Jandy JXi 200 Installation And Operation Manual - Warning
Page 24
ENGLISH
Jandy
®
Pro Series, JXi
™
Gas-Fired Pool & Spa Heater
|
Installation & Operation Manual
Section 6. Electrical Connections
Wiring connections must be made exactly as shown in
the wiring diagram found on the inside of the heater door.
The NEC and CEC also require that the equipment and/
or appliances associated with the pool water circulating
system, including, but not limited to, pump motors and
heaters, be bonded together as part of the equipotential
bonding grid. Zodiac Pool Systems, Inc. provides a
special labeled bonding lug on the manifold side of the
heater to accommodate this requirement.
All electrical connections and wiring must be done by
a certified electrician only. Electrical wiring must also
be in accordance with the latest edition of the National
Electrical Code
®
(NEC
®
), ANSI
®
/National Fire Protection
Association
®
(NFPA
®
) 70, or in Canada, the Canadian
Electrical Code (CSA
®
C22.1) unless local code
requirements indicate otherwise.
The heater comes factory-wired for installation with 240
Volt, 60 Hz AC field electrical supply. If the use of 120
Volt, 60 Hz AC field electrical supply is required, You
must first change the position of the voltage selector
board on the power distribution board. See
Section
6.3
for
details
Part Number: H0402900 REV A (wiring diag) ; H0416500 REV A (note)
Description: JXi Heater - Wiring Diagram Label for inside front panel
Size: H0402900 REV A: 6.25 x 7 inches ; h0416500 REV A: 2.5 x 2.75
Color: Black
L1
F1
ACN1
ACH1
L2
F2
G
R
BK
BLOWER
MOTOR
BK
R
Y
BL
W
IGNITION CONTROL
F1
F2
24
VAC
FV+
FV-
IGN
120
L1
L2
IGN
FS
W
GND
VAL
BK
W
BK
BL
R
GY
BK
24 VAC
R
Y
HOT SURFACE
IGNITER
W
GY
W
TRANSFORMER
WATER
AquaLink RS
TEMP
GAS
VALVE
USER
INTERFACE1
BK O BL
R
HIPRESS/
HILIMIT
WATER
PRESS
REMOTE
SPA POOL COM
REV
VALVE
24VAC
PUMP
COMP/
IGN
FAN/
LOUVER
UNIVERSAL
CONTROLLER
POWER INTERFACE
UNIVERSAL
CONTROLLER
USER INTERFACE
POWER
INTERFACE
BK O BL R
AIR FLOW
SWITCH
GAS VALVE
WATER
TEMP
SENSOR
BL
W
BK
TO PUMP RELAY
CONTACTS (IF USED)
W
FUSE
R
Y
O
O
Y/BK
O
BR
Y
BR
Y
R
BL
BK
BK
BK
W
BK
BL
BR
Y
W
W
W
V
GY
BK
BK
PSW
Y/BK
C
NO
NC
Y/BK
COIL/AIR
TEMP
J3 CONNECT
OR
Factory Wired 24V
Factory Wired 120V/240V
BK - BLACK
BL - BLUE
B/BK - BLUE WITH BLACK TRACE
G/BK - GREEN WITH BLACK TRACE
PK - PINK
BR - BROWN
G - GREEN
GY - GRAY
O - ORANGE
R - RED
V - VIOLET
W - WHITE
Y - YELLOW
Y/BK - YELLOW WITH BLACK TRACE
120 VAC
HEATER
POWER
SUPPLY
Alternate 120V Wiring*
G
R
BK
NEUTRAL
HOT
Voltage Selector Card Must Be Rotated.
LIMIT
SWITCH
57˚C
(135˚F)
LIMIT
SWITCH
66˚C
(150˚F)
WATER
PRESS
SWITCH
NOTE: SI L’UN QUELQONQUE DES FILS
D’ORIGINE FOUMIS AVEC LE
CHAUFFE-PISCINE DOIT ÊTRE REMPLACÉ,
UN FIL POUR APPAREILS ÉLECTRIQUES À
TOLERANCE NOMINALE DE 105
°C DOIT
ÊTRE EMPLOYÉ. SI LE FIL PORTE LE
SYMBOLE ---------, LE REMPLACER
UNIQUEMENT PAR UN FIL POUR
APPAREILS ÉLECTRIQUES À TOLERANCE
NOMINALE DE 200°C.
NOTE: IF ANY OF THE ORIGINAL WIRE AS
SUPPLIED WITH THE HEATER MUST BE
REPLACED, APPLIANCE WIRING MATERIAL
RATED FOR 105°C MUST BE USED. WHERE
MARKED THUS - - - - - , APPLIANCE WIRING
MATERIAL RATED FOR 200°C MUST BE USED.
H0416500 Rev
B
die line, does not print
2.5 x 2.75
Accessory
Leads
Optional
VersaFlo™ Bypass Accessory
FL
TEMP
FOR AIR
LOUVER
STARTER
(IF USED)
G/BK
B/BK
PK
PK
VENT
TEMPERATURE
LIMIT
240°C
(464°F)
BYPASS
MOTOR
BYPASS
SWITCH
W
W
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
(j)
(k)
(l)
Figure 12. JXi Connections/ Schematic Wiring Diagram
WARNING
ELECTRICAL SHOCK HAZARD. This heater contains wiring that
carries high voltage. Contact with these wires may result in severe
injury or death.
CAUTION
Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation.
Verify proper operation after servicing.