Icom VE-PG2 Installation Manual - page 4
2 Sets the VE-PG2 to Selective call mode
1 Connects transceivers and LAN to the VE-PG2
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
GROUND
q
e
w
r
[TRX2]
Calling number (DTMF): 2
To the [TRX2] port
To the [TRX1] port
(192.168.0.2)
[TRX1] Calling number (DTMF): 1
[Area A]
[Area B]
VE-PG2
Connect the transceiver’s microphone connector and speaker jack.
Transceiver A
channel 1
Transceiver C
channel 2
Transceiver B
channel 1
Transceiver D
channel 2
Connect the transceiver’s microphone connector and speaker jack.
NOTE: First, connect the transceiver
to the VE-PG2 using the specified
connection cable. Then turn ON the
power to the transceiver and the
VE-PG2.
NOTE: First, connect the transceiver
to the VE-PG2 using the specified
connection cable. Then turn ON the
power to the transceiver and the
VE-PG2.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable or connect the cables to [LAN]
may damage the VE-PG2, transceivers or repeaters.
Turn the transceivers’ power ON,
and then set the transceiver A
volume to the 12 o’clock position.
Turn the transceivers’ power ON,
and then set the transceiver C
volume to the 12 o’clock position.
Connect to the transceiver’s speaker jack.
Connect to the transceiver’s speaker jack.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable, or connecting the cables to
[LAN] may damage the VE-PG2, transceivers or repeaters.
NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.
Repeater’s rear panel
OPC-2074
ACC connector
MODE
DC
LAN
TRX1
TRX2
TRX3
IN
+
+
+
OUT
SW
ABC
Connect the specified cables to
[TRX1], [TRX2] or [TRX3] only.
Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.
*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.
1. O erating mode setting setting
O erating mode setting setting
O erating mode setting setting
setting
Select
Clic
1
2
Clic
Selective call mode setting
5. Ho to comm nicate
1
2
Confirm the Call destination number setting list as
Call destination number setting list as
Call destination number setting list as
as
as
shown below.
NO E:
• If you construct RoIP system with some VE-PG2s,
you can construct the system only to set each Call
Call
Call
destination number setting list .
..
• Call destination number setting list has below 3
Call destination number setting list has below 3
Call destination number setting list has below 3
buttons.
[Edit]
: Click this button to edit the index setting.
[Delete]
: Click this button to delete the index setting.
[Delete all] : Click this button to delete all data in the list.
3
2 Sets the VE-PG2 to Selective call mode (Continued)
This setting example refers to the connections in the far
top left illustration. Follow the steps for transceiver B calling
transceiver D.
q
Set Call destination number setting for the Area
Call destination number setting for the Area
Call destination number setting for the Area
for the Area
for the Area
B shown to the left.
(Example) Set Index to 2 , Call destination number
Index to 2 , Call destination number
Index to 2 , Call destination number
to 2 , Call destination number
to 2 , Call destination number
2 , Call destination number
2 , Call destination number
, Call destination number
, Call destination number
Call destination number
Call destination number
to 2 , Call destination VE-PG2 address
2 , Call destination VE-PG2 address
2 , Call destination VE-PG2 address
, Call destination VE-PG2 address
, Call destination VE-PG2 address
Call destination VE-PG2 address
Call destination VE-PG2 address
to 1 2.1 .0.2 and Call destination
1 2.1 .0.2 and Call destination
1 2.1 .0.2 and Call destination
and Call destination
and Call destination
Call destination
Call destination
VE-PG2 port to Transceiver 2(TR 2) .
to Transceiver 2(TR 2) .
to Transceiver 2(TR 2) .
Transceiver 2(TR 2) .
Transceiver 2(TR 2) .
..
w
Click [Save].
2
2. N m ering lan setting
N m ering lan setting
N m ering lan setting
setting
q
Move the mouse pointer to Connection setting ,
Connection setting ,
Connection setting ,
,,
and click Numbering plan .
Numbering plan .
Numbering plan .
..
w
Set Call destination number setting for the Area
A shown to the left.
(Example) Set Index to 1 , Call destination number
Index to 1 , Call destination number
Index to 1 , Call destination number
to 1 , Call destination number
to 1 , Call destination number
1 , Call destination number
1 , Call destination number
, Call destination number
, Call destination number
Call destination number
Call destination number
to 1 , Call destination VE-PG2 address
1 , Call destination VE-PG2 address
1 , Call destination VE-PG2 address
, Call destination VE-PG2 address
, Call destination VE-PG2 address
Call destination VE-PG2 address
Call destination VE-PG2 address
to 1 2.1 .0.2 and Call destination
1 2.1 .0.2 and Call destination
1 2.1 .0.2 and Call destination
and Call destination
and Call destination
Call destination
Call destination
VE-PG2 port to Transceiver 1(TR 1) .
to Transceiver 1(TR 1) .
to Transceiver 1(TR 1) .
Transceiver 1(TR 1) .
Transceiver 1(TR 1) .
..
e
Click [Save].
1
q
After making the connections as shown to the
above, turn transceivers A and C power ON, then
open the setting screen with your browser (see the
Installation guide q).
w
Click the Operating mode setting in the
Operating mode setting in the
Operating mode setting in the
in the
in the
Connection setting , and then select Selective
Connection setting , and then select Selective
, and then select Selective
, and then select Selective
Selective
Selective
call mode .
..
e
Click the [Save and Reboot] button.
r
Click [Back] on the screen after reboot finishes
(about 30 seconds later).
Click [OK] when the dialog box below appears.
• Connection setting will be return to default when
Connection setting will be return to default when
Connection setting will be return to default when
will be return to default when
will be return to default when
the Operating mode setting is modified.
Operating mode setting is modified.
Operating mode setting is modified.
setting is modified.
setting is modified.
• Save the VE-PG2 setting to the setting file, if
necessary.
Refer to the VE-PG2 instruction manual (PDF file:
Download from the Icom web site) for details.
Hold down transceiver B s [PTT], and push [2]
and [#] to transmit 2 and # DTMF signals to call to
transceiver D.
Release transceiver B s [PTT] to receive.
Transceiver D sounds beep tone, then star t
communication via the VE-PG2.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A- 3 W-3US
Printed in Japan
© 2010 Icom Inc.
4. ransceiver setting
Turn transceivers B and D power ON, and select the
same operating channel as transceivers A and C.
• Set the same channel for all the transceivers, to
communicate with the transceivers A and C.
See the transceiver s instruction manual when
setting the channel, if necessary.
(Example) I n t h e i l l u s t ra t i o n t o t h e l e f t , s e t
transceivers A and B (Area A) to channel
1, and transceivers C and D (Area B) to
channel 2.
2
This setting example refers to the connections in the far top
left illustration.
Select
Clic
Enter
Select
Select
Clic
Enter
Select
Confirm
While holding down transceiver D s [PTT], speak into
the microphone at your normal voice level.
Release transceiver D s [PTT] to receive.
While holding down transceiver B s [PTT], speak into
the microphone at your normal voice level.
Release transceiver B s [PTT] to receive.
3
4
VE-PG2 finishes communication when no audio is
applied to transceivers B and D for 15 seconds. Or hold
down the transceiver s [PTT] and [#] for 1 second to
transmit a # DTMF signal from the transceivers B or D.
5
3. ransceiver control setting
3. Transceiver control setting (Continued)
Select
Clic
Selective call mode setting
Selective call mode setting
Set transceivers A and C AF volume to the 12 o clock
clock
clock
position.
1
q
Move the mouse pointer to Connection setting
Connection setting
Connection setting
and then to the drop down menu TR E T , then
TR E T , then
TR E T , then
click Transceiver 1 (TR 1) .
w
Set Calling notice tone to Transceiver to Notice
Calling notice tone to Transceiver to Notice
Calling notice tone to Transceiver to Notice
Notice
Notice
tone 2 .
e
Set Send connect success tone to Transceiver to
Send connect success tone to Transceiver to
Send connect success tone to Transceiver to
Notice tone 2 .
Notice tone 2 .
r
Set Disconnect notice tone to Transceiver to
Disconnect notice tone to Transceiver to
Disconnect notice tone to Transceiver to
Notice tone 3 .
Notice tone 3 .
t
Set Send connect failure tone to Transceiver to
Send connect failure tone to Transceiver to
Send connect failure tone to Transceiver to
Notice tone 3 .
Notice tone 3 .
1
y
Click [Save].
u
Move the mouse pointer to Connection setting
Connection setting
Connection setting
and then to the drop down menu TR E T , then
click Transceiver 2 (TR 2) .
i
Set same steps as w–y.
1
Connect the VE-PG2 according to steps q – r in the illustration below.