- DL manuals
- Haier
- Other
- H2SM- - annexe 25
- Operation Manual
Haier H2SM- - annexe 25 Operation Manual
Summary of H2SM- - annexe 25
Page 1
No.001056 split type room air conditioner operation manual please read this operation manual before using the air conditioner hsu- ( 9 +9) rh03/r2(db) hsu- (9+ 12 ) rh03/r2(db).
Page 2
Before disposing an old air conditioner that goes out of use, please make sure it's inop- erative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require speciali- zed waste disposal. The...
Page 3
3. If the fuse of indoor unit on pc board is broken,please change it with the type of t. 3.15a/ 250v. If the fuse of outdoor unit is broken,change it with the type of t.25a/250v do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inle...
Page 4
Cautions strict enforcement safety instruction installation warning please read the following safety instructions carefully prior to use. The instructions are classified into two levels, warning and caution according to the seriousness of possible risks and damages as follows. Compliance to the inst...
Page 5
Cautions warning when abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. Off use an exclusive power source with a circuit breaker enforcement connect power supply cord to the outlet completely use the proper voltage do not use power supply cord in a ...
Page 6
Outdoor unit 1 2 3 4 parts and functions indoor unit 5 display board inlet anion generator vertical flap (use remote controller to adjust up and down air flow. Don't adjust it manually) horizontal louver air filter inlet grille (inside) (adjust left and right air flow) (inside) outlet connecting pip...
Page 7
Parts and functions used to set healthy operation. 9. Health button used for unit start and stop. 10. On/off button 11. Timer on display 12. Fan speed display low hi med auto 13. Lock display 14. Swing up/down display 15. Sleep display 16. Health display used to select your desired temperature. Oper...
Page 8
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key. Parts and functions clock set when unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follow...
Page 9
Operation remote controller 8 power/soft 2.Health function air conditioner starts health anion function operation. For twice press, disappears,the operation stops. Brief introduction to health anion fuction the anion generator in the air conditioner can generate a lot of anion effectively balance th...
Page 10
Auto operation operation remote controller 9 power/soft about auto operation under the mode of auto operation, air conditioner will automatically select cool or heat operation according to room temperature. 5.Unit stop press on/off button, the unit stops. 1. Unit start press on/off on the remote con...
Page 11
Cool operation remote controller 2.Select operation mode press fan button. For each press, fan speed changes as follows: press mode button. For each press, operation mode changes as follows: remote controller: remote controller: then select cool operation press temp. Button every time the button is ...
Page 12
2.Select operation mode press fan button. For each press, fan speed changes as follows: press mode button. For each press, operation mode changes as follows: remote controller: remote controller: then select dry operation press temp. Button every time the button is pressed, temp.Setting increase 1 o...
Page 13
Fan operation 2.Select operation mode press fan button. For each press, fan speed changes as follows: press mode button. For each press, operation mode changes as follows: remote controller: remote controller: then select fan operation 3.Fan speed selection 4.Unit stop about fan operation in fan ope...
Page 14
Operation 2.Select operation mode press fan button. For each press, fan speed changes as follows: press mode button. For each press, operation mode changes as follows: remote controller: remote controller: then select heat operation press temp. Button every time the button is pressed, temp.Setting i...
Page 15
2.Up and down air flow direction vertical flap pos.1 pos.1 pos.2 pos.3 pos.4 pos.6 pos.5 pos.4 pos.3 pos.2 pos.1 pos.6 pos.1 pos.2 pos.3 pos.4 pos.5 pos.6 pos.2 pos.3 pos.4 pos.5 pos.6 (auto swing) for each press of button, air flow direction on remote controller displays as follows according to dif...
Page 16
If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change. 5.Set the wind speed change when sleeping before going to bed, you can simply press the sleep button and unit will operate in sleep mode and bring you a sound...
Page 17
Power/soft remote controller timer on/off operation operation hints: after replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use timer mode next time, just press set button after mode selecting if time setting is the same ...
Page 18
Remote controller timer on-off operation operation just press timer button several times until timer de disappears. According to the time setting sequence of timer on or timer off, either start-stop or stop-start can be achieved. Set clock correctly before starting timer operation. 1. After unit sta...
Page 19
Power/soft operation power operation power operation soft operation when you need rapid heating or cooling, you can use this function. You can use this function when silence is needed for rest or reading. Selecting of power operation press power/soft button. Every time the button is pressed,display ...
Page 20
Remote controller power/soft fresh 1.Press on/off to starting operation the liquid crystal will display the working state of last time (except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions. 2.The setting of health airflow function 1).Press the button of health ...
Page 21
When the remote controller is manipulated, it gets the system back to the normal operation mode. Emergency and test operation operation emergency operation: use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed,the" pi "sound is heard...
Page 22
For smart use of the air conditioner setting of proper room temperature close doors and windows during operation if the unit is not to be used for a long time, turn off the power supply main switch. Use the timer effectively use the louvers effectively do not block the air inlet or outlet maintenanc...
Page 23
For smart use of the air conditioner warning air filter cleaning open the inlet grille by pulling it upward. Remove the filter. Clean the filter. Attach the filter. Close the inlet grille. Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward....
Page 24
23 maintenance detach old air purifying filter replancement of air purifying filter 1.Open the lnlet grille 2.Detach the standard air filter 3.Detach old air purifying filter 4.Attach old air purifying filter 5.Attach the standard air filter (necessary installation) 6.Close the inlet grille close th...
Page 25
To keep your air conditioner in good condition after season. Operate in cooling mode for 2-3 hours. Put off the power supply cord. Take out the batteries from the wireless remote controller. Cleaning the body. To prevent breeding mold or bad smell, be sure to operate at the designated temperature or...
Page 26
Before setting in high season cleaning the standard air filter. Connecting the earthing cable. Do not block the air inlet or outlet. Plug-in caution caution after brush away dust at the plug, insert the plug of the power supply cord into the outlet completely.In case of suing exclusive circuit break...
Page 27
Is the air filter dirty? Normally it should be cleaned every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(use curtain) are there too muc...