1. DL manuals
  2. FRANCO
  3. Humidifier
  4. UCP
  5. Instruction Manual For Use And Maintenance

FRANCO UCP Instruction Manual For Use And Maintenance

Manual is about: CENTRIFUGAL HUMIDIFIER

Summary of UCP

  • Page 1

    Instruction manual for use and maintenance ucp centrifugal humidifier t r a ns la t e d v e r s i o n f r o m i ta li a n t o e n g l i s h before installing or running the unit, it is obligatory to carefully read and consult this manual. Manual version: 02-000/2010 franco srl – via nazionale, 80 12...

  • Page 2

    Franco srl manual of use and maintenance ucp 2.

  • Page 3

    Franco srl manual of use and maintenance ucp 3 index index ...................................................................................................................................... 3 1 - introduction...........................................................................................

  • Page 4

    Franco srl manual of use and maintenance ucp 4 1 - introduction 1.1 general warnings this device should be used only for the functions for which it was intended "adiabatic cooler – humidifier”. Any other use is to be considered improper and dangerous. Franco srl cannot be held liable for any damages...

  • Page 5

    Franco srl manual of use and maintenance ucp 5 1.3 covenants used throughout this manual the manual is divided into autonomous chapters, each of which is addressed to a specific operator’s figure (installer, operator and maintainer), for which the skills needed to operate the machine safely have bee...

  • Page 6

    Franco srl manual of use and maintenance ucp 6 1.5 recipients the manual is addressed to: the installer, the operator, and the qualified personnel entitled to the maintenance of the device. Exposed person: refers to any person exposed, wholly or partially, to a danger zone; operator: refers to those...

  • Page 7

    Franco srl manual of use and maintenance ucp 7 other definitions: human-machine interaction: any situation in which an operator interacts with the machine in any of the operational phases at any time of the life of the machine itself; operator’s qualification: minimum level of competence that an ope...

  • Page 8

    Franco srl manual of use and maintenance ucp 8 pictographs concerning the operator’s qualification symbol description generic laborer: operator lacking of specific competences, capable of performing only simple tasks under the control of qualified technicians. Lifting and handling vehicles driver: o...

  • Page 9

    Franco srl manual of use and maintenance ucp 9 pictographs concerning safety the pictograms contained in a triangle indicate danger. The pictograms contained in a circle impose prohibition / obligation. Pictograph denomination hazardous voltage. Entanglement. Dragging. General danger. Do not remove ...

  • Page 10

    Franco srl manual of use and maintenance ucp 10 1.7 applications in the industrial field, the machine is installed in places where it is necessary to maintain a certain humidity level, for example in fruits and vegetable refrigerating rooms, in aging warehouses, in the paper and tobacco industries, ...

  • Page 11

    Franco srl manual of use and maintenance ucp 11 spinning disk spinning disk cap tank lid rear shelter float valve recirculation pump nozzle electric motor water supplì connection ½” water flow regulating valve fast connection drain holeo ⅜ ” with cap. Fixed disk 1.10 description of the parts constit...

  • Page 12

    Franco srl manual of use and maintenance ucp 12 1.12 warranty this device is guaranteed for 12 months from the date of manufacture for all failures attributed to a proven manufacturing or material defect. All the parts damaged by transport, improper maintenance, negligence, inability to use, imprope...

  • Page 13

    Franco srl manual of use and maintenance ucp 13 1.15 declaration of incorporation (att. Iib dir. 2006/42/ce) the manufacturer franco s.R.L. Company via nazionale, 80 12010 cn address postal code province cervasca italy city country declares that the partly complete machine cooler / humidifier ucp1 /...

  • Page 14

    Franco srl manual of use and maintenance ucp 14 2 - installation 2.1 before installing in order to start the humidifier / cooler ucp, the following conditions are required: • connection to the electric power supply with voltage and frequency suitable for the machine and with grounding and safety dev...

  • Page 15

    Franco srl manual of use and maintenance ucp 15 the installment of the machine must meet the safety distance and protections in accordance with the norm din en 294 – 4, 4.1, 4.2. The machine must be placed at least at 2.5 meters above the ground level (if used without protections. Fig. 2.2 - a.T.U. ...

  • Page 16

    Franco srl manual of use and maintenance ucp 16 3 - operation 3.1 getting started before operating the humidifier, verify that: 1. All connections, both electrical and hydraulic, are made according to the instructions contained in this manual; 2. The humidifier is free and clean; 3. The water supply...

  • Page 17

    Franco srl manual of use and maintenance ucp 17 4 - maintenance before undertaking any maintenance, disconnect the device from the electricity and water supply! Periodically check that the amount of water reaching the slinger is correct, if necessary adjust the flow regulator. Keep clean the disks, ...

  • Page 18

    Franco srl manual of use and maintenance ucp 18 4.4 changing the float disconnect the water supply. Remove the two screws from the lid by using a crosshead or “phillips” screwdriver. Remove the cover by pulling it, grabbing the grip between the thumb and the forefinger. Unscrew the plastic ring nut ...

  • Page 19

    Franco srl manual of use and maintenance ucp 19 4.6 positioning the nozzle after removing the spinning disk (par. 4.5), verify that the nozzle is positioned as shown in the following pictures. If the nozzle is not properly positioned, rotate the nozzle until the optimal position is reached. Always m...

  • Page 20

    Franco srl manual of use and maintenance ucp 20 5 – technical specifications 5.1 technical data general data ucp-1 ucp-3 ucp-1 ucp-3 atomization capacity lt/h 15 - 55 15 - 55 15 - 55 15 - 55 electrical supply 1 phase 3 phases + neutral 1 phase 3 phases + neutral degree of protection ip 56 56 56 56 w...

  • Page 21

    Franco srl manual of use and maintenance ucp 21 5.2 wiring all the wires used must be suitable to carry the current intensity (a) of the motor (par. 5.1). Terminal’s screws must be accurately tightened. Make sure that the electricity supply characteristics are exactly as shown in the table (par. 5.1...

  • Page 22

    Franco srl manual of use and maintenance ucp 22 5.3 spare parts it is highly recommended to use only original spare parts. Orders must be made by specifying what follows: - device model - reference of the piece (as indicated as follows) - quantity of items to be ordered - address of the client pos. ...

  • Page 23

    Franco srl manual of use and maintenance ucp 23 6 - problems and solutions before undertaking any maintenance, disconnect the device from the electricity and water supply! Problem cause solution the device does not start. The power supply is not plugged. Verify the electrical connection, or the func...

  • Page 24

    Franco srl manual of use and maintenance ucp 24 franco s.R.L. Headquarters and plant: via nazionale n.80 - 12010 - cervasca (cuneo) italy tel. (+39) 0171 611663 – fax (+39) 0171 612337 www.Francosrl.Com info@francosrl.Com for further information, requests or suggestions, please contact us at: custom...