Jandy AquaLink RS Owner's Manual - page 13
12
How to check the AquaLink RS System:
Press the MENU button, then the FORWARD button and scroll
through until you reach SYSTEM SETUP. Hit ENTER, then Forward to
the DIAGNOSTICS Menu and press ENTER. The AquaLink RS
Display will display a list of various equipment and its status. If any
sensors read OPEN or SHORTED, consult your AquaLink Service
Representative.
About the Diagnostics Menu:
The DIAGNOSTICS Menu is used primarily by licensed AquaLink
Service Personnel to check the functionality of the system and to
troubleshoot. If there is a problem with your AquaLink RS, you
may want to review the DIAGNOSTIC Display to check for open
circuits.
About the Clear Memory Menu:
The
CLEAR MEMORY Menu allows you to clear all stored values
from the AquaLink RS Controller memory. All settings will be set to
their default settings. Stored values include auxiliary labels, all
programs, freeze protection settings, remote settings, and
thermostat setting. The time and date will not be cleared.
Only use the CLEAR MEMORY Menu in an emergency. Most
specific programs and settings can be canceled individually, using
the CANCEL button.
How to clear system memory:
1.
Press the MENU button, then the FORWARD button and scroll
through until you reach SYSTEM SETUP. Hit ENTER and then
FORWARD to CLR MEMORY. Hit ENTER again. The AquaLink RS
display will read PRESS ENTER TO CLEAR MEMORY, or CANCEL
TO ABORT.
2.
If you want to clear memory, press ENTER. Otherwise, press
CANCEL.
About the Battery Back-Up:
In the event of a power failure, DATE and TIME will be backed-up
by the 9-volt battery located in the Power Center enclosure. All
other programs and Menu setups do not require battery to store
information. To determine if battery is low, access DIAGNOSTICS
under the SYSTEM SETUP selection.
Battery is located behind the small door on the right side of the
Power Center panel and should be checked, if necessary
replaced, once a year.
About the Jandy Illuminator Color Wheel
Menu*:
From the AquaLink RS Control Panel, there is an option to
automatically rotate the Jandy Illuminator Color Wheel after a
preset time (30 seconds, one minute, five minutes, or continuous).
This requires the installation of a Jandy Landscape Illuminator,
Jandy Programmable Logic Controller and a Jandy Color Wheel
Module.
How to Operate the Jandy Illuminator Color
Wheel Menu*:
Under SYSTEM SETUP, use the forward or back arrow to move to
COLOR WHEELS, press enter. Warning messages will scroll across
the screen first, 1) WARNING: FOR JANDY LANDSCAPE
ILLUMINATOR ONLY, 2) WARNING: OPTIONAL COLOR WHEEL
MODULE(S) MUST BE INSTALLED. Select an AUX on the AquaLink
RS control panel to operate as a color wheel or press ENTER to end.
About the Solar Priority Menu*:
When solar and heater are enabled the solar will heat the water
until either the thermostat setting has been reached or solar heat
is no longer available. If there is not enough solar heat available to
reach the thermostat setting, solar heat will shut off and the other
heat source (usually gas heater) will take over to bring the water
up to the thermostat setting.
How to Operate the Solar Priority Menu*:
Under SYSTEM SETUP, use the forward or back arrow to move to
SOLR PRIORITY, press enter. Use the forward or back arrow button
to turn solar priority on or off. Press ENTER to return to the
information screen.
Using the Menu
About the In-Floor/Return Valve Switching
Menu*:
When the AquaLink RS is setup to control this feature, the "Solar
JVA" circuit will be activated every 20 minutes to switch a three
port valve from returning water through normal return lines to
sending the water to an in-floor cleaning system. If a solar system
is installed this circuit reverts to AUX 3. A JVA/AUX PC Board is
required.
How to Operate the In-Floor/Return Valve
Switching Menu*:
Under SYSTEM SETUP, use the forward or back arrow to move to IN
FLOOR CLN. Use the forward or back arrow button to turn IN FLOOR
CLN on or off. Press ENTER to return to the information screen.
*Rev. "I" PPD only