Jandy AE-Ti Installation And Operation Manual - page 23
Page 21
You can change the temperature set point by
pressing the
Up
or
Down button
.
Repeatedly press
the Up or Down
button until you reach the desired
temperature set point. After 5 seconds of inactivity,
the new set point is stored in memory. When the water
temperature falls to 1 degree below the temperature
setting
and
after a 5 minute delay, the control will start
the heat pump and the associated right LED will light
RED.
5.2.5
Spa Mode - (Optional Maintain Heat)
If connected, the Maintain Heat mode allows the
heat pump to monitor the temperature of the water 24
hours a day.
When the water temperature drops below the
programmed temperature set point, the control will start
the heat pump.
To operate in spa mode with the Maintain Heat
feature, press
SPA
, then press
MENU,
press the
Down
button until
MAINTAIN SPA HEAT
is displayed, press
the
MENU
button. The associated left green LED
indicator will light and the unit will display
SET:XXX°.
Change the temperature set point by pressing the
Up
or
Down
button until the desired set point is displayed.
After 5 seconds of inactivity, the new set point is stored
in memory.
5.3
Operating Features of Hybrid Units
with Optional Chiller
NOTE
The chiller is an optional equipment. Not all
units are provided with chiller
.
5.3.1
Pool Mode - (Normal Chill)
To enable the pool mode, press
POOL
. The
associated left green LED indicator will light and the
unit will display
SET:XXX°
.
NOTE
XXX
represents the current temperature setting
on the control. The default setting for pool
temperature is 80°F (26°C).
Press the
MENU
button. P
ress the Up or Down
button until you reach
POOL CHILL
, press the
MENU
button. You can change the temperature set point by
pressing the
Up
or
Down button
.
Repeatedly press
the Up or Down
button until you reach the desired
temperature set point. After 5 seconds of inactivity,
the new set point is stored in memory. When the water
temperature rises to 1 degree above the temperature
setting
and
after a 5 minute delay, the control will start
the heat pump and the associated right LED will light
GREEN
.
5.3.2
Pool Mode - (Optional Maintain
Chill)
If connected, the Maintain Chill option mode
allows the unit to monitor the temperature of the
water 24 hours a day by turning the pool pump on and
sampling the water temperature. When the temperature
of the water rises above the desired temperature setting,
the control will then turn on the unit and the associated
right green LED will light.
To operate in pool mode with the Maintain Chill
feature, press
POOL
, then press
MENU
, then press
the
Down
button until
MAINTAIN POOL CHILL
is
displayed, press the
MENU
button. The associated
left green LED indicator will light and the unit will
display
SET:XXX°
. Change the temperature set point
by pressing the
Up
or
Down
button until the desired set
point is displayed. After 5 seconds of inactivity, the new
set point is stored in memory.
5.3.3
Spa Mode - (Optional Maintain Chill)
If connected, the Maintain Chill mode allows the
heat pump to monitor the temperature of the water 24
hours a day. When the water temperature rises above the
programmed temperature set point, the control will start
the heat pump.
To operate in the spa mode with the Maintain Chill
feature, press
SPA
, then press
MENU
, press the
Down
button until
MAINTAIN SPA CHILL
is displayed,
press the
MENU
button. The associated left green LED
indicator will light and the unit will display
SET:XXX°
.
Change the temperature set point by pressing the
Up
or
Down
button until the desired set point is reached.
After 5 seconds of inactivity, the new set point is stored
in memory.
5.4
User Setup Options
The User Setup options allow the user to select
specific Languages, Temperature Scale, Spa Timer, and
Display Light options.
5.4.1 Language
Setup
1.
Make sure the control is in the
OFF
mode.
2.
To enter the User Setup mode, press and hold the
MENU
button for 5 seconds.
NOTE The display will revert back to OFF after one
minute since the last key press.
3.
To select a language, use the
Up
or
Down
button
to display
SELECT USER SETUP LANGUAGE
.
Press the MENU button. The
SELECT
LANGUAGE ENGLISH
(default language)
appears, use the
Up
or
Down
button to scroll
through the language options. When you reach the