ECX Torment ECX4000 Instruction Manual - Maintenance
9
EN
ShOCk CLEANING
Oil-filled shocks will require regular maintenance due to the oil
breaking down or getting dirty. This maintenance should be performed
after about every 3 to 5 hours of use, depending on the conditions that
the vehicle is used in.
• Remove the shock from the vehicle.
• Remove the cap from the shock body and dispose of fluid.
• Disassemble the shock. Clean thoroughly with DYN5505.
Dry parts before assembly.
• Assemble the shock and refill the shock body with silicone
fluid (30 weight recommended).
• Slowly move the shaft and piston up and down to remove
air bubbles.
• Move the piston to the midway point of the body and install
the cap.
• Wipe off any overflowing fluid.
• When properly filled, the piston should rebound about 3/8 in
(9.5mm) after being pushed in fully.
• Install the shock on the vehicle.
Ride height Adjustment
Ride height is an adjustment that affects the way the vehicle
jumps, turns and goes over bumps. Drop one end of the vehicle from
approximately 6 inches (152 mm) in height onto a flat surface. When
dropping the front of the vehicle, after the vehicle settles, make
sure the front arms are equal and parallel to the flat surface. Do
the same with the rear to make sure both arms are parallel with
the flat surface.
Lower the front ride height to increase steering. Lower the rear
ride height to increase traction but decrease steering.
REAR ShOCk
FRONT ShOCk
Part #
Description
ECX1036
Shock Body Set
ECX1037
Shock Caps, Pistons
ECX1038
Shock Parts Set
ECX1039
Front Shock Shaft (2)
ECX1040
Rear Shock Shaft (2)
ECX1041
Front Shock Springs (2)
ECX1042
Rear Shock Springs (2)
ECX1043
Shock O-Ring Set
MAINTENANCE
No. Description
TAPPING BINDER HEAD M3 x 10mm
TAPPING BINDER HEAD M3 x 12mm
TAPPING FLAT HEAD M3 x 15mm
TAPPING FLAT HEAD M3 x 12mm
TAPPING FLAT HEAD M3 x 10mm
TAPPING BINDER HEAD M3 x 18mm
TAPPING FLAT HEAD M2 x 16mm
TAPPING BINDER HEAD M3 x 16mm
No. Description
BUTTON HEX M2.5 x 4mm
SETSCREW M3 x 3mm
SETSCREW M3 x 12mm
STEP SCREW M3 x 0.5 x 13.4mm
STEP SCREW M3 x 0.5 x 10.5mm
BUTTON HEX M2.5 x 8mm
STEP SCREW M3 x 0.5 x 7.4mm
No. Description
BINDER HEAD M3 x 8mm
BINDER HEAD M3 x 12mm
BINDER HEAD M3 x 20mm
BINDER HEAD M3 x 25mm
BUTTON HEAD M3 x 30mm
BUTTON HEAD M2 x 6mm
TAPPING BUTTON HEAD M3 x 10mm
No. Description
WASHER 5 x 7 x 0.5mm
E-CLIP E2.5
LOCK WASHER
FLANGED LOCK NUT M4
WASHER 3 x 8 x 0.5mm
LOCK NUT M3
WASHER 2 x 7 x 0.5mm
SET SHAFT SCREW M3 x 13mm
Front Shock
ECX1043
ECX1037
ECX1037
ECX1041
ECX1037
ECX1043
Rear Shock
ECX1036
ECX1038
ECX1038
ECX1043
ECX1037
ECX1037
ECX1038
ECX1042
ECX1040
ECX1057
ECX1037
ECX1043
ECX1038
ECX1039
ECX1036
ECX1038
ECX1038
ECX1037
ECX1057
FASTENERS