Icom VE-PG2 Installation Manual - page 3
RoIP GATEWAY
Installation guide w
VE-PG2
Step1: Installation guide q
Step2: Installation guide w
1. Connects transceivers and LAN to the VE-PG2
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
1
2
3
4
5
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
q
w
t
y
e
To the [LAN] port
To the [TRX1] port
HUB
(192.168.0.2)
The [TRX1] port number: 21500
Connect the transceiver’s microphone connector and speaker jack.
NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.
Repeater’s rear panel
OPC-2074
ACC connector
[Area A]
[Area B]
Transceiver B
channel 2
Connect an Ethernet cable
Connect an Ethernet cable
VE-PG2
To the [TRX1] port
(192.168.0.3)
The [TRX1] port number: 21500
VE-PG2
To the [LAN] port
Connect the transceiver’s microphone connector and speaker jack.
Transceiver A
channel 2
Transceiver C
channel 10
Transceiver D
channel 10
NOTE: First, connect the transceiver
to the VE-PG2 using the optional
OPC-2073. Then turn ON the power
to the transceiver and the VE-PG2.
NOTE: First, connect the transceiver
to the VE-PG2 using the optional
OPC-2073. Then turn ON the power
to the transceiver and the VE-PG2.
Connect to the transceiver A’s speaker jack.
Connect to the transceiver C’s speaker jack.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable may damage the VE-PG2,
transceivers or repeaters.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable may damage the VE-PG2,
transceivers or repeaters.
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
Connect the optional OPC-2074 to
[TRX1], [TRX2] or [TRX3] only.
GROUND
GROUND
Turn the transceivers’ power ON,
and then set the transceiver A
volume to the 12 o’clock position.
Turn the transceivers’ power ON,
and then set the transceiver C
volume to the 12 o’clock position.
If you connect the VE-PG2 to an
IP network, instead of the hub as
shown in this illustration, you can
communicate anywhere through
the IP network.
r
Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.
*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.
• A static (fixed) IP address must be set to the VE-PG2, and connects as figure below. (Refer to the Installation guide q for
details.)
• For the Unicast mode, after making the connections as illustrated below, set the VE-PG2 as described in the page to the
right.
• Refer to the Installation guide q for details of the Multicast mode and the Unicast modes.
• Connect the VE-PG2 according to steps q – y in the illustration below.
Bridge mode setting
2 Sets the VE-PG2 to the Bridge mode (Unicast mode)
1. P comm nication mode setting setting
P comm nication mode setting setting
P comm nication mode setting setting
setting
setting
2. P net or connection ranceiver 1 ( 1) setting
P net or connection ranceiver 1 ( 1) setting
P net or connection ranceiver 1 ( 1) setting
ranceiver 1 ( 1) setting
ranceiver 1 ( 1) setting
ranceiver 1 ( 1) setting
ranceiver 1 ( 1) setting
setting
setting
Set transceivers A and C AF volume to the 12 o clock
clock
clock
position.
3. ransceiver setting
4. Ho to comm nicate
1
1
1
While holding down transceiver D s [PTT] of Area B,
speak into the microphone at your normal voice level
to reply to transceiver B in Area A.
Release transceiver D s [PTT] to receive.
While holding down transceiver B s [PTT] in Area A,
speak into the microphone at your normal voice level
to call transceiver D in Area B.
Release transceiver B s [PTT] to receive.
1
2
Bridge mode setting
Turn transceivers B and D power ON, and select the
same operating channel as transceivers A and C.
• Set the same channel for all the transceivers, to
communicate with transceivers A and C.
See the transceiver s instruction manual when
setting the channel, if necessary.
(Example) I n t h e i l l u s t ra t i o n t o t h e l e f t , s e t
transceiver A and B (Area A) to channel
2, and transceiver C and D (Area B) to
channel 10.
2
This setting example refers to the connections in the far top
left illustration.
This setting example refers to the connections in the far top
left illustration.
2. IP network connection – Tranceiver 1 (TR 1) setting (Continued)
IP network connection – Tranceiver 1 (TR 1) setting (Continued)
IP network connection – Tranceiver 1 (TR 1) setting (Continued)
– Tranceiver 1 (TR 1) setting (Continued)
– Tranceiver 1 (TR 1) setting (Continued)
Tranceiver 1 (TR 1) setting (Continued)
Tranceiver 1 (TR 1) setting (Continued)
setting (Continued)
setting (Continued)
Click [Connect] in IP network connection status ,
IP network connection status ,
IP network connection status ,
,,
and then confirm that During transmit appears in
During transmit appears in
During transmit appears in
appears in
appears in
Status .
Status .
..
2
2
3
This guide describes bridge and selective call mode
connection examples.
Read this guide after reading Installation guide q .
q
After making the connections as shown to the
left, turn transceivers A and C power ON, then
open the setting screen with your browser (see
Installation guide q).
w
Click Operating mode in the Connection
Operating mode in the Connection
Operating mode in the Connection
in the Connection
in the Connection
Connection
Connection
setting , and select Unicast mode in the
, and select Unicast mode in the
, and select Unicast mode in the
Unicast mode in the
Unicast mode in the
in the
in the
Transceiver 1 (TR 1): of IP communication
Transceiver 1 (TR 1): of IP communication
of IP communication
of IP communication
IP communication
IP communication
mode setting .
..
e
Click [Save and Reboot].
Select [Unicast mode] in both Area A and Area B.
Select
Clic
Clic
Clic
Enter
Confirm
The dialog shown below appears, and then click [OK].
NO E: IP network connection is initiali ed after
IP network connection is initiali ed after
connection is initiali ed after
is initiali ed after
is initiali ed after
changing IP communication mode setting .
IP communication mode setting ..
Save the VE-PG2 setting as a setting file, if
necessary.
Refer to the instruction manual (PDF file:
Download from the Icom web site) for details.
Approximately 30 seconds after clicking [OK], move
the mouse pointer to [BACK] and click. After system
reboots, the setting screen will open.
q
Click Transceiver 1 (TR 1) in IP network
Transceiver 1 (TR 1) in IP network
Transceiver 1 (TR 1) in IP network
in IP network
in IP network
IP network
IP network
connection setting in the Connection setting .
in the Connection setting .
in the Connection setting .
Connection setting .
Connection setting .
..
w
Input the Connection IP address in the IP network
IP network
IP network
connection .
..
(Example) Input 1 2.1 .0.3 to VE-PG2s in Area
1 2.1 .0.3 to VE-PG2s in Area
1 2.1 .0.3 to VE-PG2s in Area
to VE-PG2s in Area
to VE-PG2s in Area
A, and 1 2.1 .0.2 to VE-PG2s in
1 2.1 .0.2 to VE-PG2s in
1 2.1 .0.2 to VE-PG2s in
to VE-PG2s in
to VE-PG2s in
Area B illustrated to the left.
e
Click [Save].
Clic
Connection IP address for Area A 1 2.1 .0.3
Connection IP address for Area A 1 2.1 .0.3
for Area A 1 2.1 .0.3
for Area A 1 2.1 .0.3
1 2.1 .0.3
1 2.1 .0.3
Connection IP address for Area B 1 2.1 .0.2
Connection IP address for Area B 1 2.1 .0.2
for Area B 1 2.1 .0.2
for Area B 1 2.1 .0.2
1 2.1 .0.2
1 2.1 .0.2
Click Connect in both Area A and Area B.
Connect in both Area A and Area B.
Connect in both Area A and Area B.
in both Area A and Area B.
in both Area A and Area B.
Confirm Status in both Area A and Area B.
Status in both Area A and Area B.
Status in both Area A and Area B.
in both Area A and Area B.
in both Area A and Area B.