- DL manuals
- Haier
- Other
- H2SM- - annexe 25
- Operation Manual
Haier H2SM- - annexe 25 Operation Manual
Summary of H2SM- - annexe 25
Page 1
Split type room air conditioner operation manual please read this operation manual before using the air conditioner. No. H2sm-(9+9)h03/r2(db) h2sm-(9+12)h03/r2(db).
Page 2
Before disposing an old air conditioner that goes out of use, please make sure it's inop- erative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require speciali- zed waste disposal. The...
Page 3
Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver. Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit. The refrigerating circuit is l...
Page 4
Cautions strict enforcement safety instruction installation warning please read the following safety instructions carefully prior to use. The instructions are classified into two levels, warning and caution according to the seriousness of possible risks and damages as follows. Compliance to the inst...
Page 5
Cautions warning when abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. Off use an exclusive power source with a circuit breaker enforcement connect power supply cord to the outlet completely use the proper voltage do not use power supply cord in a ...
Page 6
Parts and functions indoor unit 5 outdoor unit inlet grille air filter vertical flap power indicator timer mode indicator operation mode indicator remote signal receiver emergency switch(manual) test running switch(manual) use remote controller to adjust up and down air flow. (don't adjust it manual...
Page 7
16. Signal sending display 17. Power/soft display 18. Left/right air flow display 19. Temp display remote controller: to display the temp. Setting. 20. Timer off display 21. Clock display 22. Fan button used to select fan speed: low,med, hi, auto 23. On/off button used for unit start and stop. 24. S...
Page 8
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key. Parts and functions clock set when unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follow...
Page 9
Press health button, the health function stops. The pilot light of healthy process on the display board is extinguished. Brief introduction to health operation the anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air ...
Page 10
Operation auto operation remote controller about auto operation under the mode of auto operation, air conditioner will automatically select cool or heat operation according to room temperature. 1. Unit start link with electronic power. Press on/off on the remote controller, unit starts. The liquid c...
Page 11
Operation cool operation remote controller 1. Unit start link with electronic power. Press on/off on the remote controller, unit starts. The liquid crystal will display the working state of last time (except timer, sleep, power/soft and health airflow). 2.Select operation mode press fan button. For ...
Page 12
Operation dry operation remote controller 1. Unit start link with electronic power. Press on/off on the remote controller, unit starts. The liquid crystal will display the working state of last time (except timer, sleep, power/soft and health airflow). 2.Select operation mode press fan button. For e...
Page 13
Operation fan operation remote controller 1. Unit start link with electronic power. Press on/off on the remote controller, unit starts. The liquid crystal will display the working state of last time (except timer, sleep, power/soft and health airflow). 2.Select operation mode press fan button. For e...
Page 14
Operation heat operation remote controller 1. Unit start link with electronic power. Press on/off on the remote controller, unit starts. The liquid crystal will display the working state of last time (except timer, sleep, power/soft and health airflow). 2.Select operation mode press fan button. For ...
Page 15
Operation 14 (5)air flow direction adjustment after operation mode is selected, vertical flap will open automatically according to the mode. Referring to the fig. Cool heat cool heat about 10 o about 60 o about 10 o about 45 o about 60 o better set a temp. Difference of 3-5 o c between indoor and ou...
Page 16
Before going to bed, you can simply press the sleep button and unit will operate in sleep mode and bring you a sound sleep. Use of sleep function after the unit starts, set the operation status, then press sleep button before which the clock must be adjusted and time being set. Operation mode 1. In ...
Page 17
Remote controller timer on/off operation operation hints: after replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use timer mode next time,just press set button after mode selecting if time setting is the same as previous ...
Page 18
Remote controller timer on-off operation operation just press timer button several times until timer mode disappears. According to the time setting sequence of timer on or timer off, either start-stop or stop-start can be achieved. Set clock correctly before starting timer operation. 1. After unit s...
Page 19
Power/soft operation power operation power operation soft operation when you need rapid heating or cooling, you can use this funciton. You can use this function when silence is needed for rest or reading. Selecting of power operation press power/soft button. Every time the button is pressed,display ...
Page 20
When the remote controller is manipulated, it gets the system back to the normal operation mode. Emergency and test operation operation when machine is running in emergency, the set value of temperature and wind speed couldn't be altered; meanwhile, it can't operate for dehumidifying or under timing...
Page 21
For smart use of the air conditioner setting of proper room temperature proper temperature during cooling operation, prevent the penetration of direct sunlight with curtain or blind. Close doors and windows during operation if the unit is not to be used for a long time, turn off the power supply mai...
Page 22
For smart use of the air conditioner warning air filter cleaning open the inlet grille by pulling it upward. Remove the filter. Clean the filter. Attach the filter. Close the inlet grille. Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward....
Page 23
Replacement of air purifying filter 1.Open the lnlet grille 2.Detach the standard air filter 3.Detach the air purifying filter 4.Attach new air purifying filter 5.Attach the standard air filter as its front side faces to the front operating without standard air filter may cause troubles with the mac...
Page 24
To keep your air conditioner in good condition after season. Operate in cooling mode for 2-3 hours. Put off the power supply cord. Take out the batteries from the wireless remote controller. Cleaning the body. To prevent breeding mold or bad smell, be sure to operate at the designated temperature or...
Page 25
Before setting in high season cleaning the standard air filter. Connecting the earthing cable. Do not block the air inlet or outlet. Plug-in caution caution after brush away dust at the plug, insert the plug of the power supply cord into the outlet completely.In case of suing exclusive circuit break...
Page 26
Is the air filter dirty? Normally it should be cleaned every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(use curtain) are there too muc...