Gakken Stirling engine Assemble And Operating Instructions - page 3
1
2 3
※Check the length
of screws with this
diagram.
One 7mm
bush
Fifteen 6mm
screws
A1
stand
A8
alcohol tray
A10
wick holder
A9
alcohol holder
Two
A2
body holders
A3
body holder
A5
safety lever
A6
arm
A7
arm part
A4
body holder
screw (6mm)
bush (7mm)
cross section of the safety
lever and the arm
※Check the size with this.
Full-scale
A1
stand
A5
safety lever
screw (6mm)
screw (6mm)
A6
arm
A7
arm part
screw (6mm)
screw (6mm)
bush (7mm)
bush (7mm)
A7
arm part
A6
arm
A5
safety lever
A6
A7
A5
bush
(7mm)
screw
(6mm)
screw
(6mm)
1
Assembling the Stand
Before Assembling the Kit
1.Understanding the right direction
2.How to Use Supplied Tools
●wrench
●small nut wrench
The direction is mentioned in the instructions. Check the right direction with the picture below.
The wrench can be used not only for
tightening a nut but also for tightening
screws as shown in the right figure.
It is used to fasten the connecting
rod at figure-18 on p.13.
●screwdriver (cross-headed tip)
The screwdriver can be used not
only for tightening a screw but also
for tightening a nut as shown in the
right figure.
※ Please note that shapes and length of materials may appear slightly different from pictures and illustrations in this booklet.
nut
How to use the
screwdriver
(cross-headed tip)
Turn.
the right part
(the front)
the left part
the hinder
part
Warning ★ Fire is used for the experiment. Use great caution to avoid
a burn and fire. Do not let a 15 or less-year-old child experiment alone.
1
Figure ー
Attach the A5 safety
lever to the A1 stand
with 6mm screws.
Then, attach the A6
arm to the A5 safety
lever, put in the bush
and fasten with the
A7 arm part.
1
Attach the arm to the safety lever.
the fore
part
How to use the wrench
when tightening screws
Put the thin part
of the wrench at
a slot of the screw
to fix.
Turn.
※ There may be more screws, washers, nuts
and bushes than actually used for spare.
PARTS
A
Parts to be used
1
2 3
※Check the length
of screws with this
diagram.
One 7mm
bush
Fifteen 6mm
screws
A1
stand
A8
alcohol tray
A10
wick holder
A9
alcohol holder
Two
A2
body holders
A3
body holder
A5
safety lever
A6
arm
A7
arm part
A4
body holder
screw (6mm)
bush (7mm)
cross section of the safety
lever and the arm
※Check the size with this.
Full-scale
A1
stand
A5
safety lever
screw (6mm)
screw (6mm)
A6
arm
A7
arm part
screw (6mm)
screw (6mm)
bush (7mm)
bush (7mm)
A7
arm part
A6
arm
A5
safety lever
A6
A7
A5
bush
(7mm)
screw
(6mm)
screw
(6mm)
1
Assembling the Stand
Before Assembling the Kit
1.Understanding the right direction
2.How to Use Supplied Tools
●wrench
●small nut wrench
The direction is mentioned in the instructions. Check the right direction with the picture below.
The wrench can be used not only for
tightening a nut but also for tightening
screws as shown in the right figure.
It is used to fasten the connecting
rod at figure-18 on p.13.
●screwdriver (cross-headed tip)
The screwdriver can be used not
only for tightening a screw but also
for tightening a nut as shown in the
right figure.
※ Please note that shapes and length of materials may appear slightly different from pictures and illustrations in this booklet.
nut
How to use the
screwdriver
(cross-headed tip)
Turn.
the right part
(the front)
the left part
the hinder
part
Warning ★ Fire is used for the experiment. Use great caution to avoid
a burn and fire. Do not let a 15 or less-year-old child experiment alone.
1
Figure ー
Attach the A5 safety
lever to the A1 stand
with 6mm screws.
Then, attach the A6
arm to the A5 safety
lever, put in the bush
and fasten with the
A7 arm part.
1
Attach the arm to the safety lever.
the fore
part
How to use the wrench
when tightening screws
Put the thin part
of the wrench at
a slot of the screw
to fix.
Turn.
※ There may be more screws, washers, nuts
and bushes than actually used for spare.
PARTS
A
Parts to be used
4
5