Gakken Stirling engine Assemble And Operating Instructions - page 5
the hinder part
※Check the length of screws
with these diagrams.
Four 6mm
screws
Two 26mm
screws
Two 30mm
screws
C5
15.5mm spring
C1
cylinder
C3
sliding base
C4
cylinder holder
Two
C2
cylinder supports
the fore part
the hinder
part
B6
rear wheel holders
B3
rear wheel
B1
body
screw (6mm)
screw (6mm)
screw (18mm)
B1
body
the hinder part
the fore part
B2
front wheels
nut (large 6mm)
washer
(7mm in diameter)
spring (9mm)
washer
(8mm in diameter)
bush (7mm)
washer (7mm in diameter)
screw (18mm)
B1
B5
screw
(18mm)
washers
(7mm in diameter)
washers
(8mm in diameter)
nut (large 6mm)
bush
(7mm)
screw (6mm) screw (18mm)
bush (7mm)
spring (9mm)
washer
(7mm in diameter)
nut
(large 6mm)
washer
(8mm in diameter)
B1
body
B1
body
B1
body
the fore part
the hinder part
C3
sliding base
C5
spring (15.5mm)
screw (6mm)
screw (6mm)
screw (6mm)
screw (6mm)
the fore part
the hinder part
C2
cylinder support
C2
cylinder support
the fore part
Four
C6
cylinder springs
C6
cylinder spring
screw (30mm)
screw (30mm)
C4
cylinder holder
C1
cylinder
screw (26mm)
C2
cylinder support
When the C1
cylinder comes
apart, set the
parts like this.
※When tightening the screws,
tighten four of them equally.
spring
(13mm)
C6
C6
screw (6mm)
C5
spring (15.5mm)
screw (30mm)
screw (26mm)
spring (13mm)
C6
cylinder spring
spring retaining bush
(6mm in diameter)
2.5mm in thickness
※Fasten the cylinder so
that it becomes parallel
to the body.
※Check the size with this.
Full-scale
※Check the size with this.
Full-scale
※Check the size with this.
Full-scale
Figure ー
Attach the front wheels assembled at
Figureー in the following order.
washer (7mm in diameter)
bush (7mm)
front wheel holder
washer (8mm in diameter)
spring (9mm)
washer (7mm in diameter)
nut (large 6mm)
6
3
Attaching the Cylinder to the Body
C
7
Figure ー
Overturn the body up
and attach the C3
sliding base to the
front wheels side
with the C5 spring.
7
Attach the C3 sliding base.
8
Figure ー
Fasten C2 cylinder
supports to the B1
body with 6mm
screws.
8
Attach the C2 cylinder supports.
9
Figure ー
Attach the C1
cylinder using the C6
cylinder springs.
Be sure to fasten the
C4 cylinder holder at
the back part with
30mm screws.
9
Attach the C1
cylinder.
cross section of the body
and the front wheels
5
Figure ー
Overturn the B1 body and
attach the rear wheels
assembled at Figure ー
with the B6 rear wheel
holders. Attach the 18mm
screw for the front wheels too.
5
4
4
Attach the rear wheels to the body.
6
Attach the front wheels
to the body.
spring
(9mm)
Warning ★ Fire is used for the experiment. Use great caution to avoid
a burn and fire. Do not let a 15 or less-year-old child experiment alone.
※ There may be more screws, washers, nuts
and bushes than actually used for spare.
PARTS
Parts to be used
8
9