Gnc and gns are trademarks of garmin ltd. Or its subsidiaries and may not be used without the express permission of garmin. (gns 430 shown) £ 190-00140-02, revision n february 2005 400 series installation manual gps 400, gnc tm 420 (a), and gns tm 430 (a).
Page a 400 series installation manual rev n p/n 190-00140-02 © copyright 1998 - 2005 garmin ltd. Or its subsidiaries all rights reserved except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for a...
400 series installation manual page i p/n 190-00140-02 rev n this manual is written for software version 4.03, and is not suitable for earlier software versions. Information in this document is subject to change without notice. Visit the garmin web site (www.Garmin.Com) for current updates and suppl...
Page ii 400 series installation manual rev n p/n 190-00140-02 table of contents 1. General description 1.1 introduction .........................................................................................................................................1-1 1.2 equipment description.................
400 series installation manual page iii p/n 190-00140-02 rev n list of figures figure 2-1. Gps antenna and unit installation considerations .............................................2-2 figure 3-1. Coaxial cable installation ...........................................................................
Page iv 400 series installation manual rev n p/n 190-00140-02 list of figures - continued figure f-32. King serial remote dme tuning interconnect ........................................................F-65 figure f-33. Parallel 2 of 5 dme tuning interconnect ...........................................
400 series installation manual page v p/n 190-00140-02 rev n 400 series hardware mod level history the following table identifies hardware modification (mod) levels for the gps 400, gnc 420 and gns 430. Mod levels are listed with the associated service bulletin number, service bulletin date, and the...
Page vi 400 series installation manual rev n p/n 190-00140-02 this page intentionally left blank.
400 series installation manual page 1-1 p/n 190-00140-02 rev n 1. General description 1.1 introduction this manual describes the physical, mechanical, and electrical characteristics and the installation requirements for the 400 series (gps 400, gnc 420, and gns 430) panel-mounted units. After instal...
Page 1-2 400 series installation manual rev n p/n 190-00140-02 1.3 technical specifications the conditions and tests required for tso approval of the 400 series are minimum performance standards. It is the responsibility of those desiring to install this article either on or within a specific type o...
400 series installation manual page 1-3 p/n 190-00140-02 rev n 1.3.2 general specifications operating temperature range -20 °c to +55°c. For more details see environmental qualification form. Humidity 95% non-condensing altitude range -1,500 ft to 50,000 ft input voltage range (gps 400) 11 to 33 v d...
Page 1-4 400 series installation manual rev n p/n 190-00140-02 1.3.4 com transceiver specifications (gnc 420 and gns 430 only) ** regulatory compliance tso-c37d class 4 & 6* (3 & 5 for “a” models), tso-c38d class c & e, jtso-2c37e (etso-2c37e for the gns 430a), jtso-2c38e (etso-2c38e for the gns 430...
400 series installation manual page 1-5 p/n 190-00140-02 rev n 1.3.5 vor specifications (gns 430 only) regulatory compliance tso c40c, jtso-2c40c (etso-2c40c for the gns 430a), rtca do-196, eurocae ed-22b receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course deviation ...
Page 1-6 400 series installation manual rev n p/n 190-00140-02 1.3.6 loc specifications (gns 430 only) regulatory compliance tso c36e, jtso-c36e (etso-c36e for the gns 430a), rtca do-195 class a, eurocae ed-46b receiver audio sensitivity at -103.5 dbm (s+n)/n shall not be less than 6 db. Course devi...
400 series installation manual page 1-7 p/n 190-00140-02 rev n 1.4 tso limitations a limitation exists pertaining to tso-c36e (localizer) and tso-c34e (glideslope). The main board lateral deviation (j4001 pin 21 main +left and j4001 pin 22 main +right) and vertical deviation (j4001 pin 27 main +up a...
Page 1-8 400 series installation manual rev n p/n 190-00140-02 fde is provided for oceanic and remote operations, non-precision approaches, en route and terminal phases of flight. Fde for non-oceanic flight phases adhere to the same missed alert probability, false alert probability, and failed exclu...
400 series installation manual page 2-1 p/n 190-00140-02 rev n 2. Installation 2.1 introduction careful planning and consideration of the suggestions in this section are required to achieve the desired performance and reliability from the 400 series unit. Any deviations from the installation instruc...
Page 2-2 400 series installation manual rev n p/n 190-00140-02 2.2.6 antenna limitations garmin’s ga 56 antennas are recommended for installations where the airspeed of the aircraft is subsonic. In such installations, ga 56—mod 1 or later—must be used. See the com, vor/loc, and glideslope antenna sp...
400 series installation manual page 2-3 p/n 190-00140-02 rev n 2.2.8 com, vor/loc, and glideslope antenna installation instructions install the com, vor/loc, and glideslope antennas according to the manufacturer’s recommendations. Avoid running other wires and coaxial cables near the vor/loc antenna...
Page 2-4 400 series installation manual rev n p/n 190-00140-02 hsi/cdi indicator or efis this device displays nav flag, left/right, to/from, glideslope flag, and up/down. The indicator(s) used in conjunction with the gns 430 vor/ils receivers shall be tso'd. Qualified gps antenna this antenna must b...
400 series installation manual page 3-1 p/n 190-00140-02 rev n 3. Installation procedure 3.1 unit and accessories the 400 series units are available under the following part numbers: 3.1.1 gns 430 (a) catalog p/n unit p/n gns 430a accessories (1) color operating voltage minimum xmit pwr 010-00139-00...
Page 3-2 400 series installation manual rev n p/n 190-00140-02 3.1.2 gnc 420 (a) catalog p/n unit p/n gnc 420a accessories (1) color operating voltage minimum xmit pwr 010-00173-00 011-00506-00 n n black 28 10 w 010-00173-01 011-00506-00 n y black 28 10 w 010-00173-10 011-00506-10 n n black 14 or 28...
400 series installation manual page 3-3 p/n 190-00140-02 rev n the following installation accessories are available: 1. Gps antenna options: • ga 56 antenna kit, without cable (mod 1 or later, garmin p/n 010-10040-01). This kit contains the following items: item garmin p/n qty ga 56 antenna sub-asse...
Page 3-4 400 series installation manual rev n p/n 190-00140-02 3.2 data base options item garmin p/n data card, world wide 010-10201-00 data card, americas 010-10201-01 data card, international 010-10201-02 3.3 miscellaneous options item garmin p/n connector, bnc, male, clamp 330-00087-00 low-loss a...
400 series installation manual page 3-5 p/n 190-00140-02 rev n caution do not use construction grade rtv sealant or sealants containing acetic acid. These sealants may damage the electrical connections to the antenna. Use of these type sealants may void the antenna warranty. 3.6 cable installation 1...
Page 3-6 400 series installation manual rev n p/n 190-00140-02 table 3-1. Pin contact part numbers 78 pin conn (p4001) 44 pin conn (p4006) 25 pin connector (p4002) shield ground connector connector type high density pin contact standard density socket contact .1” pitch card-edge wire gauge 22-28 awg...
400 series installation manual page 3-7 p/n 190-00140-02 rev n 3.7 rack installation 1. The back plate of the rack may optionally be removed for ease of mounting in the aircraft panel. To do so, remove the two #4-40 screws, tilt the back plate away from the tray, and then slide the back plate to the...
Page 3-8 400 series installation manual rev n p/n 190-00140-02 this page intentionally left blank.
400 series installation manual page 4-1 p/n 190-00140-02 rev n 4. System interconnects 4.1 pin function list 4.1.1 p4001 view of j4001 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49...
Page 4-2 400 series installation manual rev n p/n 190-00140-02 connector p4001, continued pin pin name i/o 37 altitude alarm audio hi (not implemented at time of publication) out 38 altitude alarm audio lo (not implemented at time of publication) out 39 lighting bus hi in 40 lighting bus lo in 41 gp...
400 series installation manual page 4-3 p/n 190-00140-02 rev n 4.1.2 p4002 (gnc 420 and gns 430 only) view of j4002 connector from back of unit 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 pin pin name i/o 1 reserved -- 2 reserved -- 3 reserved -- 4 com mic key in 5 intercom mic...
Page 4-4 400 series installation manual rev n p/n 190-00140-02 4.1.3 p4006 (gns 430 only) view of j4006 connector from back of unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 pin pin name i/o 1 vor/loc +to out 2 vor/loc ...
400 series installation manual page 4-5 p/n 190-00140-02 rev n 4.2 power, lighting, and antennas 4.2.1 power, lighting, and antennas function the section covers the power input requirements, lighting bus input, and antenna connections. 4.2.2 power, lighting, and antennas electrical characteristics 4...
Page 4-6 400 series installation manual rev n p/n 190-00140-02 4.2.3 power, lighting, and antennas configuration refer to section 5.2.6 for lighting configuration. 4.2.4 power, lighting, and antennas calibration and checkout refer to section 3.9 for the com antenna checkout. 4.2.5 power, lighting, a...
400 series installation manual page 4-7 p/n 190-00140-02 rev n 4.4 main indicator 4.4.1 main indicator function the main indicator displays both lateral and vertical deviation from selected course, to/from indications, lateral and vertical flags and superflags. The “cdi” key on the bezel of the gns ...
Page 4-8 400 series installation manual rev n p/n 190-00140-02 4.4.2.4 superflags pin name connector pin i/o main lateral superflag p4001 17 out main vertical superflag p4001 18 out the output supplies not less than 500 ma on a 28 volt system and 250 ma on a 14 volt system with the output voltage no...
400 series installation manual page 4-9 p/n 190-00140-02 rev n 4.5 annunciators/switches 4.5.1 annunciators/switches function note initial certification of the 400 series units was accomplished without use of any remote switches or annunciators, since the same switching and annunciation is available...
Page 4-10 400 series installation manual rev n p/n 190-00140-02 4.5.1.11 integrity annunciate the integrity annunciator illuminates when the gps receiver detects a position error, or is unable to calculate the integrity of the position. 4.5.1.11.1 ils/gps approach output sinks 500 ma when gps naviga...
400 series installation manual page 4-11 p/n 190-00140-02 rev n 4.6 serial data 4.6.1 serial data function 4.6.1.1 rs-232 the 400 series unit is capable of interfacing with other aviation instruments by transmitting rs-232 type 1 (often known as arnav format) and type 2 (often known as northstar for...
Page 4-12 400 series installation manual rev n p/n 190-00140-02 125 greenwich mean time (bcd) Ɣ Ɣ Ɣ Ɣ 147g magnetic variation Ɣ Ɣ Ɣ label # parameter name 1 2 3 4 251 distance to go Ɣ 251g distance to go Ɣ Ɣ Ɣ 252 time to go Ɣ Ɣ Ɣ Ɣ 260g date (bcd) Ɣ Ɣ Ɣ 261g gps discrete word 1 Ɣ Ɣ Ɣ 275g lrn statu...
400 series installation manual page 4-13 p/n 190-00140-02 rev n 4.6.2 serial data electrical characteristics 4.6.2.1 rs-232 pin name connector pin i/o gps rs 232 out 1 p4001 56 out gps rs 232 in 1 p4001 57 in gps rs 232 out 2 p4001 58 out gps rs 232 in 2 p4001 59 in gps rs 232 out 3 p4001 41 out gps...
Page 4-14 400 series installation manual rev n p/n 190-00140-02 4.7 com/vor/ils audio (gnc 420 and gns 430 only) 4.7.1 com/vor/ils audio function and emergency mode activation of com mic key enables com mic audio and causes the transceiver to transmit. 500 Ω com audio and 500Ω vor/ils audio are 100 ...
400 series installation manual page 4-15 p/n 190-00140-02 rev n 4.7.2.3 com audio, vor/ils audio pin name connector pin i/o 500 Ω com audio hi p4002 7 out 500 Ω com audio lo p4002 19 out 500 Ω vor/ils audio hi p4006 16 out 500 Ω vor/ils audio lo p4006 17 out 500 Ω com audio and 500Ω vor/ils audio ea...
Page 4-16 400 series installation manual rev n p/n 190-00140-02 4.8 vor/ils indicator (gns 430 only) 4.8.1 vor/ils indicator function note because the gns 430 includes a “cdi” button that performs switching between gps and vor/ils on a remote indicator, it is seldom necessary to use these outputs to...
400 series installation manual page 4-17 p/n 190-00140-02 rev n 4.8.2.4 flag pin name connector pin i/o vor/loc +flag p4006 3 out vor/loc -flag (vor/loc common) p4006 4 out glideslope +flag p4006 30 out glideslope +down/-flag (glideslope common) p4006 31 out the flag output is capable of driving up ...
Page 4-18 400 series installation manual rev n p/n 190-00140-02 4.9 rmi/obi 4.9.1 rmi/obi function the main obi output provides bearing information from the active waypoint for bendix/king serial obi devices based upon the 400 series unit’s gps navigation. For the gns 430, the main obi output may be...
400 series installation manual page 4-19 p/n 190-00140-02 rev n 4.10 dme tuning (gns 430 only) 4.10.1 dme tuning function the gns 430 can channel a dme based on the tuned vloc frequency. The gns 430 outputs 2 of 5, bcd or slip parallel dme and king serial dme channeling format. When dme common is he...
Page 4-20 400 series installation manual rev n p/n 190-00140-02 4.10.3 dme tuning configuration refer to section 5.2.12 for the dme tuning configuration. 4.10.4 dme tuning calibration and checkout none. 4.10.5 dme tuning interconnect refer to figure f-31 on page f-63 for the king serial panel dme tu...
400 series installation manual page 5-1 p/n 190-00140-02 rev n 5. Post installation configuration & checkout procedure 5.1 configuration mode operations with power applied to the aviation rack and the 400 series unit turned off, press and hold the ent key and turn the unit on. Release the ent key wh...
Page 5-2 400 series installation manual rev n p/n 190-00140-02 data in 1, data in 2 selection description off no unit connected to this arinc 429 input airdata altitude, temperature, and speed information from the following airdata systems: b & d 2600, 2601, 2800, 90004-003, bendix/king kad 280/480,...
400 series installation manual page 5-3 p/n 190-00140-02 rev n data out selection description off no unit(s) connected to arinc 429 output arinc 429 standard arinc 429 output data (non-gama). Gama 429 arinc 429 data as defined by the general aviation manufacturers’ association (gama) general aviatio...
Page 5-4 400 series installation manual rev n p/n 190-00140-02 channel inputs selection description off no unit(s) connected to input of this channel. Arnav/ei-fuel serial fuel flow information from the following units: arnav fc-10, ft-10 electronics international fp-5l crossfill serial transfer of ...
400 series installation manual page 5-5 p/n 190-00140-02 rev n 5.2.3 main inputs 1 page select the main inputs 1 page (see figure 5-3). This page (along with the main inputs 2 page) allows you to monitor the data on arinc 429, rs-232 and other electrical inputs. This is used for verifying electrical...
Page 5-6 400 series installation manual rev n p/n 190-00140-02 5.2.6 main lighting page select the main lighting page (see figure 5-6). This page allows you to set display parameters that affect the display backlight and key lighting brightness. The display and key lighting characteristics are adjus...
400 series installation manual page 5-7 p/n 190-00140-02 rev n offset adjusts the lighting level up or down for any given input level. This field has a range of 0 (zero) to 99, and is set to 50 at the factory. This may also be used to match lighting curves with other equipment in the panel. Photo tr...
Page 5-8 400 series installation manual rev n p/n 190-00140-02 external switch state selection verify that: rmt cdi the box is filled in while a remote cdi source select switch is pressed. Rmt obs the box is filled in while a remote obs switch is pressed. 5.2.9 main discrete outputs page select the ...
400 series installation manual page 5-9 p/n 190-00140-02 rev n nav flag (lat/vert) selection verify that: hidden the lat/vert flag is hidden. In view the lat/vert flag is in view. To-from selection verify that: from the from flag is in view. Hidden the to/from flag is hidden. To the to flag is in vi...
Page 5-10 400 series installation manual rev n p/n 190-00140-02 obi source (gns 430 only) selection description always gps the main king serial obi outputs are always gps. This is useful if it is desired to switch a bendix/king ki 229 or kni 582 rmi pointer independently from the gns 430 cdi button....
400 series installation manual page 5-11 p/n 190-00140-02 rev n 5.2.11 com setup page (gnc 420 and gns 430 only) select the com setup page (see figure 5-13). These values are set at the factory and seldom require calibration. Freq selects a vhf communication frequency. For purposes of setting the sq...
Page 5-12 400 series installation manual rev n p/n 190-00140-02 5.2.12 vor discrete inputs page (gns 430 only) select the vor discrete inputs page (see figure 5- 14). This page allows you to verify the operation of an external vloc transfer switch that may be present in the installation. Selection v...
400 series installation manual page 5-13 p/n 190-00140-02 rev n to-fr selection verify that: from the from flag is in view. Hide the to/from flag is hidden. To the to flag is in view. Selected course select 150° on the cdi/hsi that is connected to the 400 series vor/loc/gs obs inputs. The selected c...
Page 5-14 400 series installation manual rev n p/n 190-00140-02 dme mode selection description directed freq 1 if the gns 430 is connected to a multi-channel arinc 429 dme, channel 1 of that dme is tuned. “directed freq 1” should be selected if a single- channel arinc 429 dme is tuned. Directed freq...
400 series installation manual page 5-15 p/n 190-00140-02 rev n 5.2.18 traffic page (only if 400 series unit configured for bfg skywatch or ryan tcad interfaces) select the traffic page (see figure 5-20). This page shows the bfg skywatch or ryan tcad modes of operation and current traffic situation....
Page 5-16 400 series installation manual rev n p/n 190-00140-02 5.2.21 monitoring the data link the data link is monitored on the data link page. There are four main page groups in the 400 series software version 2.25 or higher: nav, wpt, aux, and nrst (see the 400 series unit pilot’s guide for deta...
400 series installation manual page 5-17 p/n 190-00140-02 rev n 5.3 additional ground tests 5.3.1 connector engagement test 1. Turn on the 400 series unit, and turn on the avionics master switch (if applicable). 2. Place the 400 series unit in the rack and engage the pawl mechanism. 3. Turn the alle...
Page 5-18 400 series installation manual rev n p/n 190-00140-02 5.3.4 deviation & flags check 5.3.4.1 analog deviation & flags the analog deviation (left/right and up/down), to/from, and flag (lateral and vertical) outputs to a cdi or hsi should be verified in flight with potential sources of electr...
400 series installation manual page 5-19 p/n 190-00140-02 rev n 5.3.7 vhf com check (gnc 420 and gns 430 only) a flight test is recommended after the installation is complete to ensure satisfactory performance. To check the communications transceiver, maintain an appropriate altitude and contact a g...
Page 5-20 400 series installation manual rev n p/n 190-00140-02 this page intentionally left blank.
400 series installation manual page a-1 p/n 190-00140-02 rev n appendix a. Certification documents a.1 continued airworthiness this section provides assistance to the installing agency in preparing instructions for continued airworthiness (ica) in response to bulletin number hbaw 98-18, “checklist f...
Page a-2 400 series installation manual rev n p/n 190-00140-02 6. Troubleshooting information refer to the 400 series maintenance manual. 7. Removal and replacement information refer to section 3.8 of this manual. If the unit is removed and reinstalled, a functional check of the equipment should be ...
400 series installation manual page a-3 p/n 190-00140-02 rev n a.2 environmental qualification form—gns 430 nomenclature: gns 430 airborne gps/vor/ils/com system type/model/part no.: 010-00139-(), which includes 011-00280-00 tso/jtso compliance: tso-c129a class a (1) (gps) tso-c37d class 4 & 6, jtso...
Page a-4 400 series installation manual rev n p/n 190-00140-02 a.3 environmental qualification form—gnc 420 nomenclature: gnc 420 airborne gps/com system type/model/part no.: 010-00173-(), which includes 011-00506-00 tso/jtso compliance: tso-c129a class a (1) (gps) tso-c37d class 4 & 6, jtso-2c37e (...
400 series installation manual page a-5 p/n 190-00140-02 rev n a.4 environmental qualification form—gps 400 nomenclature: gps 400 airborne gps system type/model/part no.: 010-00171-(), which includes 011-00504-00 tso/jtso compliance: tso-c129a class a (1) (gps) manufacturer’s specification and/or ot...
Page a-6 400 series installation manual rev n p/n 190-00140-02 a.5 environmental qualification form—ga 56 nomenclature: ga 56, gps aviation antenna type/model/part no.: 011-00134-00 (stud mount) 011-00147-00 (flange mount) tso compliance: c129 class a (1) manufacturer’s specification and/or other ap...
400 series installation manual page b-1 p/n 190-00140-02 rev n appendix b. Stc permission consistent with n8110.69 or order 8110.4, aviation authority approved installers are hereby granted permission to use stc’s #sa00705wi (gns 430 and gns 430a), #sa00801wi (gnc 420 and gnc 420a), and #sa00800wi (...
Page b-2 400 series installation manual rev n p/n 190-00140-02.
400 series installation manual page b-3 p/n 190-00140-02 rev n.
Page b-4 400 series installation manual rev n p/n 190-00140-02.
400 series installation manual page b-5 p/n 190-00140-02 rev n.
Page b-6 400 series installation manual rev n p/n 190-00140-02.
400 series installation manual page b-7 p/n 190-00140-02 rev n.
Page b-8 400 series installation manual rev n p/n 190-00140-02.
400 series installation manual page b-9 p/n 190-00140-02 rev n.
Page b-10 400 series installation manual rev n p/n 190-00140-02 this page intentionally left blank..
400 series installation manual page c-1 p/n 190-00140-02 rev n appendix c. 400 series rs-232 aviation data format c.1 electrical interface the output signals shall be compatible with rs-232c. Data shall be generated at 9600 baud with a word length of 8 bits, one stop bit, and no parity. C.2 general ...
Page c-2 400 series installation manual rev n p/n 190-00140-02 the following table describes the type 1 output sentence item designator (id) and item data (dddd) fields. If data for these sentences is invalid or unavailable, dashes ("-") are used to fill in all non-blank character positions. * the l...
400 series installation manual page c-3 p/n 190-00140-02 rev n c.4 output sentence type 2 the 400 series type 2 output sentence shall have the following general format: id - item designator (3 ascii characters) seq - sequence number (1 binary byte) wpt - waypoint identifier (5 ascii characters) lat ...
Page c-4 400 series installation manual rev n p/n 190-00140-02 the following table describes the type 2 output sentence item designator (id), sequence number (seq), waypoint identifier (wpt), waypoint latitude (lat), waypoint longitude (lon), and magnetic variation at waypoint (mvar) fields. Field b...
400 series installation manual page d-1 p/n 190-00140-02 rev n appendix d. 400 series rs-232 fuel/air data input format d.1 electrical interface the input signals shall be compatible with rs-232c. Data shall be input at 9600 baud with a word length of 8 bits, one stop bit, and no parity. One message...
Page d-2 400 series installation manual rev n p/n 190-00140-02 d.4 shadin fuel flow sentence the garmin 400 series units shall be capable of receiving the following 55-byte message from the shadin fuel flow indicator: k0543.20100.00040.00060.00123.40045.40078.0123 where: start-transmit character (0x...
400 series installation manual page d-3 p/n 190-00140-02 rev n d.6 shadin fuel/airdata computer sentence the garmin 400 series units shall be capable of receiving the following message strings from the shadin fuel/airdata or airdata computer: d.6.1 shadin “z” format za012 "za" (ascii characters); "0...
Page d-4 400 series installation manual rev n p/n 190-00140-02 d.6.2 shadin “g” format ga012 "ga" (ascii characters); "012" represents indicated air speed (knots) gb345 "gb" (ascii characters); "345" represents true air speed (knots) gc678 "gc" (ascii characters); "678" represents mach speed (thousa...
400 series installation manual page d-5 p/n 190-00140-02 rev n d.6.3 shadin “s” format sa012 "sa" (ascii characters); "012" represents indicated air speed (knots) sb345 "sb" (ascii characters); "345" represents true air speed (knots) sc678 "sc" (ascii characters); "678" represents mach speed (thousa...
Page d-6 400 series installation manual rev n p/n 190-00140-02 note: checksum is calculated by adding each byte in the message (including all characters from up to and including the error log/reason indicator), such that carries are discarded to give a one byte result. The ascii-coded decimal repres...
400 series installation manual page e-1 p/n 190-00140-02 rev n appendix e. 400 series lru interface overview the following tables provide a quick overview of some of the equipment that can be interfaced with the garmin 400 series units. This is not a complete listing however; it only represents thos...
Page e-2 400 series installation manual rev n p/n 190-00140-02 function bendix/king collins efis efis 40/50 efis-84 displays sg 465 dpu-84 function sandel ehsi sn 3308 function bendix/king collins honeywell litef litton iru/ahrs kau 461 ahc 85e laseref ltr 81 ltn 90-100 hg 1075 ab ltn-91 hg 1095 ab ...
400 series installation manual page f-1 p/n 190-00140-02 rev. N appendix f. Drawings and interconnects f.1 introduction this section contains installation drawings to aid in the installation of a 400 series unit. Additional information and notes included on the drawings can be used as reference info...
Page f-2 400 series installation manual rev. N p/n 190-00140-02 figure f-29—vor/ils indicator interconnect figure f-30—rmi/obi interconnect figure f-31—king serial panel dme tuning interconnect figure f-32—king serial remote dme tuning interconnect figure f-33—parallel 2 of 5 dme tuning interconnect...
400 series installation manual page f-3 (page f-4 blank) p/n 190-00140-02 rev n figure f-1. Ga 56 antenna installation draw ing.
400 series installation manual page f-5 (page f-6 blank) p/n 190-00140-02 rev n figure f-2. Gns 430 mounting rack dimensions.
400 series installation manual page f-7 (page f-8 blank) p/n 190-00140-02 rev n figure f-3. Gnc 420 mounting rack dimensions.
400 series installation manual page f-9 (page f-10 blank) p/n 190-00140-02 rev n figure f-4. Gps 400 mounting rack dimensions.
400 series installation manual page f-11 (page f-12 blank) p/n 190-00140-02 rev n figure f-5. Gns 430 mounting rack installation.
400 series installation manual page f-13 (page f-14 blank) p/n 190-00140-02 rev n figure f-6. Gnc 420 mounting rack installation.
400 series installation manual page f-15 (page f-16 blank) p/n 190-00140-02 rev n figure f-7. Gps 400 mounting rack installation.
400 series installation manual page f-17 (page f-18 blank) p/n 190-00140-02 rev n figure f-8. 400 series recommended panel cutout dimensions.
400 series installation manual page f-19 (page f-20 blank) p/n 190-00140-02 rev n figure f-9. 400 series sy stem interface diagram.
400 series installation manual page f-21 (page f-22 blank) p/n 190-00140-02 rev n figure f-10. Gns 430 ty pical installation.
400 series installation manual page f-23 (page f-24 blank) p/n 190-00140-02 rev n figure f-11. Gnc 420 ty pical installation.
400 series installation manual page f-25 (page f-26 blank) p/n 190-00140-02 rev n figure f-12. Gps 400 ty pical installation.
400 series installation manual page f-27 (page f-28 blank) p/n 190-00140-02 rev n figure f-13. Pow er, lighting, and antenna interconnect.
400 series installation manual page f-29 (page f-30 blank) p/n 190-00140-02 rev n figure f-14. Altimeter interconnect.
400 series installation manual page f-31 (page f-32 blank) p/n 190-00140-02 rev n figure f-15. Main indicator interconnect.
400 series installation manual page f-33 (page f-34 blank) p/n 190-00140-02 rev n figure f-16. Ki 209a main indicator interconnect.
400 series installation manual page f-35 (page f-36 blank) p/n 190-00140-02 rev n figure f-17. Ki 208a main indicator interconnect.
400 series installation manual page f-37 (page f-38 blank) p/n 190-00140-02 rev n figure f-18. Annunciators/sw itches interconnect.
400 series installation manual page f-39 (page f-40 blank) p/n 190-00140-02 rev n figure f-19. Rs-232 serial data interconnect.
400 series installation manual page f-41 (page f-42 blank) p/n 190-00140-02 rev n figure f-20. Arinc 429 efis interconnect.
400 series installation manual page f-43 (page f-44 blank) p/n 190-00140-02 rev n figure f-21. Arinc 429 sandel ehsi interconnect (1 400 series unit, 1 sandel sn3308).
400 series installation manual page f-45 (page f-46 blank) p/n 190-00140-02 rev n figure f-22. Arinc 429 sandel ehsi interconnect (2 gns 430, 1 sandel sn3308).
400 series installation manual page f-47 (page f-48 blank) p/n 190-00140-02 rev n figure f-23. Arinc 429 sandel ehsi interconnect (2 gns 430, 2 sandel sn3308).
400 series installation manual page f-49 (page f-50 blank) p/n 190-00140-02 rev n figure f-24. Arinc 429/rs-232 air data/iru/ahrs interconnect.
400 series installation manual page f-51 (page f-52 blank) p/n 190-00140-02 rev n figure f-25. Arinc 429 flight control interconnect.
400 series installation manual page f-53 (page f-54 blank) p/n 190-00140-02 rev n figure f-26. Traffic advisory sy stem interconnect.
400 series installation manual page f-55 (page f-56 blank) p/n 190-00140-02 rev n figure f-27. Weather and terrain interconnect.
400 series installation manual page f-57 (page f-58 blank) p/n 190-00140-02 rev n figure f-28. Audio panel interconnect.
400 series installation manual page f-59 (page f-60 blank) p/n 190-00140-02 rev n figure f-29. Vor/ils indicator interconnect.
400 series installation manual page f-61 (page f-62 blank) p/n 190-00140-02 rev n figure f-30. Rmi/obi interconnect.
400 series installation manual page f-63 (page f-64 blank) p/n 190-00140-02 rev n figure f-31. King serial panel dme tuning interconnect.
400 series installation manual page f-65 (page f-66 blank) p/n 190-00140-02 rev n figure f-32. King serial remote dme tuning interconnect.
400 series installation manual page f-67 (page f-68 blank) p/n 190-00140-02 rev n figure f-33. Parallel 2 of 5 dme tuning interconnect.
400 series installation manual page f-69 (page f-70 blank) p/n 190-00140-02 rev n figure f-34. Parallel bcd/slip code dme tuning interconnect.