (10 by default) to the...
Page 73: Epim Specifications
Cyberswitch csx400 and csx400-dc installation guide a-1 a epim specifications introduction the csx400 provides two ports for cabletron systems epims. Epims allow connection to the main network using different media types. The following sections explain the specifications of the variety of epims cabl...
Page 74: Epim-F2
Appendix a: epim specifications a-2 cyberswitch csx400 and csx400-dc installation guide epim-f2 the epim-f2 supports multimode fiber optic cabling. It has an internal cabletron systems fot-f fiber optic transceiver and is equipped with st connectors. Figure a-2 shows the epim-f2. Specifications for ...
Page 75
Epim-f2 cyberswitch csx400 and csx400-dc installation guide a-3 table a-2 provides transmitter power parameters. Table a-2 transmitter power parameter typical value worst case worst case budget typical budget 50/125 µm fiber -13.0 dbm -15.0 dbm 13.0 db 17.5 db 62.5/125 µm fiber -10.0 dbm -12.0 dbm 1...
Page 76: Epim-F3
Appendix a: epim specifications a-4 cyberswitch csx400 and csx400-dc installation guide epim-f3 the epim-f3 supports single mode fiber optic cabling. It has an internal cabletron systems fot-f fiber optic transceiver and is equipped with st connectors. Figure a-3 shows the epim-f3. Specifications fo...
Page 77: Epim-C
Epim-c cyberswitch csx400 and csx400-dc installation guide a-5 epim-c the epim-c supports thin coaxial cabling and is equipped with an internal cabletron systems tms-3 transceiver. You can use the term switch on the front of the epim-c to set the internal 50-ohm terminator. This eliminates the need ...
Page 78: Epim-A and Epim-X (Aui Port)
Appendix a: epim specifications a-6 cyberswitch csx400 and csx400-dc installation guide epim-a and epim-x (aui port) the epim-a is a db15 female connector used to attach segments to an external transceiver. The epim-x is equipped with dual internal transceivers. It has a db15 male connector used to ...
Page 79: Wpim Cable Specifications
Cyberswitch csx400 and csx400-dc installation guide b-1 b wpim cable specifications wpim-t1 this section provides the cabletron systems part number and connector specifications for wpim-t1 interface cables. Table b-1 provides connector type and part number information. Table b-2 provides rj48 connec...
Page 80
Appendix b: wpim cable specifications b-2 cyberswitch csx400 and csx400-dc installation guide table b-3 provides rj48 dte pin assignments. Table b-4 provides rj48 network pin assignments. Table b-3 dte pin assignments pin signal 1 receive ring 2 receive tip 3 not used 4 transmit ring 5 transmit tip ...
Page 81: Wpim-Sy
Wpim-sy cyberswitch csx400 and csx400-dc installation guide b-3 wpim-sy this section provides the cabletron systems part number and connector specifications for the wpim-sy interface cables. Table b-5 provides the cable and interface types, electrical types, and part numbers for the wpim-sy. Table b...
Page 82: Eia-449
Appendix b: wpim cable specifications b-4 cyberswitch csx400 and csx400-dc installation guide eia-449 table b-6 shows the connector number, cable assembly description, and connector type. Table b-7 provides pin assignments for the eia-449 interface cable. Table b-6 eia-449 interface connector number...
Page 83: V.35
Wpim-sy cyberswitch csx400 and csx400-dc installation guide b-5 v.35 table b-8 shows the connector number, cable assembly description, and connector type. Table b-9 provides pin assignments for the v.35 interface cable. Ce dte ring indicator 22 15 incoming call dte ic tm test mode 25 18 test mode tm...
Page 84
Appendix b: wpim cable specifications b-6 cyberswitch csx400 and csx400-dc installation guide db dte transmit signal timing a 15 e y transmitter signal timing a dte 114 transmit signal timing b 12 aa transmitter signal timing b dd receive signal timing a 17 f v receiver signal timing a 115 receive s...
Page 85: Eia-232
Wpim-sy cyberswitch csx400 and csx400-dc installation guide b-7 eia-232 table b-10 shows the connector number, cable assembly description, and connector type. Table b-11 provides pin assignments for the eia-232 interface cable. Table b-10 eia-232 interface connector number cable assembly description...
Page 86: X.21
Appendix b: wpim cable specifications b-8 cyberswitch csx400 and csx400-dc installation guide x.21 table b-12 shows the connector number, cable assembly description, and connector type. Table b-13 provides pin assignments for the x.21 interface cable. Table b-12 x.21 interface connector number cable...
Page 87
Wpim-sy cyberswitch csx400 and csx400-dc installation guide b-9 eia-530, eia-530 alt a, eia-530 a, and eia-530 a alt a table b-14 shows the connector number, cable assembly description, and connector type for the eia-530, eia-530 alt a, eia-530a, and eia-530a alt a, interface cables. Table b-15 prov...
Page 88
Appendix b: wpim cable specifications b-10 cyberswitch csx400 and csx400-dc installation guide db dte transmit signal timing a 15 e 15 transmit signal timing a dte db transmit signal timing b 12 12 transmit signal timing b dd receive signal timing a 17 f 17 receive signal timing a dd receive signal ...
Page 89: Wpim-Dds
Wpim-dds cyberswitch csx400 and csx400-dc installation guide b-11 wpim-dds this section provides cabletron systems part number and connector specifications for the wpim-dds interface cable. The wpim-dds has one rj45 port for a direct connection to a single digital data service (dds) circuit. Table b...
Page 90: Wpim-E1
Appendix b: wpim cable specifications b-12 cyberswitch csx400 and csx400-dc installation guide wpim-e1 this section provides the cabletron systems part number and connector specifications for the wpim-e1 interface cable. Table b-18 shows the wpim-e1 connector number, cable and interface type, connec...
Page 91
Wpim-e1 cyberswitch csx400 and csx400-dc installation guide b-13 table b-20 provides wpim-e1 dte interface cable pin assignments. Table b-21 provides wpim-e1 rj45 network interface cable pin assignments. Table b-20 dte interface pin signal 1 receive ring 2 receive tip 3 shield ground 4 transmit ring...
Page 92: Wpim-Di
Appendix b: wpim cable specifications b-14 cyberswitch csx400 and csx400-dc installation guide wpim-di this section provides cabletron systems part number and connector specifications for the wpim-di interface cables. Table b-22 shows the connector number, cable assembly description, cable and inter...
Page 93: Wpim-Hdsl
Wpim-hdsl cyberswitch csx400 and csx400-dc installation guide b-15 table b-24 provides the wpim-di drop and insert interface cable pin assignments. Wpim-hdsl this section provides connector specifications for the wpim-hdsl interface cables. Table b-25 provides pin assignments for the rj-45 network i...
Page 94: Wpim-S/t
Appendix b: wpim cable specifications b-16 cyberswitch csx400 and csx400-dc installation guide wpim-s/t this section provides connector specifications for the wpim-s/t interface cable. Table b-26 provides pin assignments for the rj-45 network interface connector. Table b-26 wpim-s/t network interfac...
Page 95
Cyberswitch csx400 and csx400-dc installation guide c-1 c modem settings for rs-232 dial-up ppp backup this appendix details the backup configuration of a frame relay or ppp nailed-up connection using modems. The modem used in this example is the fastpro ii (gdc 060r124-000) from general datacomm. A...
Page 96
Appendix c: modem settings for rs-232 dial-up ppp backup c-2 cyberswitch csx400 and csx400-dc installation guide the caller side must be configured for the following: • dtr off to on transition causes modem to automatically dial previously stored phone number. • data mode of operation set to call pl...
Page 97
Answer side modem configuration cyberswitch csx400 and csx400-dc installation guide c-3 answer side modem configuration the answer side must be configured for the following: • ignore dtr state. • normal dsr operation. Using the extended at(tention) command set listed in the following table to config...
Page 98
Appendix c: modem settings for rs-232 dial-up ppp backup c-4 cyberswitch csx400 and csx400-dc installation guide.
Page 99
Cyberswitch csx400 and csx400-dc installation guide d-1 d specifications and standards compliance this chapter contains hardware specifications, and safety and compliance standards for the csx400, csx400-dc, and for the individual wpims that can be configured with these devices. Csx400, csx400-dc, a...
Page 100
Appendix d: specifications and standards compliance d-2 cyberswitch csx400 and csx400-dc installation guide csx400-dc specifications and compliance standards csx400 and csx400-dc regulatory compliance safety — this unit meets the safety requirements of ul 1950, csa c22.2 no. 950 and en 60950, iec 95...
Page 101: Wpim-Ti
Individual wpim regulatory compliance cyberswitch csx400 and csx400-dc installation guide d-3 individual wpim regulatory compliance the following sections provide regulatory compliance standards for the wpim-ti, wpim-sy, wpim-dds, wpim-e1, wpim-di, wpim-s/t, and the wpim-hdsl. Cabletron systems rese...
Page 102: Wpim-Sy
Appendix d: specifications and standards compliance d-4 cyberswitch csx400 and csx400-dc installation guide wpim-sy this section describes the environmental specifications and safety and approval requirements for the wpim-sy. Safety — this unit meets the safety requirements of ul1950, csa c22.2 no. ...
Page 103: Wpim-E1
Individual wpim regulatory compliance cyberswitch csx400 and csx400-dc installation guide d-5 wpim-e1 this section describes the environmental specifications and safety and approval requirements for the wpim-e1. Safety — this unit meets the safety requirements of en 60950, iec 950, 73/23/eec and as/...
Page 104: Wpim-Hdsl
Appendix d: specifications and standards compliance d-6 cyberswitch csx400 and csx400-dc installation guide wpim-hdsl this section describes the environmental specifications and safety and approval requirements for the wpim-hdsl. Safety — this unit meets the safety requirements of uc1950, csa 22.2 n...
Page 105
Cyberswitch csx400 and csx400-dc installation guide e-1 e network information worksheets table e-1 csx400 configuration section item setting system settings router name message system settings dial authentication password dial authentication password/secret system settings isdn settings isdn spid #1...
Page 106
Appendix e: network information worksheets e-2 cyberswitch csx400 and csx400-dc installation guide remote router database tcp/ip route addresses remote network’s ip addresses, subnet masks, and metrics source wan ip address and subnet mask a remote wan ip address and subnet mask b remote router data...
Page 107: Csx400 and Csx400-Dc
Cyberswitch csx400 and csx400-dc installation guide f-1 f fcc part 68 - user’s information for csx400 and csx400-dc the following instructions are to ensure compliance with the federal communications commission (fcc) rules, part 68: 1. All connections to the wpim-t1, wpim-di and wpim-dds must be mad...
Page 108
Appendix f: fcc part 68 - user’s information for csx400 and csx400-dc f-2 cyberswitch csx400 and csx400-dc installation guide 3. If the unit appears to be malfunctioning, it should be disconnected from the telephone lines until you learn if your equipment or the telephone line is the source of the t...
Page 109
Fcc part 68 - user’s information for csx400 and csx400-dc cyberswitch csx400 and csx400-dc installation guide f-3 affidavit for the connection ofcustomer equipment to 1.544 mbps and/or subrate digital services for the work to be performed in the certified territory of telco’s name: state of: country...
Page 110
Appendix f: fcc part 68 - user’s information for csx400 and csx400-dc f-4 cyberswitch csx400 and csx400-dc installation guide i attest that the operator(s) maintainer(s) of the digital cpe responsible for the establishment, maintenance and adjustment of the encoded analog content and billing informa...
Page 111: Glossary
Cyberswitch csx400 and csx400-dc installation guide g-1 g glossary 10base-t — ieee 802.3 standard for the use of ethernet lan technology over unshielded twisted pair wiring, running at 10 mbps. Arp — address resolution protocol. An internet protocol used to bind an ip address to ethernet/ 802.3 addr...
Page 112
Glossary g-2 cyberswitch csx400 and csx400-dc installation guide dhcp — dynamic host configuration protocol is a protocol for automatic tcp/ip configuration that provides static and dynamic address allocation and management. Dial on demand — dial up wan resources are accessed only when remote access...
Page 113
Glossary cyberswitch csx400 and csx400-dc installation guide g-3 ip address — internet address. A 32-bit address assigned to devices that participate in a network using tcp/ip. An ip address consists of four octets separated with periods defining network, optional subnet and host sections. Ipx (inte...
Page 114
Glossary g-4 cyberswitch csx400 and csx400-dc installation guide network layer — layer 3 of the osi reference model that provides the protocol routing function. Node — refers to a termination point for communication links; entity that can access a network. Osi — open system interconnection. An inter...
Page 115
Glossary cyberswitch csx400 and csx400-dc installation guide g-5 serialization frames — frames sent out by servers under ipx to check whether illegal copies of netware are in use on the network. Service advertising protocol — protocol used in ipx for broadcasting information about services available...
Page 116
Glossary g-6 cyberswitch csx400 and csx400-dc installation guide transparent bridging — bridging technique used in ethernet networks that allows transfer of frames across intermediate nodes using tables associating end nodes with bridging addresses. Bridges are unknown to the end nodes. Udp — user d...
Page 117: Index
Cyberswitch csx400 and csx400-dc installation guide index-1 index numerics 10base2 grounding 3-5 link length 3-4 specifications 3-4 10base-f attenuation multimode 3-3 single mode 3-4 link length multimode 3-3 single mode 3-4 specifications 3-3 10base-t impedance 3-2 insertion loss 3-2 link length 3-...
Page 118
Index index-2 cyberswitch csx400 and csx400-dc installation guide l lan support 2-3 link length 10base2 3-4 10base-f multimode 3-3 single mode 3-4 10base-t 3-2 m mib support 2-19 n network address translator (nat) 2-7 network information worksheets b-1 , e-1 p pap 2-9 point-to-point protocol (ppp) 2...